Search NASA⌕ Search

SEARCH · Search NASA

Results for “SHAFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

SPC-71188 Rev 0 MARVEL Control Drum Rotary Shaft Seal Procurement Specification

Idaho National Laboratory (INL) is developing a microreactor to produce electrical power utilizing a small nuclear core under the Microreactor Application Research Validation and Evaluation (MARVEL) program. This procurement specification defines the requirements for fabrication of the MARVEL Control Drum Rotary Shaft Seal.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2023

Nonlinear analysis and vibro-impact characteristics of a shaft-bearing assembly

Here this study investigates the nonlinear frequency response of a shaft-bearing assembly with vibro-impacts occurring at the bearing clearances. The formation of nonlinear behavior as system parameters change is examined, along with the effects of asymmetries in the nominal, inherently symmetric system. The primary effect of increasing the forcing magnitude or decreasing the contact gap sizes is the formation of grazing-induced chaotic solution branches occurring over a wide frequency range near each system resonance. The system's nominal setup has very hard contact stiffness and shows no evidence of isolas or superharmonic resonances over the frequency ranges of interest. Moderate contact stiffnesses cause symmetry breaking and introduce superharmonic resonance branches of primary resonances. Even if some primary resonances are not present due to the system's inherent symmetry, their superharmonic resonances still manifest. Branches of quasiperiodic isolas (isolated resonance branches) are also discovered, along with a cloud of isolas near a high-frequency resonance. Parameter asymmetries are found to produce a few significant changes in behavior: asymmetric linear stiffness, contact stiffness, and gap size could affect the behavior of primary resonant frequencies and isolas.

42 ENGINEERING↗
DOE OSTI2021

Evaluation of several relevant fractionation processes as possible explanation for radioxenon isotopic activity ratios in samples taken near underground nuclear explosions in shafts and tunnels

Gas samples taken from two historic underground nuclear tests done in 1989 at the Nevada National Security Site (NNSS), formerly the Nevada Test Site (NTS), were examined to determine how xenon isotopes fractionate because of early-time cavity processes, transport through the rock, or dispersal through tunnels. Xenon isotopes are currently being used to distinguish civilian sources of xenon in the atmosphere from sources associated with underground nuclear explosions (UNEs). The two nuclear tests included (1) BARNWELL, a test conducted in a vertical shaft approximately 600 m below ground surface at Pahute Mesa, and (2) DISKO ELM, a horizontal line-of-sight test done in P-tunnel approximately 261 m below the surface of Aqueduct Mesa. Numerical flow and transport models developed for the two sites had mixed success when attempting to match the observed xenon isotope ratios. At the BARNWELL site, the simulated xenon isotope ratios were consistent with measurements from the chimney and ground surface and appeared to have been affected primarily by fractionation during subsurface transport. At the DISKO ELM site, samples taken from two elevations in the chimney failed to show the degree of fractionation predicted by the models during transport and did not show evidence for significant fractionation due to early-time condensation of refractory xenon-precursor radionuclides into the melt glass. Gas samples taken from the adjacent tunnels in the days following the test showed mixed evidence for early-time separation of xenon isotopes from their iodine precursors.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Probe measurements of electric field and electron density fluctuations at megahertz frequencies using in-shaft miniature circuits

In this work, a four-tip electrostatic probe is constructed to measure high-frequency (0.1–10 MHz) fluctuations in both the electric field (one component) and electron density in a laboratory plasma. This probe also provides data for the local electron temperature and density. Circuits for high-frequency measurements are fabricated on two miniature boards, which are embedded in the probe shaft, near the tips to minimize the pickup of common-mode signals. The amplitude and phase response of two circuits to sinusoidal test signals are measured and compared with results from modeling. For both circuits, the phase shift between input and output signals is relatively small (<30°). The performance of the probe is verified in a high-density (~10 13 cm –3 ) and low-temperature (≲10 eV) plasma. The probe successfully measures high-frequency (~2 MHz) fluctuations in the electric field and density, which are associated with lower hybrid drift waves. This probe can provide information on the wave-associated anomalous drag, which can be compared with the classical resistivity.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

MAGIS-100 Experiment Installation in Shaft

This poster shows the experiment and access system as it will be installed in the MINOS shaft, along with important connecting components such as the atom sources and connection nodes.

Kowalkowski, James B. [Fermilab]↗
NASA NTRS1966

Shaft encoder presents digital output

Circuits that include compensation circuitry time a capacitance relative to a reference voltage so that a digital presentation occurs that is representative of the positional condition of the mechanical shaft being monitored. This circuitry may be employed in multiples to furnish binary encoding of a number of rotating devices simultaneously.

Hillis, D. A.↗
NASA NTRS1968

Accumulator for shaft encoder

Digital accumulator relies almost entirely on integrated circuitry to process the data derived from the outputs of gyro shaft encoder. After the read command is given, the output register collects and stores the data that are on the set output terminals of the up-down counters.

Carroll, C. C.↗