Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Ab-initio molecular modeling of interfaces in tantalum-carbon system

Processing of ultrahigh temperature TaC ceramic material with sintering additives of B{sub 4}C and reinforcement of carbon nanotubes (CNTs) gives rise to possible formation of several interfaces (Ta{sub 2}C-TaC, TaC-CNT, Ta{sub 2}C-CNT, TaB{sub 2}-TaC, and TaB{sub 2}-CNT) that could influence the resultant properties. Current work focuses on interfaces developed during spark plasma sintering of TaC-system and performing ab initio molecular modeling of the interfaces generated during processing of TaC-B{sub 4}C and TaC-CNT composites. The energy of the various interfaces has been evaluated and compared with TaC-Ta{sub 2}C interface. The iso-surface electronic contours are extracted from the calculations eliciting the enhanced stability of TaC-CNT interface by 72.2%. CNTs form stable interfaces with Ta{sub 2}C and TaB{sub 2} phases with a reduction in the energy by 35.8% and 40.4%, respectively. The computed Ta-C-B interfaces are also compared with experimentally observed interfaces in high resolution TEM images.

36 MATERIALS SCIENCE↗

Operation of a high-gradient superconducting radio-frequency cavity with a non-evaporable getter pump

The use of non-evaporable getter (NEG) pumps in particle accelerators has increased significantly over the past few years because of their large pumping speed, particularly for hydrogen, compared to the size of the pump. A concern about using such pumps in superconducting radio-frequency (SRF) accelerators is the possibility of shedding particulates which could then migrate into the SRF cavities and produce field emission, therefore degrading the cavity performance. One option to mitigate such issue is to use sintered getter materials which intrinsically offer superior mechanical and particle retention properties. In this article we present the results from cryogenic RF tests of a high-gradient SRF cavity after being evacuated several times with an NEG pump equipped with sintered getter disks and placed in close proximity to the cavity. Here, the results showed that the cavity performance was not affected by the pump up to the quench gradient of 34 MV/m. As a result of this study, two such NEG pumps have been installed next to a cryomodule in the CEBAF accelerator to maintain ultra-high vacuum in the SRF cryomodule and two adjacent warm girder sections.

43 PARTICLE ACCELERATORS↗

Zn migration during spark plasma sintering of thermoelectric Zn{sub 4}Sb{sub 3}

The phase homogeneity of spark plasma sintered thermoelectric Zn{sub 4}Sb{sub 3} pellets along the pressing direction has been studied by potential Seebeck microprobe scanning and spatially resolved x-ray diffraction. Significant variations in the Seebeck coefficient reflect presence of different crystalline phases. The emergence of the ZnSb phase at the bottom of the pellet and metallic Zn impurity at the top explains the variation in the Seebeck coefficients. Quantitative phase distributions along the pressing axis were determined from the Rietveld refinements of spatially resolved x-ray diffraction patterns. These reveal a migration of highly mobilized Zn atoms under the direct current applied during spark plasma sintering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A Preliminary Analysis of Dose Rates Associated with ITER CVCS Equipment/Area Location

A preliminary analysis of the ITER Chemical and Volume Control System (CVCS) Area was performed to assess dose rates outside the walls and ceiling of the facility after 1.5 years of operation at shutdown, 2 days, and 10 days after shutdown. For this purpose a simplified Monte Carlo computer model was developed using the MCNP (MCNP5 Ver. 1.51) code. Two components are included: the smaller filter tank and the larger ion exchanger. These pieces of equipment are associated with the Integrated Blanket ELM Divertor Primary Heat Transfer System, which will have the largest dose rates associated with activated corrosion products during operation in comparison with other systems. The ion exchanger contained two source regions, a 1.2-m-thick resin bed above a 0.55 m-thick skirt, and a 0.8-m-thick water region. The filter constituted an additional source. Thus the model consisted of three sources (filter, resin, water), homogeneously distributed within the appropriate source regions. However, much of the results (that address individual isotopes) are presented with the two sources in the ion exchanger combined. In these cases the sources are referred to as the 'ion exchanger source' and the 'filter source.' Dimensions for the facility and components, as well as source isotopes and strengths, and material densities, were supplied by US ITER. Because of its simplification, the model does not contain pipes. Consequently, radiation streaming through pipe penetrations, radiation emanating from the pipes, and shielding from the pipes were not considered in this analysis. Dose rates on the outside of two walls and the ceiling were calculated. The two walls are labeled as the 'long' wall (aligned with the X-axis) and the 'short' wall (aligned with the Y-axis). These walls and ceiling were nominally set to 30-cm-thick concrete. In the original analysis, standard concrete (2.3 g/cc density) was used. In addition to the shielding walls/ceiling, a floor and an additional wall opposite the long wall were added for photon scattering contributions. These were both 10-cm-thick, standard concrete structures. Other components (tanks, pipes, etc.), that were not included in the model, would potentially add additional scattering and shielding. Possibly these additional effects will be addressed in a later, more detailed analysis. The room was 29.6 m in length (X-axis), but was limited to 15 m in the model. The inside width (Y axis) and height (Z axis) were 4 m and 3.4 m, respectively. The origin for the model was located inside the room at the corner opposite the long wall and adjacent to the short wall at the floor level. The room was filled with air at standard temperature and pressure. The stainless steel (SS304) wall thicknesses for the ion exchanger and filter were 2.2 cm and 0.8 cm, respectively. The axial center of the filter was located 140 cm from the short wall and 100 cm from the long wall (outer surface). The axial center of the ion exchanger was located 440 cm from the short wall and 250 cm from the long wall (inner surface). The resin was assumed to be a homogeneous mixture of equal atom density fractions of hydrogen and carbon* at a specified density of 1.136 g/cc. The filter material was assumed to be homogeneous carbon at a specified density of 1.8 g/cc. If the filter media were stainless steel and the accumulated activity were the same, the dose rate outside the filter would be lower, provided the density of the stainless steel sintered filter material is significantly higher than 1.8g/cc. The densities of the water and air were assumed to be 1.0 g/cc and 1.096E-3 g/cc, respectively. The model included 10 small volumes placed outside the model adjacent to the wall at locations where the dose rates were expected to be highest and which showed to a degree the fall-off of the dose rate with distance along a particular wall or ceiling. These 'tally cells' are shown in Fig. 2 and are described in Table 1. Each cell had dimensions of 50 cm x 50 cm x 1 cm and was oriented so that the 1-cm-thick dimension was perpendicular to the wall against which the cell was located. Also, smaller tally volumes were placed at 5 cm (updated model), 30 cm, 50 cm, and 100 cm from each source, both radially from the outside of each component at the height of each source mid-plane, and vertically, along the axial centerline, above the ion-exchanger and below the filter. (For the ion exchanger, the vertical distance was limited to 75 cm because of interference from the ceiling.) These tally regions can be seen in Fig. 3. Each cell had dimensions of 5 cm x 5 cm x 1 cm, oriented so that the 1-cm-thick dimension was perpendicular to the X, Y or Z axis.

08 HYDROGEN↗

Composite materials formed with anchored nanostructures

A method of forming nano-structure composite materials that have a binder material and a nanostructure fiber material is described. A precursor material may be formed using a mixture of at least one metal powder and anchored nanostructure materials. The metal powder mixture may be (a) Ni powder and (b) NiAl powder. The anchored nanostructure materials may comprise (i) NiAl powder as a support material and (ii) carbon nanotubes attached to nanoparticles adjacent to a surface of the support material. The process of forming nano-structure composite materials typically involves sintering the mixture under vacuum in a die. When Ni and NiAl are used in the metal powder mixture Ni.sub.3Al may form as the binder material after sintering. The mixture is sintered until it consolidates to form the nano-structure composite material.

36 MATERIALS SCIENCE↗

Diffraction Studies of the Atomic Vibrations of Bulk and Surface Atoms in the Reciprocal and Real Spaces of Nanocrystalline SiC

To describe and evaluate the vibrational properties of nanoparticles it is necessary to distinguish between the surface and the core of the particles. Theoretical calculations show that vibrational density of states of the inner atoms of nanograins is similar to bulk material but shifted to higher energies which can be explained by the fact that the gain core is stressed (hardened) due to the presence of internal pressure. Theoretical calculations also show that there is a difference between vibrational properties of a crystal lattice of the grain interior in isolated particles and in a dense (sintered) nanocrystalline material. This is probably due to a coupling of the modes inside the grains via the grain boundaries in dense nanocrystalline bodies. We examined strains present in the surface shell based on examination of diamond and Sic nanocrystals in reciprocal (Bragg-type scattering) and real (PDF analysis) space analysis of neutron diffraction data. Recently we examined the atomic thermal motions in nanocrystalline Sic based on the assumption of a simple Einstein model for uncorrelated atomic notions. According to this model, the Bragg intensity is attenuated as a function of scattering angle by the Debye-Waller factor. Based on this assumption overall temperature factors were determined from the Wilson plots.

Stelmakh, S.↗

Effects of Sintering Temperature on the Porosity and Mechanical Behavior of Porous Titanium Scaffolds Prepared by Freeze-Casting

The purpose of this study was to investigate the effects of sintering temperature on the microstructure, and associated mechanical properties of porous titanium scaffolds prepared by freeze-casting. Sintering temperature significantly influenced the porosity and the mechanical properties of the titanium scaffolds. The porosity decreased from 60 to 20% as the sintering temperatures increased from 800 to 1100 °C. The scaffolds were of an open pore structure with pore sizes ranging from 2 to 20 μm. The average wall thickness of the porous titanium was measured, using a micro-computed tomography, to be in the range from 9.2 to 26.2 μm. Elastic modulus was between 2 to 7 GPa, depending on vacuum annealing conditions. The compression strength of the scaffolds may exceed 1000 MPa as the sintering temperature higher than 1000 °C. The increase in titanium strength and stuffiness could be mainly attributed to the decrease in porosity as well as the increase in wall thickness.

36 MATERIALS SCIENCE↗

In situ microscopy of rapidly heated nano-Al and nano-Al/WO{sub 3} thermites

The initiation and reaction mechanism of nano-Al and nano-Al thermites in rapid heating environments is investigated in this work. A semiconductor-based grid/stage was used, capable of in situ heating of a sample from room temperature to 1473 K, and at a rate of 10{sup 6} K/s, inside an electron microscope. Nano-Al was rapidly heated in a transmission electron microscope, and before and after images indicate that the aluminum migrates through the shell, consistent with a diffusion-based mechanism. A nano-Al/WO{sub 3} composite was then heated in a scanning electron microscope. The results indicate that a reactive sintering mechanism is occurring for the nano-Al/WO{sub 3} thermite, as the products are found to be in surface contact and significantly deformed after the heating pulse.

36 MATERIALS SCIENCE↗

The effect of high-power transient events on tungsten and tungsten coatings used for radio frequency launcher applications

High-temperature plasma-facing material coatings used for radio frequency (RF) launchers need to be robust enough to survive RF breakdown arcing or other transient events from the plasma (e.g., an edge localized mode) without causing a catastrophic failure of the coating. High-power transient effects are being explored by using an RF-induced vacuum arc to determine the robustness of tungsten coatings made by a variety of manufacturing methods. A 1/4-wavelength resonant section of vacuum transmission line terminated with an open circuit electrode structure with a well-defined electric field (30-60 kV/mm) produces repeatable arcing conditions. The initial focus is on tungsten as a plasma-facing material, including sintered tungsten, tungsten coatings on steel produced via physical vapor deposition (PVD), and functionally graded tungsten/steel coatings deposited by low-pressure plasma-spraying (LPPS). Thin PVD coatings (1-2 microns) fail catastrophically from an arc and result in severe delamination of the coating. The arc-induced damage of thicker coatings, such as those made via LPPS, tend to be restricted to the top few microns of the surface. Arcing often initiates on sharp surface microstructures and causes localized melting of tungsten at the surface of all the materials studied and results in resolidified melt pools with surface cracks. The resolidified surface results in a reduction in overall deuterium retention when exposed to typical RF plasma sheath conditions.

Caughman, John [ORNL] (ORCID:0000000206091164)↗

Microstructural analysis and thermoelectric properties of Sn-Al co-doped ZnO ceramics

Sn-Al co-doped polycrystalline ZnO ceramics were prepared by sintering in air. Phase and microstructure analysis was performed by X-ray diffraction and SEM-EDS and thermoelectric properties were measured. XRD analysis showed a ZnO primary phase as well as secondary phase peaks due to the formation of a Zn{sub 2}SnO{sub 4} spinel phase or SnO{sub 2}(ZnO:Sn-Al){sub m} intergrowth phase. SEM analysis revealed a dense microstructure with a small number of nanometric pores, consistent with the measured density of 5.48 g/cm{sup 3}. An activated electrical conductivity characteristic of a semiconducting material was observed as well as a negative Seebeck coefficient with both values increasing in absolute value from RT to 730 °C. The power factor had a maximum value of 3.73×10{sup −4} W m{sup −1} K{sup −2} at 730 °C. Thermal conductivity measurements showed a significant reduction over the measured temperature range compared to undoped ZnO. This could be attributed to grain size reduction, the formation of a nanoscale secondary phase or a reduction in crystallinity caused by Sn-Al co-doping. A maximum ZT of 0.06 was obtained at 750 °C for the Sn-Al co-doped ZnO ceramics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermoelectric Properties of TiNiSn Half Heusler Alloy Obtained by Rapid Solidification and Sintering

Thermoelectric TiNiSn-based half Heusler compound reveals high Seebeck coefficient and electrical conductivity, leading to high power factor. As a consequence of the solidification path, TiNiSn single phase cannot be obtained directly from the liquid phase. Thus, a long annealing step is needed to homogenize the alloy. In this work, we present a new processing route for half Heusler compound formation, combining arc melting of pure elements, rapid solidification of the molten alloy and sintering. Rapid solidification of the molten alloy allows to obtain almost single TiNiSn phase, limiting the formation of the primary TiNi{sub 2}Sn phase as a consequence of the deep undercooling of the liquid. The rapidly solidified alloy was ground to powder and sintered by open die pressing. As-sintered samples show a density around 95% of the theoretical value. Thermal cycling of the sintered samples shows evolution of the phases, suggesting that after sintering the sample is not in equilibrium yet. After the second thermal cycle thermoelectric properties become reproducible, indicating the attainment of the equilibrium. In conclusion, the proposed processing route allows to obtain dense TiNiSn in bulk form avoiding the time-consuming annealing step, typically used to homogenize this alloy after solidification.

36 MATERIALS SCIENCE↗

Improvement of the electrochromic response of a low-temperature sintered dye-modified porous electrode using low-resistivity indium tin oxide nanoparticles

An indium tin oxide (ITO) nanoparticle-based porous electrode sintered at low temperatures was investigated as a transparent electrode for electrochromic displays (ECDs). The electrochromic (EC) response of the dye-modified ITO porous electrode sintered at 150 °C, which exhibited a generally low resistivity, was markedly superior to that of a conventional dye-modified TiO{sub 2} porous electrode sintered at the same temperature. Moreover, the EC characteristics of the dye-modified ITO porous electrode sintered at 150 °C were better than those of the high-temperature (450 °C) sintered conventional dye-modified TiO{sub 2} porous electrode. These improvements in the EC characteristics of the dye-modified ITO porous electrode are attributed to its lower resistivity than that of the TiO{sub 2} porous electrodes. In addition to its sufficiently low resistivity attained under the sintering conditions required for flexible ECD applications, the ITO porous film had superior visible-light transparency and dye adsorption capabilities. We conclude that the process temperature, resistivity, optical transmittance, and dye adsorption capability of the ITO porous electrode make it a promising transparent porous electrode for flexible ECD applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Transparent conducting impurity-doped ZnO thin films prepared using oxide targets sintered by millimeter-wave heating

The preparation of transparent conducting impurity-doped ZnO thin films by both pulsed laser deposition (PLD) and magnetron sputtering deposition (MSD) using impurity-doped ZnO targets sintered with a newly developed energy saving millimeter-wave (28 GHz) heating technique is described. Al-doped ZnO (AZO) and V-co-doped AZO (AZO:V) targets were prepared by sintering with various impurity contents for 30 min at a temperature of approximately 1250 degree sign C in an air or Ar gas atmosphere using the millimeter-wave heating technique. The resulting resistivity and its thickness dependence obtainable in thin films prepared by PLD using millimeter-wave-sintered AZO targets were comparable to those obtained in thin films prepared by PLD using conventional furnace-sintered AZO targets; a low resistivity on the order of 3x10{sup -4} {Omega} cm was obtained in AZO thin films prepared with an Al content [Al/(Al+Zn) atomic ratio] of 3.2 at. % and a thickness of 100 nm. In addition, the resulting resistivity and its spatial distribution on the substrate surface obtainable in thin films prepared by rf-MSD using a millimeter-wave-sintered AZO target were almost the same as those obtained in thin films prepared by rf-MSD using a conventional powder AZO target. Thin films prepared by PLD using millimeter-wave-sintered AZO:V targets exhibited an improved resistivity stability in a high humidity environment. Thin films deposited with a thickness of approximately 100 nm using an AZO:V target codoped with an Al content of 4 at. % and a V content [V/(V+Zn) atomic ratio] of 0.2 at. % were sufficiently stable when long-term tested in air at 90% relative humidity and 60 degree sign C.

36 MATERIALS SCIENCE↗

Preparation of mesoporous titanium dioxide anode by a film- and pore-forming agent for the dye-sensitized solar cell

Highlights: • PVP is used as a film- and pore-forming agent to prepare the mesoporous TiO{sub 2} anode. • The TiO{sub 2} anode supplies high surface area for the dye adsorption. • The DSSC efficiency is strongly dependent on the pore properties of the TiO{sub 2} anode. • The DSSC efficiency with the TiO{sub 2} anode prepared by 20 wt% PVP reaches 8.39%. - Abstract: A novel mean of generating mesoporous titanium dioxide (TiO{sub 2}) anodes by employing polyvinylpyrrolidone (PVP) as the film- and pore-forming agent are proposed for dye-sensitized solar cells (DSSCs). The influences on the morphology and photovoltaic performances of the TiO{sub 2} anodes are investigated by adjusting the PVP content in synthesizing the mesoporous TiO{sub 2} anodes. The photovoltaic conversion efficiency of the DSSC is found to be strongly dependent on the pore properties of the TiO{sub 2} anode. After the sintering process, the removal of the PVP leaves porously interconnected channel structures inside the TiO{sub 2} anode, supplying enhanced specific surface area for the dye adsorption as well as the efficient electron transmission. As a result, the TiO{sub 2} anode prepared by 20 wt% PVP presents the highest performances, based on which the DSSC achieves the highest conversion efficiency of 8.39%, approximately increased by 56.53% than that of the DSSC fabricated without PVP (5.36%).

36 MATERIALS SCIENCE↗

Effects of Se substitution on the thermoelectric performance of n-type Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} skutterudites

Highlights: ► The simple solid state reaction technique was employed to prepare Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} skutterudites. ► The thermal conductivity decreases gradually with the increasing Se content. ► Doping with moderate Se is an effective way to enhance the thermoelectric performance of Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x}. ► The highest ZT of 1.11 at 800 K is obtained for the Co{sub 4}Sb{sub 11.3}Te{sub 0.58}Se{sub 0.12} sample. -- Abstract: A series of double-substituted Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} skutterudites have been fabricated by combining the solid state reaction and the spark plasma sintering method, and the effects of Se substitution on the thermoelectric properties are characterized by measurements of the electrical conductivity, the Seebeck coefficient and the thermal conductivity in the temperature range of 300–800 K. Doping Se into the Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x} matrix suppresses the carrier concentration, and the electrical conductivity actually decreases with the Se content. However, moderate Se doping is effective in enhancing the thermoelectric performance of the n-type Co{sub 4}Sb{sub 11.3}Te{sub 0.7−x}Se{sub x}, because of the resulted dramatically decreased thermal conductivity. Analyses indicate that the heightened point-defect scattering induced by Se doping together with the electron–phonon scattering induced by Te doping is responsible for the reduction of lattice thermal conductivity of these compounds.

36 MATERIALS SCIENCE↗

Study of microstructure and semiconductor to metallic conductivity transition in solid state sintered Li{sub 0.5}Mn{sub 0.5}Fe{sub 2}O{sub 4−δ} spinel ferrite

Li{sub 0.5}Mn{sub 0.5}Fe{sub 2}O{sub 4} ferrite has been prepared by solid state sintering route. XRD pattern showed single phased cubic spinel structure. The samples exhibited typical character of plastoferrite with ring shaped surface microstructure. New feature observed in the present ferrite is the frequency activated conductivity transition from semiconductor to metallic state above 800 K. The increase of conductivity with frequency in the semiconducting regime follows Jonscher power law, while decrease of conductivity in metallic regime obeys Drude equation. The conductivity in semiconductor regime has been understood by hopping mechanism of localized charge carriers among the cations in B sites of cubic spinel structure. At higher temperatures, overlapping of electronic orbitals from neighbouring ions and free particle like motion of lighter Li{sup +} ions among interstitial lattices contributed metallic conductivity. The samples provided evidence of localized nature of the charge carriers at lower temperatures and increasing delocalized character with the increase of measurement temperature. From application point of view, such ferrites behave as semiconductor at low temperature and allow electromagnetic wave to pass through, but transform into a metallic reflector with negative dielectric constant at high temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Calcium silicate ceramic scaffolds toughened with hydroxyapatite whiskers for bone tissue engineering

Calcium silicate possessed excellent biocompatibility, bioactivity and degradability, while the high brittleness limited its application in load-bearing sites. Hydroxyapatite whiskers ranging from 0 to 30 wt.% were incorporated into the calcium silicate matrix to improve the strength and fracture resistance. Porous scaffolds were fabricated by selective laser sintering. The effects of hydroxyapatite whiskers on the mechanical properties and toughening mechanisms were investigated. The results showed that the scaffolds had a uniform and continuous inner network with the pore size ranging between 0.5 mm and 0.8 mm. The mechanical properties were enhanced with increasing hydroxyapatite whiskers, reached a maximum at 20 wt.% (compressive strength: 27.28 MPa, compressive Young's modulus: 156.2 MPa, flexural strength: 15.64 MPa and fracture toughness: 1.43 MPa·m{sup 1/2}) and then decreased by addition of more hydroxyapatite whiskers. The improvement of mechanical properties was due to whisker pull-out, crack deflection and crack bridging. Moreover, the degradation rate decreased with the increase of hydroxyapatite whisker content. A layer of bone-like apatite was formed on the scaffold surfaces after being soaked in simulated body fluid. Human osteoblast-like MG-63 cells spread well on the scaffolds and proliferated with increasing culture time. These findings suggested that the calcium silicate scaffolds reinforced with hydroxyapatite whiskers showed great potential for bone regeneration and tissue engineering applications. - Highlights: • HA whiskers were incorporated into CS to improve the properties. • The scaffolds were successfully fabricated by SLS. • Toughening mechanisms was whisker pull-out, crack deflection and bridging. • The scaffolds showed excellent apatite forming ability.

36 MATERIALS SCIENCE↗

Origin of giant permittivity and high-temperature dielectric anomaly behavior in Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics

Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics prepared by the conventional solid-state reaction method under various sintering conditions were found to exhibit a giant dielectric constant over 10 000 around room temperature. Two electrical responses were observed in the combined modulus and impedance plots, indicating the presence of Maxwell-Wagner relaxation. The contributions of semiconducting grains and insulating grain boundaries (corresponding to high-frequency and low-frequency electrical response, respectively) played important roles in the dielectric properties of Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics. The correlations between grain boundaries resistance and low frequency dielectric loss, grains resistance and the position of dielectric loss peak were addressed. Mixed-valent structures of Cu{sup 2+}/Cu{sup 3+} and Ti{sup 3+}/Ti{sup 4+} had been determined using X-ray photoelectron spectroscopy. Electron hopping between Cu{sup 2+} and Cu{sup 3+} and electron transport in Ti{sup 3+}-O-Ti{sup 4+} paths were proposed as the origin of the semiconducting nature of Na{sub 0.5}Y{sub 0.5}Cu{sub 3}Ti{sub 4}O{sub 12} ceramics. In particular, high-temperature dielectric anomaly behavior was investigated in detail. A dielectric peak exhibiting relaxor-like behavior was observed around 200 Degree-Sign C, which was linked with the formation of oxygen vacancies. Based on the electric modulus results, this behavior was explored in the light of the defect formation and explained in terms of a competition process depending on the combinational contribution to polarization between n- and p-type carriers rather than a relaxation process.

36 MATERIALS SCIENCE↗