SEARCH · Search NASA

Results for “SOUND RANGING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS2006

A Computational Study of the Flow Physics of Acoustic Liners

The present investigation is a continuation of a previous joint project between the Florida State University and the NASA Langley Research Center Liner Physics Team. In the previous project, a study of acoustic liners, in two dimensions, inside a normal incidence impedance tube was carried out. The study consisted of two parts. The NASA team was responsible for the experimental part of the project. This involved performing measurements in an impedance tube with a large aspect ratio slit resonator. The FSU team was responsible for the computation part of the project. This involved performing direct numerical simulation (DNS) of the NASA experiment in two dimensions using CAA methodology. It was agreed that upon completion of numerical simulation, the computed values of the liner impedance were to be sent to NASA for validation with experimental results. On following this procedure good agreements were found between numerical results and experimental measurements over a wide range of frequencies and sound-pressure-level. Broadband incident sound waves were also simulated numerically and measured experimentally. Overall, good agreements were also found.

Tam, Christopher↗

NASA NTRS2007

Rapid and Quiet Drill

This describes aspects of the rapid and quiet drill (RAQD), which is a prototype apparatus for drilling concrete or bricks. The design and basic principle of operation of the RAQD overlap, in several respects, with those of ultrasonic/ sonic drilling and coring apparatuses described in a number of previous NASA Tech Briefs articles. The main difference is that whereas the actuation scheme of the prior apparatuses is partly ultrasonic and partly sonic, the actuation scheme of the RAQD is purely ultrasonic. Hence, even though the RAQD generates considerable sound, it is characterized as quiet because most or all of the sound is above the frequency range of human hearing.

Sherrit, Stewart↗

NASA NTRS2013

Visible Contrast Energy Metrics for Detection and Discrimination

Contrast energy was proposed by Watson, Robson, & Barlow as a useful metric for representing luminance contrast target stimuli because it represents the detectability of the stimulus in photon noise for an ideal observer. Like the eye, the ear is a complex transducer system, but relatively simple sound level meters are used to characterize sounds. These meters provide a range of frequency sensitivity functions and integration times depending on the intended use. We propose here the use of a range of contrast energy measures with different spatial frequency contrast sensitivity weightings, eccentricity sensitivity weightings, and temporal integration times. When detection threshold are plotting using such measures, the results show what the eye sees best when these variables are taken into account in a standard way. The suggested weighting functions revise the Standard Spatial Observer for luminance contrast detection and extend it into the near periphery. Under the assumption that the detection is limited only by internal noise, discrimination performance can be predicted by metrics based on the visible energy of the difference images

Ahumada, Albert↗

NASA NTRS2022

Atmospheric Waves and Global Seismoacoustic Observations of the January 2022 Hunga Eruption, Tonga

The 15 January 2022 climactic eruption of Hunga volcano, Tonga, produced an explosion in the atmosphere of a size that has not been documented in the modern geophysical record. The event generated a broad range of atmospheric waves observed globally by various ground-based and spaceborne instrumentation networks. Most prominent was the surface-guided Lamb wave (≲0.01 hertz), which we observed propagating for four (plus three antipodal) passages around Earth over 6 days. As measured by the Lamb wave amplitudes, the climactic Hunga explosion was comparable in size to that of the 1883 Krakatau eruption. The Hunga eruption produced remarkable globally detected infrasound (0.01 to 20 hertz), long-range (~10,000 kilometers) audible sound, and ionospheric perturbations. Seismometers worldwide recorded pure seismic and air-to-ground coupled waves. Air-to-sea coupling likely contributed to fast-arriving tsunamis. Here, we highlight exceptional observations of the atmospheric waves.

Robin S Matoza↗

NASA NTRSDate not supplied

NASA Investigation of Flow Direction Effects on Impedance Eduction for Acoustic Liners

In support of a collaboration with the International Forum for Aviation Research (IFAR), the NASA Langley Liner Physics Team has acquired a detailed dataset for use in the evaluation of flow direction effects on the acoustic liner impedance eduction process. Measurements are acquired with four acoustic liners designed to cover a range of sensitivities to source sound pressure level and tangential mean flow effects, specifically at source levels of 120 and 140 dB and centerline Mach numbers of 0.0, 0.1, 0.2, and 0.3. These measurements include detailed flow profile surveys upstream and downstream of the liner test window, as well as acoustic pressure data over the extent of the test window. The results clearly demonstrate the importance of the choice of Mach number used in the impedance eduction analysis. Average Mach number differences of less than 0.01 result in significant variation in the educed impedance spectra. These data will soon be supplied to the IFAR partners and will be made available for the general public within the next year.

acoustic↗

NASA NTRSDate not supplied

NASA Investigation of Flow Direction Effects on Impedance Eduction for Acoustic Liners

acoustic↗

NASA NTRS1987

Effects of fiber motion on the acoustic behavior of an anisotropic, flexible fibrous material

The acoustic behavior of a flexible fibrous material was studied experimentally. The material consisted of cylindrically shaped fibers arranged in a batting with the fibers primarily aligned parallel to the face of the batting. This type of material was considered anisotropic, with the acoustic propagation constant depending on whether the dirction of sound propagation was parallel or normal to the fiber arrangement. Normal incidence sound absorption measurements were taken for both fiber orientations over the frequency range 140 to 1500 Hz and with bulk densities ranging from 4.6 to 67 kg/cu m. When the sound propagated in a direction normal to the fiber alignment, the measured sound absorption showed the occurrence of a strong resonance, which increased absorption above that attributed to viscous and thermal effects. When the sound propagated in a direction parallel to the fiber alignment, indications of strong resonances in the data were not present. The resonance in the data for fibers normal to the direction of sound propagation is attributed to fiber motion. An analytical model was developed for the acoustic behavior of the material displaying the same fiber motion characteristics shown in the measurements.

Dahl, Milo D.↗

NASA NTRS1990

Effects of fiber motion on the acoustic behavior of an anisotropic, flexible fibrous material

The acoustic behavior of a flexible fibrous material was studied experimentally. The material consisted of cylindrically shaped fibers arranged in a batting with the fibers primarily aligned parallel to the face of the batting. This type of material was considered anisotropic, with the acoustic propagation constant depending on whether the direction of sound propagation was parallel or normal to the fiber arrangement. Normal incidence sound absorption measurements were taken for both fiber orientations over the frequency range 140 to 1500 Hz and with bulk densities ranging from 4.6 to 67 kg/cu m. When the sound propagated in a direction normal to the fiber alignment, the measured sound absorption showed the occurrence of a strong resonance, which increased absorption above that attributed to viscous and thermal effects. When the sound propagated in a direction parallel to the fiber alignment, indications of strong resonances in the data were not present. The resonance in the data for fibers normal to the direction of sound propagation is attributed to fiber motion. An analytical model was developed for the acoustic behavior of the material displaying the same fiber motion characteristics shown in the measurements.

Dahl, Milo D.↗

NASA NTRS1993

Improvement of the predicted aural detection code ICHIN (I Can Hear It Now)

Acoustic tests were conducted to study the far-field sound pressure levels and aural detection ranges associated with a Sikorsky S-76A helicopter in straight and level flight at various advancing blade tip Mach numbers. The flight altitude was nominally 150 meters above ground level. This paper compares the normalized predicted aural detection distances, based on the measured far-field sound pressure levels, to the normalized measured aural detection distances obtained from sound jury response measurements obtained during the same test. Both unmodified and modified versions of the prediction code ICHIN-6 (I Can Hear It Now) were used to produce the results for this study.

Mueller, Arnold W.↗

NASA NTRS1972

Exploratory investigation of sound pressure level in the wake of an oscillating airfoil in the vicinity of stall

Wind tunnel tests were performed on two oscillating two-dimensional lifting surfaces. The first of these models had an NACA 0012 airfoil section while the second simulated the classical flat plate. Both of these models had a mean angle of attack of 12 degrees while being oscillated in pitch about their midchord with a double amplitude of 6 degrees. Wake surveys of sound pressure level were made over a frequency range from 16 to 32 Hz and at various free stream velocities up to 100 ft/sec. The sound pressure level spectrum indicated significant peaks in sound intensity at the oscillation frequency and its first harmonic near the wake of both models. From a comparison of these data with that of a sound level meter, it is concluded that most of the sound intensity is contained within these peaks and no appreciable peaks occur at higher harmonics. It is concluded that within the wake the sound intensity is largely pseudosound while at one chord length outside the wake, it is largely true vortex sound. For both the airfoil and flat plate the peaks appear to be more strongly dependent upon the airspeed than on the oscillation frequency. Therefore reduced frequency does not appear to be a significant parameter in the generation of wake sound intensity.

Gray, R. B.↗

NASA NTRS1994

Land surface temperature measurements from EOS MODIS data

A generalized split-window method for retrieving land-surface temperature (LST) from AVHRR and MODIS data has been developed. Accurate radiative transfer simulations show that the coefficients in the split-window algorithm for LST must depend on the viewing angle, if we are to achieve a LST accuracy of about 1 K for the whole scan swath range (+/-55.4 deg and +/-55 deg from nadir for AVHRR and MODIS, respectively) and for the ranges of surface temperature and atmospheric conditions over land, which are much wider than those over oceans. We obtain these coefficients from regression analysis of radiative transfer simulations, and we analyze sensitivity and error by using results from systematic radiative transfer simulations over wide ranges of surface temperatures and emissivities, and atmospheric water vapor abundance and temperatures. Simulations indicated that as atmospheric column water vapor increases and viewing angle is larger than 45 deg it is necessary to optimize the split-window method by separating the ranges of the atmospheric column water vapor and lower boundary temperature, and the surface temperature into tractable sub-ranges. The atmospheric lower boundary temperature and (vertical) column water vapor values retrieved from HIRS/2 or MODIS atmospheric sounding channels can be used to determine the range where the optimum coefficients of the split-window method are given. This new LST algorithm not only retrieves LST more accurately but also is less sensitive than viewing-angle independent LST algorithms to the uncertainty in the band emissivities of the land-surface in the split-window and to the instrument noise.

Wan, Zhengming↗

NASA NTRS1938

Drag of cylinders of simple shapes

In order to determine the effect of shape, compressibility, and Reynolds number on the drag and critical speed for simple forms, the drag forces on models of various simple geometric cross sections were measured in the NACA 11-inch high-speed wind tunnel. The models were circular, semitubular, elliptical, square, and triangular (isosceles) cylinders. They were tested over a speed range from 5 percent of the speed of sound to a value in excess of the critical speed, corresponding, for each model, approximately to a tenfold Reynolds number range, which extended from a minimum of 840 for the smallest model to a maximum of 310,000 for the largest model.

Lindsey, W F↗

NASA NTRS1992

Comparison of analysis and experiment for gearbox noise

Low contact ratio spur gears were tested in the NASA gear-noise rig to study the noise radiated from the top of the gearbox. Experimental results were compared with a NASA acoustics code to validate the code for predicting transmission noise. The analytical code is based on the boundary element method (BEM) which models the gearbox top as a plate in an infinite baffle. Narrow band vibration spectra measured at 63 nodes on the gearbox top were used to produce input data for the BEM model. The BEM code predicted the total sound power based on the measured vibration. The measured sound power was obtained from an acoustic intensity scan taken near the surface of the gearbox at the same 63 nodes used for vibration measurement. Analytical and experimental results were compared at four different speeds for sound power at each of the narrow band frequencies over the range of 400 to 3200 Hz. Results are also compared for the sound power level at meshing frequency plus three sideband pairs and at selected gearbox resonant frequencies. The difference between predicted and measure sound power is typically less than 3 dB with the predicted value generally less than the measured value.

Oswald, Fred B.↗

NASA NTRS1972

Application of quasi-linearization techniques to the analysis of aerodynamic-noise fields

The method of parametric differentiation was used as a means of obtaining solutions which describe aerodynamically generated sound fields, and which are valid over an increased range of a specific parameter. Details of applying the method to the problem of calculating the sound field of two rectilinear vortices rotating about an axis between them in a compressible medium are discussed. Pressure distribution in the far field are obtained. Parametric differentiation was also applied to the calculation of aerodynamic sound generated by a rotating cylinder in a viscous, compressible medium. The formulation of this problem in parametric space is given, and a procedure for obtaining a solution is outlined.

Harris, W. L., Sr.↗

NASA NTRS1975

A study of noise source location on a model scale augmentor wing using correlation techniques

An experimental investigation, conducted on a model-scale augmentor wing to identify the sources of far-field noise, is examined. The measurement procedure followed in the investigation involved the cross-correlation of far field sound pressures with fluctuating pressures on the surface of the augmentor flap and shroud. In addition pressures on the surfaces of the augmentor were cross-correlated. The results are interpreted as showing that the surface pressure fluctuations are mainly aerodynamic in character and are convected in the downstream direction with a velocity which is dependent on the jet exhaust velocity. However the far field sound levels in the mid and high frequency ranges are dominated by jet noise. There is an indication that in the low frequency range trailing edge noise, associated with interaction of the jet flow and the flap trailing edge, plays a significant role in the radiated sound field.

Wilby, J. F.↗

NASA NTRS1971

Digital decorrelator saves time and expense in acoustic testing of structures

Instantaneous signals from coherent random sound field are summed and time delayed to avoid introducing vectorial addition errors. Resultant statistically independent signals are applied to spectrometer. Displayed sound pressure level is proportional to square root of sum of squares of sound pressure levels taken over frequency range of interest.

Nakich, R. B.↗

NASA NTRS1971

Soft X-ray astronomy proportional counter electronics

The X-ray multiwire proportional counter is designed to measure cosmic X-ray fluxes at sounding rocket altitudes in the energy range of 0.1 to 10 keV. Four instruments will be launched in a Black Brant 4 rocket employing different combinations of detector windows and gas. The detector is constructed with two layers of twelve cells. A columnator is mounted on the face of one layer whose cells are wired together alternately to form two main detector sections. The electronics and gas regulation systems are mounted on the face of the second layer whose cells are wired together to form one anticoincidence detector section. Normally X-rays will have short ionization paths in only one of the main detector cells at a time and won't enter the anticoincidence detector cells. To distinguish between X-rays and charged particles, the instrument includes a coincidence discriminator, an anticoincidence discriminator, and a pulse rise time discriminator.

Gardner, W. R.↗

NASA NTRS1972

Tables of critical-flow functions and thermodynamic properties for methane and computational procedures for both methane and natural gas

Procedures for calculating the mass flow rate of methane and natural gas through nozzles are given, along with the FORTRAN 4 subroutines used to make these calculations. Three sets of independent variables are permitted in these routines. In addition to the plenum pressure and temperature, the third independent variable is either nozzle exit pressure, Mach number, or temperature. A critical-flow factor that becomes a convenient means for determining the mass flow rate of methane through critical-flow nozzles is tabulated. Other tables are included for nozzle throat velocity and critical pressure, density, and temperature ratios, along with some thermodynamic properties of methane, including compressibility factor, enthalpy, entropy, specific heat, specific-heat ratio, and speed of sound. These tabulations cover a temperature range from 120 to 600 K and pressures to 3 million N/sq m.

Johnson, R. C.↗