SEARCH · Search NASA

Results for “STABILITY, DIRECTIONAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1958

Wind-Tunnel Investigation of Some Effects of Wing Sweep and Horizontal-Tail Height on the Static Stability of an Airplane Model at Transonic Speeds

A research model of an airplane with a configuration suitable for supersonic flight was tested at transonic speeds in order to establish the effects on longitudinal and lateral stability of certain changes in both wing sweep and height of the horizontal tail. Two wings of aspect ratio 3 and taper ratio 0.15, one having the quarter-chord line swept back 30 deg and the other 45 deg, were each tested with the horizontal tail of the model in a low and in a high position. One configuration was also tested with fuselage strakes. The tests were made at Mach numbers from 0.60 to 1.17 and Reynolds numbers from 1.9 x 10(exp 6) to 2.6 x 10(exp 6). The results indicated that a low horizontal-tail position (below the wing-chord plane) gave positive longitudinal stability for the model for all angles of attack used (angles of attack up to 24 deg); whereas, a higher tail position (above the wing-chord plane) resulted in a large reduction in stability at moderate angles of attack. With the higher horizontal tail, the 30 deg-swept-wing model had somewhat more stability than the 45 deg-swept-wing model at subsonic Mach numbers. With the lower tail, the 45 deg-swept-wing model had slightly more stability at all Mach numbers. The model with the 30 deg swept wing had greater directional stability with the tail in the higher rather than the lower position, but the opposite was true for the 45 deg-swept-wing model. The directional stability decreased sharply at high angles of attack; this characteristic was alleviated by the use of fuselage strakes which, however, proved to be detrimental to the longitudinal stability of the model tested.

Fisher, Lewis R.↗

NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

To summarize the significant highlights in this report: (1) Data quality, determined by multiple repeat runs performed on the TCA baseline configuration, and long-term repeatability, determined by comparing baseline Reference H data from this test to a previous test, have been shown to be good. (2) The longitudinal stability of the TCA is more non-linear than for the Reference H, and while it is similar at normal lift values, the TCA has considerably more pitch-up at higher lift. (3) Longitudinal control effectiveness of the TCA is similar to the Reference H and the ratio of elevator effectiveness to horizontal tail effectiveness is approximately 0.3. 4) The directional stability of the TCA is improved relative to Reference H at higher angles-of attack. The chine is effective for improving directional stability. (5) The directional control effectiveness 'of the TCA rudder is the same as that of the Reference H rudder at low angles-of-attack, after taking factors, such as number of rudder panels deflected and vertical tail volume into account. However, rudder effectiveness was shown to be reduced at higher angles-of-attack. (6) The lateral stability was shown to be reduced relative to the Reference H, which may be beneficial at low speeds for alleviating lateral control saturation. (7) Lateral control effectiveness for the TCA was shown to be similar to the Reference H for negative trailing-edge flap deflections and was reduced by approximately 25% for positive trailing-edge flap deflections.

Kubiatko, Paul↗

NASA NTRS1972

Effects of an in-flight thrust reverser on the stability and control characteristics of a single-engine fighter airplane model

The changes in thrust minus drag performance as well as longitudinal and directional stability and control characteristics of a single-engine jet aircraft attributable to an in-flight thrust reverser of the blocker-deflector door type were investigated in a 16-foot transonic wind tunnel. The longitudinal and directional stability data are presented. Test conditions simulated landing approach conditions as well as high speed maneuvering such as may be required for combat or steep descent from high altitude.

Mercer, C. E.↗

NASA NTRS1968

Aerodynamic Characteristics of Several Hypersonic Boost-Glide-Type Configurations at Mach Numbers from 2.30 to 4.63

An investigation has been conducted at Mach numbers from 2.30 to 4.63 to determine the static aerodynamic characteristics of several configurations designed for flight at hypersonic Mach numbers. Two all-wing and three wing-body configurations were tested through an angle-of-attack range from about -4 degrees to 33 degrees and an angle-of-sideslip range from about -4 degrees to 8 degrees at a Reynolds number of 3 times 10 (sup 6) per foot (9.84 times 10 (sup 6) per meter). The results of the investigation indicated that the wing-body configurations produced higher values of maximum lift-drag ratio than those produced by the all-wing models. The high wing-body configurations tend to have a self-trimming capability as opposed to that for the low wing-body configurations. Each of the configurations produced a positive dihedral effect that increased with increasing angle of attack and decreased with increasing Mach number. The high wing-body models produced decreasing values of directional stability with increase in angle of attack, whereas the low wing-body models provided increasing values of directional stability with increase in angle of attack.

Graves, Ernald B.↗

NASA NTRS1958

Wind-Tunnel Investigation of the Low-Speed Characteristics of a 1/8-Scale Model of the Republic XP-91 Airplane with a Vee and a Conventional Tail. Addendum - Characteristics with a Revised Conventional Tail and Drooped Wing Tips

Additional wind-tunnel tests were made of a 1/8-scale model of the Republic XP-91 airplane to determine its characteristics with various modifications. The modifications included a revised conventional tail, revised rocket arrangement, drooped wing tips, and revised landing gear and doors. Tests were also made to determine the effectiveness of the control surfaces of the model with the conventional tail and the effect of changing wing incidence and tail length. The revised rocket arrangement provided a considerable increase in the static directional stability contributed by the vee tail at small angles of yaw. The conventional tail provided a greater static directional stability than the vee tail without increasing the rolling moment due to sideslip. The rolling moment die to sideslip was considerable reduced by either drooped wing tips or open main landing-gear doors. The reduction in rolling moment due to sideslip resulting from the drooped tips was less with the landing-gear doors open than with the doors closed. A change in wing incidence from 0 degrees to 6 degrees reduced the elevator angle required for balance by approximately 6 degrees.

Weiberg, James A.↗

NASA NTRS1977

Aerodynamic characteristics of a 1/6-scale powered model of the rotor systems research aircraft

A wind-tunnel investigation was conducted to determine the effects of the main-rotor wake on the aerodynamic characteristics of the rotor systems research aircraft (RSRA). For the investigation, a 1/6-scale model with a four-blade articulated main rotor was used. Tests were conducted with and without the main rotor. Both the helicopter and the compound helicopter were tested. The latter configuration included the auxiliary thrust engines and the variable-incidence wing. Data were obtained over ranges of angle of attack, angle of sideslip, and main-rotor collective pitch angle at several main-rotor advance ratios. Results are presented for the total loads on the airframe as well as the loads on the rotor, the wing, and the tail. The results indicated that without the effect of the rotor wake, the RSRA had static longitudinal and directional stability and positive effective dihedral. With the effect of the main rotor and its wake, the RSRA exhibited longitudinal instability but retained static directional stability and positive effective dihedral.

Mineck, R. E.↗

NASA NTRS1961

Low-Subsonic-Speed Static Stability of Right-Triangular-Pyramid and Half-Cone Lifting Reentry Configurations

An investigation has been made to determine the low-subsonic-speed static stability characteristics of several right-triangular-pyramid and half-cone configurations. Also studied were the effects of various modifications, such as base extensions, nose shape, nose incidence, and ridge-line shape. The investigation showed that, in general, the models had satisfactory longitudinal and lateral stability. The basic pyramid model and the conical ridge-line model with or without a rounded nose had almost identical longitudinal and lateral stability characteristics and lift-drag ratios. The lift-drag ratios of the cylindrical ridge-line and half-cone models were considerably lower than those of the conical ridge-line model. The addition of a 20 degree boattail to the models increased the lift-drag ratios but decreased the directional stability, whereas a streamwise base extension was more effective in increasing the lift-drag ratios and increased the directional stability.

Ware, George M.↗

NASA NTRS1981

Aerodynamic characteristics of a series of airbreathing missile configurations

The results of an experimental program conducted in order to compile a data base useful in the application of airbreathing propulsion to missiles are presented. The configurations investigated used two-dimensional or axisymmetric twin inlets located at three alternative circumferential positions: 90, 115 and 135 deg to the vertical centerline. The effects of a wing located above the inlets and of various tail configurations were investigated, with a view to longitudinal stability/control and lateral-directional stability characteristics. It is noted that of the three tail configurations tested, the 'X' tail showed (1) the most linear pitch-moment curve, (2) control effectiveness, and (3) positive lateral-directional stability.

Hayes, C.↗

NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

Kubiatko, Paul↗

NASA NTRS1958

Investigation of Control Effectiveness and Stability Characteristics of a Model of a Low-Wing Missile with Interdigitated Tail Surfaces at Mach Numbers of 2.29, 2.97, and 3.51

A brief investigation of the longitudinal stability and control effectiveness at supersonic speeds of a model of a low-wing missile with interdigitated tail surfaces was made in the Langley Unitary Plan wind tunnel. The data were obtained at Mach numbers M of 2.29, 2.97, and 3.51 for Reynolds number (based on the mean geometric chord of the wing) of 1.15 x 10(exp 6), 1.14 x 10(exp 6), and 1.11 x 10(exp 6), respectively. Data were obtained for three settings of the longitudinal control surfaces: with deflection of all surfaces, with deflection of the lower surfaces only, and with all surfaces undeflected. Directional stability data were obtained at M=3.51 for angles of attack of approximately 0 deg and 10 deg. These data, with summary data and typical schlieren photographs, are presented with only a brief analysis. The data indicate that the controls are effective throughout the Mach number range and lift-coefficient range (CL = -0.15 to 0.7, approximately) of the tests. There is a severe break in the pitching-moment curve at M=2.29 which might result in a pitch-up condition in flight, and also a large forward movement of the aerodynamic center with increasing Mach number that produces neutral longitudinal stability at M=3.51 for the moment center used in this investigation. The model was directionally unstable at M=3.51; however, the level of directional stability was about the same for 0 deg and 10 deg angles of attack.

STABILITY AND CONTROL↗

DOE OSTI2025

Propylamine Functionalized Porous Fiber Sorbents with High Oxidation Stability for Direct Air Capture

Amine-based sorbents are highly effective for direct air capture (DAC) due to their excellent CO2 capture efficiency under ultra-dilute conditions. However, these sorbents can suffer degradation when exposed to combinations of heat, oxygen, and other atmospheric components, indicating a need for improved sorbent stability. In this study, we developed amidoxime functionalized polymer of intrinsic microporosity (PIM-1-AO) fibers with tethered amines, specifically tris(2-aminoethyl)amine (TAEA) and tris(3-aminopropyl)amine (TAPA), denoted as PIM-1-AO-TAEA and PIM-1-AO-TAPA, respectively. In addition, large scale sorbent fiber spinning has been successfully performed by producing meters of fibers in the lab. We demonstrated that substituting TAEA with TAPA, which has propyl chains instead of ethyl chains, reduces oxidative degradation under regeneration conditions. The findings revealed that PIM-1-AO-TAPA not only significantly outperforms PIM-1-AO-TAEA after accelerated aging process, but also outperforms any other sorbent used in DAC aged under similar conditions. Moreover, PIM-1-AO-TAPA sorbent fibers showed one of the highest amine efficiencies (0.25) considering the low amine loading (21%) coupled with robust CO2 uptake performance (1.12 mmol/g) under DAC conditions.

amine-based sorbent↗

NASA NTRS1977

Aerodynamic characteristics at Mach 6 of a hypersonic research airplane concept having a 70 deg swept delta wing

The hypersonic aerodynamic characteristics of an air-launched, delta-wing research aircraft concept were investigated at Mach 6. The effect of various components such as nose shape, wing camber, wing location, center vertical tail, wing tip fins, forward delta wing, engine nacelle, and speed brakes was also studied. Tests were conducted with a 0.021 scale model at a Reynolds number, based on model length, of 10.5 million and over an angel of attack range from -4 deg to 20 deg. Results show that most configurations with a center vertical tail have static longitudinal stability at trim, static directional stability at angles of attack up to 12 deg, and static lateral stability throughout the angle of attack range. Configurations with wing tip fins generally have static longitudinal stability at trim, have lateral stability at angles of attack above 8 deg, and are directionally unstable over the angle of attack range.

Clark, L. E.↗

NASA NTRS1954

Measurement of the Static Stability and Control and the Damping Derivatives of a 0.13-Scale Model of the Convair XFY-1 Airplane, TED No. NACA DE 368

An investigation has been conducted to determine the static stability and control and damping in roll and yaw of a 0.13-scale model of the Convair XFY-1 airplane with propellers off from 0 deg to 90 deg angle of attack. The tests showed that a slightly unstable pitch-up tendency occurred simultaneously with a break in the normal-force curve in the angle-of-attack range from about 27 deg to 36 deg. The top vertical tail contributed positive values of static directional stability and effective dihedral up to an angle of attack of about 35 deg. The bottom tail contributed positive values of static directional stability but negative values of effective dihedral throughout the angle-of-attack range. Effectiveness of the control surfaces decreased to very low values at the high angles of attack, The model had positive damping in yaw and damping in roll about the body axes over the angle-of-attack range but the damping in yaw decreased to about zero at 90 deg angle of attack.

Johnson, Joseph L.↗

NASA NTRS1946

Effect of an Auxiliary Belly Fuel Tank on the Low-Speed Static Stability Characteristics of a 1/5-Scale Model of the Grumman XF8F-1 Airplane, TED No. NACA 2384

In.order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a l/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank. It was found that, at low speed, the auxiliary fuel tank test conditions, especially with power on in the landing configuration at high lift coefficients. The static directional stability was decreased for most test conditions, but the addition of a fairing between the fuselage and fuel tank improved the directional stability slightly in the power-on clean condition. The effective dihedral and lateral force were increased for most of the conditions tested. The tuft studies and pressure measurements indicated that the removal of the away braces would improve the.flow characteristics considerably in the region of the fuel tank end might also decrease the buffeting of the belly tank at high speeds.

Cook, Charles B.↗

NASA NTRS1954

Studies of the Lateral-Directional Flying Qualities of a Tandem Helicopter in Forward Flight

An investigation of the lateral-directional flying qualities of a tandem-rotor helicopter in forward flight was undertaken to determine desirable goals for helicopter lateral-directional flying qualities and possible methods of achieving these goals in the tandem-rotor helicopter. Comparison between directional stability as measured in flight and rotor-off model tests in a wind tunnel shows qualitative agreement and, hence, indicates such wind-tunnel test, despite the absence of the rotors, to be one effective method of studying means of improving the directional stability of the tandem helicopter. Flight-test measurements of turns and oscillations, in conjunction with analytical studies, suggest possible practical methods of achieving the goals of satisfactory turn and oscillatory characteristics in the tandem helicopter.

Amer, Kenneth B↗

NASA NTRS1979

Effects of a military cargo pod and tail fins on the aerodynamic characteristics of a large wide-body transport model

Wind tunnel tests were conducted on a 0.03 scale model of a large wide-body commercial aircraft to determine the effects on the static aerodynamic characteristics resulting from the attachment of a belly pod for the long-range deployment of outsize military equipment. The effectiveness of horizontal-tip fins in augmenting directional stability was investigated. At a test Reynolds number of 1.08 x 1,000,000, the addition of the pod results in an increase in total drag of approximately 20 percent. Trim drag due to the pod is very small. Although the pod produces a significant decrease in directional stability, the addition of the tip fins restores some of the stability, particularly at the lower angles of attack.

Jernell, L. S.↗

NASA NTRS1983

Analysis of Nonplanar Wing-tip-mounted Lifting Surfaces on Low-speed Airplanes

Nonplanar wing tip mounted lifting surfaces reduce lift induced drag substantially. Winglets, which are small, nearly vertical, winglike surfaces, are an example of these devices. To achieve reduction in lift induced drag, winglets produce significant side forces. Consequently, these surfaces can seriously affect airplane lateral directional aerodynamic characteristics. Therefore, the effects of nonplanar wing tip mounted surfaces on the lateral directional stability and control of low speed general aviation airplanes were studied. The study consists of a theoretical and an experimental, in flight investigation. The experimental investigation involves flight tests of winglets on an agricultural airplane. Results of these tests demonstrate the significant influence of winglets on airplane lateral directional aerodynamic characteristics. It is shown that good correlations exist between experimental data and theoretically predicted results. In addition, a lifting surface method was used to perform a parametric study of the effects of various winglet parameters on lateral directional stability derivatives of general aviation type wings.

Vandam, C. P.↗

NASA NTRS1957

Investigation at High Subsonic Speeds of the Static Longitudinal and Lateral Stability Characteristics of Two Canard Airplane Configurations

The present investigation was conducted in the Langley high-speed 7-by 10-foot tunnel to determine the static longitudinal and lateral stability characteristics at high subsonic speeds of two canard airplane configurations previously tested at supersonic speeds. The Mach number range of this investigation extended from 0.60 to 0.94 and a maximum angle-of-attack range of -2dewg to 24deg was obtained at the lowest test Mach number. Two wing plan forms of equal area were studied in the present tests; one was a 60deg delta wing and the other was a trapezoid wing having an aspect ratio of 3, taper ratio of 0.143, and an unswept 80-percent-chord line. The canard control had a trapezoidal plan form and its area was approximately 11.5 percent of the wing area. The model also had a low-aspect-ratio highly swept vertical tail and twin ventral fins. The longitudinal control characteristics of the models were consistent with past experience at low speed on canard configurations in that stalling of the canard surface occurred at moderate and high control deflections for moderate values of angle of attack. This stalling could impose appreciable limitations on the maximum trim-lift coefficient attainable. The control effectiveness and maximum value of trim-lift was significantly increased by addition of a body flap having a conical shape and located slightly behind the canard surface on the bottom of the body. Addition of the canard surface at 0deg deflection had relatively little effect on overall directional stability of the delta-wing configuration; however, deflection of the canard surface from 0deg to 10deg had a large favorable effect on directional stability at high angles of attack for both the trapezoid- and delta-wing configurations.

Sleeman, William C., Jr.↗