Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, LATERAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

140 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Impact of coolant temperature on the combustion characteristics and emissions of a stratified-charge direct-injection spark-ignition engine fueled with E30

The direct injection spark ignition (DISI) engine has received considerable attention due to its potential to increase the power density of traditional spark ignition engines while significantly improving fuel economy through lean, unthrottled combustion. However, the market introduction of DISI engines operated in a lean combustion mode is inhibited by their unsatisfactory emissions, especially during cold start conditions that make proper mixture formation more challenging. Ethanol-blended gasoline, now a widely used fuel, makes the cold start of a DISI engine more difficult, leading to higher HC and soot emissions because of the high latent heat of vaporization of ethanol relative to gasoline. This work investigated the impact of coolant temperature on the characteristics of combustion and emissions in a stratified-charge DISI engine fueled with an E30 fuel (i.e. 30% ethanol in gasoline), while the coolant temperature was alternated between four levels (45, 60, 75, and 90 °C) to simulate different conditions throughout the warm-up process. The experiments showed that the coolant temperature affected the post-spark inflammation time, as well as the speed, intensity, and stability of the combustion process in the engine. When the coolant temperature rose, the engine produced more NOX and less CO, PM and HC. In addition, high-speed direct photography was used to obtain crank-angle resolved images of fuel sprays and flames in the cylinder. As the coolant temperature rose, the liquid spray lengths became shorter, reducing the possibility of wall wetting, and reduced irradiance from soot particles also indicated less nonpremixed combustion. The in-cylinder imaging results are consistent with the observed combustion and emission characteristics and shed light on the underlying processes. Finally, some potential solutions to the emissions challenges faced here could be either raising in-cylinder temperatures by using trapped residuals or modifying the injection schedule, for example by increasing the number of injections or to inject later in the cycle into a higher-density environment.

42 ENGINEERING↗
DOE OSTI2022

Demonstrating Advanced Nuclear Energy Solutions for Net Zero

Background/Objectives. The aggressive goals being set by nation states, communities, and private industry for decarbonization of grid electricity, industrial heat sources, and transportation around the world are imperative to mitigating the devastating effects that we are seeing from climate change. Although many of these goals focus on accomplishments by 2035 or 2050, the decisions that we make today won’t just impact the landscape of energy systems for the next 20 or 30 years—they will shape the world’s environment for centuries to come. That means that we can’t just focus on technologies that will get us to 2050, but technologies that will withstand our energy demands over that long-ranging future. Success will require us to utilize all of the clean energy resources that we have available to meet demands for electricity, heat, and steam, and we will need energy carriers such as hydrogen that do not emit additional greenhouse gases at the point of use. Nuclear energy, ranging from technologies in service today to advanced, higher temperature and modular systems that will be in service this decade, will provide a robust complement to renewable energy resources that operate variably. Researchers across the U.S. Department of Energy laboratory complex are working to advance multiple aspects of these clean energy solutions, with many focusing on integrated energy system solutions that leverage all available clean energy assets to meet wide-ranging energy demands. Approach/Activities. Nuclear energy is a proven, zero-emission option during operation that can provide consistent, dispatchable power to meet electricity demands while also providing high-quality heat that can meet energy demands beyond the electricity sector. Energy system design should seek to maximize these assets. As a dispatchable energy source with a small land utilization footprint, nuclear energy can be collocated with renewable resources, and the smaller systems that will be deployed this decade (ranging from a few megawatts to hundreds of megawatts) can be installed right where that energy is needed. Integrated nuclear and renewable systems will enhance power grid reliability and resilience, and they will help stabilize the grid through their increasingly flexible operation. Licensing, installation, and broad adoption of these advanced nuclear energy systems are expected to progress significantly in the 2020s, but this may be longer than desired by some stakeholders wishing to implement impactful clean energy decisions today. However, one must recall that nuclear energy systems will operate for 80 or more years, as is being demonstrated by current fleet nuclear systems. The nuclear community is extremely thorough in reviewing these systems with regard to safety and security; these efforts ensure that the deployed systems will continue to provide reliable, resilient energy over that operational lifetime. That investment of time up front will ensure that we can support energy demands over the centuries to come. While advanced nuclear technologies move through this process, communities and private industry may choose to install renewable generation systems that can later be coupled to the complementary nuclear systems as they become available—thus moving closer to the net zero goals in the near term. Choosing technologies and deployment configurations that allow small modular nuclear powerhouses to be added to these “energy parks” as they become available will ensure that advanced technologies can be readily adopted to support growing demands for clean energy. Results/Lessons Learned. The primary focus of integrated energy systems (IES) research is to assess the technical and economic potential of novel multi-input, multioutput solutions that are expected to enhance energy system flexibility, reliability, and resilience as we pursue a clean energy transition. Various energy applications and product streams beyond electricity are being evaluated, ranging from generation of potable water to production of hydrogen, fertilizers, synthetic fuels, and various chemicals. In early FY23 Idaho National Laboratory (INL) will commission thermal energy generation systems that emulate nuclear fission energy input using electric heating and will allow for integrated system testing with thermal energy storage, hydrogen production via high temperature electrolysis (HTE), and power systems hardware to demonstrate operation of a clean energy park within a microgrid or larger grid infrastructure, supporting up to 450 kW of heat input via electric heating and demonstrating operation of HTE systems at the multi-hundred kW scale. This presentation will highlight the wide array of RD&D being conducted at INL and partner laboratories to develop and deploy nuclear and renewable-based IES that will be key to achieving our net zero goals, including both computational and experimental demonstrations. By working with key collaborators in industry, analytical st

08 HYDROGEN↗
DOE OSTI2023

Ion-driven destabilization of a toroidal electron plasma—A 3D3V PIC simulation

Ion-driven destabilization of a toroidal electron plasma in a small aspect ratio axisymmetric toroidal device is reported for A r + ions of different initial density values using a high fidelity 3D3V PIC solver. Stability of a recently discovered quiescent quasi-steady state (QQS) of a toroidal electron plasma obtained from “seed” solution as a result of entropy extremization at zero inertia is addressed in the presence of a small ion population. An initial value (f0) of the ion fraction (f = n i / n e) and the corresponding secondary electrons are “preloaded” into the system after the electron plasma attains a QQS state. This procedure is regarded as a proxy to the conventional production of ions in the experimental devices via impact ionization. The resulting electron plasma exhibits destabilized “center of charge motion” (m = 1) along with higher order harmonics with dominant power in the second harmonic. Gradual loss of ions (and also electrons) is observed resulting in time varying f values. Beyond a certain value of f0 (≥ 0.005), growth in wall probe current is observed, which saturates at later simulation time due to the loss of particles. In conclusion, trajectories of ion particles indicate ion trapping in the potential well, which is qualitatively similar to the ion resonance instability in pure electron plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Magnetic contributions to corundum-eskolaite and corundum-hematite phase equilibria: A DFT cluster expansion study

Magnetic contributions have the potential to significantly influence predicted phase stability within alloy and mineral mixing phase diagrams, yet have been historically challenging to incorporate due to a significant increase to phase space sampling. Here, in this work, we employ a computational protocol that includes spin orientation as an additional configurational component within multi-component cluster expansions between magnetic and non-magnetic metal oxide alloys [calculated using density functional theory (DFT) and the generalized gradient approximation]. This approach was used to determine the effect of magnetic contributions to corundum-eskolaite and corundum-hematite phase equilibria from first principles. Two-component cluster expansions of the magnetic components of eskolaite and hematite were first performed showing the ability of this method to properly calculate their respective magnetic properties. Two-component cluster expansions were then performed for non-magnetic Al(III) and ferromagnetic Cr(III) and Fe(III), and phase diagrams were calculated for later comparison. Finally, a non-magnetic Al(III) and “up” and “down” magnetic configurations for anti-ferromagnetic Cr(III) and Fe(III) were performed. Magnetic contributions to the calculated phase diagram for the corundumeskolaite system were shown to be inconsequential but are vital for accurate determination of the corundum-hematite solvus.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Impact of inoculation practices on microbiota assembly and community stability in a fabricated ecosystem

Studying plant-microbe-soil interactions is challenging due to their high complexity and variability in natural ecosystems. While fabricated ecosystems provide opportunities to recapitulate aspects of these systems in reduced complexity and controlled environments, inoculation can be a significant source of variation. To tackle this, we evaluated how different bacteria inoculation practices and plant harvesting time points affect the reproducibility of a microbial synthetic community (SynCom) in association with the model grass Brachypodium distachyon. We tested three microbial inoculation practices: seed inoculation, transplant inoculation, and seedling inoculation; and two harvesting points: early (14-day-old plants) and late (21 days post-inoculation). We grew our plants and bacterial strains in sterile devices (EcoFABs) and characterized the microbial community from root, rhizosphere, and sand using 16S ribosomal RNA gene sequencing. The results showed that inoculation practices significantly affected the rhizosphere microbial community only when harvesting at an early time point but not at the late stage. As the SynCom showed a persistent association with B. distachyon at 21 days post-inoculation regardless of inoculation practices, we assessed the reproducibility of each inoculation method and found that transplant inoculation showed the highest reproducibility. Moreover, plant biomass was not adversely affected by transplant inoculation treatment. We concluded that bacteria inoculation while transplanting coupled with a later harvesting time point gives the most reproducible microbial community in the EcoFAB-B. distachyon-SynCom fabricated ecosystem and recommend this method as a standardized protocol for use with fabricated ecosystem experimental systems.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Matrimid substrates with bicontinuous surface and macrovoids in the bulk: A nearly ideal substrate for composite membranes in CO 2 capture

Scalable fabrication of thin-film composite (TFC) membrane for post-combustion carbon capture is often limited by the availability of high-performance nanoporous substrate. Ideally, the substrate should allow for fast gas transport at the selective layer/substrate interface as well as in the bulk of the substrate. In this study, highly permeable Matrimid substrates were prepared via vapor- and nonsolvent-induced phase separations. The phase separation mechanism of the Matrimid®/N-methyl-2-pyrrolidone casting solution was modulated by the addition of LiCl to control the solution thermodynamic stability, and nanoporous Matrimid substrates were formed with a bicontinuous surface and macrovoids in the bulk. This hierarchically optimized structure resulted in a CO 2 permeance of 2.60 × 10 5 GPU (1 GPU = 1 × 10 –6 cm 3 (STP) cm –2 s –1 cmHg –1 = 3.349 × 10 –10 mol m –2 s –1 Pa –1 ), which was ca. 11 times more permeable than a benchmark polyethersulfone substrate with cellular pores. The benefit of using this new substrate was demonstrated by coating a 170-nm amine-containing polymer to form a TFC facilitated transport membrane. The membrane exhibited a CO 2 permeance of 932 GPU at 57°C, which was 72 GPU higher than the counterpart coated on the benchmark substrate. Meanwhile, the CO 2 /N 2 selectivity was remained at 158. This permeance improvement could be well explained by the resistance-in-series model, where the improved permeance was attributed to the reductions in substrate and lateral diffusion mass transfer resistances. The upper bound (UB) analysis indicates that the Matrimid substrate is nearly ideal for the state-of-the-art polymers for CO 2 /N 2 separation. Here, the substrate improvement could also reduce the parasitic energy associated with the membrane process due to the reduced membrane cost and flue gas compression requirement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The Role of the Organic Solvent Polarity in Isolating Uranyl Peroxide Capsule Fragments

Uranyl peroxide capsules are a fascinating class of polyoxometalates (POMs), discovered only in the 21st century. Understanding the reactivity between peroxide, alkali cations, and uranyl in alkaline solutions is important in nuclear science disciplines including mineralogy, nuclear energy, and legacy nuclear wastes. In this work, we have developed a general procedure to isolate different fragments of the uranyl-peroxide POM capsules, using organic solvents to partially remove K + salts from crude solids of the monomer building block UO 2 (O 2 ) 3 4– (K–U 1 ), leading to stabilization of these reactive fragments. Higher polarity organic solvents remove more K + salts from the crude solid, owed to higher solubility, resulting in more extensive linking of uranyl peroxide building units. By this strategy we have isolated and structurally characterized a dimer K 6 [(UO 2 ) 2 (O 2 ) 4 (OH) 2 ]·7H 2 O (K–U 2 ) and a hexamer face frequently observed in the capsules, K 12 [(UO 2 ) 6 (O 2 ) 9 (OH) 6 ]$·x$H 2 O(K–U 6 ). Comparing experimental and computed Raman spectra shows that these intermediates crystallize by a solid-to-solid transformation, via polymerization of the monomer building block. By small-angle X-ray scattering (SAXS), we track the conversion of the fragments to POM capsules; the reaction rate increases from K–U 1 (days) < K–U 2 (hours) < K–U 6 (instantaneous). This study provides a general synthetic procedure to isolate metastable uranyl peroxide oligomers and control the oligomerization, which will be later applied to systems with the heavier alkalis that are even less stable.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Numerical and Physical Simulation of the Fluid Flow in a Beam Blank Mold Fed Through the Center of the Web

Fluid flow inside a beam blank mold fed through a three-port SEN (two lateral ports and one bottom port), positioned at the center of the mold, has been investigated. Literature survey shows that this kind of configuration is not frequently used. It had been shown that it is possible to get a symmetrical flow with this configuration. The downward inclination of the ports should influence the transient fluid flow. The greater the downward inclination, the greater is the instability of the jet and of the interface between the immiscible fluids that simulate the slag/metal behavior. The flow characterization was made by dye dispersion, PIV technique, measurement of the meniscus oscillation using ultrasonic sensors, and CFD simulations. The slag/metal behavior was simulated using water and oils with different physical properties. The results from PIV as well as from observations of the water–oil interface have been used to validate the CFD simulations. Oils with density close to water resulted in more instability at the interface with entrainment starting from fluid flow rate of 125 L/min (equivalent to casting speed of 1 m/min). Decreasing the viscosity of slag (oils) and increasing the casting velocity (water flow rate) result in reduction of the interfacial stability.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development of Anti- Yersinia pestis Human Antibodies with Features Required for Diagnostic and Therapeutic Applications

Yersinia pestis is a category A infective agent that causes bubonic, septicemic, and pneumonic plague. Notably, the acquisition of antimicrobial or multidrug resistance through natural or purposed means qualifies Y. pestis as a potential biothreat agent. Therefore, high-quality antibodies designed for accurate and sensitive Y. pestis diagnostics, and therapeutics potentiating or replacing traditional antibiotics are of utmost need for national security and public health preparedness. Here, we describe a set of human monoclonal immunoglobulins (IgG1s) targeting Y. pestis fraction 1 (F1) antigen, previously derived from in vitro evolution of a phage-display library of single-chain antibodies (scFv). We extensively characterized these antibodies and their effect on bacterial and mammalian cells via: ELISA, flow cytometry, mass spectrometry, spectroscopy, and various metabolic assays. Two of our anti-F1 IgG (αF1Ig 2 and αF1Ig 8) stood out for high production yield, specificity, and stability. These two antibodies were additionally attractive in that they displayed picomolar affinity, did not compete when binding Y. pestis, and retained immunoreactivity upon chemical derivatization. Most importantly, these antibodies detected < 1,000 Y. pestis cells in sandwich ELISA, did not harm respiratory epithelial cells, induced Y. pestis agglutination at low concentration (350 nM), and caused apparent reduction in cell growth when radiolabeled at a nonagglutinating concentration (34 nM). These antibodies are amenable to the development of accurate and sensitive diagnostics and immuno/radioimmunotherapeutics.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

GEN3D Experimental and Numerical Development of GEN3 Durability Models

Understanding of the high temperature durability of particles and the materials that contain them is critical to next generation of concentrating solar power (CSP) technology. Here we studied the durability of particles and their containment materials under extreme UV cycling, thermal cycling, and in low-speed high temperature mechanical wear situations. The optical stability of seven candidate particles has been determined following exposure to the high temperature conditions present in a generation 3 particle-based CSP technology. Particle solar weighted absorptance and emittance measured periodically during 10,000 high solar irradiance exposure cycles and up to 400 hours of isothermal aging has been documented. The particle aging due to repeated exposure to concentrated solar flux represented the 30-year lifetime of a power plant. Models were fit to the absorptivity and emissivity data following the isothermal aging provides the projected optical degradation of the particles as a function of temperature. Mechanical wear was studied through the use of custom developed wear testing facilities for measuring high temperature impact wear, abrasion wear, and particle attrition. Additionally, a novel technique for measuring the high temperature mechanical properties of single particles was developed. Through these tests it was observed that high nickel alloys generally showed lower wear than comparable iron based steels, particularly at elevated temperatures of 800°C. Mechanical wear at these temperatures is a highly complex phenomenon combining both mechanical wear and oxidation. Additionally, the containment materials wear rates are influenced by the particles (both hardness and roundness), making the wear mechanisms complex. The initial wear test conducted in the abrasion test rig revealed a substantial amount of oxide materials in the particle bed after testing (in relative to later tests), and substantially more wear, likely indicating a need for concern in startup operation of particle facilities to not incur high wear from the presence of oxides. Particle attrition experiments have only been conducted for a single material but increase size distribution, reduction in circularity, and particle diameter is observed. Efforts to develop predictive models was limited due to a testing campaign that prioritized testing materials for particle pathway developers over building a comprehensive design of experiments. The results discussed in this report inform future CSP developers and researchers further de risking the technology and assisting in its future development. ParticleBased CSP development provides a path to dispatchable solar power generation with storage at a price competitive in the current energy market. Lowering the cost of CSP technology provides a carbon free power generation solution that can assist in the transition from fossil fuels to renewable sources of electricity.

14 SOLAR ENERGY↗
DOE OSTI2022

A Novel Process for Converting Coal to High-Value Polyurethane Products

Battelle has demonstrated a patented process for making high-value, polyurethane (PU) foam from coal, based on preparing liquefied coal via direct liquefaction, converting it to polyols as an intermediate via ozonation, and then making PU foams from these polyols. This process represents a breakthrough in innovative utilization of U.S. coals, and is applicable to bituminous as well as sub-bituminous coals. The resulting PU foam products are projected to have an extremely high value (i.e., over $\$5,000$ /ton), with nearly 100% of carbon utilization from coalderived liquid feedstock, and 31.5% to 43.5% of the carbon in the PU foam polyol product being bio-based. The targeted products represent an extremely large (i.e., over $80 billion/year), existing PU foam market, which could expand into making coatings and adhesives. The process can further help reduce petroleum imports, while improving the economics of PU foam production. This work was completed with funding from the National Energy Technology Laboratory (NETL), with cost share from the State of Ohio’s Ohio Development Services Agency (ODSA) and others, and has advanced the process to 10 kg/day continuous scale and thus to Technology Readiness Level (TRL) 5. A total of 48 coal-based polyols were prepared and evaluated. The initial 28 polyols focused on range finding for ideal conditions. The later 20 polyols were produced as part of process optimizations. These optimizations were targeted around a continuous ozonolysis process to evaluate extended time reactions and to create the necessary intermediate for production of 1-gallon samples of polyol. The most unique attribute of Battelle’s polyol is in the utilization of coal’s aromaticity to gain final foam rigidity. Typically, polyols depend on the isocyanate fraction and cross-linking to gain rigidity. By utilizing coal, we were able to maintain rigidity while reducing the overall hydroxyl value of the polyol. This is important as lower hydroxyl value leads to greater percent weight of the coal-based polyol because less isocyanate is required for foaming. This leads to greater foam cost savings. This report provides the details, process, and process cost models of the conversion of coal to polyols and further to PU foams. Battelle’s process begins with coal liquids. These liquids can be obtained by two processes: coal coking or pyrolysis to produce coal tar, and Battelle’s biobased coal-to-liquids (CTL) process to produce heavy syncrude after liquifying >85% coal. After liquification, Battelle utilizes ozonolysis to create functionalization on the polyaromatic coal structure. The functionalization is then converted to the final polyester polyol through transesterification, or to hydroxyamide polyol through amidification. Equivalent or better standard properties have been obtained for 2 lb/ft 3 density rigid, water and freon-alternative blown foams, including compressive strength, density, R-value, and dimensional stability. Target applications for these foams are insulation, packaging, and energy-absorbing foams. Some exploratory testing also showed promise for adhesives applications. A detailed economic analysis showed that Battelle’s polyol process is economical, at a 140 metric tons per day (MTD) polyol production scale. An attractive return on investment (ROI) at competitive pricing validates the process is ready for a pilot-plant demonstration. A scale-up plan is provided.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Mineral Protection and Resource Limitations Combine to Explain Profile-Scale Soil Carbon Persistence

The fate of soil carbon (C) is largely controlled by microbial oxidation of organic matter (OM), which is constrained by a variety of mechanisms. OM association with soil minerals provides pronounced protection against microbial decomposition. However, factors such as climate, occlusion, and resource limitations also contribute to OM preservation. Here, we explore the factors explaining C distribution and age within an upland rainforest soil in Hawai'i, a site with abundant preferential flow paths (PFPs) and high short-range order (SRO) mineral content. We characterized lateral and vertical changes in Δ 14 C, SRO mineral content, C-functional group chemistry, and microbial community composition to elucidate the contributions of multiple protection mechanisms to OM preservation. Consistent with our expectation, SRO mineral content and Δ 14 C were strongly correlated (R 2 = 0.95), indicating strong mineral protection of OM throughout the profile. Surprisingly, distance from PFP was also a significant predictor of Δ 14 C and improved model fit, particularly in the shallow horizons (R 2 = 0.97). Elevated C/N ratios, decreased microbial abundance, and greater SRO mineral content suggest nitrogen limitations and enhanced mineral protection constrain OM turnover with distance from PFPs in deep, subsurface mineral horizons. Steady microbial abundance, increasing putative anaerobe abundance, and changes in C-functional group chemistry indicate oxygen limitations constrain OM turnover in the matrix of shallow mineral horizons. Given that oxygen and nutrient limitations contribute to OM preservation in this high SRO system—an exemplar of mineral protection—resource limitations may play an even more important role in OM preservation in other well-structured soils.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Computational and Experimental Investigation of Thermal-Mechanical- Chemical Mechanisms of High-burnup Spent Nuclear Fuel (SNF) Processes at Elevated Temperatures and Degradation Behavior in Geologic Repositories

The overarching goal of the combined computational and experimental R&D activities proposed in this project is to enhance understanding of the mechanisms and thermal-mechanical-chemical (TMC) parameters controlling the instant release fraction (IRF) and matrix dissolution of high-burnup (HB; burnup) spent nuclear fuels (SNFs) and the subsequent formation, stability, and phase transformations of SNF alteration products under long-term storage and geological disposal conditions. Uranium dioxide may undergo oxidative corrosion/alteration, and the IRF may be increased for HB SNF, both of which may affect environmental systems associated with SNF long-term storage and disposal. The oxidative matrix dissolution may form various complex uranyl-based phases, including a rich variety of oxides, silicates, carbonates and other secondary minerals in varied geological environments (e.g., studtite, metastudtite, amorphous uranyl peroxide, uranium trioxide, triuranium octoxide, schoepite, dehydrated schoepite, metaschoepite, becquerelite, soddyite, rutherfordine,...). These uranyl phases generally have higher mobility UO 2 +2 species than less soluble U 4+ phases. However, limited information on the thermodynamic properties and formation kinetics of these uranyl-bearing phases is available to predict explicitly paragenesis under the conditions relevant to long-term storage or disposal. The proposed project draws on complementary expertise and research backgrounds from the team members: (i) to apply a combined ab initio modeling (UNLV/UTEP and SNL) and experimental (UNLV) strategy investigating the high-temperature TMC mechanisms of alteration of SNF under α-radiolysis conditions; (ii) to investigate the mechanistic of phase transformations in UNF degradation products under various conditions expected in long-term storage systems (e.g. (UO 2 )O 2 (H 2 O) 4 → (UO 2 )O 2 (H 2 O) 2 → U 2 O 7 → UO 3 → U 3 O 8 ); (iii) to determine high-accuracy TMC parameters for complex uranyl-based phases formed in storage or geological disposal environments (e.g. UO 3 (H 2 O) 2 , Ca[(UO 2 ) 6 O 4 (OH) 8 ] 8 H 2 O, (UO 2 ) 2 (SiO 4 ) 3 2H 2 O,…). The unforeseen COVID-19 pandemic led to the laboratory/campus closure since March 2020, that resulted in a significant delay in reaching milestones in a satisfactory manner, due to (i) the statewide recommendation from stop-working to later limited work in the lab and work-from-home (WFH), (ii) no in-person interactions, and (iii) a hiring freeze at UNLV. Therefore, a no cost extension (10/01/2021- 9/30/2022) was requested to help make up the time we lost during the global pandemic in 2020-2021, leading to paradigm shifts in the focus of the project in the following three main tasks: Task 1 (Computational), Task 2 (Experimental), and Task 3 (Final report, due on 12/29/2022).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Partitioning of Seven Different Classes of Antibiotics into LPS Monolayers Supports Three Different Permeation Mechanisms through the Outer Bacterial Membrane

The outer membrane (OM) of Gram-negative (G-) bacteria presents a barrier for x classes of antibacterial agents. Lipopolysaccharide (LPS), present in the outer leaflet of the OM, is stabilized by divalent cations and is considered to be the major impediment for antibacterial agent permeation. However, the actual affinities of major antibiotic classes toward LPS have not yet been determined. In the present work, we use Langmuir monolayers formed from E. coli Re and Rd types of LPS to record pressure-area isotherms in the presence of antimicrobial agents. Our observations suggest three general types of interactions. Firstly, some antimicrobials demonstrated no measurable interactions with LPS. This lack of interaction in the case of cefsulodin, a third-generation cephalosporin antibiotic, correlates with its low efficacy against G- bacteria. Ampicillin and ciprofloxacin also show no interactions with LPS, but in contrast to cefsulodin, both exhibit good efficacy against G- bacteria, indicating permeation through common porins. Secondly, we observe substantial intercalation of the more hydrophobic antibiotics novobiocin, rifampicin, azithromycin, and telithromycin into relaxed LPS monolayers. These largely re-partition back to the subphase with monolayer compression. We find that the hydrophobic area, charge, and dipole all show correlations with both the mole fraction of antibiotic retained in the monolayer at the monolayer-bilayer equivalence pressure and the efficacies of these antibiotics against G- bacteria. Thirdly, amine-rich gentamicin and the cationic antimicrobial peptides polymyxin B and colistin show no hydrophobic insertion but are instead strongly driven into the polar LPS layer by electrostatic interactions in a pressure-independent manner. Their intercalation stably increases the area per molecule (by up to 20%), which indicates massive formation of defects in the LPS layer. These defects support a self-promoted permeation mechanism of these antibiotics through the OM, which explains the high efficacy and specificity of these antimicrobials against G- bacteria.

lateral pressure↗