Search NASA⌕ Search

SEARCH · Search NASA

Results for “STALLING - PREVENTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size On the Tip Clearance Flow Structure at Near Stall Operation - Part 2

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Unsteady↗
NASA NTRS1940

Observations in Flight of the Region of Stalled Flow Over the Blades of the Kellett YG-1B Tapered-Blade Autogiro Rotor

In conjunction with a series of tests requested by the Army Air corps on a new set of tapered rotor blades, of NACA 230 series section and built for the Kellett YG-1B autogiro, it was convenient to supplement previous studies of the region or stalled flow on rotors by making photographic observations of the flow over the blades in flight. These observations are described in this report. It is shown that the maximum radius stalled on the new rotor increases more rapidly with tip-speed ratio than was true on the rectangular-blade, Gottingen 606 section rotor previously tested on the same ship, though the increase in importance of the stalled region is not as decisive as consideration of the change in section would suggest. The increased loss in the stalled region is felt to be at least a contributing cause in the failure of the new blades to Increase the top speed of the machine.

Gustafson, Frederic B.↗
NASA NTRSDate not supplied

Stall Margin Improvement in a Transonic Compressor with a Casing Treatment: Flow Mechanism

Effects of casing treatments for improved stall margin in transonic compressors are investigated. Two types of compressor casing treatments, circumferential grooves and axial slots casing treatments, are studied in detail. The primary objective of the current paper is to identify the underlying fluid mechanics that change the stall margin of transonic compressors with these two casing treatments. Large eddy simulation (LES) is applied to calculate the compressor flow fields with these two types of casing treatments. Calculated flow fields are first compared with measured experimental data to validate the LES simulation. Details of the calculated unsteady flow structures are examined to unearth the underlying flow mechanism for the improved stall margin. Further possible design optimization of the casing treatment for the stall margin extension without any performance penalty near the design condition is also explored.

compressor↗
NASA NTRS2016

Stall Recovery Guidance Algorithms Based on Constrained Control Approaches

Aircraft loss-of-control, in particular approach to stall or fully developed stall, is a major factor contributing to aircraft safety risks, which emphasizes the need to develop algorithms that are capable of assisting the pilots to identify the problem and providing guidance to recover the aircraft. In this paper we present several stall recovery guidance algorithms, which are implemented in the background without interfering with flight control system and altering the pilot's actions. They are using input and state constrained control methods to generate guidance signals, which are provided to the pilot in the form of visual cues. It is the pilot's decision to follow these signals. The algorithms are validated in the pilot-in-the loop medium fidelity simulation experiment.

Aircraft stall↗
NASA NTRS2016

Analysis of Low-Speed Stall Aerodynamics of a Business Jets Wing Using STAR-CCM+

Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) analysis was conducted: to study the low-speed stall aerodynamics of a GIII aircrafts swept wing modified with (1) a laminar-flow wing glove, or (2) a seamless flap. The stall aerodynamics of these two different wing configurations were analyzed and compared with the unmodified baseline wing for low-speed flight. The Star-CCM+ polyhedral unstructured CFD code was first validated for wing stall predictions using the wing-body geometry from the First AIAA CFD High-Lift Prediction Workshop.

fluid mechanics↗
NASA NTRS1971

Effect of several porous casing treatments on stall limit and on overall performance of an axial flow compressor rotor

Several geometrically different porous casings were tested with an axial-flow compressor rotor to determine their effects upon the rotor stall-limit line and overall performance. The tests were conducted using both uniform and nonuniform inlet-flow conditions. The rotor performance with the various casing treatments is compared with that obtained with a solid casing. The ability of the various casing treatments to displace the rotor stall-limit line to lower weight flows was observed. Significant stall-margin increases were obtained with several of the porous casings. Peak efficiencies with two of the porous casings were as high as or slightly higher than that obtained with solid casing.

Osborn, W. M.↗
NASA NTRS1974

Study of casing treatment stall margin improvement phenomena

The results of a program of experimental and analytical research in casing treatments over axial compressor rotor blade tips are presented. Circumferential groove, axial-skewed slot, and blade angle slot treatments were tested. These yielded, for reduction in stalling flow and loss in peak efficiency, 5.8% and 0 points, 15.3% and 2.0 points, and 15.0% and 1.2 points, respectively. These values are consistent with other experience. The favorable stalling flow situations correlated well with observations of higher-then-normal surface pressures on the rotor blade pressure surfaces in the tip region, and with increased maximum diffusions on the suction surfaces. Annular wall pressure gradients, especially in the 50-75% chord region, are also increased and blade surface pressure loadings are shifted toward the trailing edge for treated configurations. Rotor blade wakes may be somewhat thinner in the presence of good treatments, particularly under operating conditions close to the baseline stall.

Prince, D. C., Jr.↗
NASA NTRS1974

Dynamic stall modeling and correlation with experimental data on airfoils and rotors

Two methods for modeling dynamic stall have been developed. The alpha, A, B method generates lift and pitching moments as functions of angle of attack and its first two time derivatives. The coefficients are derived from experimental data for oscillating airfoils. The Time Delay Method generates the coefficients from steady state airfoil characteristics and an associated time delay in stall beyond the steady state stall angle. Correlation with three types of test data shows that the alpha, A, B method is somewhat better for use in predicting helicopter rotor response in forward flight. Correlation with lift and moment hysteresis loops generated for oscillating airfoils was good for both models.

Carlson, R. G.↗
NASA NTRS1974

Comparison of three methods for calculation of helicopter rotor blade loading and stresses due to stall

A comparison is made of the results of three methods for calculating the effects of dynamic stall on the performance, airloads, and blade stresses of a helicopter rotor at high loading. The three dynamic-stall methods considered predict essentially the same performance and trim for the rotor. They give roughly the same mean bending moments, but the peak-to-peak torsion and bending moments differ by 25 to 40 percent, and there are differences in the details of the predicted blade motion and stresses. The latter are due to significant differences in the dynamic stall aerodynamic loads, particularly the aerodynamic pitch moment, predicted by the three methods.

Johnson, W.↗
NASA NTRS1974

Investigation of rotor blade element airloads for a teetering rotor in the blade stall regime

A model of a teetering rotor was tested in a low speed wind tunnel. Blade element airloads measured on an articulated model rotor were compared with the teetering rotor and showed that the teetering rotor is subjected to less extensive flow separation. Retreating blade stall was studied. Results show that stall, under the influence of unsteady aerodynamic effects, consists of four separate stall events, each associated with a vortex shed from the leading edge and sweeping over the upper surface of the rotor blade. Current rotor performance prediction methodology was evaluated through computer simulation.

Dadone, L. U.↗
NASA NTRS1975

Further studies of stall flutter and nonlinear divergence of two-dimensional wings

An experimental investigation is made of the purely torsional stall flutter of a two-dimensional wing pivoted about the midchord, and also of the bending-torsion stall flutter of a two-dimensional wing pivoted about the quarterchord. For the purely torsional flutter case, large amplitude limit cycles ranging from + or - 11 to + or - 160 degrees were observed. Nondimensional harmonic coefficients were extracted from the free transient vibration tests for amplitudes up to 80 degrees. Reasonable nondimensional correlation was obtained for several wing configurations. For the bending-torsion flutter case, large amplitude coupled limit cycles were observed with torsional amplitudes as large as + or - 40 degrees. The torsion amplitudes first increased, then decreased with increasing velocity. Additionally, a small amplitude, predominantly torsional flutter was observed when the static equilibrium angle was near the stall angle.

Dugundji, J.↗
NASA NTRS1978

Dynamic stall experiments on the NACA 0012 airfoil

The flow over a NACA 0012 airfoil undergoing large oscillations in pitch was experimentally studied at a Reynolds number of and over a range of frequencies and amplitudes. Hot-wire probes and surface-pressure transducers were used to clarify the role of the laminar separation bubble, to delineate the growth and shedding of the stall vortex, and to quantify the resultant aerodynamic loads. In addition to the pressure distributions and normal force and pitching moment data that have often been obtained in previous investigations, estimates of the unsteady drag force during dynamic stall have been derived from the surface pressure measurements. Special characteristics of the pressure response, which are symptomatic of the occurrence and relative severity of moment stall, have also been examined.

Mcalister, K. W.↗
NASA NTRS1980

The effects of leading edge modifications on the post-stall characteristics of wings

An investigation of the effects of leading edge modifications on the post-stall characteristics of two rectangular planform wings in a series of low speed wind tunnel tests is presented. Abrupt discontinuities in the leading edge shape of the wings were produced by placing a nose glove over a portion of the span or by deflecting sections of a segmented leading edge flap. Six component balance data, oil flow visualization photographs, and pressure distribution measurements were obtained, and tests made to study the development of flow separation at stall on small scale planform wing models. Results of oil flow visualization tests at and beyond stall showed the formation of counter-rotating swirl patterns on the upper surface of the '2-D' and '3-D' wings, and results of a numerical lifting line technique applied to wings with leading edge modifications are included.

Winkelmann, A. E.↗
NASA NTRS1981

Fluid mechanics mechanisms in the stall process of helicopters

Recent experimental results from airfoils in the Mach number, Reynolds number, or reduced frequency ranges typical of helicopter rotor blades have identified the most influential flow mechanisms in the dynamic stall process. The importance of secondary shed vortices, downstream wake action, and the flow in the separated region is generally acknowledged but poorly understood. By means of surface pressure cross-correlations and flow field measurements in static stall, several new hypotheses have been generated. It is proposed that vortex shedding may be caused by acoustic disturbances propagating forward in the lower (pressure) surface boundary layer, that wake closure is a misnomer, and that the shed vortex leaves a trail of vorticity that forms a turbulent free shear layer. The known dynamic stall flow mechanisms are reviewed and the potential importance of recently proposed and hypothetical flow phenomena with respect to helicopter blade aeroelastic response are assessed.

Young, W. H., Jr.↗
NASA NTRS1981

Fluid mechanics mechanisms in the stall process of airfoils for helicopters

Phenomena that control the flow during the stall portion of a dynamic stall cycle are analyzed, and their effect on blade motion is outlined. Four mechanisms by which dynamic stall may be initiated are identified: (1) bursting of the separation bubble, (2) flow reversal in the turbulent boundary layer on the airfoil upper surface, (3) shock wave-boundary layer interaction behind the airfoil crest, and (4) acoustic wave propagation below the airfoil. The fluid mechanics that contribute to the identified flow phenomena are summarized, and the usefulness of a model that incorporates the required fluid mechanics mechanisms is discussed.

Young, W. H., Jr.↗
NASA NTRS1982

Application of an airfoil stall flutter computer prediction program to a three-dimensional wing: Prediction versus experiment

An aerodynamic computer code, capable of predicting unsteady and C sub m values for an airfoil undergoing dynamic stall, is used to predict the amplitudes and frequencies of a wing undergoing torsional stall flutter. The code, developed at United Technologies Research Corporation (UTRC), is an empirical prediction method designed to yield unsteady values of normal force and moment, given the airfoil's static coefficient characteristics and the unsteady aerodynamic values, alpha, A and B. In this experiment, conducted in the PSU 4' x 5' subsonic wind tunnel, the wing's elastic axis, torsional spring constant and initial angle of attack are varied, and the oscillation amplitudes and frequencies of the wing, while undergoing torsional stall flutter, are recorded. These experimental values show only fair comparisons with the predicted responses. Predictions tend to be good at low velocities and rather poor at higher velocities.

Muffoletto, A. J.↗
NASA NTRS1982

An experimental study of mushroom shaped stall cells

Surface patterns characterized by a pair of counter-rotating swirls have been observed in connection with the conduction of surface flow visualization experiments involving test geometries with separated flows. An example of this phenomenon occurring on a finite wing with trailing edge stall has been referred to by Winkelmann and Barlow (1980) as 'mushroom shaped'. A description is presented of a collection of experimental results which show or suggest the occurrence of mushroom shaped stall cells on a variety of test geometries. Investigations conducted with finite wings, airfoil models, and flat plates are considered, and attention is given to studies involving the use of bluff models, investigations of shock induced boundary layer separation, and mushroom shaped patterns observed in a number of miscellaneous cases. It is concluded that the mushroom shaped stall cell appears commonly in separated flow regions.

Winkelmann, A. E.↗
NASA NTRS1982

Transient phenomena of shock-induced turbulent separation for a spikebody and stalling airfoil at transonic and supersonic speeds

The time-dependent, compressible, Reynolds-averaged, full Navier-Stokes equations are applied to solve an axisymmetric flow around a forward-facing stepbody (spikebody) at supersonic speeds and a stalling airfoil at transonic speeds. Important transient and unsteady phenomena, not yet well understood, are examined, and significant new findings of the present solution to the phenomena are discussed. The phenomena described in detail are as follows: The evolution of the shock wave pressure built up by the impact of the pressure waves, one from the trailing edge; the separation of the flow as influenced by the shock wave; the location of the reversed flow, the separation point, and the reattachment point; and the transient (or unsteady) phenomena of the flow pulsation, oscillation, and stalling of the body and airfoil wake flow. The numerical results show that the transient flow instability is caused by a supersonic jet induced in the separation bubble by the shock-bifurcation (lambda shock) mechanism between the separation shock and the reflected shock. Pulsation and stall phenomena are caused by a sudden increase in the leading-edge pressure due to the jet and the separation bubble interacting along the stagnation point flow.

Yoshikawa, K. K.↗