Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS-STRAIN DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

143 records · Page 8

(Project 14-6770) An Investigation to Establish Multiphysical Property Dataset of Nuclear Materials Based on in-situ Observations and Measurements

In-core nuclear materials including fuel pins and cladding materials fail due to issues including corrosion, mechanical wear, and pellet cladding interaction. In most such scenario microstructure dependent and corrosioninduced chemistry dependent property changes significantly affect performance of cladding, pellet, and housing. Emphasis of this work was on replace conventional pellet-cladding material models with a new straingradient viscoplasticity model that is informed by transmission electron microscopy (TEM) based measurements and by nanomechanical Raman spectroscopy (NMRS) based measurements. The TEM measurements are quantitative in nature and therefore reveal stress-strain relations with simultaneous insights into mechanisms of deformation at nanoscale. The NMRS measurements reveal the similar information at mesoscale along with additional information on relating local microstructural stresses with applied stresses. The resulting information is used to fit constants in the strain gradient viscoplasticity model as well as to validate one. During TEM measurements, a micro-electro-mechanical system based setup was developed with mechanical actuation, sensing, heating, and electrical loading. Contrary to post-mortem analysis or qualitative visualization, this setup combines direct visualization of the mechanisms behind deformation with measurement of stress, strain, thermal and electrical properties. The unique research philosophy of visualizing the microstructure at high resolution while measuring the properties led to fundamental understanding in grain size and temperature effects on measured mechanical properties such as fracture toughness. A key contribution is the role of mechanical loading boundary conditions to deconvolute the insitu TEM based nanoscale and NMRS based mesoscale data to bulk behavior. First the literature based pellet cladding mechanical interaction model based on the work of Retel’s and Williamson’s in literature work to predict tempurature and stress distribution in cladding and pellet at normal operating condition was analyzed. Later the data was fitted to find constants for a viscoplastic strain gradient model. The developed model still needs to be refined and calibrated using various experimental results. That remains the focus of future work. Overall, a major thrust of the work was therefore on active control of the microstructure (grain size, defect density and types) exploiting the multi-physics coupling in materials. In particular, using experiments the synergy of current density, mechanical stress and temperature were studied to annihilate defects and recrystallize grains. The developed model is being examined for implementation in BISON. Multiple invited talks, international journal publications, and conference publications were performed by students supported on this work. Another output is support multiple PhD and masters thesis students who will be an important asset for future basic nuclear research. Future Work Recommendations: A nuclear reactor operates under significant variations of thermal loads due to energy cycling and mechanical loads due to constraint effects. Significant thermal and chemical diffusion takes place at the pallet-cladding level. While the proposed work established new experimental approach and new dataset for Zircaloy-4, the irradiation level was in the range of 1-2 dpa. Samples with higher dpa need to be examined. Therefore, a continual of support of the performed work is essential. Currently, these are the only experiments that can measure the produced data. The work also needs to be extended to different fuel types and cladding types such as SiC and FeCrAl based claddings. A combination of datasets for these materials can then be used to analyze accurately predict behavior of critical pellet cladding systems in accident scenario with high heat flux and high thermal loads. This is a BIG unknown as if now.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGC-1 Sister Specimen Testing Data Report

The AGC-1 irradiation capsule will provide irradiation creep design data and data for the effects of irradiation creep on key physical properties of several candidate graphites for the Next Generation Nuclear Plant (NGNP). A further objective of the AGC-1 creep capsule is to provide design data for the effects of neutron irradiation on the properties of a range of NGNP candidate graphites, Characterization, both non-destructively and destructively, of AGC-1 graphite creep “sister” specimens for the major grades, i.e., NBG-17, NBG-18, H-451, PCEA, IG-110, and IG-430 has been performed and is reported here. The properties measured were: bulk density by mensuration and Hg-immersion; tensile properties, including strength, stress-strain behavior, static Young’s modulus, and strain to failure; compressive properties, including strength, stress-strain behavior, static elastic modulus, and strain to failure; elastic constants, including dynamic Young’s modulus (fundamental frequency method), and sonic elastic constants, including Young’s modulus, shear modulus, and Poisson’s ratio; pore size distribution (by Hg-intrusion); crystal structure (by x-ray diffraction, XRD); specific heat (elevated temperature), and thermal conductivity (elevated temperature). Significant differences were noted in the physical properties between the grades examined and are attributed to factors such as density, structure (filler particle size and pore size) and the forming method. Some difficulties were encountered with mechanical testing of small (sub-standard) size specimens due to volume and grain size-section size effects. These difficulties are well understood and are an inevitable consequence of conducting property evaluations on small irradiation specimens. These data are judged to be sufficient to yield adequate fractional change in properties when combined with post-irradiation characterization data. However, the complication associated with small specimen testing reinforces the need to conduct full characterization programs to establish the baseline design properties of the NGNP candidate graphites. A sufficient body of experimental data has been acquired from the AGC-1 creep “sister” specimens to fully characterize the properties of interest for the major grades included in the AGC-1 capsule. These data, in combination with the pre-irradiation characterization data packages for the actual AGC-1 creep and control specimens, provide a sound and sufficient pre-irradiation data set for determination of the effects of irradiation induced dimensional change and creep strain on the physical properties of the nuclear graphite grades in the AGC-1 capsule.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Analysis of bonded joints

A refined elastic analysis of bonded joints which accounts for transverse shear deformation and transverse normal stress was developed to obtain the stresses and displacements in the adherends and in the bond. The displacements were expanded in terms of polynomials in the thicknesswise coordinate; the coefficients of these polynomials were functions of the axial coordinate. The stress distribution was obtained in terms of these coefficients by using strain-displacement and stress-strain relations. The governing differential equations were obtained by integrating the equations of equilibrium, and were solved. The boundary conditions (interface or support) were satisfied to complete the analysis. Single-lap, flush, and double-lap joints were analyzed, along with the effects of adhesive properties, plate thicknesses, material properties, and plate taper on maximum peel and shear stresses in the bond. The results obtained by using the thin-beam analysis available in the literature were compared with the results obtained by using the refined analysis. In general, thin-beam analysis yielded reasonably accurate results, but in certain cases the errors were high. Numerical investigations showed that the maximum peel and shear stresses in the bond can be reduced by (1) using a combination of flexible and stiff bonds, (2) using stiffer lap plates, and (3) tapering the plates.

Srinivas, S.↗

On the thermoelastic analysis of solar cell arrays and related material properties

Accurate prediction of failure of solar cell arrays requires accuracy in the computation of thermally induced stresses. This was accomplished by using the finite element technique. Improved procedures for stress calculation were introduced together with failure criteria capable of describing a wide range of ductile and brittle material behavior. The stress distribution and associated failure mechanisms in the N-interconnect junction of two solar cell designs were then studied. In such stress and failure analysis, it is essential to know the thermomechanical properties of the materials involved. Measurements were made of properties of materials suitable for the design of lightweight arrays: microsheet-0211 glass material for the solar cell filter, and Kapton-H, Kapton F, Teflon, Tedlar, and Mica Ply PG-402 for lightweight substrates. The temperature-dependence of the thermal coefficient of expansion for these materials was determined together with other properties such as the elastic moduli, Poisson's ratio, and the stress-strain behavior up to failure.

Salama, M. A.↗

Damage and failure mechanisms of continuous glass fiber reinforced polyphenylene sulfide

The damage that accompanies flexural deformation of a unidirectional glass fiber composite of polyphenylene sulfide was examined by AE and SEM. These complementary techniques were used to identify damage mechanisms at the microscale and correlate them with the macroscopic stress state in four-point bending. The flexural stress-strain curve was nominally linear to about 1.0 percent strain, but the onset of damage detectable by AE occurred at 0.3 percent strain. Two peaks in the AE amplitude distribution were observed at 35 dB and 60 dB. Low-amplitude events were detected along the entire length of the specimen, and correlation with direct observations of damage made by deforming the composite on the SEM stage suggested that these events arose from matrix cracking and fiber debonding concentrated at flaws on the composite. High amplitude events occurred primarily in the region of highest flexural stress between the inner loading points. They were attributed to fracture of glass fibers on the tension side and surface damage on the compressive side.

Chen, F.↗

Compressive Tests of a Monocoque Box

A monocoque box specimen of aluminum alloy was subjected to end compression and the strains in the stringers were measured up to loads at which permanent set became noticeable. The stringer strains at low loads agreed closely with those computed from the assumption of uniform stress distribution. Buckling of the 0.026-inch sheet between stringers and of the 0.075-inch shear web took place at stresses in accord with theoretical values. Permanent set became noticeable at a load of 115,200 pounds, corresponding to an average stringer stress of about 16,000 pounds per square inch. The measured average strain above the first buckling load was within 2 percent of the theoretical strain as calculated from the dimensions of the box and effective width formulas due to Marguerre and to Cox.

BOXES, MONOCOQUE - STRENGTH, COMPRESSIVE↗

Characterization of Metal Matrix Composites

Experimental methods were developed, adapted, and applied to the characterization of a metal matrix composite system, namely, silicon carbide/aluminim (SCS-2/6061 Al), and its constituents. The silicon carbide fiber was characterized by determining its modulus, strength, and coefficient of thermal expansion. The aluminum matrix was characterized thermomechanically up to 399 C (750 F) at two strain rates. The unidirectional SiC/Al composite was characterized mechanically under longitudinal, transverse, and in-plane shear loading up to 399 C (750 F). Isothermal and non-isothermal creep behavior was also measured. The applicability of a proposed set of multifactor thermoviscoplastic nonlinear constitutive relations and a computer code was investigated. Agreement between predictions and experimental results was shown in a few cases. The elastoplastic thermomechanical behavior of the composite was also described by a number of new analytical models developed or adapted for the material system studied. These models include the rule of mixtures, composite cylinder model with various thermoelastoplastic analyses and a model based on average field theory. In most cases satisfactory agreement was demonstrated between analytical predictions and experimental results for the cases of stress-strain behavior and thermal deformation behavior at different temperatures. In addition, some models yielded detailed three-dimensional stress distributions in the constituents within the composite.

Daniel, I. M.↗

Mechanical Properties of Shock-Damaged Rocks

Stress-strain tests were performed both on shock-damaged gabbro and limestone. The effective Young's modulus decreases with increasing initial damage parameter value, and an apparent work-softening process occurs prior to failure. To further characterize shock-induced microcracks, the longitudinal elastic wave velocity behavior of shock-damaged gabbro in the direction of compression up to failure was measured using an acoustic transmission technique under uniaxial loading. A dramatic increase in velocity was observed for the static compressive stress range of 0-50 MPa. Above that stress range, the velocity behavior of lightly damaged (D(sub 0) less than 0.1) gabbro is almost equal to unshocked gabbro. The failure strength of heavily-damaged (D(sub 0) greater than 0.1) gabbro is approx. 100-150 MPa, much lower than that of lightly damaged and unshocked gabbros (approx. 230-260 MPa). Following Nur's theory, the crack shape distribution was analyzed. The shock-induced cracks in gabbro appear to be largely thin penny-shaped cracks with c/a values below 5 x 10(exp -4). Moreover, the applicability of Ashby and Sammis's theory relating failure strength and damage parameter of shock-damaged rocks was examined and was found to yield a good estimate of the relation of shock-induced deficit in elastic modulus with the deficit in compressive strength.

He, Hongliang↗

Manifestations of Dynamic Strain Aging in Soft-Oriented NiAl Single Crystals

The tensile and compressive properties of six NiAl-base single-crystal alloys have been investigated at temperatures between 77 and 1200 K. The normalized critical resolved shear stresses (CRSS/E) and work-hardening rates (Theta/E) for these alloys generally decreased with increasing temperature. However, anomalous peaks or plateaus for these properties were observed in conventional purity (CPNiAl), Si-doped (NiAl-Si), C-doped low Si (UF-NiAl1), and Mo-doped (NiAl-Mo) alloys at intermediate temperatures (600 to 1000 K). This anomalous behavior was not observed in high-purity, low interstitial material (HP-NiAl). Low or negative strain-rate sensitivities (SRS) also were observed in all six alloys in this intermediate temperature range. Coincident with the occurrence of negative strain-rate sensitivities was the observation of serrated stress-strain curves in the CPNiAl and NiAl-Si alloys. These phenomena have been attributed to dynamic strain aging (DSA). Chemical analysis of the alloys used in this study suggests that the main specie responsible for strain aging in NiAl is C but indicate that residual Si impurities can enhance the strain aging effects. The corresponding dislocation microstructures at low temperatures (300 to 600 K) were composed of well-defined cells. At intermediate temperatures (600 to 900 K), either poorly defined cells or coarse bands of localized slip, reminiscent of the vein structures observed in low-cycle fatigue specimens deformed in the DSA regime, were observed in conventional purity, Si-doped, and in Mo-doped alloys. In contrast, a well-defined cell structure persisted in the low interstitial, high-purity alloy. At elevated temperatures (greater than or equal to 1000 K), more uniformly distributed dislocations and sub-boundaries were observed in all alloys. These observations are consistent with the occurrence of DSA in NiAl single-crystal alloys at intermediate temperatures.

Weaver, M. L.↗

Notch Sensitivity of Woven Ceramic Matrix Composites Under Tensile Loading: An Experimental, Analytical, and Finite Element Study

The stress concentrations associated with circular notches and subjected to uniform tensile loading in woven ceramic matrix composites (CMCs) have been investigated for high-efficient turbine engine applications. The CMC's were composed of Nicalon silicon carbide woven fabric in SiNC matrix manufactured through polymer impregnation process (PIP). Several combinations of hole diameter/plate width ratios and ply orientations were considered in this study. In the first part, the stress concentrations were calculated measuring strain distributions surrounding the hole using strain gages at different locations of the specimens during the initial portion of the stress-strain curve before any microdamage developed. The stress concentration was also calculated analytically using Lekhnitskii's solution for orthotropic plates. A finite-width correction factor for anisotropic and orthotropic composite plate was considered. The stress distributions surrounding the circular hole of a CMC's plate were further studied using finite element analysis. Both solid and shell elements were considered. The experimental results were compared with both the analytical and finite element solutions. Extensive optical and scanning electron microscopic examinations were carried out for identifying the fracture behavior and failure mechanisms of both the notched and notched specimens. The stress concentration factors (SCF) determined by analytical method overpredicted the experimental results. But the numerical solution underpredicted the experimental SCF. Stress concentration factors are shown to increase with enlarged hole size and the effects of ply orientations on stress concentration factors are observed to be negligible. In all the cases, the crack initiated at the notch edge and propagated along the width towards the edge of the specimens.

Haque, A.↗

High-Fidelity Generalization Method of Cells for Inelastic Periodic Multiphase Materials

An extension of a recently-developed linear thermoelastic theory for multiphase periodic materials is presented which admits inelastic behavior of the constituent phases. The extended theory is capable of accurately estimating both the effective inelastic response of a periodic multiphase composite and the local stress and strain fields in the individual phases. The model is presently limited to materials characterized by constituent phases that are continuous in one direction, but arbitrarily distributed within the repeating unit cell which characterizes the material's periodic microstructure. The model's analytical framework is based on the homogenization technique for periodic media, but the method of solution for the local displacement and stress fields borrows concepts previously employed by the authors in constructing the higher-order theory for functionally graded materials, in contrast with the standard finite-element solution method typically used in conjunction with the homogenization technique. The present approach produces a closed-form macroscopic constitutive equation for a periodic multiphase material valid for both uniaxial and multiaxial loading. The model's predictive accuracy in generating both the effective inelastic stress-strain response and the local stress said inelastic strain fields is demonstrated by comparison with the results of an analytical inelastic solution for the axisymmetric and axial shear response of a unidirectional composite based on the concentric cylinder model, and with finite-element results for transverse loading.

Aboudi, Jacob↗

Matrix Cracking in Four Different 2D SiC/SiC Composite Systems

Silicon carbide fiber reinforced, silicon carbide matrix composites are some of the most advanced composite systems for high-temperature, high-stress applications in oxidizing environments. A basic area that needs to be understood for the purpose of material behavior modeling and optimization is the architectural, constituent, and mechanistic factors that contribute to non-linear stress-strain behavior. The mechanism that causes non-linear stress-strain in dense-matrix composites is the formation and propagation of bridged matrix cracks. In addition, the occurrence and propagation of matrix cracks controls the time-dependent strength-properties of these materials in oxidizing environments at elevated temperatures. A modal acoustic emission technique has been used to monitor and estimate the stress-dependent matrix cracking. Two different SiC matrix systems, chemical vapor infiltrated (CVI) and melt-infiltrated (MI), with two different SiC fiber reinforcement, Hi-Nicalon (trademark) and Sylramic (trademark) were compared. Even though the averages of the range where matrix cracking occurred for the composites varied by more than 0.1% in strain and almost 200 MPa in stress, the range or distribution for matrix cracking could be reduced to a narrow band of stress for CVI SiC and MI SiC composites if it were assumed that all matrix cracks emanate outside of the load-bearing fiber, interphase, CVI preform minicomposite. A simple relationship was determined to describe stress-dependent matrix cracking which can then be used to estimate the onset of large, bridged matrix cracks or for material behavior models.

Morscher, Gregory N.↗

In-Plane Cracking Behavior and Ultimate Strength for 2D Woven and Braided Melt-Infiltrated SiC/SiC Composites Tensile Loaded in Off-Axis Fiber Directions

The tensile mechanical properties of ceramic matrix composites (CMC) in directions off the primary axes of the reinforcing fibers are important for architectural design of CMC components that are subjected to multi-axial stress states. In this study, 2D-woven melt-infiltrated (MI) SiC/SiC composite panels with balanced fiber content in the 0 degree and 90 degree directions were tensile loaded in-plane in the 0 degree direction and at 45 degree to this direction. In addition, a 2D triaxially-braided MI composite panel with balanced fiber content in the plus or minus 67 degree bias directions and reduced fiber content in the axial direction was tensile loaded perpendicular to the axial direction tows (i.e., 23 degrees from the bias fibers). Stress-strain behavior, acoustic emission, and optical microscopy were used to quantify stress-dependent matrix cracking and ultimate strength in the panels. It was observed that both off-axis loaded panels displayed higher composite onset stresses for through-thickness matrix cracking than the 2D-woven 0/90 panels loaded in the primary 0 degree direction. These improvements for off-axis cracking strength can in part be attributed to higher effective fiber fractions in the loading direction, which in turn reduces internal stresses on critical matrix flaws for a given composite stress. Also for the 0/90 panel loaded in the 45 degree direction, an improved distribution of matrix flaws existed due to the absence of fiber tows perpendicular to the loading direction. In addition, for the +67/0/-67 braided panel, the axial tows perpendicular to the loading direction were not only low in volume fraction, but were also were well separated from one another. Both off-axis oriented panels also showed relatively good ultimate tensile strength when compared to other off-axis oriented composites in the literature, both on an absolute strength basis as well as when normalized by the average fiber strength within the composites. Initial implications are discussed for constituent and architecture design to improve the directional cracking of SiC/SiC CMC components with MI matrices.

Morscher, Gregory N.↗

Grain Size-Dependent Crystal Plasticity Constitutive Model for Polycrystal Materials

A new method to introduce grain size-dependence in classical crystal plasticity constitutive model is developed by considering the resistance to dislocation motion in the grain boundary influence region as equivalent to that of a work hardening. A general framework for the size-dependent constitutive model is derived by implementing this method on a core and mantle model. The work hardening, equivalent to grain boundary effect, is realized by introducing a fictitious, pre-existing, plastic strain grain boundary influence region (mantle) following the principles of classical crystal plasticity. This fictitious plastic strain, in effect, increases the yield strength and decreases the initial hardening coefficient of the grain. With the thickness of grain boundary influence region and the distribution of introduced plastic strain remaining the same, the grain boundary effect increased as the grain size becomes smaller. A simplified model that considers the grain boundary effect on a grain average sense is also developed under this general framework. Implementation of this general framework to the specific cases of crystal plasticity constitutive models is demonstrated by considering the case of power law flow rule and hyperbolic-secant hardening rule. Finally, the grain size-dependent constitutive model is validated by comparing the predicted stress-strain behavior of polycrystal samples with different average grain sizes under uniaxial loading with the experimental results.

Grain Size↗

EVALUATION OF U10MO FUEL PLATE IRRADIATION BEHAVIOR VIA NUMERICAL AND EXPERIMENTAL BENCHMARKING

This article analyzes dimensional changes due to irradiation of monolithic plate-type nuclear fuel and compares results with finite element analysis of the plates during fabrication and irradiation. Monolithic fuel plates tested in the Advanced Test Reactor (ATR) at Idaho National Lab (INL) are being used to benchmark proposed fuel performance for several high power research reactors. Post-irradiation metallographic images of plates sectioned at the midpoint were analyzed to determine dimensional changes of the fuel and the cladding response. A constitutive model of the fabrication process and irradiation behavior of the tested plates was developed using the general purpose commercial finite element analysis package, Abaqus. Using calculated burn-up profiles of irradiated plates to model the power distribution and including irradiation behaviors such as swelling and irradiation enhanced creep, model simulations allow analysis of plate parameters that are either impossible or infeasible in an experimental setting. The development and progression of fabrication induced stress concentrations at the plate edges was of primary interest, as these locations have a unique stress profile during irradiation. Additionally, comparison between 2D and 3D models was performed to optimize analysis methodology. In particular, the ability of 2D and 3D models account for out of plane stresses which result in 3-dimensional creep behavior that is a product of these components. Results show that assumptions made in 2D models for the out-of-plane stresses and strains cannot capture the 3-dimensional physics accurately and thus 2D approximations are not computationally accurate. Stress-strain fields are dependent on plate geometry and irradiation conditions, thus, if stress based criteria is used to predict plate behavior (as opposed to material impurities, fine micro-structural defects, or sharp power gradients), unique 3D finite element formulation for each plate is required.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

PROCESS SIMULATION OF COLD PRESSING OF ARMSTRONG CP-Ti POWDERS

A computational methodology is presented for the process simulation of cold pressing of Armstrong CP-Ti Powders. The computational model was implemented in the commercial finite element program ABAQUSTM. Since the powder deformation and consolidation is governed by specific pressure-dependent constitutive equations, several solution algorithms were developed for the ABAQUS user material subroutine, UMAT. The solution algorithms were developed for computing the plastic strain increments based on an implicit integration of the nonlinear yield function, flow rule, and hardening equations that describe the evolution of the state variables. Since ABAQUS requires the use of a full Newton-Raphson algorithm for the stress-strain equations, an algorithm for obtaining the tangent/linearization moduli, which is consistent with the return-mapping algorithm, also was developed. Numerical simulation results are presented for the cold compaction of the Ti powders. Several simulations were conducted for cylindrical samples with different aspect ratios. The numerical simulation results showed that for the disk samples, the minimum von Mises stress was approximately half than its maximum value. The hydrostatic stress distribution exhibits a variation smaller than that of the von Mises stress. It was found that for the disk and cylinder samples the minimum hydrostatic stresses were approximately 23 and 50% less than its maximum value, respectively. It was also found that the minimum density was noticeably affected by the sample height.

36 MATERIALS SCIENCE↗