SEARCH · Search NASA

Results for “Sensible heat”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Surface energy fluxes on four slope sites during FIFE 1988

Four slopes (facing north, south, east, and west) in the Konza Prairie Research Natural Area were selected to study the effect of topography on surface energy balance and other micrometeorological variables. Energy fluxes, air temperature, and vapor pressure were measured on the slopes throughout the 1988 growing season. Net radiation was highest on the south facing slope and lowest on the north facing slope, and the difference was more than 150 W/sq m (20-30 percent) at solar noon. For daily averages the difference was about 25 W/sq m (15 percent) early in the season and increased to about 60 W/sq m (30-50 percent) in September. Soil heat fluxes were similar for all the slopes. The absolute values of sensible heat flux were consistently lower on the north facing slope compared with other slopes. The south facing slope had the greatest day-to-day fluctuation in latent heat flux as a result of the interaction of net radiation, soil moisture, and green leaf area. Differences were found in the partitioning of the available energy among the slopes, and the north facing slope had a higher percentage of energy dissipated into latent heat flux. The north facing slope had higher air temperatures during the day and higher vapor pressures both during the day and at night when the wind was from the south.

Nie, D.↗

NASA NTRS2020

Mechanisms Associated with Daytime and Nighttime Heat Waves over the Contiguous United States

Heat waves are extreme climate events that have the potential to cause immense stress on human health, agriculture, and energy systems, so understanding the processes leading to their onset is crucial. There is no single accepted definition for heat waves, but they are generally described as a sustained amount of time where temperature exceeds a local threshold. Multiple different temperature variables are potentially relevant, as high values of both daily maximum (Tmax) and minimum (Tmin) temperatures can be detrimental to human health. In this study, we focus explicitly on the different mechanisms associated with summertime heat waves manifested during daytime versus nighttime hours over the contiguous United States. Heat waves are examined using the National Aeronautics and Space Administration (NASA) Modern-Era Retrospective analysis for Research and Applications, Version 2 (MERRA-2). Over 1980–2018, the increase in the number of heat wave days per summer was generally stronger for nighttime heat wave days than daytime heat wave days, with localized regions of significant positive trends. Processes linked with daytime and nighttime heat waves are identified through composite analysis of precipitation, soil moisture, clouds, humidity and fluxes of heat and moisture. Daytime heat waves are associated with dry conditions, reduced cloud cover, and increased sensible heating. Mechanisms leading to nighttime heat waves differ regionally across the US, but they are typically associated with increased clouds, humidity and/or low-level temperature advection. In the Midwest US, enhanced moisture is transported from the Gulf of Mexico during nighttime heat waves.

Extreme events↗

NASA NTRS1994

Modeling tropical Pacific sea surface temperature with satellite-derived solar radiative forcing

Two independent datasets for the solar radiation at the surface derived from satellites are compared. The data derived from the Earth Radiation Budget Experiment (ERBE) is for the net solar radiation at the surface whereas the International Satellite Cloud Climatology Project (ISCCP) data is for the downward flux only and was corrected with a space- and time-varying albedo. The ISCCP net flux is at all times higher than the ERBE flux. The difference can be divided into an offset that decreases with latitude and another component that correlates with high tropical cloud cover. With this latter exception the two datasets provide spatial patterns of solar flux that are very similar. A tropical Pacific Ocean model is forced with these two datasets and observed climatological winds. The upward heat flux is parameterized taking into account separately the longwave radiative, latent, and sensible heat fluxes. Best fit values for the uncertain parameters are found using an optimization procedure that seeks to minimize the difference between model and observed SST by varying the parameters within a reasonable range of uncertainty. The SST field the model produces with the best fit parameters is the best the model can do. If the differences between the model and data are larger than can be accounted for by remaining uncertainties in the heat flux parameterization and forcing data then the ocean model must be held to be at fault. Using this method of analysis, a fundamental model fault is identified. Inadequate treatment of mixed layer/entrainment processes in upwelling regions of the eastern tropical Pacific leads to a large and seasonally varying error in the model SST. Elsewhere the model SST is insufficiently different from observed to be able to identify model errors.

Seager, Richard↗

NASA NTRS1981

Estimating ocean-air heat fluxes during cold air outbreaks by satellite

Nomograms of mean column heating due to surface sensible and latent heat fluxes were developed. Mean sensible heating of the cloud free region is related to the cloud free path (CFP, the distance from the shore to the first cloud formation) and the difference between land air and sea surface temperatures, theta sub 1 and theta sub 0, respectively. Mean latent heating is related to the CFP and the difference between land air and sea surface humidities q sub 1 and q sub 0 respectively. Results are also applicable to any path within the cloud free region. Corresponding heat fluxes may be obtained by multiplying the mean heating by the mean wind speed in the boundary layer. The sensible heating estimated by the present method is found to be in good agreement with that computed from the bulk transfer formula. The sensitivity of the solutions to the variations in the initial coastal soundings and large scale subsidence is also investigated. The results are not sensitive to divergence but are affected by the initial lapse rate of potential temperature; the greater the stability, the smaller the heating, other things being equal. Unless one knows the lapse rate at the shore, this requires another independent measurement. For this purpose the downwind slope of the square of the boundary layer height is used, the mean value of which is also directly proportional to the mean sensible heating. The height of the boundary layer should be measurable by future spaceborn lidar systems.

Chou, S. H.↗

NASA NTRS1978

Storage systems for solar thermal power

The development status is reviewed of some thermal energy storage technologies specifically oriented towards providing diurnal heat storage for solar central power systems and solar total energy systems. These technologies include sensible heat storage in caverns and latent heat storage using both active and passive heat exchange processes. In addition, selected thermal storage concepts which appear promising to a variety of advanced solar thermal system applications are discussed.

Calogeras, J. E.↗

NASA NTRS1978

Storage systems for solar thermal power

A major constraint to the evolution of solar thermal power systems is the need to provide continuous operation during periods of solar outage. A number of high temperature thermal energy storage technologies which have the potential to meet this need are currently under development. The development status is reviewed of some thermal energy storage technologies specifically oriented towards providing diurnal heat storage for solar central power systems and solar total energy systems. These technologies include sensible heat storage in caverns and latent heat storage using both active and passive heat exchange processes. In addition, selected thermal storage concepts which appear promising to a variety of advanced solar thermal system applications are discussed.

Calogeras, J. E.↗

NASA NTRS1991

Regenerative adsorbent heat pump

A regenerative adsorbent heat pump process and system is provided which can regenerate a high percentage of the sensible heat of the system and at least a portion of the heat of adsorption. A series of at least four compressors containing an adsorbent is provided. A large amount of heat is transferred from compressor to compressor so that heat is regenerated. The process and system are useful for air conditioning rooms, providing room heat in the winter or for hot water heating throughout the year, and, in general, for pumping heat from a lower temperature to a higher temperature.

Jones, Jack A.↗

NASA NTRS2012

Correction of Excessive Precipitation over Steep Mountains in a General Circulation Model (GCM)

Excessive precipitation over steep and high mountains (EPSM) is a well-known problem in GCMs and regional climate models even at a resolution as high as 19km. The affected regions include the Andes, the Himalayas, Sierra Madre, New Guinea and others. This problem also shows up in some data assimilation products. Among the possible causes investigated in this study, we found that the most important one, by far, is a missing upward transport of heat out of the boundary layer due to the vertical circulations forced by the daytime subgrid-scale upslope winds, which in turn is forced by heated boundary layer on the slopes. These upslope winds are associated with large subgrid-scale topographic variance, which is found over steep mountains. Without such subgrid-scale heat ventilation, the resolvable-scale upslope flow in the boundary layer generated by surface sensible heat flux along the mountain slopes is excessive. Such an excessive resolvable-scale upslope flow in the boundary layer combined with the high moisture content in the boundary layer results in excessive moisture transport toward mountaintops, which in turn gives rise to excessive precipitation over the affected regions. We have parameterized the effects of subgrid-scale heated-slope-induced vertical circulation (SHVC) by removing heat from the boundary layer and depositing it in the layers higher up when topographic variance exceeds a critical value. Test results using NASA/Goddard's GEOS-5 GCM have shown that the EPSM problem is largely solved.

Chao, Winston C.↗

NASA NTRS2012

Correction of Excessive Precipitation Over Steep and High Mountains in a General Circulation Model

Excessive precipitation over steep and high mountains (EPSM) is a well-known problem in GCMs and meso-scale models. This problem impairs simulation and data assimilation products. Among the possible causes investigated in this study, we found that the most important one, by far, is a missing upward transport of heat out of the boundary layer due to the vertical circulations forced by the daytime upslope winds, which are forced by the heated boundary layer on subgrid-scale slopes. These upslope winds are associated with large subgrid-scale topographic variation, which is found over steep and high mountains. Without such subgridscale heat ventilation, the resolvable-scale upslope flow in the boundary layer generated by surface sensible heat flux along the mountain slopes is excessive. Such an excessive resolvablescale upslope flow combined with the high moisture content in the boundary layer results in excessive moisture transport toward mountaintops, which in turn gives rise to EPSM. Other possible causes of EPSM that we have investigated include 1) a poorly-designed horizontal moisture flux in the terrain-following coordinates, 2) the condition for cumulus convection being too easily satisfied at mountaintops, 3) the presence of conditional instability of the computational kind, and 4) the absence of blocked flow drag. These are all minor or inconsequential. We have parameterized the ventilation effects of the subgrid-scale heated-slope-induced vertical circulation (SHVC) by removing heat from the boundary layer and depositing it in layers higher up when the topographic variance exceeds a critical value. Test results using NASA/Goddard's GEOS-S GCM have shown that this largely solved the EPSM problem.

Chao, Winston C.↗

NASA NTRS2014

Temperature Oscillation in a Loop Heat Pipe with Gravity Assist

ATLAS Laser Thermal Control System (LTCS) thermal vacuum testing where the condenser-radiator was placed in a vertical position, it was found that the loop heat pipe (LHP) reservoir required much more control heater power than the analytical model had predicted. The required control heater power was also higher than the liquid subcooling entering the reservoir using the measured temperatures and the calculated mass flow rate based on steady state LHP operation. This presentation describes the investigation of the LHP behaviors under a gravity assist mode with a very cold radiator sink temperature and a large thermal mass attached to the evaporator. It is concluded that gravity caused the cold liquid to drop from the condenser-radiator to the reservoir, resulting in a rapid decrease of the reservoir temperature. When the reservoir temperature was increasing, a reverse flow occurred in the liquid line, carrying warm liquid to the condenser-radiator. Both events consumed the reservoir control heater power. The fall and rise of the reservoir temperature also caused the net heat input to the evaporator to vary due to the release and storage of the sensible heat of the thermal mass. The combination of these effects led to a persistent reservoir temperature oscillation and a repeated influx of cold liquid from the condenser. This was the root cause of the extraordinary high control heater power requirement in the LTCS TV test. Without gravity assist, such a persistent temperature oscillation will not be present.

000↗

NASA NTRSDate not supplied

TPSAS-NF1676L-31980-DND

Background and Objective: The surface temperature of the Arctic is projected to warm more than any other region on Earth (i.e., Arctic Amplification). Even though the increase of solar absorption, due to the reduction of the surface albedo associated with the loss of sea ice, is strongest in summer, the warming is largest in late fall/early winter and smallest in summer. The most common theory put forward to explain the suppressed summer warming is that most of the additional solar energy goes into the melting of sea ice. The energy gain in summer, however, is thought to lead to the Arctic warming maximum in late fall/early winter by leading to enhanced heat release during this time period as a result of the enhanced surface latent and sensible heat fluxes into the atmosphere, also a consequence of the loss and thinning of sea-ice, warming the surface air temperature. While this commonly accepted theory makes clear the importance of sea-ice loss on Arctic warming, by focusing on surface skin temperature our study proposes a differing perspective on how sea-ice decline amplifies Arctic warming and establishes its seasonal pattern.

Sergio A. Sejas↗

NASA NTRS2007

Interannual and Decadal Variability of Ocean Surface Latent Heat Flux as Seen from Passive Microwave Satellite Algorithms

Ocean surface turbulent fluxes are critical links in the climate system since they mediate energy exchange between the two fluid systems (ocean and atmosphere) whose combined heat transport determines the basic character of Earth's climate. Deriving physically-based latent and sensible heat fluxes from satellite is dependent on inferences of near surface moisture and temperature from coarser layer retrievals or satellite radiances. Uncertainties in these "retrievals" propagate through bulk aerodynamic algorithms, interacting as well with error properties of surface wind speed, also provided by satellite. By systematically evaluating an array of passive microwave satellite algorithms, the SEAFLUX project is providing improved understanding of these errors and finding pathways for reducing or eliminating them. In this study we focus on evaluating the interannual variability of several passive microwave-based estimates of latent heat flux starting from monthly mean gridded data. The algorithms considered range from those based essentially on SSM/I (e.g. HOAPS) to newer approaches that consider additional moisture information from SSM/T-2 or AMSU-B and lower tropospheric temperature data from AMSU-A. On interannual scales, variability arising from ENSO events and time-lagged responses of ocean turbulent and radiative fluxes in other ocean basins (as well as the extratropical Pacific) is widely recognized, but still not well quantified. Locally, these flux anomalies are of order 10-20 W/sq m and present a relevant "target" with which to verify algorithm performance in a climate context. On decadal time scales there is some evidence from reanalyses and remotely-sensed fluxes alike that tropical ocean-averaged latent heat fluxes have increased 5-10 W/sq m since the early 1990s. However, significant uncertainty surrounds this estimate. Our work addresses the origin of these uncertainties and provides statistics on time series of tropical ocean averages, regional space / time correlation analysis, and separation of contributions by variations in wind and near surface humidity deficit. Comparison to variations in reanalysis data sets is also provided for reference.

Robertson, Franklin R.↗

NASA NTRS2020

El Niño Related Tropical Land Surface Water and Energy Response in MERRA-2

Though El Niño events each have distinct evolutionary character they typically provide systematic large scale forcing for warming and increased drought frequency across the tropical continents. We assess this response in the MERRA-2 reanalysis and in a ten-member model AMIP ensemble. The lagged response (3-4 months) of mean tropical land temperature to El Niño warming in the Pacific Ocean is well represented. MERRA-2 reproduces the patterns of precipitation in the tropical regions, while the AMIP ensemble reproduces some regional responses better than others. Model skill is dependent on event forcing strength and temporal proximity to the peak of the sea surface warming. A composite approach centered on maximum Niño3.4 SSTs and lag relationships to energy fluxes and transports is used to identify mechanisms supporting tropical land warming. The composite necessarily moderates weather scale variability of the individual events, while retaining the systematic features across all events. We find that that reduced continental upward motions lead to reduced cloudiness and more shortwave radiation at the surface, as well as reduced precipitation. The increased shortwave heating at the land surface, along with reduced soil moisture leads to warmer surface temperature, more sensible heating and warming of the lower troposphere. While the composite provides a broad picture of the mechanisms governing the hydrologic response to El Niño forcing, the regional and temporal response in any given event can be quite variable. The 2015-16 El Niño, one of the strongest events, demonstrates some of the forced response noted in the composite, but with shifts in the evolution that depart from the composite, demonstrating the limitations of the composite and individuality of El Niño.

Michael G Bosilovich↗

NASA NTRS2023

Concepts for the Liquefaction of Hydrogen for In-Situ Operations on the Lunar or Martian Surface

While oxygen will probably be the first fluid liquefied from in-situ developed propellants, hydrogen will also be a sought-after commodity on both the Lunar and Martian surfaces. General hydrogen liquefaction processes are not significantly affected by the atmosphere on Mars and similar processes can be applied on both surfaces. However, hydrogen will require different processes than oxygen (which can be directly liquefied into its final use tank) due to the different spin states the hydrogen nucleus (i.e. parahydrogen and orthohydrogen) can have as well as the significant sensible energy that has to be removed prior to the actual phase change. Due to the low efficiency of 20 K class cryocoolers and high sensible heat removal requirements at higher temperatures, significant benefits can be obtained by precooling the hydrogen gas in a variety of manners. The benefits of three concepts are explored to take advantage of different precooling technics as well as accounting for sensible, latent, and para to ortho conversion heating requirements. Process concepts are shown that can reduce the base input power requirements for heat removal by more than 67% and the radiator area by similar amounts. A majority of the technology development for these processes has already begun, both within NASA and externally, with the few gaps being identified.

ISRU↗

NASA NTRS2023

Concepts for the Liquefaction of Hydrogen for In-Situ Operations on the Lunar or Martian Surface

ISRU↗

NASA NTRS2009

Combining Satellite Microwave Radiometer and Radar Observations to Estimate Atmospheric Latent Heating Profiles

In this study, satellite passive microwave sensor observations from the TRMM Microwave Imager (TMI) are utilized to make estimates of latent + eddy sensible heating rates (Q1-QR) in regions of precipitation. The TMI heating algorithm (TRAIN) is calibrated, or "trained" using relatively accurate estimates of heating based upon spaceborne Precipitation Radar (PR) observations collocated with the TMI observations over a one-month period. The heating estimation technique is based upon a previously described Bayesian methodology, but with improvements in supporting cloud-resolving model simulations, an adjustment of precipitation echo tops to compensate for model biases, and a separate scaling of convective and stratiform heating components that leads to an approximate balance between estimated vertically-integrated condensation and surface precipitation. Estimates of Q1-QR from TMI compare favorably with the PR training estimates and show only modest sensitivity to the cloud-resolving model simulations of heating used to construct the training data. Moreover, the net condensation in the corresponding annual mean satellite latent heating profile is within a few percent of the annual mean surface precipitation rate over the tropical and subtropical oceans where the algorithm is applied. Comparisons of Q1 produced by combining TMI Q1-QR with independently derived estimates of QR show reasonable agreement with rawinsonde-based analyses of Q1 from two field campaigns, although the satellite estimates exhibit heating profile structure with sharper and more intense heating peaks than the rawinsonde estimates. 2

Grecu, Mircea↗

NASA NTRS1982

Some effects of global dust storms on the atmospheric circulation of Mars

A zonally symmetric primitive equation modelled on a sphere is used to numerically simulate the Martian atmosphere's response to various dust loads, as well as the ability of its meridional circulation to transport dust globally, where the circulation is driven by heating due to the absorption of solar and IR radiation by dust and CO2, in addition to sensible heat exchange with the ground. A preliminary experiment shows the model distribution of winds and temperature to compare favorably with zonally averaged values from a general circulation model. Experiments simulating the evolution of global dust storms show that dust is effectively transported by the zonal mean circulation, which rapidly intensifies as the dust spreads, and that the basic structure of the circulation is relatively insensitive to details, being mostly dependent on the heating of the tropical and subtropical atmosphere.

Haberle, R. M.↗

NASA NTRS1986

Generation of available potential energy and the energy cycle during the global weather experiment

Two major themes were pursued during this research period. The first of these involved examining the impacts of satellite-based data and the forecast model used by the Goddard Laboratory for Atmospheres (GLA) on general circulation statistics. For the other major topic, the diabatic heating fields produced by GLA were examined for one month during the FGGE First Special Observing Period. As part of that effort, the three-dimensional distribution of the four component heating fields were studied, namely those due to shortwave radiation, Q sub SW, longwave radiation, Q sub LW, sensible heating, Q sub S, and latent heating, Q sub L. These components were calculated as part of the GLA analysis/forecast system and archived every quarter day; from these archives cross products with temperature were computed to enable the direct calculation of certain terms of the large-scale atmospheric energy cycle, namely those involving the generation of available potential energy (APE). The decision to archive the diabatic heating components separately has enabled researchers to study the role of the various processes that drive the energy cycle of the atmosphere.

Salstein, D. A.↗