Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shear strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of die design on microstructure and mechanical joint strength in friction self-piercing riveted AA7055-T76 and AA7055-T76

In the present study, a unique friction self-piercing riveting (F-SPR) was applied to join high-strength, low-ductility aluminum alloy (AA) 7055-T76 and AA7055-T76 to mitigate a cracking issue. Also, the effect of die design on both joint formation and the mechanical joint performance were investigated. A crack-free joint was achieved when joining AA7055-T76 and AA7055-T76 by F-SPR. As the bottom diameter of the die increased, the mechanical interlocking distance initially increased then became almost saturated. At the same time, the solid-state bonding gradually disappeared, and the lap-shear fracture changed from bottom aluminum fracture to rivet pull-out with partial bottom aluminum fracture. The average maximum lap-shear joint strength of 11.57 kN and cross tension of 5.65 kN were achieved from the D2 die design owing to the combined contributions from high mechanical interlocking distance and good solid-state bonding at the joint interface. Ultrafine grain refinement was observed at the region next to the rivet shank outer surface and along the materials flow line between the top and bottom aluminum sheet in the rivet cavity. Further, because of the same joint-process parameters, the hardness profile at the joints made by different dies did not show obvious differences. As the distance from the base metal to the rivet outer surface decreased, frictional heat caused the hardness to initially decrease from 190 to 150 HV in the heat-affected zone. Hardness increased up to 175 HV in the thermomechanical affected zone (TMAZ-I) owing to large plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Predicting Asteroid Material Properties from a DART-like Kinetic Impact

Abstract NASA’s Double Asteroid Redirection Test (DART) mission is the first full-scale test of the kinetic impactor method for asteroid deflection, in which a spacecraft intentionally impacts an asteroid to change its trajectory. DART represents an important first step for planetary defense technology demonstration, providing a realistic assessment of the effectiveness of the kinetic impact approach on a near-Earth asteroid. The momentum imparted to the asteroid is transferred from the impacting spacecraft and enhanced by the momentum of material ejected from the impact site. However, the magnitude of the ejecta contribution is dependent on the material properties of the target. These properties, such as strength and shear modulus, are unknown for the DART target asteroid, Dimorphos, as well as most asteroids since such properties are difficult to characterize remotely. This study examines how hydrocode simulations can be used to estimate material properties from information available post-impact, specifically the asteroid size and shape, the velocity and properties of the impacting spacecraft, and the final velocity change imparted to the asteroid. Across >300 three-dimensional simulations varying seven material parameters describing the asteroid, we found many combinations of properties could reproduce a particular asteroid velocity. Additional observations, such as asteroid mass or crater size, are required to further constrain properties like asteroid strength or outcomes like the momentum enhancement provided by impact ejecta. Our results demonstrate the vital importance of having as much knowledge as possible prior to an impact mission, with key material parameters being the asteroid’s mass, porosity, strength, and elastic properties.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Fused deposition modeling (FDM) printed polymers are rarely used as a structural material due to anisotropic and low mechanical properties compared with conventional composites. In recent years, greater need has been expressed for recycling of materials, such as recyclable FDM, at the end of service life to reduce environmental pollution and manufacture cost. However, how the amount of resin uptake in the skin and skin/core interphase affects the bending and shear performance of the sandwich composites when replacing the low strength and ductile core (conventional core) with a high strength and brittle core (FDM printed PLA (polylactic acid) core) still remains unclear. A new manufacturing routine is needed to improve the incorporation of FDM printed polymers in composite structures. In this work, FDM printed PLA was used as core material and sandwiched between two unidirectional glass fiber reinforced polymer (GFRP) skins to form a sandwich composite by compression-molding (CM) process, which provides a good manufacturing strategy for skin/core interphase modification. The significance of the CM process is proved by investigating the effect of resin uptake on bending and in-plane/out-of-plane shear performances. Current first order shear deformation (FSDT) theory lacks a direct connection between the in-plane shear stress and out-of-shear stress in the core region of sandwich composites. With the help of DIC, a connection between the in-plane shear and the out-of-plane shear strain was built and in-plane shear properties can acquire through out-of-plane shear properties, hence reducing the redundancy of sample preparation or the need for simulation. A significant improvement was found compared with the optimized resin uptake (Optimized resin uptake range: 20.43%–22.86 wt%) 3D-printed PLA core sandwich composite and lowest performance sandwich composite (Improvement: in-plane shear strength (~34%)/modulus (~29%), out-of-plane shear strength (~25%)/modulus (~31%), specific peak bending load (~19%)). Finally, compared with balsa core sandwich composites, the 3D-printed cores are suitable for use in composite sandwich structures in many applications with a satisfactory strength-to-weight ratio.

3D-printed core sandwich composite↗
DOE OSTI2023

A study of adhesive bonding in metal–metal, metal–CFRP, and CFRP–CFRP material combinations under shear deformation: Fracture morphologies and damage mechanisms

Safe design of adhesive joining in multi-materials in engineered structures requires the accumulation of numerous experimental data on the failure behavior of various adhesively-bonded material combinations under different loading conditions. The deep understanding of mechanical performance, fracturing morphologies, and main damage mechanisms is also quintessential for accelerating the development of proper physics-based and multi-scale models for assisting the design. Towards this goal, this work presents a comprehensive characterization of the failure behavior of adhesively-bonded metal–metal, metal–CFRP, and CFRP–CFRP material combinations under global shear deformation via single lap shear testing. Thanks to a synergistic combination of measurement methods by using Digital Imaging Correlation (DIC) and 3D optical profilometry, adhesive features on the adherend after failure were quantified and the main progressive damage mechanisms were identified. The characterization performed in this work provides quantitative data that contributes to a better understanding of shear failure in adhesive bonding across different bi-material combinations. Finally, the obtained results have practical implications, including the potential to enhance adhesive bonding design, identify failure causes in adhesive joints, and develop or validate computational models capable of capturing the observed behavior in various adhesively-bonded materials under global shear deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tailored Fiber Placement for Complex Preforms

Tailored Fiber Placement (TFP) offers a novel approach to optimize fiber architecture for the fabrication of complex, structural parts not traditionally suitable for advanced composites. This technology not only offers new routes for weight reduction via metal substitution, it also offers cost reduction through minimization of material scrap and reduced labor. This reduction in component weight leads to increased fuel efficiency, and reduced production energy consumption, thereby, helping to achieve the stated IACMI technical goals. This technology leverages centuries of manufacturing development in support of the textile and embroidery industry. One major drawback to this technology is the lack of commercial or non- proprietary structural performance data and robust analytical tools used to optimize fiber architecture and predict performance. This project was structured to utilize common sub-element features to validate analytical performance tools, generate performance data, and gather cost and performance data on components of interest. This project was designed to give industry sponsors the confidence and ability to take full advantage of TFP to fabricate primary, highly loaded structure and integrate features such as metallic fasteners. The project focused principally on the use of high strength carbon fiber, such as T700, and the use of aerospace epoxy resin matrix to primarily support development of new composite applications in vehicle, aerospace, and industrial markets. This project applied previously developed analytical tools to predict the performance of TFP produced parts. This work focused on developing the pipeline to characterize material in order to accurately predict component performance when modifying the TFP print paths and stitch density. This focused on experimental characterization via standardized ASTM testing, alongside experimental testing of more representative service components by testing curved beam strength, beam shear performance, a large scale TFP lug, and ultimately designing a fully TFP clip bracket that reduced weight and cost compared to a traditional metallic component. The new knowledge gained from this program included: 1) development and demonstration of novel analytical tools applied to analysis of TFP preforms; 2) development and demonstration of a building block approach using coupons and sub-elements to optimize the design of a more complex component; 3) demonstration that optimized fiber orientation using TFP can exceed performance of conventional textile composite materials and can open new applications currently limited to metallic components; 4) Demonstration of performance and cost benefits of the TFP process as compared to metallic and conventional textile composites. Recommendations for follow-on work include development of design allowables to assess the impact of high temperature/moisture exposure or saturation during loading, tracking the impact of stitching needle wear on the performance of parts and ability to stitch thicker preforms, using TFP preforms as local reinforcement at areas of bearing or complex loading, and topology optimization of components by tow steering. The expertise developed during the course of this project can be leveraged to provide commercial engineering design and fabrication services using TFP. UDRI is in the process of formalizing their partnership with Spintech, who will serve as the commercialization partner for this technology and provide molding services and deliver finished components to the end user. UDRI will continue to produce the preforms until the economics allow Spintech to procure its own TFP equipment or lease UDRI equipment, at which point UDRI will step away from manufacture and serve as the engineering and design lead on product development.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Novel Preprocessing Techniques for Enhancing Flowability of Miscanthus

Purpose-grown energy crops possess significant potential as promising feedstocks for biofuel and biochemical production. However, similar to other biomass feedstocks, their utilization has been hindered by handling and feeding challenges such as clogging and segregation, which prevent biorefineries from operating at full capacity. These challenges arise primarily due to particle attributes including irregular shape, high flexibility, and high compressibility, leading to interlocking, high compaction, and significant friction under stress consolidation. To enhance operational reliability, it is crucial to focus on preprocessing techniques to address these issues, alongside accurately characterizing the mechanical and physical properties and flow performance of these feedstocks. This study investigates novel preprocessing techniques, including pelletization and torrefaction, to fundamentally alter these particle attributes and improve flowability. Miscanthus, an herbaceous energy crop, was the primary focus of this study. Samples were processed using a Forest Concepts Crumbler rotary shear system and an oscillating multi-stack screen bed to achieve two nominal (baseline) particle sizes: 6mm and 2mm. The study evaluated the efficiency and energy consumption of size reduction, revealing that while 2mm particles required more energy, they exhibited better flowability and higher yield strength compared to 6mm particles. Shear and compression tests assessed the material's shear strength, internal friction, and elastic modulus, while wedge-shaped hopper tests measured the critical arching distance and mass flow rate. The results provide valuable insights into the mechanical properties and processing efficiency of Miscanthus, contributing to the development of a preprocessing framework that enhances energy efficiency and material flowability in bioenergy production. However, further preprocessing and development are required to optimize this framework fully.

09 - BIOMASS FUELS↗
DOE OSTI2023

Flow Strength Measurements of Wrought and AM SS304L via Pressure Shear Plate Impact Experiments

Pressure-shear plate impact experiments were performed to quantify flow strength of wrought, as-built additively manufactured (AM), and heat-treated and recrystallized AM 304 L stainless steel (SS304L) under combined loading. Impact velocities spanned between 0.03 and 0.24 mm/μs, resulting in corresponding pressures of 0.62–5.93 GPa. Flow strength measurements are comparable for the sample variants across the studied loading conditions; however, shear wave structures significantly differ between sample type. Microstructurally aware simulations indicate local strain differences attributed to anisotropic elastic constants of large grains (~1 mm) in the as-built and heat-treated AM may impede the ability to uniformly transmit a shear wave.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear assisted processing and extrusion of enhanced strength aluminum alloy tubing

Hollow extrusions are used in many industries to make strong, lightweight, and affordable structures. Shear Assisted Processing and Extrusion (ShAPE) enables the extrusion of many alloys, often with noteworthy properties. In this investigation, ShAPE was used to extrude 1 and 2 mm wall tubes of aluminum alloy 6063 measuring 12 mm in diameter at extrusion speeds up to 3.8 m/min. This speed is 10 and 15 times faster than has been reported for any alloy using ShAPE and friction stir back extrusion, respectively. Increasing the extrusion speed from 0.7 to 3.8 m/s resulted in using 68% less process energy at steady state. Microstructural analysis and tensile testing were performed on as-extruded tubes and tubes with a direct T5 heat treatment. Grain refinement from 65 µm to below 20 µm was observed. Growth of macroscale Mg 2 Si strengthening precipitates was not observed. ShAPE processing resulted in recrystallization, and extrusion speed was shown to influence final extrudate texture. Here, transmission electron microscopy analysis revealed that the as-extruded microstructure was free of nanoscale ß" strengthening precipitates. Nanoscale ß" was prominent in direct-aged (T5) ShAPE tubes, similar to a slightly over-aged conventional T6 microstructure. As-extruded tubes had ultimate tensile strengths on par with conventional T5 extrusions and approximately double the total elongation. Tubes that underwent a T5 heat treatment had yield and ultimate strengths averaging 198 and 234 MPa, respectively, with an average total elongation of 11%. The tensile test results are comparable to a conventional T6 heat treatment, but without the solutionization heat treatment step. Mechanical properties either remained flat or improved with increased extrusion speed, which suggests that ShAPE can be scaled up to an industrial process to create energy- and economically efficient high-strength extrusions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

SMATool: Strength of materials analysis toolkit

The study of the strength of materials is a cornerstone in material science and engineering, playing a critical role in shaping the progress and application of materials in diverse industrial sectors. The strength of a material is meticulously examined to understand the behavior of the material under different stress conditions and environments, thereby guiding material selection and structural design. Herein, we introduce the SMATool, a computational toolkit for the efficient calculation and analysis of material strength at both zero and finite temperatures for 3D, 2D, 1D, and tubular 2D-based nanostructures and nanotubes, as well as 1D nanoribbons. The toolkit is capable of calculating tensile, shear, ultimate, yield, and indentation (Vickers' hardness) strengths in various dimensions, as well as the energy storage capacity. We conducted several calculations both at zero and finite temperatures to validate the accuracy and reliability of the developed software. Here, the results show that the SMATool package provides accurate predictions that align with existing data on material strength. SMATool integrates seamlessly with widely used electronic structure codes like VASP and Quantum Espresso, providing a user-friendly interface catering to academic researchers and industry professionals.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Vanishing dynamic strength measured in a transient high-pressure phase of tin

This work reports two independent experimental estimations of the dynamic strength of the body-centered tetragonal (bct) 𝛾 phase of tin, which occurs at pressures above about 9 GPa and transforms promptly back to the ambient 𝛽 phase upon pressure release. Measuring strength in such a transient high-pressure phase is challenging. One measurement used free-surface Richtmyer-Meshkov instabilities generated with gas gun impact. Another set of measurements used ramp-release loading in a pulsed-power facility. Strength estimations came from comparison to simulations using a comprehensive multiphase modeling framework that includes equation of state, shear moduli, and strength separately for each phase, and treats mixed-phase regions. Both experimental methods found the 𝛾-phase strength to be very low, within experimental uncertainty of zero. The existing literature on other materials, by contrast, almost universally reports higher strength in transient high-pressure phases compared with ambient phases. Recent Molecular-Dynamics simulations on tin in the literature showed almost zero deviatoric strength during a deformation-induced bct → bct transformation in which one of the 𝛾-phase 𝑎 axes “flips” to the 𝑐 axis. This reorientation currently provides the most plausible explanation for the low observed strength in 𝛾-phase tin.

36 MATERIALS SCIENCE↗
DOE OSTI2020

10° off-axis testing of CFRP using DIC: A study on strength, strain and modulus

For the determination of the shear properties such as strength, strain and modulus of unidirectionally reinforced composites, nearly a dozen measurement techniques exist, several of which have found their way into standards. One non-standardized method for sheet materials is the 10° off-axis tensile test of unidirectional coupons. The current work focuses on the experimental investigation of tensile testing of CFRP-UD coupon specimens using the 10° off-axis test and DIC strain mapping to measure the full-field deformation response. A sensitivity analysis on the measured stresses, strains and moduli is performed by varying the aspect ratio of the specimens and the location of strain measurement. Test related uncertainties such as the loading angle and specimen preparation details are investigated and quantified with the help of these full-field DIC measurements.

42 ENGINEERING↗
DOE OSTI2021

Interlayer reinforcement of 3D printed concrete by the in-process deposition of U-nails

Highlights: • An in-process interlayer reinforcement approach for 3D concrete printing was proposed through the concurrent deposition of U-nails. • Significant strength and toughness improvement was achieved for U-nail reinforced 3D-printed concrete. • The bridge linking effect and dowel action of U-nails were analysed. • Response surface method were utilised to quantify the effects of U-nails on the interlayer bonding behaviour. 3D concrete printing has tremendous potential for construction manufacturing; however, weak interface bonding between adjacent layers remains a well-known issue that affects the mechanical properties of printed structures. The layers introduce anisotropy and reduce the capacity to resist tensile and shear loads. Reinforcements, inserted perpendicular to the printed layers to traverse the interfaces, can improve these limitations, but the insertion of reinforcements is difficult to achieve in practice, and there are few published studies exploring appropriate methods. This study presents a promising approach using U-shaped nails inserted into concrete during the printing process. The bridging effect and dowel action of the applied U-nails are visualised and analysed to elucidate the toughness improvement. The ultimate tensile strength and shear strength of 3D printed concrete are significantly increased by 145.0% and 220.0%, respectively. U-nails with a filament thickness of 2–2.5 mm are recommended to yield optimal improvement in the interlayer strength.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydro-Mechanical Measurements of Sheared Crystalline Rock Fractures With Applications for EGS Collab Experiments 1 and 2

We present hydro-mechanical measurements that characterize shear on natural fractures in schist, amphibolite, and rhyolite specimens from the enhanced geothermal system (EGS) Collab Project's Experiment 1 and 2 sites (E1 and E2) at the Sanford Underground Research Facility. We employed a triaxial direct shear method augmented with X-ray imaging to perform hydroshearing (injection-induced shearing) and mechanical shearing on naturally fractured specimens at in situ stress conditions. Measurements included fracture permeability, strength, stress-dependent aperture, shear dilation, and frictional strength. Results reveal that in situ natural fractures must be permeable, weak, and shear-oriented to be hydrosheared, and only a subset of the observable in situ fractures were suitable. When sheared, the fracture permeability typically increased by a factor of 10 or more and this increase was retained over time. However, shear slip did not always result in permeability increase. High phyllosilicate content associated with exceptionally weak fractures exhibited poor or even decreased permeability after stimulation. These measurements in combination with site data were used to conduct a slip-tendency analysis for different fracture sets, and we selected the top candidate natural fractures for hydroshearing at the EGS Collab sites. We also found that the lower in situ shear stress and stronger fractures at the E2 site make hydroshearing more challenging than at the E1 site. Overall, the methods and analysis used in our work can be applied to any geothermal project to identify in situ joint sets that are best suited for hydroshearing, which in turn can help to optimize well placement and energy production.

58 GEOSCIENCES↗
DOE OSTI2022

Techno-Economic Analysis for Shear Assisted Processing and Extrusion (ShAPE) of High Strength Aluminum Alloys

Aluminum alloy 7075 (AA7075) is a high strength aluminum alloy (HSAL), attractive for applications such as automotive, aviation, aerospace, defense, and marine applications. However, AA7075 has not yet been widely adopted due slow extrusion speed, high energy use, narrow process window, and sensitivity to incipient melting common in conventional extrusion methods. Alternative extrusion methods may overcome these limitations. New research funded by the U.S. Department of Energy (DOE) Advanced Manufacturing Office (AMO) is exploring the use of a new SPP approach called Shear Assisted Processing and Extrusion (ShAPE) for the manufacture of AA7075 extrusions. Pacific Northwest National Laboratory (PNNL) are leading the development, testing and characterization of ShAPE, which is showing that high speed ShAPE extrusions (e.g., above 12 meters/min) which is significantly faster than the 1-2 meters/min possible with conventional AA7075 extrusions. Initial findings from the economic and energy analysis indicate that AA7075 tubes created with ShAPE use less energy than tubes that are conventionally heated and extruded. The reduction in energy use is primarily a result of using direct chill cast (non-homogenized) billets, eliminating the pre-heating step, and faster extrusion speeds. The TEA model translates CAPEX and O&M costs to a manufacturing cost, and then a minimum sustainable price (MSP) per ton of extruded product for multiple facility capacities. A sample output figure of the TEA model is presented below. It presents results of the preliminary version of the TEA model.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗