Search NASA⌕ Search

SEARCH · Search NASA

Results for “Slab geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Surface waves on a grounded dielectric slab covered by a resistive sheet

This paper examines surface wave propagation in a grounded dielectric slab covered with a resistive sheet. Transcendental equations are derived for each polarization and are solved using iterative techniques. Attention and phase velocity are shown for a representative geometry. The results are applicable to both a grounded slab covered with a resistive sheet and an ungrounded slab covered on each side with a resistive sheet.

Shively, David↗
DOE OSTI2026

Demonstration of thermal fracture limits of gas-cooled Nd:APG-1 and Tm:YLF slabs

High-energy short-pulse laser systems demonstrated to date have been limited to low repetition rates due to significant thermal management challenges associated with scaling these systems to high average power, including the need to understand the thermal fracture limits of laser gain media. In this paper, we demonstrate the thermal fracture limits of two high-average-power gain media in a realistic diode-pumped amplifier geometry: a 5 mm thick Nd:APG-1 slab and a 2 mm thick Tm:YLF slab, both cooled by room-temperature helium gas. Finite element analysis revealed maximum tensile stress at fracture of 25 ± 3 MPa for Nd:APG-1 and 30 ± 3 MPa for Tm:YLF. These stress levels correspond to average volumetric heat loads of 13 ± 1 W/cm 3 in Nd:APG-1 and 247 ± 12 W/cm 3 in Tm:YLF. Additional simulations show geometric scaling: thinner slabs tolerate higher heat loads before fracture, while larger pump spots reach the fracture stress at lower heat loads.

Lasers↗
NASA NTRS1992

Analysis of surface wave propagation in a grounded dielectric slab covered by a resistive sheet

Both parallel and perpendicular polarized surface waves are known to propagate on lossless and lossy grounded dielectric slabs. Surface wave propagation on a grounded dielectric slab covered with a resistive sheet is considered. Both parallel and perpendicular polarizations are examined. Transcendental equations are derived for each polarization and are solved using iterative techniques. Attenuation and phase velocity are shown for representative geometries. The results are applicable to both a grounded slab with a resistive sheet and an ungrounded slab covered on each side with a resistive sheet.

Shively, David G.↗
DOE OSTI2023

An implicit particle code with exact energy and charge conservation for electromagnetic studies of dense plasmas

A collisional particle code based on implicit energy- and charge-conserving methods is presented. A modified version of the particle-suppressed Jacobian-Free Newton-Krylov method that can enhance the solver efficiency is introduced. Mathematically, it is shown that this new approach can be viewed as a fixed-point iteration method for the particle positions. The model can exactly conserve global energy and local charge and can efficiently use time steps larger than the plasma period. In conclusion, the algorithm's ability to simulate dense plasmas accurately and efficiently is quantified by simulating the dynamic compression of a plasma slab via a magnetic piston in 1D planar geometry.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Moisture Sorption and Swelling of Sylgard-184

The report summarizes the quantitative assessment of moisture sorption by Sylgard-184. It is an important ingredient in many of our materials. Moisture sorption for this material has been extensively studied with data from 9 different samples available for analysis. These samples varied in size and geometry. Seven of the 9 samples were thin slabs. The remaining 2 were cylinders, one of which had comparable height and diameter and is therefore considered a 3-D sample. All the samples, except 2 (1D_slab4.06mm and 1D_Sylgard_2016_Sharma) belonged to lot number A1606324. They were all prepared by Tony Rodrigues in the plastics shop in the Summer of 2016 and tested by Hom Sharma between October 2016 and June 2017. 1D_slab4.06mm was also prepared by Tony Rodrigues in the plastics shop in Summer of 2016, however, the sample did not have a lot number. 1D_Sylgard_2016_Sharma was prepared by Hom Sharma in February 2016 and tested potentially around May - June 2016.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1993

On the penetration of the 660 km phase change by mantle downflows

We present a simple analytic model of the interaction of cold convective downwelling currents with an endothermic phase change. The model describes the ponding and lateral spreading of downflows along the phase transition interface. A simple comparison of the vertical forces on the ponding material provides a necessary condition for a downflow to penetrate the phase boundary. This condition is fundamentally dependent on the geometry of the downflow. For planar downwellings, the model predicts a minimum ponding time before the structure can penetrate the phase boundary. For columnar (axisymmetric) downflows, there is no minimum time of spreading required before penetration can proceed. The model thus provides an explanation for the observation that in numerical models of three-dimensional convection with an endothermic phase change, cylindrical downflows penetrate the phase interface while planar ones do not. Since descending slabs in the Earth's mantle display a wide spectrum of geometries between planar and cylindrical (given various trench curvatures, as well as intersections of two or more subduction zones), this phenomenon may explain, in part, why some slabs appear to extend into the lower mantle while others are deflected at the 660 km discontinuity.

Bercovici, David↗
NASA NTRS2012

Variance of the Quantum Dwell Time for a Nonrelativistic Particle

Munoz, Seidel, and Muga [Phys. Rev. A 79, 012108 (2009)], following an earlier proposal by Pollak and Miller [Phys. Rev. Lett. 53, 115 (1984)] in the context of a theory of a collinear chemical reaction, showed that suitable moments of a two-flux correlation function could be manipulated to yield expressions for the mean quantum dwell time and mean square quantum dwell time for a structureless particle scattering from a time-independent potential energy field between two parallel lines in a two-dimensional spacetime. The present work proposes a generalization to a charged, nonrelativistic particle scattering from a transient, spatially confined electromagnetic vector potential in four-dimensional spacetime. The geometry of the spacetime domain is that of the slab between a pair of parallel planes, in particular those defined by constant values of the third (z) spatial coordinate. The mean Nth power, N = 1, 2, 3, . . ., of the quantum dwell time in the slab is given by an expression involving an N-flux-correlation function. All these means are shown to be nonnegative. The N = 1 formula reduces to an S-matrix result published previously [G. E. Hahne, J. Phys. A 36, 7149 (2003)]; an explicit formula for N = 2, and of the variance of the dwell time in terms of the S-matrix, is worked out. A formula representing an incommensurability principle between variances of the output-minus-input flux of a pair of dynamical variables (such as the particle s time flux and others) is derived.

Hahne, Gerhard↗
NASA NTRS1992

Evolution of attached and detached slabs and their associated mantle dynamics

Over the two years of the NASA grant, this project has produced a significant amount of research results related to the plate subduction process and the surface crustal deformation at convergent boundaries (i.e., above subduction zones). While some research objectives are completely accomplished, other research tasks remain active and continue to be investigated at present. A steady state analytic thermal model for subducting slabs was used to examine the torques acting on a descending slab. It is found that gravitational torque vanishes when a slab is dipping either vertically or horizontally, unlike previous studies indicating that the magnitude of gravitational torque decreases as dip angle increases. Subsequently, a new time-dependent, analytic thermal model for a subducting slab was developed. The new model enables us to study transient phenomena associated with plate subduction analytically. On the basis of this model, the nature of slab dip angles was evaluated. Slab dip angles are found to be transient features. As they penetrate into the mantle and increase their lengths, the associated gravitational torque also increases resulting in a downward pulling of the slab to the steeper dip angle. This is especially true once a slab penetrates the olivine-spinel phase boundary at about 400 km depth. However, if the phase transformation does not follow the equilibrium condition, the gravitational torque may have a different behavior. This problem was investigated. Except for fast descending slabs, non-equilibrium phase transformation can only slow down the transient increase of slab dip angles discussed earlier. Its effect is not sufficiently strong to reverse the downward pulling for most of the slabs. However, when slabs subducting at 10 cm/yr or faster, a sufficient amount of metastable olivine can exist beneath 400 km. Because of its low density compared with the surrounding spinel, an upward buoyancy is produced resulting in an upward bending of the slab and possibly an upward rotation of the slab such that smaller dip angles are formed. Seismic studies of the Japanese Slab seem to support this interpretation. The development of oroclinal geometries at convergent boundaries was also examined to study plate obduction which is an important ingredient to the initiation of plate subduction. Although the study suggests that surface features are better modeled by block models, the large scale deformation can be adequately studied by viscous models. Such a model is now under development to complete our original objective to study the initiation of plate subduction. Finally, a three-dimensional, finite element, spherical convective model is developed to study dynamic plate subductions. The model development is now complete and it is being tested to ensure its proper operation. The model is able to generate convection results with a viscosity contrast of about 100. Our research continues to push the viscosity contrast to a level that is appropriate for a subducting slab.

Hsui, Albert T.↗
DOE OSTI2022

(U) SENSMG: First-Order Sensitivities of Neutron Reaction Rates, Reaction-Rate Ratios, Leakage, k eff , α , and Subcritical Multiplication Using PARTISN

SENSMG is a tool for computing first-order sensitivities of neutron reaction rates, reaction-rate ratios, leakage, k eff , α, and subcritical multiplication using the PARTISN multigroup discrete-ordinates code. SENSMG computes sensitivities to all of the transport cross sections and data (total, fission, a nu, chi, and all scattering moments), two edit cross sections (absorption and capture), and the density for every nuclide and energy group. It also computes sensitivities to the mass density for every material and derivatives with respect to all interface locations and outer boundaries. It computes sensitivities to user specified reactions whose cross sections are available in a user-supplied NJOY output file. The tool can be used for one-dimensional spherical and slab (r) and two-dimensional cylindrical (r-z) geometries. The tool can be used for fixed-source and eigenvalue problems. For most responses, the tool implements Generalized Perturbation Theory (GPT) as discussed by Williams and Stacey. The tool is thus limited to computing sensitivities only for GPT-allowable responses. For subcritical multiplication, the tool implements sensitivities derived by O’Brien and Clark. SENSMG has a similar role as the old SWANLAKE (Ref. 8), FORSS (Ref. 9), and SENSIT (Ref. 10) codes. It has capabilities similar to those of SUSD3D (Refs. 11 and 12), which also uses PARTISN. Section II of this report describes the theory behind adjoint-based sensitivities, gives the equations that SENSMG solves, and defines the sensitivities that are output. Section III describes the user interface, including the input file and command line options. Section IV describes the output. Section V gives some notes about the coding that may be of interest. Section VI presents some sample problems and discusses verification, which is ongoing. Section VII lists needs and ideas for future work. Appendix A lists most of the input files whose results are presented in Sec. VI. Appendix B provides some useful details on one of the cross-section libraries that SENSMG supports.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1975

Developments in convective heat transfer models featuring seamless and selected detail surfaces, employing electroless plating

Several model/instrument concepts employing electroless metallic skin were considered for improvement of surface condition, accuracy, and cost of contoured-geometry convective heat transfer models. A plated semi-infinite slab approach was chosen for development and evaluation in a hypersonic wind tunnel. The plated slab model consists of an epoxy casting containing fine constantan wires accurately placed at specified surface locations. An electroless alloy was deposited on the plastic surface that provides a hard, uniformly thick, seamless skin. The chosen alloy forms a high-output thermocouple junction with each exposed constantan wire, providing means of determining heat transfer during tunnel testing of the model. A selective electroless plating procedure was used to deposit scaled heatshield tiles on the lower surface of a 0.0175-scale shuttle orbiter model. Twenty-five percent of the tiles were randomly selected and plated to a height of 0.001-inch. The purpose was to assess the heating effects of surface roughness simulating misalignment of tiles that may occur during manufacture of the spacecraft.

Stalmach, C. J., Jr.↗
NASA NTRS1985

A study of the compatibility of an existing CFD package with a broader class of material constitutions

The flexibility of the PHOENICS computational fluid dynamics package was assessed along two general avenues; parallel modeling and analog modeling. In parallel modeling the dependent and independent variables retain their identity within some scaling factors, even though the boundary conditions and especially the constitutive relations do not correspond to any realistic fluid dynamic situation. PHOENICS was used to generate a CFD model that should exhibit the physical anomalies of a granular medium and permit reasonable similarity with boundary conditions typical to membrane or porous piston loading. A considerable portion of the study was spent prying into the existing code with a prejudice toward rate type and disarming any inherent fluid behavior. The final stages of the study were directed at the more specific problem of multiaxis loading of cylindrical geometry with a concern for the appearance of bulging, cross slab shear failure modes.

French, K. W., Jr.↗
DOE OSTI2024

How to Safely Build 100-plus Kilograms of Weapons-Grade Plutonium

The goal of the EUCLID (Experiments Underpinned by Computational Learning for Improvements in Nuclear Data) project was to reduce compensating errors by utilizing machine learning to both help determine which reactions contain compensating errors as well as optimizing an experiment which can be used to maximally reduce these errors. Compensating errors can adversely impact the predictive power of application simulations, and therefore it’s useful to further constrain nuclear data and reduce these errors. The EUCLID project included building two configurations at the National Criticality Experiments Research Center (NCERC). These two configurations had very different geometries (one was cube-like and one was slab-like). Previous works focus on selection of the target experiment(s), radiation transport capabilities developed in the project, the experiment optimization, and the performance of the experiments. This work will focus only on the safety aspects of performing this experiment, which utilized over 100 kg of weapons-grade plutonium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1976

The prominence-corona interface compared with the chromosphere-corona transition region

The intensities of 52 optically thin EUV emission lines formed at temperatures of 350,000 to 2.2 million K in nine hedgerow prominences observed at the limb are compared with the intensities of the same lines formed within network cells at the center of the solar disk in order to compare the prominence-corona interface (PC) with the chromosphere-corona transition region (CC). It is found for all nine prominences that the ratio of the intensity of a line measured in a cell to that in a prominence decreases with increasing temperature approximately as the -0.6 power of temperature. This ratio is used as the basis for comparing the PC with the CC in the framework of two different geometries wherein the prominence consists of one or more identical fully resolved slabs or threads in the line of sight or contains one or more identical unresolved cylindrical threads. It is concluded that three effects may contribute to the systematic difference between the PC and the CC: (1) the pressure within the PC might increase outward; (2) the temperature gradient within the PC might increase more slowly with temperature than in the CC; and (3) the unresolved internal geometry of a prominence can directly explain some, but not all, of the systematic difference.

Orrall, F. Q.↗
DOE OSTI2025

Thermomechanics coupling to Monte Carlo particle transport on unstructured mesh geometries using Cardinal

Geometry deformation due to thermal expansion influences neutron transport in many systems. Studying this phenomenon involves coupling models for neutronics, thermal hydraulics, and solid mechanics. To enable high fidelity modeling of these coupled physics, new capabilities were introduced in Cardinal, coupling OpenMC Monte Carlo particle transport models with MOOSE thermomechanical physics on unstructured moving-mesh geometries. In this work, we present a fully open-source capability leveraging on-the-fly mesh skinning to automatically regenerate OpenMC geometry, which allows multiphysics feedback from temperature, density, and geometry changes. The new capability is verified using an analytic benchmark slab problem, which couples S 2 neutron transport with thermal conduction, convective boundary conditions, Doppler-broadened cross sections, and nonlinear thermal expansion effects along the heated slab. Cardinal reproduces the analytic solutions for the neutron flux, heating, k eff , and temperature with demonstrated convergence in various error terms including mesh resolution and cross section temperature library spacing. For the nominal benchmark conditions and with a fine mesh, maximum relative errors for neutron flux, temperature, and heating are lower than 1%, while errors in integral quantities such as k eff and slab length are within 1 pcm and 48 µm, respectively. This work (i) presents a new numerical approach to thermomechanics coupling with OpenMC models, (ii) is the first (to our knowledge) to utilize a mechanical partial differential equation (PDE) solution to solve the (Griesheimer and Kooreman, 2022) analytic benchmark, and (iii) develops this verified capability within an open-source package.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Coupling between plasmonic and photonic crystal modes in suspended three-dimensional meta-films

A complementary metal oxide semiconductor (CMOS) compatible fabrication method for creating three-dimensional (3D) meta-films is presented. In contrast to metasurfaces, meta-films possess structural variation throughout the thickness of the film and can possess a sub-wavelength scale structure in all three dimensions. Here we use this approach to create 2D arrays of cubic silicon nitride unit cells with plasmonic inclusions of elliptical metallic disks in horizontal and vertical orientations with lateral array-dimensions on the order of millimeters. Fourier transform infrared (FTIR) spectroscopy is used to measure the infrared transmission of meta-films with either horizontally or vertically oriented ellipses with varying eccentricity. Shape effects due to the ellipse eccentricity, as well as localized surface plasmon resonance (LSPR) effects due to the effective plasmonic wavelength are observed in the scattering response. The structures were modeled using rigorous coupled wave analysis (RCWA), finite difference time domain (Lumerical), and frequency domain finite element (COMSOL). The silicon nitride support structure possesses a complex in-plane photonic crystal slab band structure due to the periodicity of the unit cells. We show that adjustments to the physical dimensions of the ellipses can be used to control the coupling to this band structure. The horizontally oriented ellipses show narrow, distinct plasmonic resonances while the vertically oriented ellipses possess broader resonances, with lower overall transmission amplitude for a given ellipse geometry. We attribute this difference in resonance behavior to retardation effects. The ability to couple photonic slab modes with plasmonic inclusions enables a richer space of optical functionality for design of metamaterial-inspired optical components.

42 ENGINEERING↗
DOE OSTI2026

Cathodic Protection Modeling for Hanford Underground Double-Shell Tank Farms

Hanford stores millions of gallons of radioactive and chemically hazardous waste from the production of weapon materials in tank farms consisting of underground carbon-steel storage tanks surrounded by reinforced concrete. Six of these Hanford tank farms use double-shell storage tanks (DSTs). The DST farms were constructed from 1968 to 1986 with a planned 40–50 year design life, so some are already operating beyond their initial life expectancy. Ultrasonic testing (UT) has indicated significant thinning on the bottom of the secondary (outer) liner of these tanks, believed to arise from groundwater intrusion driving concrete side corrosion. There is no direct access to the steel/concrete interface between the tank and the concrete pad, making it difficult to apply a chemical-based mitigation strategy or to conduct repairs, but cathodic protection (CP) is a possible method to inhibit further concrete-side corrosion. Hanford already uses CP to protect below grade steel piping within the tank farms and connected to the tanks, but this system was not designed to protect the tank bottoms. CP design must account for the structures surrounding the DSTs, including the steel reinforcing bars (rebar) within the concrete pad and vault, various process lines, and the existing CP system. In this study, finite element analysis (FEA) modeling was carried out to simulate CP protection of 1) a single tank and CP anode to develop options for modeling the rebar and to compare to a simpler circuit model and 2) the entire Hanford AN tank farm as a representative example consisting of seven tanks, associated piping, and both existing and new CP anodes. Both circuit and FEA models predict that significant protective current could be delivered to the bottoms of the tanks with the addition of tank-protection anodes below the depth of the tanks. Simulations with only the existing pipe-protection anodes active confirmed that only a very small current to the tank bottoms is predicted under present conditions. Multiple simplified representations of the dome and wall rebar were tested to reduce the computational complexity of the tank-farm simulations, resulting in modeling the rebar as edge elements with a prescribed effective circumference that matches the real rebar surface area. The geometry of the rebar is also simplified into horizontal hoops around the tank walls and radial rebar over the dome with increased effective circumference to retain the target surface area. This simplification was found to greatly reduce the complexity and solution time of the models without large changes in current distributions, especially to the tank bottom. A range of values were tested for model parameters such as soil and concrete resistivities and polarization resistance to investigate their impact on the current and electric potential distributions. Depending on the parameters used, FEA simulations predict some risk of overprotection, particularly on the piping system; since overprotection can also lead to surface damage associated with hydrogen gas generation at the interface (e.g. hydrogen embrittlement or damage to coatings), this needs to be considered when refining the design of the new CP system. Comparison between the FEA models and the circuit model representation demonstrated that the circuit model could not match the predicted FEA current distribution, even when using the exact same surface areas. This discrepancy appeared to be at least partly attributable to the impact of the relative positions of the tank components and anodes to each other and to the ground surface. The FEA model accounts for the relative positions since it solves the governing equations in three dimensions, but the circuit model cannot account for the positioning. In particular, the circuit model underpredicts the current to the tank bottom and overpredicts the current to the dome compared to FEA for the baseline geometry. The FEA models omitted the electrically isolated rebar in the bottom concrete slab. However, a circuit based stray current model estimated that only 2.1% of the total current through the slab would stray into the rebar, corresponding to ~0.21 A for a target current density of 2 mA/ft2 to the tank bottom. The estimated corrosion driven by this amount of stray current is predicted to yield a lifetime of >400 years for the minimum rebar diameter, assuming an acceptable cross-section area loss of 10%.

d'Entremont, Anna [Savannah River National Laborat↗
NASA NTRS1995

Field lines and magnetic surfaces in a two-component slab/2D model of interplanetary magnetic fluctuations

A two-component model for the spectrum of interplanetary magnetic fluctuations was proposed on the basis of ISEE observations, and has found an intriguing level of application in other solar wind studies. The model fluctuations consist of a fraction of 'slab' fluctuations, varying only in the direction parallel to the locally uniform mean magnetic field B(0) and a complement of 2D (two-dimensional) fluctuations that vary in the directions transverse to B(0). We have developed an spectral method computational algorithm for computing the magnetic flux surfaces (flux tubes) associated with the composite model, based upon a precise analogy with equations for ideal transport of a passive scalar in planar two dimensional geometry. Visualization of various composite models will be presented, including the 80 percent 2D/ 20 percent slab model with delta B/B(0) approximately equals 1 and a minus 5/3 spectral law, that is thought to approximately represent a snapshot of solar wind turbulence. Characteristically, the visualizations show that flux tubes, even when defined as regular on some plane, shred and disperse rapidly as they are viewed along the parallel direction. This diffusive process, which generalizes the standard picture of field line random walk, will be discussed in detail. Evidently, the traditional picture that flux tubes randomize like strands of spaghetti with a uniform tangle along the axial direction is in need of modification.

Matthaeus, W. H.↗