Search NASA⌕ Search

SEARCH · Search NASA

Results for “Strain calculation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Fatigue delamination behavior of PEEK thermoplastic composite laminates

The delamination resistance of graphite-reinforced PEEK composites was quantified by conducting static and cyclic edge delamination tests on (35n/-35n/0n/90n)s AS4/PEEK laminates, where n = 1, 2. The experimentally determined mechanical delamination onset strains were used to calculate the critical strain-energy release rate for delamination onset as a function of fatigue cycle. The delamination onset strains decreased dramatically with fatigue cycles and then began to level off to an endurance limit at 1 million cycles. Although the static interlaminar fracture toughness of the AS4/PEEK composite is much greater than the toughness of graphite epoxy composites, the delamination fatigue threshold, calculated from the cyclic strain endurance limit at 1 million cycles, was only slightly greater than the threshold for graphite epoxy composites. The contribution of residual thermal stresses to delamination in the AS4/PEEK is substantial due to the large temperature range between the manufacture and the room temperatures.

O'Brien, T. K.↗

Calculation of radiation induced swelling of uranium mononitride using the digital computer program CYGRO 2

Fuel volume swelling and clad diametral creep strains were calculated for five fuel pins, clad with either T-111 (Ta-8W-2.4Hf) or PWC-11 (Nb-1Zr-0.1C). The fuel pins were irradiated to burnups between 2.7 and 4.6%. Clad temperatures were between 1750 and 2400 F (1228 and 1589 K). The maximum percentage difference between calculated and experimentally measured values of volumetric fuel swelling is 60%.

Davison, H. W.↗

Strain-Energy-Release Rates In Delamination

Q3DG computer program developed to perform quasi-three-dimensional stress analysis of composite laminates containing delaminations. Calculates strain-energy-release rates for long, rectangular composite laminates containing delaminations and subjected to any combination of mechanical, thermal, and hygroscopic loading. Written in FORTRAN V.

Raju, I. S.↗

Delamination growth analysis in quasi-isotropic laminates under loads simulating low-velocity impact

A geometrically nonlinear finite-element analysis was developed to calculate the strain energy released by delamination plates during impact loading. Only the first mode of deformation, which is equivalent to static deflection, was treated. Both the impact loading and delamination in the plate were assumed to be axisymmetric. The strain energy release rate in peeling, G sub I, and shear sliding, G sub II, modes were calculated using the fracture mechanics crack closure technique. Energy release rates for various delamination sizes and locations and for various plate configurations and materials were compared. The analysis indicated that shear sliding (G sub II) was the primary mode of delamination growth. The analysis also indicated that the midplane (maximum transverse shear stress plane) delamination was more critical and would grow before any other delamination of the same size near the midplane region. The delamination growth rate was higher (neutrally stable) for a low toughness (brittle) matrix and slower (stable) for high toughness matrix. The energy release rate in the peeling mode, G sub I, for a near-surface delamination can be as high as 0.5G sub II and can contribute significantly to the delamination growth.

Shivakumar, K. N.↗

Calculation of reinforced-concrete frame strength under a simultaneous static cross section load and a column lateral impact

When designing buildings with reinforced concrete that are planned to resist dynamic loads it is necessary to calculate this structural behavior under operational static and emergency impact and blast loads. Calculations of the structures under shock-wave loads can be performed by solving dynamic equations that do not consider static loads. Due to this fact the calculation of reinforced concrete frame under a simultaneous static and dynamic load in full 3d settings becomes a very non trivial and resource consuming problem. This problem can be split into two tasks. The first one is a shock-wave problem that can be solved using software package RANET-3, which allows solving the problem using finite elements method adapted for dynamic task. This method calculates strain-stress state of the material and its dynamic destruction, which is considered as growth and consolidation of micro defects under loading. On the second step the results of the first step are taken as input parameters for quasi static calculation of simultaneous static and dynamic load using finite elements method in AMP Civil Engineering-11.

36 MATERIALS SCIENCE↗

EXPERIMENTAL-BASED DISCUSSION FOR THE SEPARATION OF RESIDUAL STRESSES AND COLD WORK IN SHOT PEENED IN718 USING HIGH FREQUENCY EDDY CURRENT SPECTROSCOPY

Typical aero engine alloys, such as IN718, can be surface-treated by shot peening to induce near-surface compressive strains. To calculate the remaining operation time for those critical aero engine components, a quantitative nondestructive determination of near-surface strain gradients has to be developed. We have demonstrated in the past, that it is possible to obtain a characteristic depth profile (surface and sub-surface) of the electrical conductivity of shot peened specimen by using high-frequency eddy current techniques. The measured conductivity profile is resulting from residual stresses, cold work, surface roughness, and the microstructure of the material. The objective is to measure residual stresses (separately from other material properties) in such components after a defined life time. It can be assumed, that surface roughness and microstructure remain unchanged in IN718 materials over their lifetime, but cold work and residual stresses can change independently. Consequently, there is a need to clearly separate the information from both material properties of received eddy current conductivity signals in order to obtain specific information related to residual stresses. This paper presents results acquired from different experiments, conducted to separate both effects by using the eddy current technique on shot peened IN718 materials. We present different physical approaches and illustrate the experiments to solve them. In addition, we will demonstrate that there is a need to use additional techniques, for example ultrasonic time-of-flight measurements, to separate the effects of residual stresses from compound (mixed) signals obtained on cold work samples.

36 MATERIALS SCIENCE↗

Three-dimensional local residual stress and orientation gradients near graphite nodules in ductile cast iron [3D local residual stress and orientation gradients near graphite nodules in ductile cast iron]

A synchrotron technique, differential aperture X-ray microscopy (DAXM), has been applied to characterize the microstructure and analyze the local mesoscale residual elastic strain fields around graphite nodules embedded in ferrite matrix grains in ductile cast iron. Compressive residual elastic strains are measured with a maximum strain of ~6.5–8 × 10 –4 near the graphite nodules extending into the matrix about 20 μm, where the elastic strain is near zero. The experimental data are compared with a strain gradient calculated by a finite element model, and good accord has been found but with a significant overprediction of the maximum strain. This is discussed in terms of stress relaxation during cooling or during storage by plastic deformation of the nodule, the matrix or both. Furthermore, relaxation by plastic deformation of the ferrite is demonstrated by the formation of low energy dislocation cell structure also quantified by the DAXM technique.

36 MATERIALS SCIENCE↗

Quantitative comparison between the degree of domain orientation and nonlinear properties of a PZT ceramic during electrical and mechanical loading

The macroscopic electromechanical coupling properties of ferroelectric polycrystals are composed of linear and nonlinear contributions. The nonlinear contribution is typically associated with the extrinsic effects related to the creation and motion of domain walls. To quantitatively compare the macroscopic nonlinear properties of a lead zirconate titanate ceramic and the degree of domain orientation, in-situ neutron and high-energy x-ray diffraction experiments are performed and they provide the domain orientation density as a function of the external electric field and mechanical compression. Furthermore, the macroscopic strain under the application of external electrical and mechanical loads is measured and the nonlinear strain is calculated by means of the linear intrinsic piezoelectric effect and the linear intrinsic elasticity. The domain orientation density and the nonlinear strain show the same dependence on the external load. The scaling factor that relates to the two values is constant and is the same for both electrical and mechanical loadings.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Investigation of Anomalous Behavior in Metallic-Based Materials Under Compressive Loading

An anomalous material response has been observed under the action of applied compressive loads in fibrous SiC/Ti (both Ti-6242 and Ti-15-3 alloys) and the monolithic nickel-base alloy IN-718 in the aged condition. The observed behavior is an increase, rather than a decrease, in the instantaneous Young's modulus with increasing load. This increase is small, but can be significant in yield surface determination tests, where an equivalent offset strain on the order of 10 micron(1 x 10(exp -6) m/m) is being used. Stiffening has been quantified by calculating offset strains from the linear elastic loading line. The offset strains associated with stiffening during compressive loading are positive and of the same order as the target offset strains in yield surface determination tests. At this time we do not have a reasonable explanation for this response nor can we identify a deformation mechanism that might cause it. On the other hand, we are not convinced that it is an artifact of the experimental procedure because a number of issues have been identified and seemingly ruled out. In fact, stiffening appears to be temperature dependent, since it decreases as the temperature increases.

Gil, Christopher M.↗

Micromechanical Fields Associated with Irregular Deformation Twins in Magnesium

Understanding and controlling the development of deformation twins is paramount for engineering strong and stable hexagonal close-packed (HCP) Mg alloys. Actual twins are often irregular in boundary morphology and twin crystallography, deviating from the classical picture commonly used in theory and simulation. In this work, the elastic strains and stresses around irregular twins are examined both experimentally and computationally to gain insight into how twins develop and the microstructural features that influence their development. A nanoprecession electron diffraction (N-PED) technique is used to measure the elastic strains within and around a $\left\{ {10\overline{1}2} \right\}$ tensile twin in AZ31B Mg alloy with nm scale resolution. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) crystal plasticity model of the same sub-grain and irregular twin structure is employed to understand and interpret the measured elastic strain fields. The calculations predict spatially resolved elastic strain fields in good agreement with the measurement, as well as all the stress components and the dislocation density fields generated by the twin, which are not easily obtainable from the experiment. The model calculations find that neighboring twins, several twin thicknesses apart, have little influence on the twin-tip micromechanical fields. Furthermore, this work reveals that irregularity in the twin-tip shape has a negligible effect on the development of the elastic strains around and inside the twin. Importantly, the major contributor to these micromechanical fields is the alignment of the twinning shear direction with the twin boundary.

36 MATERIALS SCIENCE↗

Simple effective conservative treatment of uncertainty from sparse samples of random functions

This paper examines the variability of predicted responses when multiple stress-strain curves (reflecting variability from replicate material tests) are propagated through a finite element model of a ductile steel can being slowly crushed. Over 140 response quantities of interest (including displacements, stresses, strains, and calculated measures of material damage) are tracked in the simulations. Each response quantity’s behavior varies according to the particular stress-strain curves used for the materials in the model. We desire to estimate response variability when only a few stress-strain curve samples are available from material testing. Propagation of just a few samples will usually result in significantly underestimated response uncertainty relative to propagation of a much larger population that adequately samples the presiding random-function source. A simple classical statistical method, Tolerance Intervals, is tested for effectively treating sparse stress-strain curve data. The method is found to perform well on the highly nonlinear input-to-output response mappings and non-standard response distributions in the can-crush problem. The results and discussion in this paper support a proposition that the method will apply similarly well for other sparsely sampled random variable or function data, whether from experiments or models. Finally, the simple Tolerance Interval method is also demonstrated to be very economical.

36 MATERIALS SCIENCE↗

Inter- and intra-plate deformation at North American plate boundaries

A geodetic network which spans the region between San Francisco and Lake Tahoe has been measured 5 times completely with triangulation in 1880, 1922, 1929, 1943, 1963. A resurvey with the Global Positioning System (GPS) in 1991 allows the formation of 1 coseismic and 4 interseismic epochs. The data from this network provide a unique opportunity to examine the temporal and spatial evolution of the strain field associated with the 1906 San Francisco earthquake in particular and with the Pacific-North American plate boundary in general. Calculations of strain rate from the network data lead to the following conclusions. (1) There is no resolvable (greater than 0.05 microradians/yr) strain in between Sutter Buttes and the Sierra Nevada. (2) Throughout the time since the 1906 earthquake, a region extending at least as far east as the westernmost Great Valley has been undergoing deformation related to Pac:Nam interaction and the associated earthquake cycle. (3) In the time and space of overlap, our results agree with those from the United States Geological Survey (USGS) trilateration data. Both data sets indicate that strain must be accumulating to the east of Vaca. (4) The San Andreas discrepancy cannot be accommodated in the Great Valley at the 1 sigma level of our results. It is possible to absorb it in that region at the 2 sigma level. (5) Strain rate is elevated in the years following the earthquake and decays slowly with time. It is possible that the rate in the Coast Ranges increases until around 1950 and then decays. With the exception of one epoch, strain rate in the Coast Ranges is consistently fault parallel, shows no sign changes, and is consistent with monotonic strain accumulation.

Beavan, John↗

Formation and Migration Energies of Interstitials in Silicon Under Strain Conditions

Simulation calculations are conducted for Si substrates to analyze formation and diffusion energies of interstitials under strain condition using statics methods .based on a Stillinger-Weber type potential function. Defects in the vicinity of the surface region and in the bulk are examined, and the role played by compressive and tensile strains on the energetics of interstitials is investigated. Results indicate that strain alters defect energetics which, in turn, modifies their diffusion characteristics.

Halicioglu, Timur↗

Modeling damaged wings: Element selection and constraint specification

The NASTRAN analytical program was used for structural design, and no problems were anticipated in applying this program to a damaged structure as long as the deformations were small and the strains remained within the elastic range. In this context, NASTRAN was used to test three-dimensional analytical models of a damaged aircraft wing under static loads. A comparison was made of calculated and experimentally measured strains on primary structural components of an RF-84F wing. This comparison brought out two sensitive areas in modeling semimonocoque structures. The calculated strains were strongly affected by the type of elements used adjacent to the damaged region and by the choice of multipoint constraints sets on the damaged boundary.

Stronge, W. J.↗

Nonlinear temperature dependent failure analysis of finite width composite laminates

A quasi-three dimensional, nonlinear elastic finite element stress analysis of finite width composite laminates including curing stresses is presented. Cross-ply, angle-ply, and two quasi-isotropic graphite/epoxy laminates are studied. Curing stresses are calculated using temperature dependent elastic properties that are input as percent retention curves, and stresses due to mechanical loading in the form of an axial strain are calculated using tangent modulii obtained by Ramberg-Osgood parameters. It is shown that curing stresses and stresses due to tensile loading are significant as edge effects in all types of laminate studies. The tensor polynomial failure criterion is used to predict the initiation of failure. The mode of failure is predicted by examining individual stress contributions to the tensor polynomial.

Nagarkar, A. P.↗

Dynamic delamination fracture toughness of a graphite/epoxy laminate under impact

Dynamic delamination fracture toughness in a (90/0)5s T300/934 graphite/epoxy laminate was investigated using impact loading. Delamination cracks of three different sizes were embedded at the midplane of the composite specimen. The threshold impact velocity that causes propagation of the delamination crack was used in the dynamic analysis with the finite element method. From the finite element solution, the time-history of the strain energy release rate was calculated. The critical strain energy release rate was taken to equal the maximum value of the response history.

Sun, C. T.↗

Effect of boundary conditions on dynamic strain response of rectangular panels

An analytical and experimental research program has been initiated at NASA Langley to investigate the strain response of panels under severe thermal and/or acoustic loads. The overall purpose of this program is to develop an analytical model that predicts the stresses and strains leading to sonic fatigue failure in advanced aircraft and aerospace structures. Previous experiments, analyses, and results of this program are reviewed. The analytical modeling refinements and their effects on the calculation of strain are discussed, considering the inclusion of in-plane motion at the panel boundary; the use of the multiterm, multimode Ritz method; and the introduction of transverse stiffness at the boundary. Finally, the findings of the analytical modeling investigation are summarized.

Roussos, Louis A.↗

Strain-induced stabilization of Al functionalization in graphene oxide nanosheet for enhanced NH{sub 3} storage

Strain effects on the stabilization of Al ad-atom on graphene oxide (GO) nanosheet as well as its implications for NH{sub 3} storage have been investigated using first-principles calculations. Tensile strain is found to be very effective in stabilizing the Al ad-atom on GO. It strengthens the C-O bonds through an enhanced charge transfer from C to O atoms. Interestingly, Al's stability is governed by the bond strength of C-O rather than that of Al-O. Optimally strained Al-functionalized GO binds up to 6 NH{sub 3} molecules, while it binds no NH{sub 3} molecule in unstrained condition.

77 NANOSCIENCE AND NANOTECHNOLOGY↗