Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

A Study on the Surface Composition and Migration of Materials and Their Effect on Surface Microhardness during Micro-EDM of Ti-6Al-4V

This study aims to investigate the effect of machining parameters on the surface topography and composition of Ti-6Al-4V after micro-EDM as well as the effect of elemental composition on the surface microhardness. The surface topography has been studied in terms of quality of machined surface, crater sizes, and the presence of surface defects. Statistical analysis was carried out to study the influence of micro-EDM process parameters, i.e., voltage, capacitance, discharge energy, electrode rotational speed, and the electrode coating, on the elemental composition of the machined surface. It was found that the crater size, and hence the surface finish, was dependent on the electrical parameters only, with more pronounced effect of capacitance over voltage. The 60 V and 30 pF combination resulted in crater size as small as 1 µm, whereas crater size of 12 µm was obtained using a combination of 4700 pF and 112 V. Although smaller capacitance resulted in smaller crater sizes, it also increased the chances of defects or deposition of debris on the machined surface. There was migration of material from the tool electrode, dielectric oil, and atmosphere to the workpiece surface, which influenced the surface topography, crater sizes, and surface microhardness. The effects of non-electrical parameters on the relative percentage of various elements were found to be statistically insignificant. The surface microhardness was found to increase slightly due to the surface modification after EDM. The reason for increase in surface microhardness was identified as the migration of tungsten from the tool electrode and carbon from the dielectric. The maximum surface microhardness of 455 HV was obtained at a surface composition after micro-EDM containing 7.96% C and 9.69% W, where non-machined Ti-6Al-4V surface does not have any carbon or tungsten on the surface.

36 MATERIALS SCIENCE↗

Facet-Dependent Rock-Salt Reconstruction on the Surface of Layered Oxide Cathodes

The surface configuration of pristine layered oxide cathode particles for Li-ion batteries significantly affects the electrochemical behavior, which is generally considered to be a thin rock-salt layer in the surface. Unfortunately, aside from its thin nature and spatial location on the surface, the true structural nature of this surface rock-salt layer remains largely unknown, creating the need to understand its configuration and the underlying mechanisms of formation. Using scanning transmission electron microscopy, we have found a correlation between the surface rock-salt formation and the crystal facets on pristine LiNi0.80Co0.15Al0.05O2 primary particles. It is found that the originally (01 $ \overline{4}\ $) and (003) surfaces of the layered phase result in two kinds of rock-salt reconstructions: the (002) and (111) rock-salt surfaces, respectively. Stepped surface configurations are generated for both reconstructions. The (002) configuration is relatively flat with monoatomic steps while the (111) configuration shows significant surface roughening. Both reconstructions reduce the ionic and electronic conductivity of the cathode, leading to a reduced electrochemical performance.

Environmental Molecular Sciences Laboratory↗

Initial Reduction of the PdO(101) Surface: Role of Oxygen Vacancy Formation Kinetics

Here, we investigated the initial thermal reduction of the PdO(101) surface using density functional theory (DFT) calculations. The defect-free PdO(101) surface consists of parallel rows of undercoordinated Pd and O atoms (Pd cus and O cus , respectively). DFT was used to map out the elementary processes of O cus vacancy formation, oxygen surface atom diffusion along the Pd cus rows, and various O 2 formation pathways. Because oxygen vacancies form during the reduction of the surface, the elementary processes were examined with and without the presence of adjacent O cus vacancies. DFT calculations show that the presence of oxygen vacancies strongly affects the barriers of adjacent surface processes. Barriers for O vacancy formation are reduced by nearly 50% with an adjacent O vacancy. The barrier for O 2 formation along the Pd cus row drops from 1.54 eV on the defect-free PdO(101) surface to 0.81 eV in the presence of an O cus vacancy dimer. Yet, the presence of O cus vacancies also leads to more strongly bound O 2 on the Pd cus row. The strong neighbor effect of O vacancies on the PdO(101) surface will favor the growth of O vacancy chains and increase the rate of thermal reduction of the surface, both features that have been observed in recent ultrahigh vacuum isothermal reduction experiments of the PdO(101) surface.

Defects in solids↗

Surface structure and stability of partially hydroxylated silica surfaces

Surface energies of silicates influence crack propagation during brittle fracture and decrease with surface relaxation caused by annealing and hydroxylation. Molecular-level simulations are particularly suited for the investigation of surface processes. In this work, classical MD simulations of silica surfaces are performed with two force fields (ClayFF and ReaxFF) to investigate the effect of force field reactivity on surface structure and energy as a function of surface hydroxylation. An unhydroxylated fracture surface energy of 5.1 J/m 2 is calculated with the ClayFF force field, and 2.0 J/m 2 is calculated for the ReaxFF force field. The ClayFF surface energies are consistent with the experimental results from double cantilever beam fracture tests (4.5 J/m 2 ), whereas ReaxFF underestimated these surface energies. Surface relaxation via annealing and hydroxylation was performed by creating a low-energy equilibrium surface. Annealing condensed neighboring siloxane bonds increased the surface connectivity, and decreased the surface energies by 0.2 J/m 2 for ClayFF and 0.8 J/m 2 for ReaxFF. Posthydroxylation surface energies decreased further to 4.6 J/m 2 with the ClayFF force field and to 0.2 J/m 2 with the ReaxFF force field. Experimental equilibrium surface energies are ~0.35 J/m 2 , consistent with the ReaxFF force field. Although neither force field was capable of replicating both the fracture and equilibrium surface energies reported from experiment, each was consistent with one of these conditions. Furthermore, future computational investigations that rely on accurate surface energy values should consider the surface state of the system and select the appropriate force field.

36 MATERIALS SCIENCE↗

Dosimetric characterization and output verification for conical brachytherapy surface applicators. Part II. High dose rate {sup 192}Ir sources

Purpose: Historically, treatment of malignant surface lesions has been achieved with linear accelerator based electron beams or superficial x-ray beams. Recent developments in the field of brachytherapy now allow for the treatment of surface lesions with specialized conical applicators placed directly on the lesion. Applicators are available for use with high dose rate (HDR){sup 192}Ir sources, as well as electronic brachytherapy sources. Part I of this paper discussed the applicators used with electronic brachytherapy sources. Part II will discuss those used with HDR {sup 192}Ir sources. Although the use of these applicators has gained in popularity, the dosimetric characteristics have not been independently verified. Additionally, there is no recognized method of output verification for quality assurance procedures with applicators like these. Methods: This work aims to create a cohesive method of output verification that can be used to determine the dose at the treatment surface as part of a quality assurance/commissioning process for surface applicators used with HDR electronic brachytherapy sources (Part I) and{sup 192}Ir sources (Part II). Air-kerma rate measurements for the {sup 192}Ir sources were completed with several models of small-volume ionization chambers to obtain an air-kerma rate at the treatment surface for each applicator. Correction factors were calculated using MCNP5 and EGSnrc Monte Carlo codes in order to determine an applicator-specific absorbed dose to water at the treatment surface from the measured air-kerma rate. Additionally, relative dose measurements of the surface dose distributions and characteristic depth dose curves were completed in-phantom. Results: Theoretical dose distributions and depth dose curves were generated for each applicator and agreed well with the measured values. A method of output verification was created that allows users to determine the applicator-specific dose to water at the treatment surface based on a measured air-kerma rate. Conclusions: The novel output verification methods described in this work will reduce uncertainties in dose delivery for treatments with these kinds of surface applicators, ultimately improving patient care.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Quantifying the Impacts of Land Surface Modeling on Hub-Height Wind Speed under Different Soil Conditions

We investigate the impact of three land surface models (LSMs) on hub-height wind speed under three different soil regimes (dry, wet, and frozen) to understand and improve the physics of wind energy forecasts using the Weather Research and Forecasting (WRF) model. A six-day representative period is selected for each soil condition. The simulated wind speed, surface energy budget and soil properties are compared with the observations collected from the second Wind Forecast Improvement Project (WFIP2). For the selected cases, our simulation results suggest that, the impact of LSMs on hub-height wind speed are sensitive to the soil states but not so much to the choice of LSM. The simulated hub-height wind speed is in much better agreement with the observations for the dry soil case than the wet and frozen soil cases. Over the dry soil, there is a strong physical connection between the land surface and hub-height wind speed through near-surface turbulent mixing. Over the wet soil, the simulated hub-height wind speed is less impacted by land surface due to weaker surface fluxes and more dominated by large-scale synoptic disturbances. Over the frozen soil, the land surface model seems to have limited impact on hub-height wind speed variability due to the decoupling of the land surface with the overlying atmosphere. Two main sources of modeling uncertainties are proposed. The first are the insufficient model physics representing the surface energy budget, especially the ground heat flux, and the second are the inaccurate initial soil states such as soil temperature and soil moisture.

Xia, Geng↗

Fast MAS 1 H NMR Study of Water Adsorption and Dissociation on the (100) Surface of Ceria Nanocubes: A Fully Hydroxylated, Hydrophobic Ceria Surface

1 H nuclear magnetic resonance (NMR) spectroscopy was used to study hydroxylic surface species on ceria nanocubes, a crystalline, high-surface-area CeO 2 that presents mostly (100) facets. Water adsorption and desorption experiments in combination with fast magic angle spinning (MAS, 20–40 kHz) 1H NMR provide high-resolution 1 H spectra that allow the observation of ten resonance bands (water or hydroxyl) on or under the (100) surface. Assignments were made using a combination of adsorption and temperature-programmed desorption, quantitative spin counting, deuterium exchange, spin–lattice (T 1 ) and spin–spin (T 2 ) relaxation, and DFT calculations. In air, the (100) surface exists as a fully hydroxylated surface. Water adsorption and dissociation on dry ceria surfaces occur first at oxygen vacancies, but Ce 3+ centers are not required since water dissociation is barrier-less on the fully oxidized surface. Surface $-$OH functionality occurs in two resolved bands representing isolated $-$OH (1 ppm) and hydrogen-bonded $-$OH (9 ppm), the latter being dominant. Deuterium exchange of surface hydroxyls with D 2 O does not occur under mild or forcing conditions. Despite large differences in the T 1 of surface hydroxyls and physisorbed water, surface hydroxyl T 1 values are independent of the presence or absence of physisorbed water, demonstrating that the protons within these two functional group pools are not in intimate contact. These observations show that, once hydroxylated, the surface $-$OH functionality preferentially forms hydrogen bonds with surface lattice oxygen, i.e., the hydroxylated (100) surface of ceria is hydrophobic. Near this surface it is energetically more favorable for physisorbed water to hydrogen bond to itself rather than to the surface. DFT calculations support this notion. Impurity Na + remaining in incompletely washed ceria nanocubes increases the surface hydrophilicity. In conclusion, sharp, low-field resonances observed in spectra of noncalcined nanocubes arise from kinetically trapped subsurface $-$OH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Charging properties of cassiterite (alfa-SnO2) surfaces

The acid-base properties of cassiterite (alfa-SnO2) surfaces at 10 50 C were studied using potentiometric titrations of powder suspensions in aqueous NaCl and RbCl media. The proton sorption isotherms exhibited common intersection points in the pH-range 4.0 to 4.5 at all conditions and the magnitude of charging was similar but not identical in NaCl and RbCl. The hydrogen bonding configuration at the oxide-water interface, obtained from classical Molecular Dynamics (MD) simulations, was analyzed in detail and the results were explicitly incorporated in calculations of protonation constants for the reactive surface sites using the revised MUSIC model. The calculations indicated that the terminal SnOH2 group is more acidic than the bridging Sn2OH group, with protonation constants (log KH) of 3.60 and 5.13 at 25 C, respectively. This is contrary to the situation on the isostructural alfa-TiO2 (rutile), apparently due to the difference in electronegativity between Ti and Sn. MD simulations and speciation calculations indicated considerable differences in the speciation of Na+ and Rb+, despite the similarities in overall charging. Adsorbed sodium ions are almost exclusively found in bidentate surface complexes, while adsorbed rubidium ions form comparable amounts of bidentate and tetradentate complexes. Also, the distribution of adsorbed Na+ between the different complexes shows a considerable dependence on surface charge density (pH), while the distribution of adsorbed Rb+ is almost independent of pH. A Surface Complexation Model (SCM) capable of accurately describing both the measured surface charge and the MD predicted speciation of adsorbed Na+/Rb+ was formulated. According to the SCM, the deprotonated terminal group (SnOH-0.40) and the protonated bridging group (Sn2OH+0.36) dominate the surface speciation over the entire pH-range (2.7 10), illustrating the ability of positively and negatively charged surface groups to coexist. Complexation of the medium cations increases significantly with increasing negative surface charge and at pH 10 roughly 40 percent of the terminal sites are predicted to form cation complexes, while anion complexation is minor throughout the studied pH-range.

Rosenqvist, Jorgen K↗

Ion Beam Analysis Of Silicon-Based Surfaces And Correlation With Surface Energy Measurements

The water affinity of Si-based surfaces is quantified by contact angle measurement and surface free energy to explain hydrophobic or hydrophilic behavior of silicone, silicates, and silicon surfaces. Surface defects such as dangling bonds, surface free energy including Lewis acid-base and Lifshitz-van der Waals components are discussed. Water nucleation and condensation is further explained by surface topography. Tapping mode atomic force microscopy (TMAFM) provides statistical analysis of the topography of these Si-based surfaces. The correlation of the above two characteristics describes the behavior of water condensation at Si-based surfaces. Surface root mean square roughness increasing from several A ring to several nm is found to provide nucleation sites that expedite water condensation visibly for silica and silicone. Hydrophilic surfaces have a condensation pattern that forms puddles of water while hydrophobic surfaces form water beads. Polymer adsorption on these surfaces alters the water affinity as well as the surface topography, and therefore controls condensation on Si-based surfaces including silicone intraocular lens (IOL). The polymer film is characterized by Rutherford backscattering spectrometry (RBS) in conjunction with 4.265 MeV {sup 12}C({alpha}, {alpha}){sup 12}C, 3.045 MeV {sup 16}O({alpha},{alpha}){sup 16}O nuclear resonance scattering (NRS), and 2.8 MeV elastic recoil detection (ERD) of hydrogen for high resolution composition and areal density measurements. The areal density of hydroxypropyl methylcellulose (HPMC) film ranges from 10{sup 18} atom/cm{sup 2} to 10{sup 19} atom/cm{sup 2} gives the silica or silicone surface a roughness of several A ring and a wavelength of 0.16{+-}0.02 {mu}m, and prevents fogging by forming a complete wetting layer during water condensation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Surface stability and the selection rules of substrate orientation for optimal growth of epitaxial II-VI semiconductors

The surface structures of ionic zinc-blende CdTe (001), (110), (111), and (211) surfaces are systematically studied by first-principles density functional calculations. Based on the surface structures and surface energies, we identify the detrimental twinning appearing in molecular beam epitaxy (MBE) growth of II-VI compounds as the (111) lamellar twin boundaries. To avoid the appearance of twinning in MBE growth, we propose the following selection rules for choosing optimal substrate orientations: (1) the surface should be nonpolar so that there is no large surface reconstructions that could act as a nucleation center and promote the formation of twins; (2) the surface structure should have low symmetry so that there are no multiple equivalent directions for growth. These straightforward rules, in consistent with experimental observations, provide guidelines for selecting proper substrates for high-quality MBE growth of II-VI compounds.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Low-index surface energies, cleavage energies, and surface relaxations for crystalline NiAl from first-principles calculations

NiAl surfaces frequently serve as a platform for studying a broad range of physical and chemical phenomena including chemisorption, catalysis, oxidation, alloy growth, and surface nanostructure formation. Knowledge of precise values for low-index surface energies of NiAl, the most fundamental quantities characterizing surface thermodynamics, is often invaluable for understanding of these phenomena. In all previous analyses for NiAl(100) and NiAl(111), Ni- and Al-terminations are not distinguished, and half of the cleavage energy (or equivalently, the average of the surface energies of two differently terminated surfaces) is always identified as the “surface energy”. No values are available for individual surface energies of Ni- or Al-terminated NiAl(100) or NiAl(111) surfaces, whereas knowledge of only cleavage energy is often insufficient for analyzing surface-associated behavior. As such, in this work we perform extensive first-principles density-functional-theory (DFT) calculations for surface energies and cleavage energies of NiAl(110), NiAl(100) and NiAl(111) by considering the chemical-potential-based formulations to clarify the ambiguity in their surface energies and cleavage energies. We obtain a surface-energy phase diagram for these three low-index surfaces versus the relevant chemical potential, as well as the chemical-potential-dependent Wulff plots for NiAl crystal equilibrium shapes. We also provide the surface-relaxation information from our DFT calculations for comparison with previous experimental data.

42 ENGINEERING↗

Improving Land Surface Temperature Simulation in CoLM Over the Tibetan Plateau through Fractional Vegetation Cover Derived from a Remotely Sensed Clumping Index and Model-Simulated Leaf Area Index

Parameterizations of fractional vegetation cover (FVC) in land surface models have important effects on simulations of surface energy budget, especially in arid and semiarid regions. This study uses a FVC scheme in which FVC is derived from leaf area index and a remotely sensed clumping index. The performance of the new scheme (SMFVC) is evaluated against Moderate Resolution Imaging Spectroradiometer (MODIS) land surface temperature (LST) and in situ soil temperature observations, together with two other FVC schemes, a general FVC scheme (CTL) based on land cover map and a climatology-based FVC scheme (RSFVC) that uses long-term remotely sensed Normalized Difference Vegetation Index of MODIS. The three FVC schemes were implemented in the Common Land Model (CoLM) and applied in the Tibetan Plateau using the same forcing data and default parameters. Our results demonstrate that FVC schemes have significant influence on the CoLM performance: (1) the RSFVC and SMFVC schemes significantly reduce the LST biases found in CTL, particularly in grassland and during summer; (2) soil temperature evaluation by in situ observations from three networks on the Tibetan Plateau corroborates the LST results; and (3) the improvements are mainly related to representing temporal (seasonal) variability and subgrid heterogeneity of FVC, which improves surface albedo and surface energy balance. In other words, by including more vegetation characteristics, such as using a clumping index, land surface models may better simulate surface vegetation condition and further better represent the land surface energy budget over the Tibetan Plateau.

Li, Chengwei↗

The impact of surface composition on the interfacial energetics and photoelectrochemical properties of BiVO{sub 4}.

The ability to engineer a photoelectrode surface is pivotal for optimizing the properties of any photoelectrode used for solar fuel production. Altering crystal facets exposed on the surface of photoelectrodes has been a major strategy to modify their surface structure. However, there exist numerous ways to terminate the surface even for the same facet, which can considerably alter the photoelectrode properties. Here we report tightly integrated experimental and computational investigations of epitaxial BiVO4 photoelectrodes with vanadium- and bismuth-rich (010) facets. Our study demonstrates that even for the same facet the surface Bi:V ratio has a remarkable impact on the interfacial energetics and photoelectrochemical properties. We also elucidate the microscopic origins of how the surface composition can affect the photoelectrochemical properties. This study opens an unexplored path for understanding and engineering surface energetics via tuning the surface termination/composition of multinary oxide photoelectrodes.

Lee, Dongho↗

Polar catastrophe and the structure of KT a 1 - x N b x O 3 surfaces: Results from elastic and inelastic helium atom scattering

In this paper, the structure and dynamics of cleaved (001) surfaces of potassium tantalates doped with niobium, KTa 1-x Nb x O 3 (KTN), with x ranging from 0% to 30%, were measured by helium atom scattering (HAS). Through HAS time-of-flight (TOF) experiments, a dispersionless branch (Einstein phonon branch) with energy of 13-14meV was observed across the surface Brillouin zone in all samples. When this observation is combined with the results from earlier experimental and theoretical studies on these materials, a consistent picture of the stable surface structure emerges: After cleaving the single-crystal sample, the surface should be composed of equal areas of KO and TaO 2 /NbO 2 terraces. The data, however, suggest that K + and O 2- ions migrate from the bulk to the surface, forming a charged KO lattice that is neutralized primarily by additional K + ions bridging pairs of surface oxygens. This structural and dynamic modification at the (001) surface of KTN appears due to its formally charged KO(-1) and TaO 2 /NbO 2 (+1) layers and avoids a “polar catastrophe.” Finally, this behavior is contrasted with the (001) surface behavior of the fluoride perovskite KMnF 3 with its electrically neutral KF and MnF 2 layers.

36 MATERIALS SCIENCE↗

Effects of surface initial condition on aqueous corrosion of glass-A study with a model nuclear waste glass

Being a nonequilibrium material, the structure of glass varies with the sample history. Thus, the initial surface condition of a glass can vary with the preparation condition and have a large impact on its reactivity. This paper shows that the aqueous corrosion behavior of international simple glass (ISG) varies depending on the initial surface state. The ISG glass samples were prepared as-polished-only and polished-then-annealed and they were immersed in aqueous solution saturated with soluble SiO 2 at 30°C (modeling a mild condition) and at 90°C (modeling a severe condition). Molecular dynamics simulations were performed to obtain coordination numbers of network formers of ISG to assist oxygen speciation calculations. The surface structures of as-prepared and corroded ISG samples were analyzed using various imaging and spectroscopic techniques. Among these analyses, only the oxygen speciation with x-ray photoelectron spectroscopy showed discernable differences between two uncorroded surfaces with different preparation histories; all other methods could not differentiate the surface preparation history before aqueous corrosion. Such minor difference in chemical structures was found to have a profound impact on corrosion behaviors in the mild condition. In the harsh condition, the surface history dependence was not as drastic as the corrosion in the mild condition. The analysis results of the corroded surfaces suggested that the thickness and structure of the alteration layer formed on ISG in aqueous corrosion can vary with the initial surface state.

nuclear, defects, corrosion↗

Surface Temperature Effect on Convective Heat Transfer Coefficients for Jet Impingement Cooling of Electric Machines with Automatic Transmission Fluid: Preprint

In this study, the results of NREL's continued work on experimental characterization of the thermal performance of free-surface jets of automatic transmission fluid impinged on a heated target surface are presented. The measured heat transfer coefficients are useful for understanding factors influencing performance of driveline fluid-based cooling systems for electric machines and help designers in developing high-performance, power-dense and reliable machines. Experiments were carried out for different fluid and target surface temperatures (50 degrees C, 70 degrees C, and 90 degrees C for the fluid and 90 degrees C, 100 degrees C, 110 degrees C, and 120 degrees C for the target surface). Impinging jet velocities (0.5 m/s to 7.5 m/s) and the jet position on the target surface (center versus edge) were also varied. The impinging angle was kept at 90 degrees relative to the target surface. It was found that higher target surface temperature increased heat transfer coefficients, namely, increasing surface temperature from 90 degrees C to 120 degrees C enhanced heat transfer coefficient values at higher impinged jet velocities (7.5 m/s) by up to 15%.

33 ADVANCED PROPULSION SYSTEMS↗

Fermi surface volume of interacting systems

Three Fermion sumrules for interacting systems are derived at T=0, involving the number expectation N-bar (μ), canonical chemical potentials μ(m), a logarithmic time derivative of the Greens function γ{sub k-vector σ} and the static Greens function. In essence we establish at zero temperature the sumrules linking: N-bar (μ)↔∑{sub m}Θ(μ−μ(m))↔∑{sub k-vector ,σ}Θ(γ{sub k-vector σ})↔∑{sub k-vector ,σ}Θ(G{sub σ}( k-vector ,0)). Connecting them across leads to the Luttinger and Ward sumrule, originally proved perturbatively for Fermi liquids. Our sumrules are nonperturbative in character and valid in a considerably broader setting that additionally includes non-canonical Fermions and Tomonaga–Luttinger models. Generalizations are given for singlet-paired superconductors, where one of the sumrules requires a testable assumption of particle–hole symmetry at all couplings. The sumrules are found by requiring a continuous evolution from the Fermi gas, and by assuming a monotonic increase of μ(m) with particle number m. At finite T a pseudo-Fermi surface, accessible to angle resolved photoemission, is defined using the zero crossings of the first frequency moment of a weighted spectral function.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Elucidation of the surface characteristics and electrochemistry of high-performance LiNiO 2

Phase pure LiNiO 2 was prepared using a solid-state method and the optimal synthesis conditions led to a remarkably high capacity of 200 mA h g $-$1 with excellent retention. The combination of bulk and surface characterization elucidated an essential role of the excess Li in phase formation during synthesis and the subsequent electrochemical performance.

25 ENERGY STORAGE↗