Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL SURFACES, HORIZONTAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Aerodynamic Characteristics of a Canard and an Outboard-Tail Airplane Model at High Subsonic Speeds

An investigation has been made in the Langley high-speed 7- by 10-foot tunnel through a range of Mach numbers from 0.60 to 0.95 of the static longitudinal and lateral stability and control characteristics of a canard airplane configuration and an outboard-tail configuration. The canard model had a twisted wing with approximately 67 deg of sweepback and an aspect ratio of 2.91 and was tested with three trapezoidal canard surfaces having ratios of exposed area to wing area of 0.032, 0.076, and 0.121. The canard model had a single body-mounted vertical tail. The outboard-tail model had its horizontal- and vertical-tail surfaces mounted on slender bodies attached to the wing tips and located to the rear and outboard of the 67 deg sweptback wing of aspect ratio 1.00. The data, which are presented with limited analysis, provide information at high subsonic speeds on these two types of high-speed airplanes which have previously been tested at supersonic speeds and reported in NACA RM L58BO7 and NACA RM L58E20.

Fournier, Paul G.↗
NASA NTRS2018

Tri-Rotor Aircraft Capable of Vertical Takeoff and Landing and Transitioning to Forward Flight

Systems, methods, and devices provide a vehicle, such as an aircraft, with rotors configured to function as a tri-copter for vertical takeoff and landing ("VTOL") and a fixed-wing vehicle for forward flight. One rotor may be mounted at a front of the vehicle fuselage on a hinged structure controlled by an actuator to tilt from horizontal to vertical positions. Two additional rotors may be mounted on the horizontal surface of the vehicle tail structure with rotor axes oriented vertically to the fuselage. For forward flight of the vehicle, the front rotor may be rotated down such that the front rotor axis may be oriented horizontally along the fuselage and the front rotor may act as a propeller. For vertical flight, the front rotor may be rotated up such that the front rotor axis may be oriented vertically to the fuselage, while the tail rotors may be activated.

North, David D.↗
NASA NTRS1982

Effect of nozzle and vertical-tail variables on the performance of a 3-surface F-15 model at transonic Mach numbers

An investigation was conducted in the Langley 16 foot transonic tunnel to determine the longitudinal aerodynamic characteristics of twin two dimensional nozzles and twin baseline axisymmetric nozzles installed on a fully metric 0.047 scale model of the F-15 three surface configuration (canards, wing, horizontal tails). The effects on performance of two dimensional nozzle in flight thrust reversing, locations and orientation of the vertical tails, and deflections of the horizontal tails were also determined. Test data were obtained at static conditions and at Mach numbers from 0.60 to 1.20 over an angle of attack range from -2 deg to 15 deg. Nozzle pressure ratio was varied from jet off to about 6.5.

Pendergraft, O. C., Jr.↗
NASA NTRS1930

Flight Tests on U.S.S. Los Angeles. Part I : Full Scale Pressure Distribution Investigation

The primary purpose of this investigation was to obtain simultaneous data on the loads and stress experience in flight by the U. S. S. Los Angeles which could be used in rigid airship structure design. A secondary object of the investigation was to determine the turning and drag characteristics of the airship. The aerodynamic loading was obtained by measuring the pressure at 95 locations on the tail surfaces, 54 on the hull, and 5 on the passenger car. These measurements were made during a series of maneuvers consisting of turns and reversals in smooth air and during a cruise in rough air which was just short of squall proportions. The results of the pressure measurements on the hull indicate that the forces on the forebody of an airship are relatively small. The tail surface measurements show conclusively that the forces caused by gusts are much greater than those caused by horizontal maneuvers. In this investigation the tail surface loadings caused by gusts closely approached the designed loads of the tail structure. The turning and drag characteristics will be reported in separate reports.

De France, S J↗
NASA NTRS2018

Nozzle Plume/Shock Interaction Experimental and Computational Sonic Boom Analyses from the NASA Ames 9- by 7-Foot Supersonic Wind Tunnel

A wind tunnel test and a computational study were conducted to investigate the complex interactions between a supersonic nozzle plume and shock waves of differing strengths generated from various aft surfaces typical of supersonic aircraft. These analytically-defined aft surfaces were representative of horizontal tails of various sizes, and an aft deck. CFD simulations of many proposed model configurations allowed for assessments of the detailed flow interactions of components in close proximity to the nozzle, as well as assessments of the nozzle jet flow itself. The evaluation of the computational results for many candidate configurations guided the design of model components. The interactions of the waveforms from these surfaces with the jet exhaust plume can have significant adverse effects on the loudness of the sonic boom if the surfaces are not carefully integrated into an aircraft design. The greatest discrepancy in estimating sonic boom loudness for low-boom flight vehicles is currently in predicting the signatures from the aft part of an aircraft, including the interactions with the plume flow. The objectives of this test were to gain a better understanding of these interactions, and to provide a detailed experimental database from multiple sources for use as validation cases for CFD tool development. The subject test was run in the NASA Ames 9- by 7-Ft Supersonic Wind Tunnel in February 2016 at Mach numbers of 1.6 and 2.0, and was funded by the NASA Commercial Supersonics Technology (CST) Project. The nozzle flow was provided by high-pressure air (HPA) pumped through the model, and pressure signature data were acquired with the NASA 14-inch sonic boom pressure rail. The rail measured the locations of the shocks and expansions at various distances and off-track angles from the model. This enabled the impact of the nozzle plume/shock interactions on the near- and mid-field sonic boom pressure waveforms to be quantified. Schlieren images of the flow field around and behind the model were obtained with an RBOS (Retroreflective Background-Oriented Schlieren) technique to determine the origins of the shock and expansion waves, to identify the shape and boundaries of the plume, and to determine the changes in incoming and exiting waveforms within the plume. A total pressure rake was positioned closely behind the model nozzle in order to measure the total pressure profiles of the flow above, within, and below the nozzle exhaust. Model angles and positions in the tunnel were measured by photogrammetry using two cameras since the lack of a model force balance prevented the measurement of model deflections under load.Navier-Stokes computations using two different CFD codes were compared to the experimental sonic boom pressure signature data, and the rake total pressure data in the plume. A computational schlieren technique was used to compare the computed flow field with the RBOS images. The computational results were also used to complement the test data with flow field quantities that could not be measured, such as Mach number and pressure distributions to distinguish shock waves and expansion waves.

sonic boom↗
NASA NTRS1974

Subsonic and supersonic longitudinal stability and control characteristics of an aft tail fighter configuration with cambered and uncambered wings and uncambered fuselage

An investigation has been made in the Mach number range from 0.20 to 2.16 to determine the longitudinal aerodynamic characteristics of a fighter airplane concept. The configuration concept employs a single fixed geometry inlet, a 50 deg leading-edge-angle clipped-arrow wing, a single large vertical tail, and low horizontal tails. The wing camber surface was optimized in drag due to lift and was designed to be self-trimming at Mach 1.40 and at a lift coefficient of 0.20. An uncambered or flat wing of the same planform and thickness ratio was also tested. However, for the present investigation, the fuselage was not cambered. Further tests should be made on a cambered fuselage version, which attempts to preserve the optimum wing loading on that part of the theoretical wing enclosed by the fuselage.

Dollyhigh, S. M.↗
NASA NTRS1993

The airplane: A simulated commercial air transportation study

The 'Airplane' is a moderate-range, 70 passenger aircraft. It is designed to serve demands for flights up to 10,000 feet and it cruises at 32 ft/s. The major drivers for the design of the Airplane are economic competitiveness, takeoff performance, and weight minimization. The Airplane is propelled by a single Astro 15 electric motor and a Zinger 12-8 propeller. The wing section is a Spica airfoil which, because of its flat bottom, provides simplicity in manufacturing and thus helps to cut costs. The wing is constructed of a single load bearing mainspar and shape-holding ribs coated with Monokote skin, lending to a light weight structural makeup. The fuselage houses the motor, flight deck and passenger compartments as well as the fuel and control actuating systems. The wing will be attached to the top of the fuselage as will the fuel and control actuator systems for easy disassembly and maintenance. The aircraft is maneuvered about its pitch axis by means of an aft elevator on the flat plate horizontal tail. The twin vertical tail surfaces are also flat plates and each features a rudder for both directional and roll control. Along with wing dihedral, the rudders will be used to roll the aircraft. The Airplane is less costly to operate at its own maximum range and capacity as well as at its maximum range and the HB-40's maximum capacity than the HB-40.

Dauteuil, Mark↗
NASA NTRS2007

Plans and Status of Wind-Tunnel Testing Employing an Aeroservoelastic Semispan Model

This paper presents the research objectives, summarizes the pre-wind-tunnel-test experimental results to date, summarizes the analytical predictions to date, and outlines the wind-tunnel-test plans for an aeroservoelastic semispan wind-tunnel model. The model is referred to as the Supersonic Semispan Transport (S4T) Active Controls Testbed (ACT) and is based on a supersonic cruise configuration. The model has three hydraulically-actuated surfaces (all-movable horizontal tail, all-movable ride control vane, and aileron) for active controls. The model is instrumented with accelerometers, unsteady pressure transducers, and strain gages and will be mounted on a 5-component sidewall balance. The model will be tested twice in the Langley Transonic Dynamics Tunnel (TDT). The first entry will be an "open-loop" model-characterization test; the second entry will be a "closed-loop" test during which active flutter suppression, gust load alleviation and ride quality control experiments will be conducted.

Perry, Boyd, III↗
NASA NTRS2011

Pressure-Sensitive Paint Measurements on the NASA Common Research Model in the NASA 11-ft Transonic Wind Tunnel

The luminescence lifetime technique was used to make pressure-sensitive paint (PSP) measurements on a 2.7% Common Research Model in the NASA Ames 11ft Transonic Wind Tunnel. PSP data were obtained on the upper and lower surfaces of the wing and horizontal tail, as well as one side of the fuselage. Data were taken for several model attitudes of interest at Mach numbers between 0.70 and 0.87. Image data were mapped onto a three-dimensional surface grid suitable both for comparison with CFD and for integration of pressures to determine loads. Luminescence lifetime measurements were made using strobed LED (light-emitting diode) lamps to illuminate the PSP and fast-framing interline transfer cameras to acquire the PSP emission.

Bell, James H.↗
NASA NTRS1991

The FM-007: An advanced jet commuter for HUB to spoke transportation

Due to the increasing need for new commuter aircraft, the FM-007 is proposed, a technologically advanced jet propelled short takeoff and landing (STOL) airplane. The proposed commuter is designed for hub to spoke air travel. In order to reduce drag, natural laminar flow technology is integrated into the design using the natural laminar flow airfoil section for the wing. A three lifting surface configuration provides for more efficient cruise flight. This unique design includes a small forward wing (canard), a rear mounted high aspect ratio main wing, and a small horizontal stabilizer high atop the vertical tail. These three surfaces act together to reduce drag by minimizing the downward force the horizontal stabilizer has to account for due to the nose down pitching moment. Commuter aircraft must also incorporate passenger comfort. This is achieved by providing a spacious pressurized cabin with a large galley and reduced cabin noise due to incorporation of noise reduction gear. A basic oval design is adopted, as opposed to a circular design in order to allow for the seating of five passengers abreast. To get STOL capability, an over the wing blown flap is used using a Rolls Royce Tay series engine.

Blouke, Peter Scott↗
NASA NTRS1981

Effect of simulated in-flight thrust reversing on vertical-tail loads of F-18 and F-15 airplane models

Investigations were conducted in the Langley 16-Foot Transonic Tunnel to provide data on a 0.10-scale model of the prototype F-18 airplane and a 0.047-scale model of the F-15 three-surface configuration (canard, wing, and horizontal tails). Test data were obtained at static conditions and at Mach numbers from 0.6 to 1.2 over an angle-of-attack range from 2 deg to 15 deg. Nozzle pressure ratio was varied from jet off to about 8.0.

Bare, E. A.↗
NASA NTRS1952

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1995

A concept for adaptive performance optimization on commercial transport aircraft

An adaptive control method is presented for the minimization of drag during flight for transport aircraft. The minimization of drag is achieved by taking advantage of the redundant control capability available in the pitch axis, with the horizontal tail used as the primary surface and symmetric deflection of the ailerons and cruise flaps used as additional controls. The additional control surfaces are excited with sinusoidal signals, while the altitude and velocity loops are closed with guidance and control laws. A model of the throttle response as a function of the additional control surfaces is formulated and the parameters in the model are estimated from the sensor measurements using a least squares estimation method. The estimated model is used to determine the minimum drag positions of the control surfaces. The method is presented for the optimization of one and two additional control surfaces. The adaptive control method is extended to optimize rate of climb with the throttle fixed. Simulations that include realistic disturbances are presented, as well as the results of a Monte Carlo simulation analysis that shows the effects of changing the disturbance environment and the excitation signal parameters.

Jackson, Michael R.↗
NASA NTRS1959

Effect of Horizontal-Tail Chord on the Calculated Subsonic Span Loads and Stability Derivatives of Isolated Unswept Tail Assemblies in Sideslip and Steady Roll

Subsonic span loads and the resulting stability derivatives have been calculated using the discrete-horseshoe-vortex method for a systematic series of horizontal tails in combination with a vertical tail of aspect ratio 1.0 in order to provide information on the effect of varying the chord of the horizontal tail for isolated tail assemblies performing sideslip and steady-roll motions. In addition, the effects of horizontal-tail dihedral angle for the sideslip case were obtained. Each tail surface considered had a taper ratio of 0.5 and an unswept quarter-chord line. The investigation covered variations in horizontal-tail chord, horizontal-tail span, and vertical location of the horizontal tail. The span loads and the resulting total stability derivatives as well as the vertical- and horizontal-tail contributions to these tail-assembly derivatives are presented in the figures for the purpose of showing the influence of the geometric variables. The results of this investigation showed trends that were in agreement with the results of previous investigations for variations in horizontal-tail span and vertical location of the horizontal tail. Variations in horizontal-tail chord expressed herein in terms of the root-chord ratio, that is, the ratio of horizontal-tail root chord to vertical-tail root chord, were found to have a pronounced influence on most of the span loads and the resulting stability derivatives. For most of the cases considered, the rate of change of the span load coefficients and the stability derivatives with the root-chord ratio was found to be a maximum for small values of root-chord ratio and to decrease as root-chord ratio increased.

Booth, Katherine W.↗
NASA NTRSDate not supplied

Application of the CATNLF Design Method to a Transonic Transport Empennage Using CDISC

A novel Crossflow Attenuated Natural Laminar Flow (CATNLF) design method has been developed to achieve laminar flow on aircraft empennage at transonic flight conditions. This approach has been applied to the design of a nonlifting vertical tail using CDISC, a knowledgebased aerodynamic design tool developed at the NASA Langley Research Center. A horizontal tail was also designed using an enhanced CATNLF design approach for low-lift components. CDISC was coupled with USM3D-ME, a Navier-Stokes computational fluid dynamics solver. Stability and transition software was used to determine the laminar extent on the surfaces. Results indicate laminar flow can be sustained at midcruise conditions to about x/c=0.40 on the vertical tail and as much as x/c=0.65 on the horizontal tail lower surface. Transonic longitudinal off-design analysis indicates minimal change in the laminar extent. However, nonzero sideslip angles at transonic conditions can cause premature transition relative to the midcruise condition.

Brent W. Pomeroy↗
NASA NTRS1929

Fluttering of the Tail Surfaces of an Airplane and the Means for Its Prevention

The present article, which constitutes a continuation of the work of Von Baumhauer and Konig, will therefore be restricted to the fluttering of the tail surfaces and especially to oscillations of the horizontal empennage. This will also illustrate the characteristics of all other phenomena of fluttering.

TAIL FLUTTER - CAUSES & PREVENTION↗