Search NASA⌕ Search

SEARCH · Search NASA

Results for “TURBOJET ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1951

Full-scale Investigation of Cooling Shroud and Ejector Nozzle for a Turbojet Engine : Afterburner Installation

A full-scale ejector cooling investigation was made on a turbojet engine - afterburner installation in the NACA Lewis altitude wind tunnel. Ejector performance was studied at primary exhaust-gas temperatures from 2700 degrees to 3400 degrees R (corresponding to ejector temperature ratios from 2.0 to 5.0), primary pressure ratios from 1.79 to 3.4, secondary air flows up to 29 percent of the primary gas flow, and for diameter ratios from 1.08 to 1.42 and spacing ratios from 0.04 to 1.16. In addition, variations were made in the primary exhaust-nozzle area. Ejectors with large diameter ratios permit the attainment of high gas flow ratios, but the jet-thrust losses become prohibitive as the spacing ratio is increased from 0 to 0.16. As the ejector diameter is reduced, the obtainable gas-flow ratio and the thrust loss are reduced. Previous results showing that data obtained at a temperature ratio of 1.0 could not be extrapolated to determine ejector performance at high temperature ratios by the application of the temperature ratio factor to the gas-flow ratios are substantiated by the present investigation.

AFTERBURNERS↗
NASA NTRS1948

Theoretical Comparison of Several Methods of Thrust Augmentation for Turbojet Engines

A theoretical investigation has been made of various methods of thrust augmentation for turbojet engines. The method investigated were tail-pipe burning, water injection at the compressor inlet, a combination of tail-pipe burning and water injection, bleedoff in conjunction with water injection at the compressor inlet, and rocket assist. The effect of ratio of augmented-to-normal total liquid consumption, flight conditions, and design compressor pressure ratio on the augmentation produced by each method were determined. A comparison was also made for a given time of operation of the weight of an augmented engine plus fuel and additional liquids to the weight of a standard engine plus fuel producing the same thrust.

Hall, Eldon W.↗
NASA NTRS1953

Preliminary Transient Performance Data on the J73 Turbojet Engine: Altitude, 45,000 Feet - 3

A program was undertaken to determine the J73 turbojet engine compressor stall and surge characteristics and combustor blow-out limits enc ountered during transient engine operation. Data were obtained in the form of oscillograph traces showing the time history of several engi ne parameters with changes in engine fuel flow. The data presented in this report are for step and ramp changes in fuel flow at an altitude of 45,000 feet and flight Mach numbers of 0 and 0.8.

McAulay, John E.↗
NASA NTRS1947

Preliminary Results of Altitude-Wind-Tunnel Investigation of X24C-4B Turbojet Engine. I - Pressure and Temperature Distributions

Pressures and temperatures throughout the X24C-4B turbojet engine are presented in both tabular and graphical forms to show the effect of altitude, flight Mach number, and engine speed on the internal operation of the engine. These data were obtained in the NACA Cleveland altitude wind tunnel at simulated altitudes from 5000 to 45,000 feet, simulated flight Mach numbers from 0.25 to 1.08, and engine speeds from 4000 to 12,500 rpm. Location and detail drawings of the instrumentation installed at seven survey stations in the engine are shown. Application of generalization factors to pressures and temperatures at each measuring station for the range of altitudes investigated showed that the data did not generalize above an altitude of 25,000 feet. Total-pressure distribution at the compressor outlet varied only with change in engine speed. At altitudes above 35,000 feet and engine speeds above 11,000 rpm, the peak temperature at the turbine-outlet annulus moved inward toward the root of the blade, which is undesirable from blade-stress considerations. The temperature levels at the turbine outlet and the exhaust-nozzle outlet were lowered as the Mach number was increased. The static-pressure measurements obtained at each stator stage of the compressor showed a pressure drop through the inlet guide vanes and the first-stage rotor at high engine speeds. The average values measured by the manufacturer's instrumentation werein close agreement with the average values obtained with NACA instrumentation.

Prince, William R.↗
NASA NTRS1953

Preliminary Transient Performance Data on the J73 Turbojet Engine. II - Altitude, 35,000 Feet

A program was undertaken to determine the J73 turbojet engine compressor stall and surge characteristics and combustor blow-out limits encountered during transient engine operation. Data were obtained in the form of oscillograph traces showing the time history of several engine performance parameters with changes in engine fuel flow. The data presented in this report are for step changes in fuel flow at an altitude of 35,000 feet, at flight Mach numbers of 0.3, 0.8, and 1.2, and at several engine-inlet temperatures,

Lubick, Robert J.↗
NASA NTRS1950

Investigation of Effects of Inlet-air Velocity Distortion on Performance of Turbojet Engine

To determine effect of nonuniform inlet-air velocities, a full scale, axial-flow turbojet engine was investigated in Lewis altitude wind tunnel at altitudes from 20,000 to 50,000 feet, 0.21 flight Mach number and corrected engine speeds from 77.3 percent of rated speed to rated speed. Total-pressure variations as large as 103 pounds per square foot in radial direction and 90 pounds per square foot in circumferential direction at 30,000 feet were obtained. With the distortions investigated, net thrust varied between 0.95 and 1.03 of the thrust with uniform inlet-air distribution. Similarly the ratio of specific fuel consumption varied from 1.00 to 1.04. Within the arrange of this investigation the effects of nonuniform inlet velocity were not serious for the engine investigated.

AIR INLETS↗
NASA NTRS1975

Minimization of jet and core noise of a turbojet engine by swirling the exhaust flow

A noise abating improvement for jet engines has been investigated and demonstrated using a full scale turbojet engine which provided the means for significant reductions in jet and core noise with minimal thrust loss. This was accomplished by controlled solid body rotation (swirling) of the flow in the nozzle and jet exhaust. Relatively moderate angles of solid body rotation in the presence of temperature, density, pressure, and velocity gradients were utilized. Of great interest was the finding that significant reductions of sound pressure levels and sound power were obtained with only a small percentage of the total primary mass flow swirling at the exit of the nozzle. Therefore, tradeoffs between noise reduction and engine performance can be optimized to satisfy aircraft performance and federal noise standards with minimal wasted rotational kinetic energy.

Schwartz, I. R.↗
NASA NTRS1947

An Anaylsis of Control Requirements and Control Parameters for Direct-Coupled Turbojet Engines

Requirements of an automatic engine control, as affected by engine characteristics, have been analyzed for a direct-coupled turbojet engine. Control parameters for various conditions of engine operation are discussed. A hypothetical engine control is presented to illustrate the use of these parameters. An adjustable speed governor was found to offer a desirable method of over-all engine control. The selection of a minimum value of fuel flow was found to offer a means of preventing unstable burner operation during steady-state operation. Until satisfactory high-temperature-measuring devices are developed, air-fuel ratio is considered to be a satisfactory acceleration-control parameter for the attainment of the maximum acceleration rates consistent with safe turbine temperatures. No danger of unstable burner operation exists during acceleration if a temperature-limiting acceleration control is assumed to be effective. Deceleration was found to be accompanied by the possibility of burner blow-out even if a minimum fuel-flow control that prevents burner blow-out during steady-state operation is assumed to be effective. Burner blow-out during deceleration may be eliminated by varying the value of minimum fuel flow as a function of compressor-discharge pressure, but in no case should the fuel flow be allowed to fall below the value required for steady-state burner operation.

Novik, David↗
NASA NTRS1973

Performance of an annual combustor designed for a low-cost turbojet engine

Performance tests were conducted on a combustor designed for use in a low-cost turbojet engine. Low-cost features included the use of very inexpensive simplex fuel nozzles and combustor liners of perforated sheet material. Combustion efficiencies at the altitude-cruise and sea-level design points were approximately 94 and 96 percent, respectively. The combustor isothermal total-pressure loss was 8.8 percent at the altitude-cruise-condition diffuser-inlet Mach number of 0.335. The combustor-exit temperature pattern factor was less than 0.3 at the altitude-cruise, sea-level-cruise, and sea-level-static design conditions. The combustor-exit average radial temperature profiles at all conditions were in very good agreement with the design profile. The intense mixing required because of the very high combustor heat-release rate had an adverse effect on ignition capability at altitude windmilling design conditions.

Fear, J. S.↗
NASA NTRS1949

Performance of J33-A-21 and J33-A-23 Turbojet-Engine Compressors with Water Injection

As part of the performance investigation of compressors for the J33 turbojet engine, the A-21 model and the A-23 model with a 17- and a 34-blade impeller were operated with water injection at their respective design equivalent speeds of 11,500 and 11,750 rpm. Inlet conditions of pressure of 14 inches of mercury absolute and of ambient temperature correspond to those of the investigation of these models without water injection. The water-air ratio by weight ranged from 0.05 to 0.06. By the use of water injection, the peak pressure ratio of the A-21 compressor and the A-23 compressor with a 34-blade impeller increased approximately 0.38, whereas that of the A-23 compressor with a 17-blade impeller increased only 0.14. The decrease in maximum efficiency for the three compressors ranged from 0.12 to 0.14. The highest increase in maximum equivalent weight flow of air plus weight flow of water was 10.90 pounds per second obtained with the A-21 compressor. The increase in air weight flow alone was approximately 5.70 pounds per second for the A-21 compressor end the A-23, 17-blade compressor, which exceeded the increase of 3.15 pounds per second for the A-23; 34-blade compressor.

Beede, William L.↗
NASA NTRS1947

Performance Charts for the Turbojet Engine

Charts are presented for computing the thrust, fuel consumption, and other performance values of a turbojet engine for any given set of operating conditions and component efficiencies. The effects of the pressure losses in the inlet duct and combustion chamber, the variation in the physical properties of the gas as it passes through the cycle, and the change in mass flow by the addition of fuel are included. The principle performance charts show the effects of the primary variables and correction charts provide the effects of the secondary variables.

Pinkel, Benjamin↗
NASA NTRS1950

Effect of fuel volatility on altitude starting limits of a turbojet engine

The effect of fuel volatility on altitude starting limits of an axial-flow-compressor-type turbojet engine was investigated using fuels with Reid vapor pressures of 1.1 and 5.4 pounds per square inch. At flight Mach numbers from 0.40 to 0.85, the AN-F-58 fuel allowed consistent windmilling at altitudes 2000 to 8000 feet higher than was obtained with the 1.1-pound Reid vapor pressure fuel. At a flight Mach number of 0.25, ignition could not be established at any altitude with the lower-volatility fuel.

COMBUSTION - IGNITION OF GASES↗
NASA NTRS1951

Altitude Wind Tunnel Investigation of the Performance of Compressor, Combustor, and Turbine Components of Prototype J47D (RX1-1) Turbojet Engine

As a portion of an over-all performance investigation of the prototype J47D (RX-1) turbojet engine, performance of the compressor, combustor, and turbine components has been determined in the Lewis altitude wind tunnel over a range of altitude from 5000 to 55,000 feet and at flight Mach numbers from 0.19 to 0.92. Investigations were conducted with the engine operating on an electronic control schedule and slow with a two-lever control system by which fuel flow and exhaust-nozzle area could be controlled separately. Two combustor configurations were investigated.

ENGINES, TURBO-JET↗
NASA NTRS1951

Dynamics of a turbojet engine considered as a quasi-static system

A determination of the dynamic characteristics of a typical turbojet engine with a centrifugal compressor, a sonic-flow turbine-nozzle diaphragm, and fixed area exhaust nozzle is presented. A generalized equation for transient behavior of the engine was developed; this equation was then verified by calculations using compressor and turbine performance charts extrapolated from equilibrium operating data and by experimental data obtained from an engine operated under transients in fuel flow. The results indicate that a linear differential equation for engine acceleration as a function of fuel flow and engine speed for operation near a steady-state operating condition can be written. The coefficients of this equation can be obtained either from actual transient data or, with a fair degree of accuracy, from the steady-state performance maps of the compressor and turbine, and can be corrected for altitude in the same manner that steady-state performance data are corrected.

Otto, Edward W↗
NASA NTRS1954

Preliminary Altitude Performance Data for the J65-B3 Turbojet Engine at Reynolds Number Indices from 0.2 to 0.8

Altitude performance characteristics of the J65-B3 turbojet engine and its components were obtained at engine-inlet conditions corresponding to Reynolds number indices from 0.2 to 0.8 over a range of corrected engine speeds from 70 to 110 percent of rated speed. Engine operational limits up to an altitude of 75,000 feet together with ignition and windmilling characteristics were also obtained. The engine and component data are presented both in graphical and in tabulated form. The operational characteristics are presented in graphical form.

Braithwaite, W.M.↗