Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Prediction and demonstration of periodic tensile cracking in rate-dependent porous cement

Periodic dilation bands are shown to occur when cylinder-shaped saturated cement specimens are subjected to rapid decompression, with the spacing between the bands scaling as a power law of the decompression time. This behavior is predicted by theory, which is specified to this scenario based on prior work that was more general and applied to compaction. Specifically, the formation of the bands is shown to coincide with periodicity that naturally arises in the effective stress when the material follows a Terzaghi-type consolidation law, although in reverse for dilation and with material deformation described by a rate-dependent viscoplastic law. When strain rate is proportional to effective stress to a power that is greater than one, periodic regions of tensile effective stress arise through the poromechanical fluid-solid coupling. The theoretically-predicted exponent of the resulting power-law relationship between dilation band spacing and unloading time successfully brackets the experimental results, for which it is observed that the exponent is slightly stronger than a square-root relationship (0.28 to 0.67) at testing temperatures of 20 °C and 90 °C. Further, these results demonstrate that rapid-depressurization leads to periodic fracturing that could, on the one hand, be detrimental to the isolation provided by cement used to seal wellbores in the petroleum industry. On the other hand, the dilation bands could also be favorable to production if generated in low-permeability reservoir rocks such as shales that are targeted for petroleum production or granites that are targeted for geothermal energy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

EGS Collab Experiment 3: 4100 Tensile Stimulation and Thermal Circulation Testing

These data and test descriptions are from a set of primarily tensile hydraulic-fracture stimulations in wells E2-TC and E2-TU and a subsequent chilled water circulation test conducted by injecting in well E2-TU on the 4100 level of the Sandford Underground Research Facility (SURF). Stimulations were carried out between April and May of 2022. The thermal circulation test ran semi-continuously from May 19 through August 26, 2022, though chilled water injection began on June 3. More information about the test, rationale, and processing of data is available on the EGS Collab project page, which is linked below.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Micro-tensile Properties of Fueled Irradiated AGR-2 TRISO-coated Particle Buffer, IPyC, and SiC Interlayer Regions

Tristructural isotropic (TRISO) coated nuclear fuel particles are proving to be a versatile fuel form for new reactor designs. Understanding the bounding strength and failure mode of each coating interface is important to both fuel quality evaluation and failure prediction. A mechanism of key significance is failure of the silicon carbide (SiC) layer to retain fission products due to incomplete tearing of the buffer layer. This is a two-step mechanism involving both mechanical failure in the buffer and inner pyrolytic carbon (IPyC) layers and degradation of the SiC layer through palladium silicides at the IPyC-SiC interface. However, the mechanical properties of TRISO particle coating layers have yet to be fully characterized due to the small dimension of TRISO fuel particles and high radioactivity. To investigate this mechanism, in situ micro-tensile properties of the buffer, IPyC, SiC, buffer-IPyC, and IPyC-SiC interlayer regions of fueled TRISO particles have been tested at both as-fabricated and irradiated conditions. Determination of the mechanical properties of these TRISO particle regions will lead to a better understanding of the SiC layer failure mechanism and enable progress towards TRISO fuel qualification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Analysis Of Fracture Location on Tensile Graphite Samples

The main standard for testing the ultimate tensile strength of graphite is ASTM C749. Commercial entities have raised concerns about samples breaking outside of the gauge section, particularly in the radius or head of the sample. When this occurs, the data gathered from the samples is unusable and increases the cost of testing as more samples will need to be machined. This study investigates the locations and frequency of sample breakage for four different grades of graphite using a custom-made measurement scale. The four grades include two fine-grain (2114 and IG-110) and two medium/coarse-grain (NBG-17 and PCEA). Our results show that fine-grain grades are more susceptible to breaking outside the gauge section, with almost 30% of the samples from grade 2114 breaking outside this region. Additionally, the radius being too small causes stress concentrations near the ends of the gauge section resulting in a bimodal distribution of the fracture locations.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced Tensile and Tear Toughness Properties of Thin-Wall Vacuum-Assisted High-Pressure Die-Cast Aural-5 Alloy by Friction Stir Processing

Steadily rising demand for glider weight reduction has driven the development of vacuum-assisted high-pressure die-cast (HPDC) Al-alloys for automotive structural components. Aural-5 is a strontium-modified HPDC alloy utilizing manganese (Mn) to reduce die soldering, eliminating detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. HPDC Aural-5 contains shrinkage porosity, dendrites with Al-Si eutectic colonies, externally solidified crystals (ESCs), shear-band structure, and large second-phase particulates. Porosity, ESCs and large second-phase particles work as crack initiation sites, negatively impacting tensile properties. In this study, friction stir processing (FSP) is employed for microstructural modification of a thin-walled HPDC Aural-5 by eliminating porosity and breaking down dendrites, second-phase particles, eutectic colonies, ESCs and shear-band structures to create wrought microstructure with homogenized particle distribution. Mechanical property characterization indicates ~30% and ~35% enhancement in yield strength and ductility and associated marked effects on ~69% improvement in tear toughness according to the ASTM B871 test.

Friction stir processing, Aural-5, Strength, Tear ↗
DOE OSTI2021

In Situ TEM Tensile Testing of Bicrystals with Tailored Misorientation Angles

Grain boundaries have complex structural features that influence strength, ductility and fracture in metals and alloys. Grain boundary misorientation angle has been identified as a key parameter that controls their mechanical behavior, but the effect of misorientation angle has been challenging to isolate in polycrystalline materials. Here, we describe the use of bicrystal Au thin films made using a rapid melt growth process to study deformation at a single grain boundary. Tensile testing is performed on bicrystals with different misorientation angles using in situ TEM, as well as on a single crystalline sample. Plastic deformation is initiated through dislocation nucleation from free surfaces. Grain boundary sliding is not observed, and failure occurs away from the grain boundary through plastic collapse in all cases. The failure behavior in these nanoscale bicrystals does not appear to depend on the misorientation angle or grain boundary energy but instead has a more complex dependence on sample surface structure and dislocation activity.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Tensile creep properties of NbTaTi and NbTaTiV refractory complex concentrated alloys

Refractory complex concentrated alloys (RCCAs) have emerged as promising candidates for high-temperature structural applications due to their high melting points and potential for exceptional strength, whereas their creep properties remain relatively underexplored. Here, we investigate the tensile creep behavior of NbTaTi and NbTaTiV in high vacuum to elucidate the influence of alloying on creep mechanisms. NbTaTiV exhibits higher creep resistance than NbTaTi, which is attributed to V-induced edge-dislocation-glide-controlled deformation. Microstructural analysis reveals the formation of Ti- and interstitial impurity-rich secondary phases during creep, which enhances the creep resistance without significant embrittlement. Stress exponents (∼3) and activation energies (∼those for vacancy diffusion) align with thermally activated dislocation glide-controlled creep. Despite NbTaTiV surpassing Ni-based superalloys in yield strength at elevated temperatures, its single-phase BCC structure limits creep resistance under engineering-relevant conditions, highlighting the necessity of deliberate secondary phase design to achieve competitive high-temperature performance.

Complex concentrated alloys↗
DOE OSTI2026

Emerging hierarchical dislocation structures: Insights from scanning electron microscopy-electron backscatter diffraction in situ tensile testing and multifractal analysis

Understanding the evolution of dislocation structures during plastic deformation is critical for predicting the mechanical performance of metallic materials. In this work, we applied in situ scanning electron microscopy/electron backscatter diffraction tensile testing combined with multifractal (MF) analysis to assess deformation-induced dislocation structure evolution in solution-annealed 304 L stainless steel, both in its as-received and neutron-irradiated states (5.4 displacements per atom). The analysis of kernel average misorientation patterns revealed the formation of hierarchical dislocation arrangements that exhibit clear MF scaling behavior. Despite pronounced visual differences between nonirradiated and irradiated specimens—most notably, the appearance of dislocation channels after irradiation—the singularity spectra suggest that both conditions give rise to similar underlying hierarchical structures. MF analysis provides a quantitative measure of the spatial complexity and self-organization of dislocation patterns, highlighting the accelerated emergence and evolution of the dislocation structures in irradiated polycrystalline materials, as well as the limitation of their spatial extent. The findings indicate that irradiation not only modifies microstructure but also alters correlation-driven dislocation organization. More generally, they demonstrate that MF analysis is a powerful tool for probing mesoscale deformation mechanisms.

Dislocation structures↗
DOE OSTI2022

The impact of infill percentage and layer height in small-scale material extrusion on porosity and tensile properties

We report material extrusion additive manufacturing is prone to introducing porosity within the structure due to the layer-by-layer construction using elliptical beads of material. This open porosity ultimately plays a role in determining the mechanical properties of printed parts. The shape, size, and amount of porosity within a printed part is influenced by a variety of factors, including nozzle diameter, infill percentage, layer height, raster orientation, and print speed. While several studies have investigated these and other parameters’ effects on mechanical performance and porosity, better understanding the interconnected relationships is crucial in balancing the various input parameters to achieve maximum strength. This work initially examined the influence of key print parameters (infill percentage and layer height) on the internal porosity of a printed Acrylonitrile Butadiene Styrene (ABS) part. Then, the print parameters and internal porosity were statistically correlated to final mechanical properties. Porosity was further classified as either open or closed to differentiate between connected voids in the mesostructure from isolated voids within the material itself. Mechanical performance increased with an increasing density and infill percentage, displaying a 224 % increase in elastic modulus and a 150 % increase in ultimate tensile strength. The contribution of layer height was found to be conditional upon the infill percentage.

3D Printing↗
DOE OSTI2020

The microstructure of a selective laser melting (SLM)-fabricated NiTi shape memory alloy with superior tensile property and shape memory recoverability

A selective laser melting (SLM)-fabricated NiTi with superior tensile property and shape memory recoverability was obtained by using a unique stripe rotation scanning strategy. Here, the alloy characteristics, formation mechanisms and evolution in terms of twins, dislocations and precipitations of the alloy were systematically studied. Compared to the conventional smelting-followed-by-machining, the SLM fabrication process involves rapid solidification and repeated heating, which confer distinctive characteristics to the microstructures of SLM-fabricated NiTi alloys. Rapid solidification promotes the formation of a supersaturation solid solution matrix containing a high concentration vacancies, which in turn aggregate to generate a high density of dislocations. During subsequent repeated heating stages, these dislocations occur thermal motion along three directions of <001 > , <111> and <110 >, leading to the formation of thermal kinks, helical dislocations and wave morphology. Simultaneously, precipitated particles Ti 3 Ni 4 repeatedly nucleate and heterogeneous grow with the movement of dislocation. Such precipitation behavior, termed repeated precipitation, has not been previously reported in the conventional NiTi alloys, suggesting that it could be a unique characteristic of such alloy. After martensitic transformation, only two twins, {1 1¯ 1} type I twin and compound twin, are detected. The twinning lamellae of these two twins, where precipitation and dislocation pile-ups exist, often have uneven thickness and chaotic arrangement. Besides, the unique self-accommodated microstructures, such as secondary {1 1¯ 1} type I twin and compound twin with “herring-bone’’ lamellae, which often appear in the deformed or nanocrystalline NiTi, can also be observed. These unique microstructures may confer the distinctive properties to the SLM-fabricated NiTi.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Influence of stacking fault energy and hydrogen on deformation mechanisms in high Mn austenitic steels during in-situ tensile testing

High Mn austenitic steels are considered an economical alloy system for hydrogen storage and transport applications. This study used stacking fault energy (SFE) as a design parameter to achieve hydrogen embrittlement (HE)-resistant high Mn austenitic alloys. The role of hydrogen on the deformation mechanisms of low (29 mJ/m 2 ) and high SFE (49 mJ/m 2 ) alloys was evaluated through in-situ neutron diffraction during tensile loading. Hydrogen-precharging increased yield strength, partly due to hydrogen-induced lattice distortion (i.e., solute strengthening). Hydrogen accelerated the increase in defect density, including dislocations and stacking faults. The formation of planar deformation structures (twins and stacking faults), relative to dislocations, plays a critical role in promoting hydrogen-assisted fracture. The stacking fault frequency parameter obtained from neutron diffraction quantifies planar deformation tendencies, correlated with HE sensitivity. The higher SFE alloy exhibited greater resistance to HE, associated with the reduced propensity to form stacking faults and twins upon deformation in the hydrogen-precharged condition.

High Mn austenitic steel↗
DOE OSTI2022

Microstructure-refinement–driven enhanced tensile properties of high-pressure die-cast A380 alloy through friction stir processing

This work employs friction stir processing (FSP), a well-known severe plastic deformation technique, to selectively modify the microstructure of thin-walled, high-pressure die-cast (HPDC) aluminum alloy A380, a major HPDC alloy fabricated in the die casting sector. FSP effectively breaks down Al dendrites and acicular Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. After FSP, the refined Si particles (~1.5 µm) are smaller than the eutectic Si particles (3–8 µm) in HPDC condition. In addition, interparticle distance has decreased almost 50% compared to dendritic arm spacing, and FSP has reduced the aspect ratio of Si particles to ~2. Furthermore, FSP eliminates porosity, and breaks down needle-like second-phase Fe-Mn and Cu-rich particles, yielding a refined, homogeneous distribution. The FSP-induced microstructural refinement and porosity reduction improve bulk yield strength and ductility by 23% and 66%. Tensile properties are enhanced beyond those of the die skin of the HPDC plate, and the alloy possesses lower defect density and a highly refined microstructure. This study establishes the viability of FSP as a tool for microstructure modification and mechanical property improvement for HPDC Al alloys for the light-weighting goal of the automotive industries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Insights into elevated temperature tensile deformation mechanisms and kink banding in additively manufactured tungsten

Additive manufacturing (AM) potentially enables fabrication and repair of plasma facing components (PFCs) of tungsten. However, deformation mechanisms in AM-fabricated tungsten under service-relevant thermomechanical conditions remain unknown majorly due to challenges in achieving crack-free W. This study reveals the deformation mechanisms operative under tension at 800 °C and 1200 °C in the electron beam melting powder bed fusion (EBM-PBF) fabricated W. Textured columnar grains with mixed <001 >/<111 >|| build-direction were observed. Strong anisotropy in tensile properties persisted across test temperatures, and all specimens exhibited extensive deformation-induced banding phenomena. Grain boundary character analysis of the deformed specimens indicated that these deformation bands were kink bands with tilt grain boundaries prominently present at the band-matrix interface. Interestingly, the material within the kink bands rotated toward higher resolved shear stress, providing insights into the origins of kink band formation in body-centered cubic refractory metals. Intragranular misorientation axis analysis revealed that plasticity was dominated by {110} <111 > slip at 800 °C, whereas additional (213)[11⁢̄1] and (112)[11⁢̄1] slip systems activated at 1200 °C. A dense low-angle boundary networks observed near fractured surface indicated the onset of dynamic recrystallization. Results reveal plasticity governing mechanisms in AM-fabricated W under power plant-relevant conditions, and provide insights into kink band attributes in refractory metals.

Mayes, Riley [ORNL] (ORCID:000900089307010X)↗
DOE OSTI2020

Notch-tensile behavior of Al0.1CrFeCoNi high entropy alloy

Notch-tensile behavior of an Al0.1CrFeCoNi high entropy alloy (Al0.1-HEA) was studied using V-notch geometry and with local strain mapping using digital image correlation (DIC). A notch-strength ratio of 1.51 indicated notch strengthening. Further analysis of stress-strain response supplemented with microstructural analysis revealed that, while the presence of notch results in strengthening due to work hardening by twinning induced plasticity, the notch also contributes strongly to geometrical softening in the non-uniform ductility regime, and accounts for the onset of failure. The strain localization behavior of Al0.1-HEA due to the presence of V-notch was compared with three conventional alloys: Inconel 625 nickel-based superalloy, 304 stainless steel and Ti–6Al–4V titanium alloy. The study revealed that the nature of notch widening with increasing strain was dependent on material characteristics. The extent of notch widening impacted the local strain field and stress distribution, thereby influencing the propensity for crack initiation and growth. The experimental results were verified by finite element analysis.

Sinha, Subhasis↗
DOE OSTI2022

Correlating dislocation structures to basal and prismatic slip bands near grain boundaries in tensile-tested Mg–4Al using a multiscale electron microscopy approach

Dislocation structures where basal and prismatic slip bands meet grain boundaries in tensile-tested Mg with 4 wt% Al (Mg–4Al) were studied using a multiscale electron microscopy approach to explore the assumptions made for the dislocation pileup theory: a) slip bands consist of dislocation arrays piling up near grain boundaries, and b) stress concentration in the adjacent grain is solely caused by dislocation pileup. After post-testing electron backscatter diffraction (EBSD) scans, focused-ion-beam (FIB) lift-out specimens were prepared from regions of interest so that the specimen plane is parallel to the bulk sample surface to allow for direct correlation between mesoscale and microscale characterization. High dislocation density and the dislocation arrays in the slip bands corroborated with the first assumption. Evidence of plastic deformation in all grains, however, showed that the second assumption was false. Additionally, dislocation structures including crystal rotation boundaries and dislocations dissociating to the basal plane provide additional stress relief mechanisms near grain boundaries that are not accounted for in many crystal plasticity models, which requires auxiliary models to more accurately predict the stress and strain distribution in a microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An additively manufactured AlCuMnZr alloy microstructure and tensile mechanical properties

In this study, selective laser melting (SLM) was used to fabricate an AlCuMnZr alloy. The microstructural features that resulted from additive manufacturing (AM) were significantly refined compared to the corresponding cast alloy features. A combination of fine equiaxed and columnar grains along with in-situ formation of θ' precipitates during AM leads to enhanced yield strength (up to 300°C) in the as-fabricated AM alloy. The refinement of brittle intermetallics and a bimodal grain size distribution leads to improved tensile elongation in the AM alloy. The results illustrate the microstructural advantages that can result from additive processing over conventionally processed microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tensile creep properties of a CrMnFeCoNi high-entropy alloy

Tensile creep tests were performed on a CrMnFeCoNi high-entropy alloy at temperatures from 1023 K to 1173 K. A uniform stress exponent 3.7 ± 0.1 was found across all temperatures. The apparent activation energies of creep under various applied stresses were determined to be around 230 kJ/mol and decrease with increasing stress, indicating a stress-assisted, thermally activated behavior. Steady-state creep microstructures feature no subgrain formation and high dislocation density within grains. Based on our results, the creep rate of CrMnFeCoNi is believed to be controlled by both dislocation-dislocation interactions and dislocation-lattice interactions.

36 MATERIALS SCIENCE↗