Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Accelerated/abbreviated test methods of the low-cost silicon solar array project. Study 4, task 3: Encapsulation

Methods of accelerated and abbreviated testing were developed and applied to solar cell encapsulants. These encapsulants must provide protection for as long as 20 years outdoors at different locations within the United States. Consequently, encapsulants were exposed for increasing periods of time to the inherent climatic variables of temperature, humidity, and solar flux. Property changes in the encapsulants were observed. The goal was to predict long term behavior of encapsulants based upon experimental data obtained over relatively short test periods.

Kolyer, J. M.↗
NASA NTRS1994

Residual flexibility test method for verification of constrained structural models

A method is described for deriving constrained modes and frequencies from a reduced model based on a subset of the free-free modes plus the residual effects of neglected modes. The method involves a simple modification of the MacNeal and Rubin component mode representation to allow development of a verified constrained (fixed-base) structural model. Results for two spaceflight structures having translational boundary degrees of freedom show quick convergence of constrained modes using a measureable number of free-free modes plus the boundary partition of the residual flexibility matrix. This paper presents the free-free residual flexibility approach as an alternative test/analysis method when fixed-base testing proves impractical.

Admire, John R.↗
DOE OSTI2025

Application of pH-dependent environmental protection agency test method 1313 to low-activity nuclear waste glass

Here, in this study, we present results of a room temperature, pH-dependent leach test established by United States Environmental Protection Agency (EPA) Leaching Environmental Assessment Framework (LEAF) (EPA Method 1313 and further abbreviated EPA 1313) to study the alteration behavior of low-activity nuclear waste (LAW) glasses. Implementation of EPA 1313, which is closer to LAW disposal temperatures, could allow for more flexibility in the formulation of Hanford LAW glasses, specifically in terms of increased waste loading. A set of 48 LAW glasses were selected to test with EPA 1313. Briefly, the test method consists of adding glass to a number of solutions at different initial pH values and at a fixed mass-to-solution-volume ratio. The glass is then allowed to corrode for two days and the final solution pH and concentration of different glass elements in solution is measured. The test was modified from the published procedure to constrain particle size to provide more reproducible results, reduce the studied pH range to a more applicable range, and to reduce solution volume to reduce costs associated with material preparation. Compositional modeling was used to predict the measured elemental releases at various pH. The model predictions improved in tests where there was a relatively small difference between initial and final solution pH indicating that pH controls would result in better predictive models.

Accelerated aging↗
NASA NTRS1977

Developments in fracture mechanics test methods standardization; Proceedings of the Symposium, St. Louis, Mo., May 4, 1976

Experience in plane-strain fracture toughness testing per ASTM Method E 399 is considered along with fracture toughness testing using the C-shaped specimen, an analysis of radially cracked ring segments subject to forces and couples, compliance calibration of specimens used in the R-curve practice, heavy-section fracture toughness screening specimen, and sharply notched cylindrical tension specimens for screening plane-strain fracture toughness. Attention is also given to an investigation of some problems in developing standards for precracked Charpy specimen strength ratios, fracture testing with surface crack specimens, and the estimation of plane strain fracture toughness values from slow bend precracked Charpy specimen strength ratios.

Brown, W. F., Jr.↗
NASA NTRS2005

Latency in Visionic Systems: Test Methods and Requirements

A visionics device creates a pictorial representation of the external scene for the pilot. The ultimate objective of these systems may be to electronically generate a form of Visual Meteorological Conditions (VMC) to eliminate weather or time-of-day as an operational constraint and provide enhancement over actual visual conditions where eye-limiting resolution may be a limiting factor. Empirical evidence has shown that the total system delays or latencies including the imaging sensors and display systems, can critically degrade their utility, usability, and acceptability. Definitions and measurement techniques are offered herein as common test and evaluation methods for latency testing in visionics device applications. Based upon available data, very different latency requirements are indicated based upon the piloting task, the role in which the visionics device is used in this task, and the characteristics of the visionics cockpit display device including its resolution, field-of-regard, and field-of-view. The least stringent latency requirements will involve Head-Up Display (HUD) applications, where the visionics imagery provides situational information as a supplement to symbology guidance and command information. Conversely, the visionics system latency requirement for a large field-of-view Head-Worn Display application, providing a Virtual-VMC capability from which the pilot will derive visual guidance, will be the most stringent, having a value as low as 20 msec.

Bailey, Randall E.↗
NASA NTRS1981

Curved-flow, rolling-flow, and oscillatory pure-yawing wind-tunnel test methods for determination of dynamic stability derivatives

The test capabilities of the Stability Wind Tunnel of the Virginia Polytechnic Institute and State University are described, and calibrations for curved and rolling flow techniques are given. Oscillatory snaking tests to determine pure yawing derivatives are considered. Representative aerodynamic data obtained for a current fighter configuration using the curved and rolling flow techniques are presented. The application of dynamic derivatives obtained in such tests to the analysis of airplane motions in general, and to high angle of attack flight conditions in particular, is discussed.

Chambers, J. R.↗
NASA NTRS1989

Strain energy release rate as a function of temperature and preloading history utilizing the edge delamination fatique test method

Static laminate and tension-tension fatigue tests of IM7/8551-7 composite materials was performed. The Edge Delamination Test (EDT) was utilized to evaluate the temperature and preloading history effect on the critical strain energy release rate. Static and fatigue testing was performed at room temperature and 180 F (82 C). Three preloading schemes were used to precondition fatigue test specimens prior to performing the normal tension-tension fatigue EDT testing. Computer software was written to perform all fatigue testing while monitoring the dynamic modulus to detect the onset of delamination and record the test information for later retrieval and reduction.

Zimmerman, Richard S.↗
NASA NTRS1971

Testing methods and techniques: Strength of materials and components. A compilation

The methods, techniques, and devices used in testing the mechanical properties of various materials are presented. Although metals and metal alloys are featured prominently, some of the items describe tests on a variety of other materials, from concrete to plastics. Many of the tests described are modifications of standard testing procedures, intended either to adapt them to different materials and conditions, or to make them more rapid and accurate. In either case, the approaches presented can result in considerable cost savings and improved quality control. The compilation is presented in two sections. The first deals specifically with material strength testing; the second treats the special category of fracture and fatigue testing.

Source record↗
NASA NTRS1991

The Rocketdyne Multifunction Tester. Part 1: Test Method

The Rocketdyne Multifunction Tester is a general purpose test apparatus which utilizes axial and radial magnetic bearings as shaft excitation devices. The tester is modular in design so that different seal and bearing packages can be tested on the same test stand. The tester will be used for rotordynamic coefficient extraction, as well as life and fluid/material compatibility evaluations. Use of a magnetic bearing as a shaft excitation device opens up many possibilities for shaft excitation and rotordynamic coefficient extraction. In addition to describing the basic apparatus, some of the excitation and extraction methods are described. Some of the excitation methods to be discussed include random, aperiodic, harmonic, impulse and chirp.

Murphy, Brian T.↗
NASA NTRS2007

Development of Natural Flaw Samples for Evaluating Nondestructive Testing Methods for Foam Thermal Protection Systems

Low density polyurethane foam has been an important insulation material for space launch vehicles for several decades. The potential for damage from foam breaking away from the NASA External Tank was not realized until the foam impacts on the Columbia Orbiter vehicle caused damage to its Leading Edge thermal protection systems (TPS). Development of improved inspection techniques on the foam TPS is necessary to prevent similar occurrences in the future. Foamed panels with drilled holes for volumetric flaws and Teflon inserts to simulate debonded conditions have been used to evaluate and calibrate nondestructive testing (NDT) methods. Unfortunately the symmetric edges and dissimilar materials used in the preparation of these simulated flaws provide an artificially large signal while very little signal is generated from the actual defects themselves. In other words, the same signal are not generated from the artificial defects in the foam test panels as produced when inspecting natural defect in the ET foam TPS. A project to create more realistic voids similar to what actually occurs during manufacturing operations was began in order to improve detection of critical voids during inspections. This presentation describes approaches taken to create more natural voids in foam TPS in order to provide a more realistic evaluation of what the NDT methods can detect. These flaw creation techniques were developed with both sprayed foam and poured foam used for insulation on the External Tank. Test panels with simulated defects have been used to evaluate NDT methods for the inspection of the External Tank. A comparison of images between natural flaws and machined flaws generated from backscatter x-ray radiography, x-ray laminography, terahertz imaging and millimeter wave imaging show significant differences in identifying defect regions.

Workman, Gary L.↗
NASA NTRS1973

An evaluation of a constrained test method for obtaining free body responses

A method for obtaining free body responses from dynamic tests on a constrained structure is investigated for practical feasibility. The method is based on the principle that a constrained structure can be considered to be a free body acted upon by multiple forces which include the forces of constraint. By measuring these forces and by exciting the structure so as to develop linearly independent sets of forces, the response of the free body to one force at a time can be computed. Techniques for producing these independent forces are discussed. The development of the theory, computer simulations of tests of representative aerospace vehicles (including experimental error), and a description and listing of the computer programs developed are included. The procedure appears to be a practical method for obtaining in-flight characteristics of such vehicles.

Berman, A.↗
NASA NTRS1980

Static pressure orifice system testing method and apparatus

A method and apparatus are presented for pressure testing the static pressure orifices and associated connections used in wind tunnels. A cylindrical module, having in one end an open hemispherical calibration pressure chamber separated from and surrounded by an annular vacuum chamber is placed over the orifice of the system to be tested. O-rings ensure seating and a vacuum seal between the chambered end of the module and the surface around the orifice: one O-ring separates the outer chamber from the outside environment. Ports lead from each of the chambers out the other end of the module to tubes connected to a control box consisting of calibration pressure and vacuum supply lines, bleeder valves, and gauges.

Culotta, R. F.↗
NASA NTRS1938

A New Spinning-test Method

This report contains a description of a new spinning-test arrangement wherein the otherwise customary rotation of the model about a fixed axis is abandoned in favor of a corresponding rotation of the air stream. The advantage of this method lies in the fact that the model is at rest while the spin is recorded. In this manner it is possible to secure systematic results with little loss of time while employing 3- or 6-component wind-tunnel balances. The troublesome equalization of the mass forces is eliminated and the flow phenomena are accessible to direct observation.

Kramer, M↗
NASA NTRS1974

Selection of appropriate test method for simulating steady-state spacecraft launch loads

In ground testing prior to launch the static loads portion of the launch profile may be simulated by either applying static loads directly to the spacecraft through an appropriate loading facility or by subjecting the spacecraft to acceleration loads on a centrifuge. The factors to be considered in selecting one of the two simulation methods are discussed, giving attention to the relative advantages of the two methods in each case.

Shockey, E. F.↗
NASA NTRS2018

Full-Scale Passive Earth Entry Vehicle Landing Tests: Methods and Measurements

During the summer of 2016, a series of drop tests were conducted on two passive earth entry vehicle (EEV) test articles at the Utah Test and Training Range (UTTR). The tests were conducted to evaluate the structural integrity of a realistic EEV vehicle under anticipated landing loads. The test vehicles were lifted to an altitude of approximately 400m via a helicopter and released via release hook into a predesignated 61 m landing zone. Onboard accelerometers were capable of measuring vehicle free flight and impact loads. High-speed cameras on the ground tracked the free-falling vehicles and data was used to calculate critical impact parameters during the final seconds of flight. Additional sets of high definition and ultra-high definition cameras were able to supplement the high-speed data by capturing the release and free flight of the test articles. Three tests were successfully completed and showed that the passive vehicle design was able to withstand the impact loads from nominal and off-nominal impacts at landing velocities of approximately 29 m/s. Two out of three test resulted in off-nominal impacts due to a combination of high winds at altitude and the method used to suspend the vehicle from the helicopter. Both the video and acceleration data captured is examined and discussed. Finally, recommendations for improved release and instrumentation methods are presented.

Littell, Justin D.↗
NASA NTRS1978

An evaluation of the sandwich beam in four-point bending as a compressive test method for composites

The experimental phase of the study included compressive tests on HTS/PMR-15 graphite/polyimide, 2024-T3 aluminum alloy, and 5052 aluminum honeycomb at room temperature, and tensile tests on graphite/polyimide at room temperature, -157 C, and 316 C. Elastic properties and strength data are presented for three laminates. The room temperature elastic properties were generally found to differ in tension and compression with Young's modulus values differing by as much as twenty-six percent. The effect of temperature on modulus and strength was shown to be laminate dependent. A three-dimensional finite element analysis predicted an essentially uniform, uniaxial compressive stress state in the top flange test section of the sandwich beam. In conclusion, the sandwich beam can be used to obtain accurate, reliable Young's modulus and Poisson's ratio data for advanced composites; however, the ultimate compressive stress for some laminates may be influenced by the specimen geometry.

Shuart, M. J.↗
NASA NTRS1992

Residual flexibility test method for verification of constrained structural models

A method is presented for deriving constrained modes and frequencies from a model correlated to a set of free-free test modes and a set of measured residual flexibilities. The method involves a simple modification of the MacNeal and Rubin component mode representation to allow verification of a constrained structural model. Results for two spaceflight structures show quick convergence of constrained modes using an easily measurable set of free-free modes plus the residual flexibility matrix or its boundary partition. This paper further validates the residual flexibility approach as an alternative test/analysis method when fixed-base testing proves impractical.

Admire, John R.↗