SEARCH · Search NASA

Results for “Torque Limiter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Performance Comparisons and Down Selection of Small Motors for Two-Blade Heliogyro Solar Sail 6U CubeSat

This report compiles a review of 130 commercial small scale motors (piezoelectric and electric motors) and almost 20 researched-type small scale piezoelectricmotors for potential use in a 2 blades Heliogyro Solar Sail 6U CubeSat. In this application, a motor and gearhead (drive system) will deploy a roll of solar sailthin film (2 um thick)accommodated in a 2U CubeSat (100 x 200 x 100 mm) housing. The application requirements are: space rated, output torque at fulldeployment of 0.8 Nm, reel speed of 3 rpm, drive system weight limited to 150 grams, diameter limited to 50 mm, and the length not to exceed 40 mm. The 50mm diameter limit was imposed as motors with larger diameters would likely weigh too much and use more space on the satellite wall. This would limit theamount of the payload. The motors performance are compared between small scale, volume within 3x102 cm3 (3x105 mm3), commercial electric DC motors,commercial piezoelectric motors, and researched-type (non-commercial) piezoelectric motors extracted from scientific and product literature. The comparisonssuggest that piezoelectric motors without a gearhead exhibit larger output torque with respect to their volume and weight and require less input power toproduce high torque. A commercially available electric motor plus a gearhead was chosen through a proposed selection process to meet the applications designrequirements.

Wiwattananon, Peerawan↗

NASA NTRS1976

OH-58 helicopter transmission failure analysis

The OH-58 main transmission gearbox was run at varying output torques, speeds, and oil cooling rates. The gearbox was subsequently run to destruction by draining the oil from the gearbox while operating at a speed of 6200 revs per minute and 36,000 inch-pounds output torque. Primary cause of gearbox failure was overheating and melting of the planet bearing aluminum cages. Complete failure of the gearbox occurred in 28 1/2 minutes after the oil pressure dropped to zero. The alternating and maximum stresses in the gearbox top case were approximately 10 percent of the endurance limit for the material. Deflection of the bevel gear at 67000 inch-pounds output torque indicate a marginal stiffness for the bevel gear supporting system.

Townsend, D. P.↗

NASA NTRS1980

Simplified fatigue life analysis for traction drive contacts

A simplified fatigue life analysis for traction drive contacts of arbitrary geometry is presented. The analysis is based on the Lundberg-Palmgren theory used for rolling-element bearings. The effects of torque, element size, speed, contact ellipse ratio, and the influence of traction coefficient are shown. The analysis shows that within the limits of the available traction coefficient, traction contacts exhibit longest life at high speeds. Multiple, load-sharing roller arrangements have an advantageous effect on system life, torque capacity, power-to-weight ratio and size.

Rohn, D. A.↗

NASA NTRS1980

Simplified fatigue life analysis for traction drive contacts

Rohn, D. A.↗

NASA NTRS1995

Dynamic analysis of astronaut motions in microgravity: Applications for Extravehicular Activity (EVA)

Simulations of astronaut motions during extravehicular activity (EVA) tasks were performed using computational multibody dynamics methods. The application of computational dynamic simulation to EVA was prompted by the realization that physical microgravity simulators have inherent limitations: viscosity in neutral buoyancy tanks; friction in air bearing floors; short duration for parabolic aircraft; and inertia and friction in suspension mechanisms. These limitations can mask critical dynamic effects that later cause problems during actual EVA's performed in space. Methods of formulating dynamic equations of motion for multibody systems are discussed with emphasis on Kane's method, which forms the basis of the simulations presented herein. Formulation of the equations of motion for a two degree of freedom arm is presented as an explicit example. The four basic steps in creating the computational simulations were: system description, in which the geometry, mass properties, and interconnection of system bodies are input to the computer; equation formulation based on the system description; inverse kinematics, in which the angles, velocities, and accelerations of joints are calculated for prescribed motion of the endpoint (hand) of the arm; and inverse dynamics, in which joint torques are calculated for a prescribed motion. A graphical animation and data plotting program, EVADS (EVA Dynamics Simulation), was developed and used to analyze the results of the simulations that were performed on a Silicon Graphics Indigo2 computer. EVA tasks involving manipulation of the Spartan 204 free flying astronomy payload, as performed during Space Shuttle mission STS-63 (February 1995), served as the subject for two dynamic simulations. An EVA crewmember was modeled as a seven segment system with an eighth segment representing the massive payload attached to the hand. For both simulations, the initial configuration of the lower body (trunk, upper leg, and lower leg) was a neutral microgravity posture. In the first simulation, the payload was manipulated around a circular trajectory of 0.15 m radius in 10 seconds. It was found that the wrist joint theoretically exceeded its ulnal deviation limit by as much as 49. 8 deg and was required to exert torques as high as 26 N-m to accomplish the task, well in excess of the wrist physiological limit of 12 N-m. The largest torque in the first simulation, 52 N-m, occurred in the ankle joint. To avoid these problems, the second simulation placed the arm in a more comfortable initial position and the radius and speed of the circular trajectory were reduced by half. As a result, the joint angles and torques were reduced to values well within their physiological limits. In particular, the maximum wrist torque for the second simulation was only 3 N-m and the maximum ankle torque was only 6 N-m.

Newman, Dava J.↗

NASA NTRS1977

Rotational joint assembly for the prosthetic leg

A rotational joint assembly for a prosthetic leg has been devised, which enables an artificial foot to rotate slightly when a person is walking, running or turning. The prosthetic leg includes upper and lower tubular members with the rotational joint assembly interposed between them. The assembly includes a restrainer mechanism which consists of a pivotably mounted paddle element. This device applies limiting force to control the rotation of the foot and also restores torque to return the foot back to its initial position.

Owens, L. J.↗

NASA NTRS1978

Subminiature hydraulic actuator

Subminiature, single-vane rotary actuator for wind-tunnel test-model control-surface actuation systems presents severe torque and system band-pass requirements with stringent space and weight limitations. Actuator has very low leakage of fluid from one side to other, permitting use in precision position servo-systems.

Sevart, F. D.↗

NASA NTRS1990

COBE attitude as seen from the FDF

The goal of the Flight Dynamics Facility (FDF) attitude support is twofold: to determine spacecraft attitude and to explain deviations from nominal attitude behavior. Attitude determination often requires resolving contradictions in the sensor observations. This may be accomplished by applying calibration corrections or by revising the observation models. After accounting for all known sources of error, solution accuracy should be limited only by observation and propagation noise. The second half of the goal is to explain why the attitude may not be as originally intended. Reasons for such deviations include sensor or actuator misalignments and control system performance. In these cases, the ability to explain the behavior should, in principle, be limited only by knowledge of the sensor and actuator data and external torques. Documented here are some results obtained to date in support of the Cosmic Background Explorer (COBE). Advantages and shortcomings of the integrated attitude determination/sensor calibration software are discussed. Some preliminary attitude solutions using data from the Diffuse Infrared Background Experiment (DIRBE) instrument are presented and compared to solutions using Sun and Earth sensors. A dynamical model is constructed to illustrate the relative importance of the various sensor imprefections. This model also shows the connection between the high- and low-frequency attitude oscillations.

Sedlak, J.↗

NASA NTRS1995

Disk tides and accretion runaway

It is suggested that tidal interaction of an accreting planetary embryo with the gaseous preplanetary disk may provide a mechanism to breach the so-called runaway limit during the formation of the giant planet cores. The disk tidal torque converts a would-be shepherding object into a 'predator,' which can continue to cannibalize the planetesimal disk. This is more likely to occur in the giant planet region than in the terrestrial zone, providing a natural cause for Jupiter to predate the inner planets and form within the O(10(exp 7) yr) lifetime of the nebula.

Ward, William R.↗

NASA NTRS2018

Testing and Maturing a Mass Translating Mechanism for a Deep Space CubeSat

Near Earth Asteroid (NEA) Scout is a deep space satellite set to launch aboard NASA’s Exploration Mission 1. The spacecraft fits within a CubeSat standard 6U (about 300 x 200 x 100 mm) and is designed to travel 1 AU over a 2.5 year mission to observe NEA VG 1991. The spacecraft will use an 86 square meter solar sail to maneuver from lunar orbit to the NEA. One of the critical mechanisms aboard NEA Scout, the Active Mass Translator (AMT), has gone through rigorous design and test cycles since its conception in July of 2015. The AMT is a two-axis translation table required to balance the spacecraft’s center of mass (CM) and solar sail center of pressure (CP) while also trimming disturbance torque created by off-nominal sail conditions. The AMT has very limited mass and volume requirements, but is still required to deliver a large translation range—about 160 x 68 mm—at sub mm accuracy and precision. The system must accommodate and protect a shielded wire harness and coax cables during translation. Lastly, the system has been constrained to operate in complete exposure to space with limited power and data budgets for mechanical and thermal needs. The NEA Scout team has developed and carried out a rigorous test suite for the prototype and engineering development unit (EDU). These tests uncovered numerous design failures and led to many failure investigations and iteration cycles. This paper will site each discovery and discuss at length the most surprising and difficult failures to date as the NEA Scout AMT moved through functional, random vibration, thermal vacuum, harnessing, and design life verification testing. A paper was previously presented at the 43rd Aerospace Mechanisms Symposia entitled, “Development of a High Performance, Low Profile Translation Table with Wire Feedthrough for a Deep Space CubeSat”. This paper will make note of specific lessons learned from the test activities: testing ideologies for high-risk missions, thermal mitigation design for small mechanisms, non-flight qualified stepper motor accommodation, harnessing volume allocation/design, and ground testing of mechanisms developed for zero-g environments.

Few, Alex↗

NASA NTRS2018

Testing and Maturing a Mass Translating Mechanism for a Deep Space CubeSat

Near Earth Asteroid (NEA) Scout is a deep space satellite set to launch aboard NASA's Exploration Mission 1. The spacecraft fits within a CubeSat standard 6U (about 300 x 200 x 100 mm) and is designed to travel 1 AU over a 2.5 year mission to observe NEA VG 1991. The spacecraft will use an 86 sq.m solar sail to maneuver from lunar orbit to the NEA. One of the critical mechanisms aboard NEA Scout, the Active Mass Translator (AMT), has gone through rigorous design and test cycles since its conception in July of 2015. The AMT is a two-axis translation table required to balance the spacecraft's center of mass (CM) and solar sail center of pressure (CP) while also trimming disturbance torque created by off-nominal sail conditions. The AMT has very limited mass and volume requirements, but is still required to deliver a large translation range-about 160 x 68 mm-at sub mm accuracy and precision. The system is constrained to operate in complete exposure to space with limited power and data budgets for mechanical and thermal needs. The NEA Scout team developed and carried out a rigorous test suite for the prototype and engineering development unit (EDU). These tests uncovered numerous design failures and led to many failure investigations and iteration cycles. A paper was previously presented at the 43rd Aerospace Mechanisms Symposia entitled, "Development of a High Performance, Low Profile Translation Table with Wire Feedthrough for a Deep Space CubeSat". This paper will make note of specific lessons learned: manufacturing philosophy, testing ideologies for high-risk missions, thermal mitigation design for small, motor-driven mechanisms.

Few, Alex↗

NASA NTRS2005

A Study of Spur Gears Lubricated With Grease-Observations From Seven Experiments

To improve understanding of gears operating with a perfluoro type space-qualified grease, seven spur gear experiments were performed. Test conditions were selected to study the influences of torque, lubricant type, and atmosphere. Two testing torques provided nominal pitch-line Hertz stresses greater and lesser than the contact stress limit as recommended by the grease manufacturer. As was expected, all tests resulted in some gear tooth wear. Discoloration of the perfluoro type grease occurred for all tests. Tests in dry nitrogen produced some dark-grey colored perfluoro type grease. Testing in either ambient or dry air produced red debris after short test duration, and for tests of longer duration large amounts of red debris, red grease, and wear were evident. Tests using higher torques produced more debris. The first indications of discoloration occurred more quickly with higher test torques. Total amounts of wear were quite significant, up to four times the profile tolerance for AGMA Class 10 gears.

Krantz, Timothy L.↗

NASA NTRS1961

Predicted Performance of On-Off Systems for Precise Satellite Attitude Control

An investigation has been made of the use of on-off reaction jets for precision attitude control of a satellite. Since a symmetrical vehicle is assumed, only single-axis control needs to be considered. The responses to initial disturbances and also limit-cycle characteristics for several systems have been evaluated. Calculated results indicate that realistic values of settling time and fuel consumption for the example considered can be obtained. The performance of a given system depends on the characteristics of the error detector used. In cases where the detector output was saturated for a relatively low error input, the settling time deteriorated when a lead network was used to provide damping. This deterioration could be eliminated if a separate rate signal to produce vehicle rate limiting were available. As an alternate approach, two systems were investigated which used a timed sequence of torques and could operate with a detector output of very small linear range. Although the performance of these systems was poorer than that of the lead network system without detector saturation, the performance was better than that of the lead network system with low values of detector saturation. The effects on limit-cycle characteristics of hysteresis, lead network constants, dead zone, and thrust time delays were also investigated.

Brown, Stuart C.↗

NASA NTRS1975

Pyrotechnic shock measurement and data analysis requirements

A study of laboratory measurement and analysis of pyrotechnic shock prompted by a discrepancy in preliminary Mariner Jupiter/Saturn shock test data is reported. It is shown that before generating shock response plots from any recorded pyrotechnic event, a complete review of each instrumentation and analysis system must be made. In addition, the frequency response capability of the tape recorder used should be as high as possible; the discrepancies in the above data were due to inadequate frequency response in the FM tape recorders. The slew rate of all conditioning amplifiers and input converters must be high enough to prevent signal distortion at maximum input voltage; amplifier ranges should be selected so that the input pulse is approximately 50% of full scale; the Bessel response type should be chosen for digital shock analysis if antialiasing filters are employed; and transducer selection must consider maximum acceleration limit, mounted resonance frequency, flat clean mounting surfaces, base bending sensitivity, and proper torque.

Albers, L.↗

NASA NTRS1981

Optimal tooth numbers for compact standard spur gear sets

The design of a standard gear mesh is treated with the objective of minimizing the gear size for a given ratio, pinion torque, and allowable tooth strength. Scoring, pitting fatigue, bending fatigue, and the kinematic limits of contact ratio and interference are considered. A design space is defined in terms of the number of teeth on the pinion and the diametral pitch. This space is then combined with the objective function of minimum center distance to obtain an optimal design region. This region defines the number of pinion teeth for the most compact design. The number is a function of the gear ratio only. A design example illustrating this procedure is also given.

Savage, M.↗

NASA NTRS1981

Optimal tooth numbers for compact standard spur gear sets

Savage, M.↗

NASA NTRS1998

Test of a flexible spacecraft dynamics simulator

There are a number of approaches one can take to modeling the dynamics of a flexible body. While one can attempt to capture the full dynamical behavior subject to disturbances from actuators and environmental torques, such a detailed description often is unnecessary. Simplification is possible either by limiting the amplitude of motion to permit linearization of the dynamics equations or by restricting the types of allowed motion. In this work, we study the nonlinear dynamics of bending deformations of wire booms on spinning spacecraft. The theory allows for large amplitude excursions from equilibrium while enforcing constraints on the dynamics to prohibit those modes that are physically less relevant or are expected to damp out fast. These constraints explicitly remove the acoustic modes (i.e., longitudinal sound waves and shear waves) while allowing for arbitrary bending and twisting, motions which typically are of lower frequency. As a test case, a spin axis reorientation maneuver by the Polar Plasma Laboratory (POLAR) spacecraft has been simulated. POLAR was chosen as a representative spacecraft because it has flexible wire antennas that extend to a length of 65 meters. Bending deformations in these antennas could be quite large and have a significant effect on the attitude dynamics of the spacecraft body. Summary results from the simulation are presented along, with a comparison with POLAR flight data.

Dichmann, Donald↗

NASA NTRSDate not supplied

Handling Qualities of Multirotor RPM-Controlled Electric-Vertical Take-Off and Landing (eVTOL) Aircraft for Urban Air Mobility (UAM)

A paradigm shift in rotorcraft design is being led by the prospect of propulsive forces being distributed across multiple rotors, such that each rotor can be directly driven by a dedicated electric motor. Crucially, some designers attempt to utilize these direct-drive mechanisms as the sole form of primary flight control. The feasibility of this design choice remains to be proven at the scales required for passenger transport. The paper presents a preliminary handling qualities analysis, for a six-passenger (1,200 lb payload) electric Hexacopter conceptual design, which shows that Level 1 handling qualities for limited agility operations are possible, provided that electric powertrains can deliver transient peak torques twice as high as the rated continuous torque of the conceptual design. Preliminary predictions are then substantiated by the results from a piloted handling qualities evaluation conducted in the NASA-Ames Vertical Motion Simulator (VMS). Three eVTOL configurations (a quadrotor, a hexacopter and a lift+cruise) with flight control laws implementing different levels of stability augmentation (Attitude Command-Attitude Hold and Translational Rate Command response types) were evaluated in four low speed and hover tasks requiring various levels of agility and precision.

UAM↗