SEARCH · Search NASA

Results for “Visual platforms”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Estimation and Control for Autonomous Coring from a Rover Manipulator

A system consisting of a set of estimators and autonomous behaviors has been developed which allows robust coring from a low-mass rover platform, while accommodating for moderate rover slip. A redundant set of sensors, including a force-torque sensor, visual odometry, and accelerometers are used to monitor discrete critical and operational modes, as well as to estimate continuous drill parameters during the coring process. A set of critical failure modes pertinent to shallow coring from a mobile platform is defined, and autonomous behaviors associated with each critical mode are used to maintain nominal coring conditions. Autonomous shallow coring is demonstrated from a low-mass rover using a rotary-percussive coring tool mounted on a 5 degree-of-freedom (DOF) arm. A new architecture of using an arm-stabilized, rotary percussive tool with the robotic arm used to provide the drill z-axis linear feed is validated. Particular attention to hole start using this architecture is addressed. An end-to-end coring sequence is demonstrated, where the rover autonomously detects and then recovers from a series of slip events that exceeded 9 cm total displacement.

Hudson, Nicolas↗

NASA NTRS2016

Geocam Space: Enhancing Handheld Digital Camera Imagery from the International Space Station for Research and Applications

Handheld astronaut photography of the Earth has been collected from the International Space Station (ISS) since 2000, making it the most temporally extensive remotely sensed dataset from this unique Low Earth orbital platform. Exclusive use of digital handheld cameras to perform Earth observations from the ISS began in 2004. Nadir viewing imagery is constrained by the inclined equatorial orbit of the ISS to between 51.6 degrees North and South latitude, however numerous oblique images of land surfaces above these latitudes are included in the dataset. While unmodified commercial off-the-shelf digital cameras provide only visible wavelength, three-band spectral information of limited quality current cameras used with long (400+ mm) lenses can obtain high quality spatial information approaching 2 meters/ground pixel resolution. The dataset is freely available online at the Gateway to Astronaut Photography of Earth site (http://eol.jsc.nasa.gov), and now comprises over 2 million images. Despite this extensive image catalog, use of the data for scientific research, disaster response, commercial applications and visualizations is minimal in comparison to other data collected from free-flying satellite platforms such as Landsat, Worldview, etc. This is due primarily to the lack of fully-georeferenced data products - while current digital cameras typically have integrated GPS, this does not function in the Low Earth Orbit environment. The Earth Science and Remote Sensing (ESRS) Unit at NASA Johnson Space Center provides training in Earth Science topics to ISS crews, performs daily operations and Earth observation target delivery to crews through the Crew Earth Observations (CEO) Facility on board ISS, and also catalogs digital handheld imagery acquired from orbit by manually adding descriptive metadata and determining an image geographic centerpoint using visual feature matching with other georeferenced data, e.g. Landsat, Google Earth, etc. The lack of full geolocation information native to the data makes it difficult to integrate astronaut photographs with other georeferenced data to facilitate quantitative analysis such as urban land cover/land use classification, change detection, or geologic mapping. The manual determination of image centerpoints is both time and labor-intensive, leading to delays in releasing geolocated and cataloged data to the public, such as the timely use of data for disaster response. The GeoCam Space project was funded by the ISS Program in 2015 to develop an on-orbit hardware and ground-based software system for increasing the efficiency of geolocating astronaut photographs from the ISS (Fig. 1). The Intelligent Robotics Group at NASA Ames Research Center leads the development of both the ground and on-orbit systems in collaboration with the ESRS Unit. The hardware component consists of modified smartphone elements including cameras, central processing unit, wireless Ethernet, and an inertial measurement unit (gyroscopes/accelerometers/magnetometers) reconfigured into a compact unit that attaches to the base of the current Nikon D4 camera - and its replacement, the Nikon D5 - and connects using the standard Nikon peripheral connector or USB port. This provides secondary, side and downward facing cameras perpendicular to the primary camera pointing direction. The secondary cameras observe calibration targets with known internal X, Y, and Z position affixed to the interior of the ISS to determine the camera pose corresponding to each image frame. This information is recorded by the GeoCam Space unit and indexed for correlation to the camera time recorded for each image frame. Data - image, EXIF header, and camera pose information - is transmitted to the ground software system (GeoRef) using the established Ku-band USOS downlink system. Following integration on the ground, the camera pose information provides an initial geolocation estimate for the individual film frame. This new capability represents a significant advance in geolocation from the manual feature-matching approach for both nadir and off-nadir viewing imagery. With the initial geolocation estimate, full georeferencing of an image is completed using the rapid tie-pointing interface in GeoRef, and the resulting data is added to the Gateway to Astronaut Photography of Earth online database in both Geotiff and Keyhole Markup Language (kml) formats. The integration of the GeoRef software component of Geocam Space into the CEO image cataloging workflow is complete, and disaster response imagery acquired by the ISS crew is now fully georeferenced as a standard data product. The on-orbit hardware component (GeoSens) is in final prototyping phase, and is on-schedule for launch to the ISS in late 2016. Installation and routine use of the Geocam Space system for handheld digital camera photography from the ISS is expected to significantly improve the usefulness of this unique dataset for a variety of public- and private-sector applications.

Stefanov, William L.↗

NASA NTRS2011

Visual PEF Reader - VIPER

This software graphically displays all pertinent information from a Predicted Events File (PEF) using the Java Swing framework, which allows for multi-platform support. The PEF is hard to weed through when looking for specific information and it is a desire for the MRO (Mars Reconn aissance Orbiter) Mission Planning & Sequencing Team (MPST) to have a different way to visualize the data. This tool will provide the team with a visual way of reviewing and error-checking the sequence product. The front end of the tool contains much of the aesthetically appealing material for viewing. The time stamp is displayed in the top left corner, and highlighted details are displayed in the bottom left corner. The time bar stretches along the top of the window, and the rest of the space is allotted for blocks and step functions. A preferences window is used to control the layout of the sections along with the ability to choose color and size of the blocks. Double-clicking on a block will show information contained within the block. Zooming into a certain level will graphically display that information as an overlay on the block itself. Other functions include using hotkeys to navigate, an option to jump to a specific time, enabling a vertical line, and double-clicking to zoom in/out. The back end involves a configuration file that allows a more experienced user to pre-define the structure of a block, a single event, or a step function. The individual will have to determine what information is important within each block and what actually defines the beginning and end of a block. This gives the user much more flexibility in terms of what the tool is searching for. In addition to the configurability, all the settings in the preferences window are saved in the configuration file as well

Luo, Victor↗

NASA NTRS1990

Technologies for global change earth observations

Advances in the areas of space-based observations, data/information analysis, and spacecraft/operations for the studying of global changes are discussed. Research involving systems analysis, observation technologies, information technologies, and spacecraft technologies is examined. Consideration is given to cryogenic coolers, IR arrays, laser and submillimeter sensing, large array CCD, information visualization, design knowledge capture, optical communications, multiinstrument pointing, propulsion, space environmental effects, and platform thermal systems.

Johnston, Gordon I.↗

NASA NTRS1999

Parallel Finite Element Solution of 3D Rayleigh-Benard-Marangoni Flows

A domain decomposition strategy and parallel gradient-type iterative solution scheme have been developed and implemented for computation of complex 3D viscous flow problems involving heat transfer and surface tension effects. Details of the implementation issues are described together with associated performance and scalability studies. Representative Rayleigh-Benard and microgravity Marangoni flow calculations and performance results on the Cray T3D and T3E are presented. The work is currently being extended to tightly-coupled parallel "Beowulf-type" PC clusters and we present some preliminary performance results on this platform. We also describe progress on related work on hierarchic data extraction for visualization.

Carey, G. F.↗

NASA NTRSDate not supplied

A Framework for Sense and Follow Convoys for Collective Autonomous Mobility

Convoys are collections of vehicles that share similar velocity profiles. In the sense-and follow convoy construct, a vehicle can follow a member of an existing convoy resulting in convoy chaining. We prove conditions under which this can occur such that the resulting convoy chain is bounded and the velocities of all members converge to the leader velocity through locally distributed control algorithms. To assess the approach, we utilize a six degree-of-freedom rigid body vehicle dynamics model for each agent. A dynamic inversion based control law is used to track the desired trajectory generated by the convoy algorithms. To simulate the system, we utilize Unity, a cross-platform game engine, where 3-dimensional terrain, building, and vehicle data can be visualized. Numerous simulations are presented to illustrate the concept.

convoys↗

NASA NTRSDate not supplied

A Framework for Sense and Follow Convoys for Collective Autonomous Mobility

convoys↗

NASA NTRS1996

Space Station Furnace Facility Management Information System (SSFF-MIS) Development

This report summarizes the chronology, results, and lessons learned from the development of the SSFF-MIS. This system has been nearly two years in development and has yielded some valuable insights into specialized MIS development. General: In December of 1994, the Camber Corporation and Science Applications International Corporation (SAIC) were contracted to design, develop, and implement a MIS for Marshall Space Flight Center's Space Station Furnace Facility Project. The system was to be accessible from both EBM-Compatible PC and Macintosh platforms. The system was required to contain data manually entered into the MIS as well as data imported from other MSFC sources. Electronic interfaces were established for each data source and retrieval was to be performed at prescribed time intervals. The SOW requirement that predominantly drove the development software selection was the dual-platform (IBM-PC and Macintosh) requirement. The requirement that the system would be maintained by Government personnel influenced the selection of Commercial Off-the-shelf software because of its inherent stability and readily available documentation and support. Microsoft FoxPro Professional 2.6 for Windows and Macintosh was selected as the development tool. This is a software development tool that has been in use for many years. It is stable and powerful. Microsoft has since released the replacement for this product, Microsoft Visual FoxPro, but at the time of this development, it was only available on the Windows platform. The initial contract included included the requirement for capabilities relating to the Work- and Organizational Breakdown Structures, cost (plan and actuals), workforce (plan and actuals), critical path scheduling, trend analysis, procurements and contracts, interface to manufacturing, Safety and Mission Assurance, risk analysis, and technical performance indicators. It also required full documentation of the system and training of users. During the course of the contract, the requirements for Safety and Mission Assurance interface, risk analysis, and technical performance indicators were deleted. Additional capabilities were added as reflected in the Contract Chronology below. Modification 4 added the requirement for Support Contractor manpower data, the ability to manually input data not imported from non-nal sources, a general 'health' indicator screen, and remote usage. Mod 6 included the ability to change the level of planning of Civil Service Manpower at any time and the ability to manually enter Op Codes in the manufacturing data where such codes were not provided by the EMPACS database. Modification 9 included a number of changes to report contents and formats. Modification 11 required the preparation of a detailed System Design Document.

Meade, Robert M.↗

NASA NTRS1994

Control of Wind Tunnel Operations Using Neural Net Interpretation of Flow Visualization Records

Neural net control of operations in a small subsonic/transonic/supersonic wind tunnel at Lewis Research Center is discussed. The tunnel and the layout for neural net control or control by other parallel processing techniques are described. The tunnel is an affordable, multiuser platform for testing instrumentation and components, as well as parallel processing and control strategies. Neural nets have already been tested on archival schlieren and holographic visualizations from this tunnel as well as recent supersonic and transonic shadowgraph. This paper discusses the performance of neural nets for interpreting shadowgraph images in connection with a recent exercise for tuning the tunnel in a subsonic/transonic cascade mode of operation. That mode was operated for performing wake surveys in connection with NASA's Advanced Subsonic Technology (AST) noise reduction program. The shadowgraph was presented to the neural nets as 60 by 60 pixel arrays. The outputs were tunnel parameters such as valve settings or tunnel state identifiers for selected tunnel operating points, conditions, or states. The neural nets were very sensitive, perhaps too sensitive, to shadowgraph pattern detail. However, the nets exhibited good immunity to variations in brightness, to noise, and to changes in contrast. The nets are fast enough so that ten or more can be combined per control operation to interpret flow visualization data, point sensor data, and model calculations. The pattern sensitivity of the nets will be utilized and tested to control wind tunnel operations at Mach 2.0 based on shock wave patterns.

Buggele, Alvin E.↗

NASA NTRS2006

Visual Risk Assessment of Space Radiation Exposure for Future Space Exploration Missions

Protecting astronauts from space radiation exposure during an interplanetary mission is an important challenge for mission design and operations. If sufficient protection is not provided near solar maximum, the risk can be significant due to exposure to sporadic solar particle events (SPEs) as well as to the continuous galactic cosmic radiation (GCR). Polyethylene shielded "storm shelters" inside spacecraft have been shown to limit total exposure from a large SPE to a permissible level, preventing acute risks and providing a potential approach to fulfill the ALARA (as low as reasonably achievable) requirement. For accurate predictions of radiation dose to astronauts involved in future space exploration missions, detailed variations of radiation shielding properties are required. Radiation fluences and doses vary considerably across both the spacecraft geometry and the body-shielding distribution. A model using a modern CAD tool ProE(TradeMark), which is the leading engineering design platform at NASA, has been developed to account for these local variations in the radiation distribution. Visual assessment of radiation distribution at different points inside a spacecraft module and in the human body for a given radiation environment are described. Results will ultimately guide in developing requirements for maximal protection for astronauts from space radiation.

Hussein, Hesham F.↗

NASA NTRS1978

Platform motion for fighter simulations

The reported investigation is concerned with aspects of 'realistic' cue generation and evaluation. 'Realistic' cues are defined to mean cues that are representative of an aircraft, that are of sufficient magnitude to be sensed, that are in the proper direction arriving at the proper time, and yet that are within the presentation capabilities of the washout/synergistic platform system. Attention is given to the aircraft mathematical model, computer implementation, cockpit hardware, visual display, the motion system, vertical acceleration, longitudinal acceleration and pitch rate, and lateral acceleration and roll rate. The motion cues for fighter aircraft produced by Langley nonlinear adaptive washout/synergistic motion base system are found to be unacceptable in the roll axis representation. However, a method for producing potentially realistic roll cues is identified.

Parrish, R. V.↗

NASA NTRS1992

Topography from shading and stereo

Methods exploiting photometric information in images that have been developed in machine vision can be applied to planetary imagery. Present techniques, however, focus on one visual cue, such as shading or binocular stereo, and produce results that are either not very accurate in an absolute sense or provide information only at few points on the surface. We plan to integrate shape from shading, binocular stereo and photometric stereo to yield a robust system for recovering detailed surface shape and surface reflectance information. Such a system will be useful in producing quantitative information from the vast volume of imagery being received, as well as in helping visualize the underlying surface. The work will be carried out on a popular computing platform so that it will be easily accessible to other workers.

Horn, Berthold P.↗

NASA NTRS1993

Topography from shading and stereo

Horn, Berthold P.↗

NASA NTRS1995

Development of a Prototype Simulation Executive with Zooming in the Numerical Propulsion System Simulation

A major difficulty in designing aeropropulsion systems is that of identifying and understanding the interactions between the separate engine components and disciplines (e.g., fluid mechanics, structural mechanics, heat transfer, material properties, etc.). The traditional analysis approach is to decompose the system into separate components with the interaction between components being evaluated by the application of each of the single disciplines in a sequential manner. Here, one discipline uses information from the calculation of another discipline to determine the effects of component coupling. This approach, however, may not properly identify the consequences of these effects during the design phase, leaving the interactions to be discovered and evaluated during engine testing. This contributes to the time and cost of developing new propulsion systems as, typically, several design-build-test cycles are needed to fully identify multidisciplinary effects and reach the desired system performance. The alternative to sequential isolated component analysis is to use multidisciplinary coupling at a more fundamental level. This approach has been made more plausible due to recent advancements in computation simulation along with application of concurrent engineering concepts. Computer simulation systems designed to provide an environment which is capable of integrating the various disciplines into a single simulation system have been proposed and are currently being developed. One such system is being developed by the Numerical Propulsion System Simulation (NPSS) project. The NPSS project, being developed at the Interdisciplinary Technology Office at the NASA Lewis Research Center is a 'numerical test cell' designed to provide for comprehensive computational design and analysis of aerospace propulsion systems. It will provide multi-disciplinary analyses on a variety of computational platforms, and a user-interface consisting of expert systems, data base management and visualization tools, to allow the designer to investigate the complex interactions inherent in these systems. An interactive programming software system, known as the Application Visualization System (AVS), was utilized for the development of the propulsion system simulation. The modularity of this system provides the ability to couple propulsion system components, as well as disciplines, and provides for the ability to integrate existing, well established analysis codes into the overall system simulation. This feature allows the user to customize the simulation model by inserting desired analysis codes. The prototypical simulation environment for multidisciplinary analysis, called Turbofan Engine System Simulation (TESS), which incorporates many of the characteristics of the simulation environment proposed herein, is detailed.

Reed, John A.↗

NASA NTRS1998

Effect of Particle Non-Sphericity on Satellite Monitoring of Drifting Volcanic Ash Clouds

Volcanic eruptions loft gases and ash particles into the atmosphere and produce effects that are both short term (aircraft hazards, interference with satellite measurements) and long term (atmospheric chemistry, climate). Large (greater than 0.5mm) ash particles fall out in minutes [Rose et al, 1995], but fine ash particles can remain in the atmosphere for many days. This fine volcanic ash is a hazard to modem jet aircraft because the operating temperatures of jet engines are above the solidus temperature of volcanic ash, and because ash causes abrasion of windows and airframe, and disruption of avionics. At large distances(10(exp 2)-10(exp 4) km or more) from their source, drifting ash clouds are increasingly difficult to distinguish from meteorological clouds, both visually and on radar [Rose et al., 1995]. Satellites above the atmosphere are unique platforms for viewing volcanic clouds on a global basis and measuring their constituents and total mass. Until recently, only polar AVHRR and geostationary GOES instruments could be used to determine characteristics of drifting volcanic ash clouds using the 10-12 micron window [Prata 1989; Wen and Rose 1994; Rose and Schneider 1996]. The NASA Total Ozone Mapping Spectrometer (TOMS) instruments aboard the Nimbus-7, Meteor3, ADEOS, and Earth Probe satellites have produced a unique data set of global SO2 volcanic emissions since 1978 (Krueger et al., 1995). Besides SO2, a new technique has been developed which uses the measured spectral contrast of the backscattered radiances in the 330-380nm spectral region (where gaseous absorption is negligible) in conjunction with radiative transfer models to retrieve properties of volcanic ash (Krotkov et al., 1997) and other types of absorbing aerosols (Torres et al., 1998).

Krotkov, Nicholay A.↗

NASA NTRSDate not supplied

RadLab: A Comprehensive Database and Graphical and Programming Interfaces for Biologically Relevant Space Radiation Data

RadLab, a new component of the NASA Open Science Data Repository (OSDR), is a platform built upon a database of radiation data relevant to space biology. RadLab provides visual and programmatic interfaces for interrogation of its database, as well as a submission process for inclusion of data from investigators. The RadLab application programming interface (API) implements a request syntax enabling users to retrieve data filtered by various combinations of parameters (detector type, location, direction, timespan, etc), which are delivered in machine-readable text formats, ready to be ingested by downstream analysis pipelines; while the graphical user interface (GUI) provides easy means to iteratively modify query parameters and incorporates a number of standard analyses and visualizations (time series plots, geospatial visualizations, detector comparison). Investigators from many countries, including US, Russia, Japan, Canada, the Czech Republic, Germany, Hungary, and Italy, have committed to provide data from their instruments located on the ISS; RadLab will also include data from other spacecraft in LEO (e.g., the Space Shuttle, the Mir space station), BLEO (e. g. BioSentinel, Mars Orbiter, among others), and on other celestial bodies (e. g. Chang’e 4, Curiosity). The first release of RadLab has been made available to the public. Once fully operational, RadLab will provide a comprehensive and ever-growing compendium of space radiation data, facilitating straightforward access to multiple types of readings and enabling space biology researchers to perform intercomparisons of detectors and to determine the radiation environment of research missions, both via programmatic retrieval of these data and via the graphical analysis toolkit; as well as a user-friendly submission portal for ingesting data from space agencies and research institutions. Radiation scientists will be able to use RadLab to gain a deeper understanding of the space radiation environment for future human space exploration. The RadLab Working Group has been formed to foster close collaborations among data contributors and users, to identify data sources, to put in place standards for data normalization, to guide the development of features of the analysis toolkit, to establish the use of RadLab in space radiation biology research, and eventually to provide a forum for discussing relevant research issues that can take advantage of RadLab's capabilities.

radiation↗

NASA NTRSDate not supplied

Celestial Mapping System for Lunar Surface Mapping and Analytics

Celestial Mapping System (CMS) is a software platform to generate virtual 3D globe for celestial bodies within our solar system. Various layers are built on top of the virtual globe to provide visualization of high resolution imagery, enable precise measurements, build analytical capabilities and broad range of functionalities to assist planetary scientists and mission planners. CMS is built using OpenJDK 11 and will run on a wide variety of platforms such as Linux, Windows, OSX, etc. It has a thick client with less overhead to access hardware resources. This allows features such as terrain profiling and distance calculations to be performed on the client and on the fly. The present focus of CMS is on developing lunar mapping tool kits to provide features such as - 3D first person view with zoom and navigational capabilities, realistic terrain visualization based on LRO data, measurement tools, Apollo landing site annotations, stereoscopic view, elevation profiles, line of sight analysis and many more. The application is developed to provide situational and domain awareness on Lunar surface, planning capabilities for equipment placements and traverse path optimization. As data becomes available, CMS has the capabilities to integrate data sets that change dynamically in real-time, which will be useful for monitoring satellites and remotely-sensed data on Lunar surface. CMS utilizes NASA WorldWind Java library and OpenGL to achieve high-performance rendering of data and measurements, and also adheres to OGC standards. CMS supports importing synthetic features in a variety of 3D, 2D, vector and raster formats. Nomenclature is pulled from USGS Moon IAU2000 database, and lunar parameters are based of the standardized IAU2000 Moon ellipsoid. GDAL (Geospatial Data Abstraction Library) was used to modify and test the accuracy of datasets before integrating into the application. Our high-resolution global elevation model was compared with the LRO LOLA DEM elevation values and tested to ensure accuracy. Celestial Mapping System has several potential use cases for NASA including subsurface lava tubes visualization and analysis, soil analysis, resource visualization and representation on 3D globe.

GIS system↗

NASA NTRSDate not supplied

Visualization and 3D Mesh Generation for ASSEMBLERS Range of Motion

In an effort to create a base and foundation for ASSEMBLERS with an informed layout, data representing the range of motion of varying heights of Stewart platforms were analyzed. 3D shapes were generated first to be approximately representative of these data in the form of rotationally symmetric shells, making use of 2D alpha shapes to create a border that did not account for asymmetry inherent in the true range of motion. Further work was performed to generate mesh files more fully representative of reach, creating 3D alpha shapes based directly on point clouds generated from uniformly random platform positions. These shapes were initially not representative of the entire range of motion of a platform stack due to the low likelihood of the most extreme positions being added to a given point cloud but were more representative of the asymmetry inherent in the possible positions of a Stewart platform as they no longer relied on a single 2D contour. The same algorithm for generating 3D alpha shapes was then applied to point clouds designed to represent extreme positions, generating larger smooth shells with six clear planes of symmetry. All shells were converted to STLs to aid in further modeling of range of motion for base layouts and in visualizing reachable area for varying stack heights, successfully creating closed shells representative of typical and extreme positions for platform stacks of varying heights.

Jonah DeGuire Vanke↗