Evaluation of electroformed nickel to 301 stainless steel resistance spotwelds at 78 deg F and minus 423 deg F
Evaluating electroformed nickel to stainless steel resistance spot welds at room and cryogenic temperatures
WELD STRENGTH↗
SEARCH · Search NASA
Results for “WELDING, RESISTENCE”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of the weldbond process for joining titanium
High quality resistance spot welds were produced by welding through epoxy adhesive on titanium alloys. Weldbond joints were consistently stronger than those of either mechanical fasteners, structural adhesive bonds, or mechanical fasteners with adhesive at the joint interface. Weldbond joints and/or spot weld joints showed superior strength at all temperature ranges as compared to other joints tested.
Fields, D.↗
Manned maneuvering unit latching mechanism
The astronaut/Manned Maneuvering Unit interface, which presented a challenging set of requirements for a latching mechanism, is described. A spring loaded cam segment with variable ratio pulley release actuator was developed to meet the requirements. To preclude jamming of the mechanism, special precautions were taken such as spring loaded bearing points and careful selection of materials to resist cold welding. The mechanism successfully passed a number of tests which partially simulated orbital conditions.
Allton, C. S.↗
New Method For Joining Stainless Steel to Titanium
In new process, edge of stainless-steel sheet is perforated, and joined to titanium by resistance seam welding. Titanium flows into perforations, forming a strong interlocking joint. Process creates a quasi-metallurgical bond between the thin sheets of stainless steel and titanium.
Emanuel, W. H.↗
Fabricating Slotted-Waveguide Arrays From Sheet Metal
Low-cost lightweight waveguides formed from rolls of aluminum. Array formed from sheared, punched, and bent aluminum sheets. Sheets alined with punched jig holes and joined by laser-beam or resistance spot welding. Process permits use of thin metal to reduce raw material costs and mass. Also holds closer tolerances than usually attained in sheet-metal work.
Brown, W. C.↗
The influence of defects of the fatigue resistance of butt and girth welds in A106B steel
This three-phase study was directed at developing a fitness for service defect acceptance criteria for welds with defect indications. The study focussed on A106 Gr. B steel pipe. The first phase involved a literature search and critical review to develop the preliminary acceptance criteria to the extent permitted by the data. The second phase developed data for flat plate, wall segment, and vessel specimens containing artificial or natural planar or volumetric defects. The final phase developed acceptance criteria from the test data.
Leis, B. N.↗
Low cost, SPF aluminum cryogenic tank structure for ALS
Past production work has shown that cryogenic tank structure for the Shuttle Booster Rockets and the Titan system have very high life cycle costs for the fuel tank structure. The tanks are machined stiffener-skin combination that are subsequently formed into the required contour after machining. The material scrap rate for these configurations are usually high, and the loss of a tank panel due to forming or heat treatment problems is very costly. The idea of reducing the amount of scrap material and scrapped structural members has prompted the introduction of built-up structure for cryogenic tanks to be explored on the ALS program. A build-up structure approach that has shown improvements in life cycle cost over the conventional built-up approach is the use of superplastically formed (SPF) stiffened panels (reducing the overall part count and weight for the tank) resistance spot welded (RSW) to outer tank skin material. The stiffeners provide for general stability of the tank, while the skin material provides hoop direction continuity for the loads.
Anton, Claire E.↗
Capillary flow weld-bonding
The invention of a weld-bonding technique for titanium plates was described. This involves fastening at least two plates of titanium together using spot-welding and applying a bead of adhesive along the edge of the resistance spot-welded joint which upon heating, flows and fills the separation between the joint components.
Vaughan, R. W.↗
Stress-strain behavior of cold-welded copper-copper microjunctions in vacuum as determined from electrical resistance measurements
Stress-strain diagrams for cold welded copper microjunctions in vacuum
Przybyszewski, J. S.↗
Understanding radiation effects in friction stir welded MA956 using ion irradiation and a rate theory model
We report an outstanding challenge in the manufacturing and joining of oxide dispersion strengthened steels is retaining the nanofeatures in the alloy throughout the fabrication and welding process. MA956 was friction stir welded with two different sets of welding parameters, resulting in a medium and high heat input. After welding, 5 MeV Fe ++ ion irradiations were performed at doses ranging from 50 to 200 dpa in the temperature range of 400 to 500°C. Post-irradiation characterization was performed with scanning transmission electron microscopy and energy-dispersive x-ray spectroscopy to investigate the Y-Al-O dispersoids, voids, and dislocations. After welding, the dispersoid microstructure coarsened, resulting in fewer and larger dispersoids regardless of heat input. After irradiation, the dispersoid behavior in the welded material was sensitive to temperature, exhibiting growth behavior attributed to Ostwald coarsening at 500 °C but a mixture of nucleation and more muted growth at 400 and 450 °C, attributed to competing mechanisms of radiation-enhanced diffusion and Ostwald coarsening. Void swelling correlated to heat input; being more prevalent in the welded conditions occurring at lower doses and in higher values relative to the base material. The low values of swelling despite microstructure coarsening caused by welding demonstrate the excellent swelling resistance of MA956, even after welding with the highest swelling values of 0.5% noted in the stir zone high heat input condition at 450 °C, 200 dpa. The dislocation behavior was inconsistent: the strongest trend was that network density was higher for welded versus base material, and an increase in loop diameter with temperature was observed. A rate theory model based on the observed microstructure suggests at high temperature interstitial loss to sinks was more likely to be dominant compared to mutual annihilation via point defect recombination, because of an increase of the radiation diffusion coefficient with temperature regardless of initial welded microstructure.
36 MATERIALS SCIENCE↗
Sorting Titanium Welding Rods
Three types of titanium welding wires identified by their resistance to current flow. Welding-wire tester quickly identifies unknown titaniumalloy wire by touching wire with test probe, and comparing meter response with standard response. Before touching wire, tip of test probe dipped into an electrolyte.
Ross, W. D., Jr.↗
Solving Recent Challenges for Wrought Ni-Base Superalloys
This paper reviews the status of technology in design and manufacture of new wrought 21 polycrystalline Ni-base superalloys for critical engineering applications. There is a strong 22 motivation to develop new alloys that are capable of operating at higher temperatures to 23 realise improvements in thermal efficiency, which are necessary to achieve environmental 24 targets for reduced emissions of harmful green-house gases. From the aerospace sector, 25 the development of new powder metallurgy and ingot metallurgy alloys are discussed for 26 disk rotor and static applications. New compositions for powder metallurgy contain about 27 50-55% of gamma prime (γ') strengthening precipitates to ensure components operate 28 successfully at temperatures up to 788°C (1450°F). In contrast, new compositions for ingot 29 metallurgy aim to occupy a design space in temperature capability between Alloy 718 and 30 current powder alloys that are in-service, and show levels of γ' of about 30-44%. The focus 31 in developing these alloys was design for manufacturability. To complement the aerospace 32 developments, a review of work to understand the suitability of candidate alloys for multiple 33 applications in Advanced-Ultra Supercritical (AUSC) power plants has been undertaken by 34 Detrois, Jablonski and Hawk from the National Energy Technology Laboratory. In these 35 power plants, steam temperatures are required to reach 700-760°C. The common thread is 36 to develop alloys that demonstrate a combination of high temperature properties, which are 37 reliant on both the alloy composition and microstructure and can be produced readily at the 38 right price. For the AUSC applications, the emphasis is on high temperature strength, long 39 term creep life, phase stability, oxidation resistance and robust welding for fabrications. 40 Whereas for powder disk rotors in aircraft engines, the priority is enhanced resistance to 41 time dependent crack growth, phase stability and resistance to environmental damage, while 42 extending the current strength levels, which are shown by existing alloys, to higher 43 temperatures.
36 MATERIALS SCIENCE↗
Upper limit for magnetoresistance in silicon bronze and phosphor bronze wire
The electrical resistivity of silicon bronze and phosphor bronze was measured in magnetic fields from 0 to 14 T and at temperatures between 2 and 300 K. At any fixed temperature, the change in resistivity to 14 T was less than a few parts in 100,000. Thus, these bronzes are excellent for use in high magnetic fields where constant resistance is required. Welding leads to the sample was found to be superior to soldering. The soldered contacts were subject to spurious resistivity changes that resulted from superconducting transitions in the solder.
Feldman, R.↗
Microstructural, Corrosion and Mechanical Characterization of Friction-Stir Welded Joints Between Aluminum and Magnesium Alloys
Friction Stir Welding (FSW) of Aluminum-Magnesium (Al-Mg) alloys has garnered increasing attention due to its wide-ranging applications in the automotive and aerospace industries. The microstructural, corrosion, and mechanical properties of FSW Al-Mg welds under selected conditions are critical factors that must be well-investigated to ensure their durability and performance. In this study, electrochemical tests, including Open Circuit Potential (OCP), Linear Polarization Resistance (LPR), Potentiodynamic Polarization Scan (PD), and Electrochemical Impedance Spectroscopy (EIS), have been used to analyze the corrosion resistance of these welds, along with weight loss measurements through cyclic corrosion testing (CCT) and surface evolution via SEM over an 8-week period. Mechanical properties are evaluated through microindentation, nanoindentation, fatigue, and lap-shear tests. The results of the electrochemical tests reveal that the corrosion properties of the center weld zone differ from those of the two base alloys. Indentation tests indicate that the weld zone behaves differently from the base alloys. Surprisingly, the lap shear strength did not decrease significantly even after 8 weeks of cyclic corrosion testing, indicating that the joint prevented any ingress of the electrolyte. Fatigue testing showed that applying an adhesive between the Al and Mg joint improved the fatigue life to some extent, although the corrosion resistance reduced due to the discontinuous bonding of the adhesive layer. Overall, these findings highlight the importance of investigating the corrosion and mechanical properties of FSW Al-Mg welds and provide valuable insights for future modeling works.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Friction plug welding
Friction plug welding (FPW) usage is advantageous for friction stir welding (FSW) hole close-outs and weld repairs in 2195 Al--Cu--Li fusion or friction stir welds. Current fusion welding methods of Al--Cu--Li have produced welds containing varied defects. These areas are found by non-destructive examination both after welding and after proof testing. Current techniques for repairing typically small (<0.25) defects weaken the weldment, rely heavily on welders' skill, and are costly. Friction plug welding repairs increase strength, ductility and resistance to cracking over initial weld quality, without requiring much time or operator skill. Friction plug welding while pulling the plug is advantageous because all hardware for performing the weld can be placed on one side of the workpiece.
Takeshita, Riki↗
Irradiation of Advanced Cladding Specimens in the High Flux Isotope Reactor: Capsule Designs and Test Matrix
The Advanced Fuels Campaign (AFC) has initiated the Advanced Reactor Cladding (ARC) irradiation campaign to generate irradiation performance data for candidate fuel cladding concepts. The campaign includes a diverse set of ferritic/martensitic steels, oxide dispersion strengthened (ODS) alloys, FeCrAlbased alloys, coated materials, and welded cladding specimens produced through multiple US Department of Energy (DOE) programs and international collaborations. Three complementary experimental thrusts comprise the campaign: tensile testing (ARC Tensile) to rapidly screen candidate alloys, fracture toughness testing (ARC Fracture) to evaluate irradiation effects on crack resistance, and tubular weld testing (ARC Weld) to quantify irradiation-induced changes in the mechanical performance of end cap welds. This report documents the irradiation campaign design, including the selected materials, specimen types, irradiation matrix, and capsule designs for irradiation within the High Flux Isotope Reactor (HFIR). A total of 14 irradiation capsules were developed to achieve target irradiation temperatures between 300°C and 600°C and doses up to 30 dpa. Thermal analyses were performed using finite element methods to establish capsule geometries capable of achieving the desired specimen temperatures while accommodating differences in specimen geometry and material properties. The resulting capsule designs provide the basis for irradiation of the AFC-ARC experimental matrix and subsequent post-irradiation examination to assess the effects of neutron irradiation on advanced cladding materials.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Peening Techniques for Mitigating Chlorine-Induced Stress Corrosion Cracking of Dry Storage Canisters for Nuclear Applications
Fusion-welded austenitic stainless steel (ASS) was predominantly employed to manufacture dry storage canisters (DSCs) for the storage applications of spent nuclear fuel (SNF). However, the ASS weld joints are prone to chloride-induced stress corrosion cracking (CISCC), a critical safety issue in the nuclear industry. DSCs were exposed to a chloride-rich environment during storage, creating CISCC precursors. The CISCC failure leads to nuclear radiation leakage. Therefore, there is a critical need to enhance the CISCC resistance of DSC weld joints using promising repair techniques. This review article encapsulates the current state-of-the-art of peening techniques for mitigating the CISCC in DSCs. More specifically, conventional shot peening (CSP), ultrasonic impact peening (UIP), and laser shock peening (LSP) were elucidated with a focus on CISCC mitigation. The underlying mechanism of CISCC mitigation in each process was summarized. Finally, this review provides recent advances in surface modification techniques, repair techniques, and developments in welding techniques for CISCC mitigation in DSCs.
Chemistry↗