Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND TUNNEL NOZZLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Gust Generator for a Supersonic Wind Tunnel

The effectiveness was investigated of a flat plate gust generator that was located in the nozzle throat of the Lewis 10- by 10-foot supersonic wind tunnel. Gust plates were tested at nozzle wall Mach numbers of 3.1, 2.4, and 2.0. Test results show that the flat plate concept may be used as a gust generator for a wind tunnel; however, more extensive investigation is required to completely define its capabilities and limitations. For the single transient data point recorded, a gust amplitude (decrement) of 0.15 in Mach number was obtained. Analysis of these transient data indicates a response with a corner frequency of at least 8 hertz.

Sanders, Bobby W.↗
NASA NTRS2002

Propulsion Simulations with the Unstructured-Grid CFD Tool TetrUSS

A computational investigation has been completed to assess the capability of the NASA Tetrahedral Unstructured Software System (TetrUSS) for simulation of exhaust nozzle flows. Three configurations were chosen for this study: (1) a fluidic jet effects model, (2) an isolated nacelle with a supersonic cruise nozzle, and (3) a fluidic pitchthrust- vectoring nozzle. These configurations were chosen because existing data provided a means for measuring the ability of the TetrUSS flow solver USM3D for simulating complex nozzle flows. Fluidic jet effects model simulations were compared with structured-grid CFD (computational fluid dynamics) data at Mach numbers from 0.3 to 1.2 at nozzle pressure ratios up to 7.2. Simulations of an isolated nacelle with a supersonic cruise nozzle were compared with wind tunnel experimental data and structured-grid CFD data at Mach numbers of 0.9 and 1.2, with a nozzle pressure ratio of 5. Fluidic pitch-thrust-vectoring nozzle simulations were compared with static experimental data and structured-grid CFD data at static freestream conditions and nozzle pressure ratios from 3 to 10. A fluidic injection case was computed with the third configuration at a nozzle pressure ratio of 4.6 and a secondary pressure ratio of 0.7. Results indicate that USM3D with the S-A turbulence model provides accurate exhaust nozzle simulations at on-design conditions, but does not predict internal shock location at overexpanded conditions or pressure recovery along a boattail at transonic conditions.

Deere, Karen A.↗
NASA NTRS1981

Thrust reversing effects on twin-engine aircraft having nonaxisymmetric nozzles

The effects of thrust reversing on stability, control and vertical tail loads of advanced fighter aircraft are reviewed. Several static test stand and wind tunnel investigations of nonaxisymmetric nozzles with integral thrust reversers are presented, and it is found that base drag on the aft face of reverser panels of blockers provides a significant contribution to in-flight thrust reverser performance. The location of tail surfaces relative to the thrust reverser has significant impact on control surface effectiveness, and depending on thrust reverser location, large vertical tail side force can result from the use of in-flight thrust reversers. It is concluded that highly effective nonaxisymmetric nozzle reversers can be designed to achieve a 50% static reverse thrust.

Capone, F. J.↗
NASA NTRS1978

Status of a nozzle-airframe study of a highly maneuverable fighter

NASA is sponsoring a research program that uses coordinated wind tunnel and flight tests to investigate nozzle-airframe flow interactions. The program objective is to compare transonic flight and wind tunnel measurements over a wide Reynolds number range. The paper discusses the progress of the program and the coordination of the wind tunnel and flight tests with regard to program elements, model-airplane differences, instrument locations, and test conditions. The real-time feedback techniques used to obtain steady flight conditions are presented. Available wind tunnel results are presented for the jet effects model showing the influence of the rear-end geometry and test variables on nozzle drag. Available flight results show the effect of the variable inlet ramp angle and angle of attack on fuselage pressures and upper surface boundary layers.

Nugent, J.↗
NASA NTRS1977

Static and wind tunnel near-field/far-field jet noise measurements from model scale single-flow base line and suppressor nozzles. Summary report

A test program was conducted in the Boeing large anechoic test chamber and the NASA-Ames 40- by 80-foot wind tunnel to study the near- and far-field jet noise characteristics of six baseline and suppressor nozzles. Static and wind-on noise source locations were determined. A technique for extrapolating near field jet noise measurements into the far field was established. It was determined if flight effects measured in the near field are the same as those in the far field. The flight effects on the jet noise levels of the baseline and suppressor nozzles were determined. Test models included a 15.24-cm round convergent nozzle, an annular nozzle with and without ejector, a 20-lobe nozzle with and without ejector, and a 57-tube nozzle with lined ejector. The static free-field test in the anechoic chamber covered nozzle pressure ratios from 1.44 to 2.25 and jet velocities from 412 to 594 m/s at a total temperature of 844 K. The wind tunnel flight effects test repeated these nozzle test conditions with ambient velocities of 0 to 92 m/s.

Jaeck, C. L.↗
NASA NTRS1991

Use of the PARC code for generic NASP nozzles operating at off-design transonic conditions

A three-dimensional Navier-Stokes solver, PARC3D, has been investigated for applications to the wind tunnel testing of high-speed nozzle configurations, particularly with extended expansion ramps, operating at transonic off-design conditions. Numerous cases have been run and compared with existing wind tunnel data. The code has been shown to be an efficient and robust tool in the analysis of complex nozzle configurations whose flows are substantially determined by three-dimensional effects. Although the method requires that a grid, generated independently of the code, be supplied to it, the robust nature of the code does not require that this grid be excessively detailed, nor does it seem to require that the grid be fine-tuned for individual cases. The directness and flexibility of the boundary condition specifications allow a variety of configurations and flow conditions to be handled very efficiently.

Yaros, Steven F.↗
NASA NTRS1998

Initial Flight Test Evaluation of the F-15 ACTIVE Axisymmetric Vectoring Nozzle Performance

A full envelope database of a thrust-vectoring axisymmetric nozzle performance for the Pratt & Whitney Pitch/Yaw Balance Beam Nozzle (P/YBBN) is being developed using the F-15 Advanced Control Technology for Integrated Vehicles (ACTIVE) aircraft. At this time, flight research has been completed for steady-state pitch vector angles up to 20' at an altitude of 30,000 ft from low power settings to maximum afterburner power. The nozzle performance database includes vector forces, internal nozzle pressures, and temperatures all of which can be used for regression analysis modeling. The database was used to substantiate a set of nozzle performance data from wind tunnel testing and computational fluid dynamic analyses. Findings from initial flight research at Mach 0.9 and 1.2 are presented in this paper. The results show that vector efficiency is strongly influenced by power setting. A significant discrepancy in nozzle performance has been discovered between predicted and measured results during vectoring.

Orme, John S.↗
NASA NTRS1976

Aerodynamic performance of flared fan nozzles used as inlets

Tests were conducted in a low speed wind tunnel to determine the aerodynamic performance of several flared fan nozzles. Each of the flared nozzles was a downstream-facing inlet to a model fan that was used to simulate a variable pitch fan during reverse thrust operation. The total pressure recovery of each of the flared nozzles as well as that of an unflared nozzle and a serrated flare nozzle was obtained for comparison. The aerodynamic performance of a selected flared nozzle was considered in further detail. The nozzle surface pressures for a flared nozzle were also determined. Results indicated that the differences in aerodynamic performance among the nozzles were most apparent at the wind-tunnel-off condition. A nonzero free stream velocity significantly reduced the perforamnce of all the nozzles, and crosswind flow (free stream flow perpendicular to the model axis) further reduced the performance of the nozzles. The unflared nozzle and the serrated flare nozzle had reduced aerodynamic performance compared to a solid surface flared nozzle.

Dietrich, D. A.↗
NASA NTRS1997

Survey of Aerothermodynamics Facilities Useful for the Design of Hypersonic Vehicles Using Air-Breathing Propulsion

This paper surveys the use of aerothermodynamic facilities which have been useful in the study of external flows and propulsion aspects of hypersonic, air-breathing vehicles. While the paper is not a survey of all facilities, it covers the utility of shock tunnels and conventional hypersonic blow-down facilities which have been used for hypersonic air-breather studies. The problems confronting researchers in the field of aerothermodynamics are outlined. Results from the T5 GALCIT tunnel for the shock-on lip problem are outlined. Experiments on combustors and short expansion nozzles using the semi-free jet method have been conducted in large shock tunnels. An example which employed the NASA Ames 16-Inch shock tunnel is outlined, and the philosophy of the test technique is described. Conventional blow-down hypersonic wind tunnels are quite useful in hypersonic air-breathing studies. Results from an expansion ramp experiment, simulating the nozzle on a hypersonic air-breather from the NASA Ames 3.5 Foot Hypersonic wind tunnel are summarized. Similar work on expansion nozzles conducted in the NASA Langley hypersonic wind tunnel complex is cited. Free-jet air-frame propulsion integration and configuration stability experiments conducted at Langley in the hypersonic wind tunnel complex on a small generic model are also summarized.

Arnold, James O.↗
NASA NTRS2020

Direct Numerical Simulations of Acoustic Disturbances in Various Rectangular Nozzle Configurations

We perform Direct Numerical Simulations (DNS) to study the acoustic freestream disturbances radiating from the turbulent boundary layers along the contoured nozzle walls of a hypersonic wind tunnel with a rectangular test section. To begin with, the effects of the spanwise end walls are suppressed by confining the spanwise computational domain to a finite segment of the overall nozzle cross section and by imposing periodic boundary conditions across that spanwise domain. Besides providing a building-block configuration to reveal par- tial effects of the enclosed acoustic environment within the wind tunnel, these computations serve as a stepping stone toward the goal of fully-3D computations including the nozzle end walls. Building upon the earlier simulations of Deegan et al. (2018), we show that the computed acoustic characteristics in the spanwise periodic simulations are insensitive to changes in the grid resolution parameters (e.g., x+ and z+). This is relative to the previous simulations that involved a coarser resolution in the streamwise and wall-normal directions, especially up- stream of the test section. Furthermore, we outline a comparison of the pressure fluctuations induced by the turbulent boundary layers over the contoured nozzle walls and several other calculations involving boundary layers over a single flat plate at nearly the same value of the edge Mach number. We also show the impact of having only one turbulent boundary layer instead of two within the computational setup. Various flow statistics, including the first and second moments of the unsteady flow field, are computed for the different flow configurations. Good comparisons of the statistics of the nozzle-wall boundary-layer turbulence and of the freestream acoustic disturbances between the simulations of coarser and finer grids confirms DNS procedure, but also the insensitivity of noise characteristics t section to the inflow turbulence generation technique.

Hildebrand, Nathaniel↗
NASA NTRS1997

Design and Checkout of a High Speed Research Nozzle Evaluation Rig

The High Flow Jet Exit Rig (HFJER) was designed to provide simulated mixed flow turbojet engine exhaust for one- seventh scale models of advanced High Speed Research test nozzles. The new rig was designed to be used at NASA Lewis Research Center in the Nozzle Acoustic Test Rig and the 8x6 Supersonic Wind Tunnel. Capabilities were also designed to collect nozzle thrust measurement, aerodynamic measurements, and acoustic measurements when installed at the Nozzle Acoustic Test Rig. Simulated engine exhaust can be supplied from a high pressure air source at 33 pounds of air per second at 530 degrees Rankine and nozzle pressure ratios of 4.0. In addition, a combustion unit was designed from a J-58 aircraft engine burner to provide 20 pounds of air per second at 2000 degrees Rankine, also at nozzle pressure ratios of 4.0. These airflow capacities were designed to test High Speed Research nozzles with exhaust areas from eighteen square inches to twenty-two square inches. Nozzle inlet flow measurement is available through pressure and temperature sensors installed in the rig. Research instrumentation on High Speed Research nozzles is available with a maximum of 200 individual pressure and 100 individual temperature measurements. Checkout testing was performed in May 1997 with a 22 square inch ASME long radius flow nozzle. Checkout test results will be summarized and compared to the stated design goals.

Castner, Raymond S.↗
NASA NTRS2022

Interaction of a Tunnel-like Acoustic Disturbance Field with a Blunt Cone Boundary Layer at Mach 8

The existing measurements of laminar-to-turbulent transition over circular cones in conventional (i.e., “noisy”) hypersonic wind tunnels have established that the transition location moves downstream when the nose radius is increased from zero. However, this initially downstream movement slows down and ultimately reverses beyond a critical value of the nose radius, and may be related to external forcing in the form of freestream disturbances and/or surface roughness. To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, hypersonic boundary-layer receptivity to broadband freestream acoustic disturbances from the nozzle wall of a digital conventional wind tunnel is investigated by both direct numerical simulations (DNS) and modal and nonmodal stability analysis. A Mach 8 flow over a 7 deg half-angle cone with a nose radius of 𝑅 𝑛 = 5.2mm and freestream Reynolds number of 12.2 × 10 6 m -1 is considered. The results show that the broadband tunnel noise in the free stream of a convectional hypersonic wind tunnel (i.e., outside of the nozzle-wall turbulent boundary layer) can be well represented by an acoustic model with an ansatz of slow acoustic waves. With successful calibration of the model parameters against the precursor tunnel DNS, such an acoustic ansatz can successfully reproduce both the frequency-wavenumber spectra and the temporal evolution of the broadband tunnel noise radiated from the nozzle wall. Additionally, the DNS of the Mach 8 blunt cone with tunnel-like acoustic input above the bow shock showed that the spectra of wall-pressure and heat-transfer fluctuations recovers the signature of the axisymmetric waves predicted by the nonmodal analysis. Furthermore, the azimuthal wavenumber and frequency spectrum of the temperature fluctuations as a function of the wall-normal distance show higher amplitudes for three-dimensional waves above the boundary-layer edge. The numerical schlieren contours show the inclined structures commonly observed in blunt cone experiments, demonstrating that they correspond to three-dimensional structures due to freestream disturbances in the presence of an entropy layer.

Boundary-layer transition↗
NASA NTRS1977

Evaluation of the in-flight noise signature of a 32-chute suppressor nozzle: Acoustic data report

Outdoor static and 40 x 80 FT wind tunnel tests of the J79-15 engine/nacelle system with the conic nozzle and 32-chute exhaust suppressor were conducted to acquire the data necessary to evaluate the simulated in-flight signature of an engine-size 32-chute exhaust nozzle suppressor using the 40 x 80 ft wind tunnel and to study possible engine core noise contamination of the jet signature. The tests are described and and a sampling of the data acquired is presented. Included are aero performance summaries, as-measured and composite 1/3 OBSPL spectra for the 70 ft sideline high and low mics from the outdoor static tests, sideline traverse spectra and internal noise measurements from both the outdoor static and the 40 x 80 ft wind tunnel tests.

Moore, M. T.↗
NASA NTRS1991

J-85 jet engine noise measured in the ONERA S1 wind tunnel and extrapolated to far field

Noise from a J-85 turbojet with a conical, convergent nozzle was measured in simulated flight in the ONERA S1 Wind Tunnel. Data are presented for several flight speeds up to 130 m/sec and for radiation angles of 40 to 160 degrees relative to the upstream direction. The jet was operated with subsonic and sonic exhaust speeds. A moving microphone on a 2 m sideline was used to survey the radiated sound field in the acoustically treated, closed test section. The data were extrapolated to a 122 m sideline by means of a multiple-sideline source-location method, which was used to identify the acoustic source regions, directivity patterns, and near field effects. The source-location method is described along with its advantages and disadvantages. Results indicate that the effects of simulated flight on J-85 noise are significant. At the maximum forward speed of 130 m/sec, the peak overall sound levels in the aft quadrant were attentuated approximately 10 dB relative to sound levels of the engine operated statically. As expected, the simulated flight and static data tended to merge in the forward quadrant as the radiation angle approached 40 degrees. There is evidence that internal engine or shock noise was important in the forward quadrant. The data are compared with published predictions for flight effects on pure jet noise and internal engine noise. A new empirical prediction is presented that relates the variation of internally generated engine noise or broadband shock noise to forward speed. Measured near field noise extrapolated to far field agrees reasonably well with data from similar engines tested statically outdoors, in flyover, in a wind tunnel, and on the Bertin Aerotrain. Anomalies in the results for the forward quadrant and for angles above 140 degrees are discussed. The multiple-sideline method proved to be cumbersome in this application, and it did not resolve all of the uncertainties associated with measurements of jet noise close to the jet. The simulation was complicated by wind-tunnel background noise and the propagation of low frequency sound around the circuit.

Soderman, Paul T.↗
NASA NTRS1975

Contribution of the National Aeronautics and Space Administration Langley Research Center

As part of a special international effort, three nozzles were designed and tested on single nacelle models in wind tunnels of several nations belonging to the North Atlantic Treaty Organization. All three of these nozzles were investigated in the Langley 16-foot transonic wind tunnel at the National Aeronautics and Space Administration's Langley Research Center. Langley Research Center also contributed theoretical calculations of the jet plume boundary and afterbody pressures. The calculations were obtained using an iterative solution which combined the inviscid Douglas Neumann method for the external flow with the method of characteristics for the flow in the jet plume. For the investigation, the nozzles were mounted on a single nacelle model 15.24 centimeters in diameter and 162.56 centimeters long. Tests were made at free stream Mach number from 0.4 to 1.2, and at Reynolds numbers per meter from 7.38 million to 13.78 million depending on the Mach number. Four types of data were recorded: afterbody pressure data, afterbody force data, model boundary layer data, and tunnel wall pressure data. The ratio of jet total pressure to free stream static pressure ranged up to 8.5. A description of the wind tunnel, model, and test procedure is included.

Compton, W. B., III↗
NASA NTRS1995

Supersonic quiet-tunnel development for laminar-turbulent transition research

This grant supported research into quiet-flow supersonic wind-tunnels, between February 1994 and February 1995. Quiet-flow nozzles operate with laminar nozzle-wall boundary layers, in order to provide low-disturbance flow for studies of laminar-turbulent transition under conditions comparable to flight. Major accomplishments include: (1) development of the Purdue Quiet-Flow Ludwieg Tube, (2) computational evaluation of the square nozzle concept for quiet-flow nozzles, and (3) measurement of the presence of early transition on the flat sidewalls of the NASA LaRC Mach 3.5 supersonic low-disturbance tunnel. Since items (1) and (2) are described in the final report for companion grant NAG1-1133, only item (3) is described here. A thesis addressing the development of square nozzles for high-speed, low-disturbance wind tunnels is included as an appendix.

Schneider, Steven P.↗