Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING FLAPS, HINGED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1941

Wind-tunnel investigation of spoiler, deflector, and slot lateral-control devices on wings with full-span split and slotted flaps

Report presents the results of an extensive investigation made in the NACA 7 by 10-foot wind tunnel of spoiler, deflector, and slot types of lateral-control device on wings with full-span split and slotted flaps. The static rolling and yawing moments were determined for all the devices tested, and the static hinge moments and the time response were determined for a few devices of each type.

Wenzinger, Carl J↗
NASA NTRS1933

Flight Tests on the Lateral Control of an Airplane having a Split Flap which Retracts Ahead of Conventional Ailerons, Special Report

Since the recent more or less extensive adoption of high-lift flaps on airplane wings, the problem of providing satisfactory lateral control without sacrificing a part of the span of the flaps has become one of some importance. The difficulties have been largely a matter of obtaining satisfactory rolling moments with a smoothly graduated action, together with sufficiently small control forces throughout the entire speed range. As part of an investigation including several different lateral-control arrangements to be used with split flaps, the tests reported in this paper were made on one arrangement in which conventional ailerons of narrow chord are used, and a split flap is retracted into the under surface of th wing forward of th ailerons. When the flap is retracted, the arrangement is as sketched in figure 1(a). If a simple form of split flap were used, hinged at its forward edge, the appearance when deflected would be as shown in figure 1(b). The flap if deflected with its leading edge remaining in this forward position would give somewhat less than three fourths of the lift increase of the same flap in the usual rear position. (See reference 1.). If, as shown in figure 1(c), the split flap ahead of th aileron is moved to the rear as the trailing=edge portion is deflected downward, a double advantage is obtained. The deflected flap can be located in the most effective region for high lift (reference 1), and the force required to deflect the flap is reduced. This is the arrangement used in the present tests.

Weick, Fred E.↗
NASA NTRS2010

Active Flow Control of Lifting Surface With Flap-Current Activities and Future Directions

The main objective is to develop effective control strategies for separation control of an airfoil with a single hinge flap. The specific objectives are: Develop an active control architecture for flow control around an airfoil with flap. Design, fabricate, a wind tunnel test of a high lift wing (with flap) with integrated actuators and sensors. Design, development and fabrication of synthetic jet actuators. Develop appropriate control strategy for application to the airfoil. Wind tunnel testing of the high lift wing at various angles of attack and flap positions with closed loop control.

Ahmadi, G.↗
NASA NTRS1983

Vortical flow management for improved configuration aerodynamics: Recent experiences

Recent progress in vortex-control applications for alleviating the adverse consequences of three dimensional separation and vortical interactions on slender body/swept wing configurations is reported. Examples include helical separation trip to alleviate the side force due to forebody vortex asymmetry; hinged strakes to avoid vortex breakdown effects; compartmentation of swept leading edge separation to delay the pitch-up instability; under wing vortex trip and vortex trip and vortex flaps for drag reduction at high lift; and an apex-flap trimmer to fully utilize the lift capability of trailing-edge flaps for take off and landing of delta wings. Experimental results on generic wind-tunnel models are presented to illustrate the vortex-management concepts involved and to indicate their potential for enhancing the subsonic aerodynamics of supersonic-cruise type vehicles.

Rao, D. M.↗
NASA NTRS1974

Effects of air breathing engine plumes on SSV orbiter subsonic wing pressure distribution, volume 2

Data presented were obtained during wind tunnel tests of a 0.0405-scale model of the -89B ferry configuration of the space shuttle vehicle orbiter. These tests were conducted in the Rockwell International low speed wind tunnel (NAAL). The primary test objective was to investigate orbiter wing pressure distributions resulting from nacelle plumes above and below the wing. Three six-engine nacelle configurations were tested. One configuration has a twin-podded nacelle mounted above each wing and the others had one mounted below each wing. Both had a centerline twin-podded nacelle mounted below the wing. Wing pressure distribution was determined by locating static pressure bugs on the upper and lower surfaces of the left wing. Pressure bugs were also located on the upper and lower surfaces of the body flap and on the B12 afterbody fairing when it was installed. Base and balance cavity pressures were recorded and a strain gage instrumented beam in the right wing measured elevon hinge moments and normal forces.

Soard, T.↗
NASA NTRS1974

Effects of air breathing engine plumes on SSV orbiter subsonic wing pressure distribution (OA57B), volume 1

Data were obtained during wind tunnel tests of a 0.0405-scale model of the ferry configuration of the space shuttle vehicle orbiter conducted in a low speed wind tunnel during the time period of September 18 to September 23, 1973. The primary test objective was to investigate orbiter wing pressure distributions resulting from nacelle plumes above and below the wing. Three six-engine nacelle configurations were tested. One configuration had a twin-podded nacelle mounted above each wing and the others had one mounted below each wing. Both had a centerline twin-podded nacelle mounted below the wing. Wing pressure distribution was determined by locating static pressure bugs on the upper and lower surfaces of the left wing. Pressure bugs were also located on the upper and lower surfaces of the body flap and on the B12 afterbody fairing when it was installed. Base and balance cavity pressures were recorded and a strain gage instrumented beam in the right wing measured elevon hinge moments and normal forces.

Soard, T.↗
NASA NTRS1946

The Development of a Lateral-control System for Use with Large-span Flaps

A spoiler-type lateral-control system has been developed for use on the Northrop P-61 airplane. The lateral-control system is to be used with large-span flaps and consists of a thin circular arc spoiler, linked with a short-span plain aileron located just outboard of the spoiler. This unconventional lateral-control system has been accepted with enthusiasm by the pilots who have flown the airplane. The particularly appreciate its characteristic at high speed. The combination of light forges, favorable yawing moment, and low wing torsional moments, make it a very effective, easily applied control. The control available at and through the stall is also remarkably good, although this characteristic may be attributed, in part, to an exceptionally good wing stalling pattern rather than entirely to the use of the spoiler-type aileron. In the landing configuration, the lateral-control effectiveness increases automatically with the extension of wing flaps so that powerful control is available during the approach. There is, however, a decrease in effectiveness for the first 5 percent of the wheel travel with a resultant tendency for inexperienced pilots to overcontrol slightly at low speeds. The fact that the aileron can be fully used at the stall, however, more than compensates for this loss of effectiveness with flaps down and greatly enhances the airplane's landing performance.

AIRPLANES - NORTHROP P-61 FLIGHT TESTS (AMER )↗
NASA NTRS1983

Segmented vortex flaps

Segmented vortex flaps were suggested as a means of delaying the vortex spill-over causing thrust loss over the outboard region of single-panel flaps. Also proposed was hinge-line setback for exploiting leading-edge suction in conjunction with vortex flaps to improve the overall thrust per unit flap area. These two concepts in combination were tested on a 60-deg cropped delta wing model. Significant improvement in flap efficiency was indicated by a reduction of the flap/wing area from 11.4% of single-panel flap to 6.3% of a two segment delta flap design, with no lift/drag penalty at lift coefficients between 0.5 and 0.7. The more efficient vortex flap arrangement of this study should benefit the performance attainable with flaps of given area on wings of moderate leading-edge sweep.

Rao, D. M.↗
NASA NTRS2001

In-Flight Flow Visualization Results of The F-106B With a Vortex Flap

Surface and off-surface flow visualization techniques were used to visualize the three-dimensional vortex flows on the F-106 aircraft with vortex flaps installed. Results at angles of attack between 9 deg to 18 deg and Mach numbers from 0.3 to 0.9 are presented. A smoke flow vapor screen technique was used to document leading-edge vortex paths and sizes, while an oil flow technique was employed to provide detailed information on reattachment and separation line locations and other flow details. Results were obtained for two vortex flap deflection angles, 30 deg and 40 deg. Flow visualization revealed the existence of a multiple vortex system that had not previously been seen in subscale tests or predicted for this configuration. The vortex flap generated a leading-edge vortex system that reattached near the flap hinge over a wide angle of attack range. In addition to the primary vortex, flow visualization revealed the presence of several distinct vortices which traced a path from the vortex flap and then over the wing.

Brandon, Jay M.↗
NASA NTRS2003

In-Flight Flow Visualization Results of the F-106B with a Vortex Flap

Surface and off-surface flow visualization techniques were used to visualize the three-dimensional vortex flows on the F-106 aircraft with vortex flaps installed. Results at angles of attack between 9 degrees to 18 degrees and Mach numbers from 0.3 to 0.9 are presented. A smoke flow vapor screen technique was used to document leading-edge vortex paths and sizes, while an oil flow technique was employed to provide detailed information on reattachment and separation line locations and other flow details. Results were obtained for two vortex flap deflection angles, 30 degrees and 40 degrees. Flow visualization revealed the existence of a multiple vortex system that had not previously been seen in subscale tests or predicted for this configuration. The vortex flap generated a leading-edge vortex system that reattached near the flap hinge over a wide angle of attack range. In addition to the primary vortex, flow visualization revealed the presence of several distinct vortices which traced a path from the vortex flap and then over the wing.

Brandon, Jay M.↗
NASA NTRS1983

An experimental study of pressures on 60 deg Delta wings with leading edge vortex flaps

An experimental study was conducted in the Virginia Tech Stability Wind Tunnel to determine surface pressures over a 60 deg sweep delta wing with three vortex flap designs. Extensive pressure data was collected to provide a base data set for comparison with computational design codes and to allow a better understanding of the flow over vortex flaps. The results indicated that vortex flaps can be designed which will contain the leading edge vortex with no spillage onto the wing upper surface. However, the tests also showed that flaps designed without accounting for flap thickness will not be optimum and the result can be oversized flaps, early flap vortex reattachment and a second separation and vortex at the wing/flap hinge line.

Marchman, J. F., III↗
NASA NTRS1976

Reflection-plane tests of spoilers on an advanced technology wing with a large Fowler flap

Wind tunnel experiments were conducted to determine the effectiveness of spoilers applied to a finite-span wing which utilizes the GA(W)-1 airfoil section and a 30% chord full-span Fowler flap. A series of spoiler cross sectioned shapes were tested utilizing a reflection-plane model. Five-component force characteristics and hinge moment measurements were obtained. Results confirm earlier two-dimensional tests which showed that spoilers could provide large lift increments at any flap setting, and that spoiler control reversal tendencies could be eliminated by providing a vent path from lower surface to upper surface. Performance penalties due to spoiler leakage airflow were measured.

Wentz, W. H., Jr.↗
NASA NTRS1946

Characteristics of a Sealed Internally Balanced Aileron from Tests of a 1/4-Scale Partial-Span Model of the Republic XF-12 Airplane in the Langley 19-Foot Pressure Tunnel

This paper presents the results of the aileron investigation and includes rolling-moment, yawing-moment, and aileron hinge-moment coefficients and pressure coefficients across the aileron-balance seal through a range of angle of attack, tab deflection, and aileron deflection with flaps neutral and deflected 20 degrees and 55 degrees. Some of the effects of wing roughness and balance seal leakage on the aileron and tab characteristics are also presented.

Graham, Robert R.↗
NASA NTRS2012

High-Reynolds Number Circulation Control Testing in the National Transonic Facility

A new capability to test active flow control concepts and propulsion simulations at high Reynolds numbers in the National Transonic Facility at the NASA Langley Research Center is being developed. The first active flow control experiment was completed using the new FAST-MAC semi-span model to study Reynolds number scaling effects for several circulation control concepts. Testing was conducted over a wide range of Mach numbers, up to chord Reynolds numbers of 30 million. The model was equipped with four onboard flow control valves allowing independent control of the circulation control plenums, which were directed over a 15% chord simple-hinged flap. Preliminary analysis of the uncorrected lift data showed that the circulation control increased the low-speed maximum lift coefficient by 33%. At transonic speeds, the circulation control was capable of positively altering the shockwave pattern on the upper wing surface and reducing flow separation. Furthermore, application of the technique to only the outboard portion of the wing demonstrated the feasibility of a pneumatic based roll control capability.

Milholen, William E., II↗
NASA NTRS1957

Loads Due to Controls at Transonic and Low Supersonic Speeds

Some results of recent experimental investigations at supersonic and transonic speeds are presented to show the present status in the estimation of load distributions on controls and adjacent wing surfaces resulting from the deflection of flap controls and spoiler controls. The results indicate that the development of methods for predicting loads associated with controls has not kept pace with the acquisition of experimental data. At low supersonic speeds sweeping the hinge line induces strong three-dimensional-flow characteristics which cannot be treated by the simplified methods previously developed for controls without sweep. At transonic speeds the estimation of loads associated with controls must usually be dependent upon experimental information inasmuch as the latest attempts to predict chordwise and spanwise loadings have met with only limited success.

West, F. E, Jr↗