Search NASA⌕ Search

SEARCH · Search NASA

Results for “WING TIP CONTROLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Comparison of Aileron Control Characteristics as Determined in Flight Tests of P-36, P-40, Spitfire, and Hurricane Pursuit Airplanes

The Army Air Force has made available several pursuit-type airplanes for quantitative investigation of their flying and handling qualities. One Item of special interest obtained from the results of the investigation is a comparison of the aileron control characteristics of the P-36, P-40, Hawker Hurricane, and Supermarine Spitfire airplanes. Figure 1 shows the design characteristics of the ailerons and the control sticks of the four airplanes. Aileron effectiveness may be expressed in terms of the helix angle generated by the wing tip in a steady roll. This angle is given by the expression pb/2V, where p is the rolling velocity, b the wing span, and V the true airspeed, expressed in consistent units. This quantity is convenient to use because, although it does not rep resent directly the rolling velocity of airplanes of different spans or airplanes operating at different speeds, it provides a satisfactory basis for computing the rate of roll and the time required to bank a given amount under any given set of conditions. The ratio of pb/2V obtained in any roll to the maximum value reached with full aileron deflection indicates the fraction of the maximum aileron travel that was reached. A complete discussion of this criterion for aileron effectiveness is given in reference 1. The aileron effectiveness of the various airplanes is compared in the following table on the basis of the response obtained with stick forces of 30 and 5 pounds. A force of 30 pounds is somewhat less than the greatest stick force exerted by the pilot. Repeated flight measurements have shown, however, that this force is a reasonable upper limit for maneuvering at high speeds.

Phillips, William H.↗

A Flight Study of the Conversion Maneuver of a Tilt-Duct VTOL Aircraft

Flight records are presented from an early flight test of a wing-tip mounted tilting-ducted-fan, vertical-take-off and landing (VTOL) aircraft configuration. Time histories of the aircraft motions, control positions, and duct pitching-moment variation are presented to illustrate the characteristics of the aircraft in hovering, in conversion from hovering to forward flight, and in conversion from forward flight to hovering. The results indicate that during essentially continuous slow level- flight conversions, this aircraft experiences excessive longitudinal trim changes. Studies have shown that the large trim changes are caused primarily by the variation of aerodynamic moments acting on the duct units. Action of the duct-induced downwash on the horizontal stabilizer during the conversion also contributes to the longitudinal trim variations. Time histories of hovering and slow vertical descent in the final stages of landing in calm air show angular motions of the aircraft as great as +/- 10 deg. about all axes. Stick and pedal displacements required to control the aircraft during the landing maneuver were on the order of 50 to 60 percent of the total travel available.

Tapscott, Robert J.↗

Outdoor test stand performance of a convertible engine with variable inlet guide vanes for advanced rotorcraft propulsion

A variable inlet guide van (VIGV) type convertible engine that could be used to power future high-speed rotorcraft was tested on an outdoor stand. The engine ran stably and smoothly in the turbofan, turboshaft, and dual (combined fan and shaft) power modes. In the turbofan mode with the VIGV open fuel consumption was comparable to that of a conventional turbofan engine. In the turboshaft mode with the VIGV closed fuel consumption was higher than that of present turboshaft engines because power was wasted in churning fan-tip airflow. In dynamic performance tests with a specially built digital engine control and using a waterbrake dynamometer for shaft load, the engine responded effectively to large steps in thrust command and shaft torque. Previous mission analyses of a conceptual X-wing rotorcraft capable of 400-knot cruise speed were revised to account for more fan-tip churning power loss than was originally estimated. The new calculations confirm that using convertible engines rather than separate lift and cruise engines would result in a smaller, lighter craft with lower fuel use and direct operating cost.

Mcardle, Jack G.↗

The convertible engine: A dual-mode propulsion system

A variable inlet guide vane (VIGV) convertible engine that could be used to power future high-speed rotorcraft was tested on an outdoor stand. The engine ran stably and smoothly in the turbofan, turboshaft, and dual (combined fan and shaft) power modes. In the turbofan mode with the VIGV open, fuel consumption was comparable to that of a conventional turbofan engine. In the turboshaft mode with the VIGV closed, fuel consumption was higher than that of present turboshaft engines because power was wasted in churning fan-tip air flow. In dynamic performance tests with a specially built digital engine control and using a waterbrake dynamometer for shaft load, the engine responded effectively to large steps in thrust command and shaft torque. Previous mission analyses of a conceptual X-wing rotorcraft capable of 400-knot cruise speed were revised to account for more fan-tip churning power loss that was originally estimated. The calculations confirm that using convertible engines rather than separate life and cruise engines would result in a smaller, lighter craft with lower fuel use and direct operating cost.

Mcardle, Jack G.↗

Supersonic aerodynamic characteristics of a circular body Earth-to-Orbit vehicle

The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.

Ware, George M.↗

Impact of subsonic aerodynamic considerations on a space shuttle booster configuration

Considerations of cruise-back efficiency and subsonic flying qualities are shown to have resulted in a configuration with an aft high wing of moderate aspect ratio and with vertical tails located at the wing tips. The need to protect the air breathing engines during ascent and reentry and the desire for a low trim penalty longitudinal control surface led to consideration of a jet-flap canard. The advantages of this application of STOL technology to a space system are examined and the results of both wind tunnel tests and flight simulations are discussed. Since the use of the jet-flap canard concept offers the potential for a minimum weight vehicle, a proposed technology development program is outlined in order that the full benefit of this concept may be realized.

Roensch, R. L.↗

Measurements on wing-tip blowing

The aerodynamics of a rectangular wing with a jet exhausting in the spanwise direction from the tips has been explored experimentally. By effectively changing the span of the wing as well as outwardly displacing the tip vortices, such jets can induce aerodynamic forces that could be used for roll and lateral control of aircraft. The concept has been investigated for a variety of jet intensities, angles of attack, and aspect ratios. The results appear to confirm theoretically predicted scaling laws for lift gain and moment generation due to blowing.

Tavella, D.↗

Turbine Engine Clearance Control Systems: Current Practices and Future Directions

Improved blade tip sealing in the high pressure compressor (HPC) and high pressure turbine (HPT) can provide dramatic reductions in specific fuel consumption (SFC), time-on-wing, compressor stall margin, and engine efficiency as well as increased payload and mission range capabilities. Maintenance costs to overhaul large commercial gas turbine engines can easily exceed $1M. Engine removal from service is primarily due to spent exhaust gas temperature (EGT) margin caused mainly by the deterioration of HPT components. Increased blade tip clearance is a major factor in hot section component degradation. As engine designs continue to push the performance envelope with fewer parts and the market drives manufacturers to increase service life, the need for advanced sealing continues to grow. A review of aero gas turbine engine HPT performance degradation and the mechanisms that promote these losses are discussed. Benefits to the HPT due to improved clearance management are identified. Past and present sealing technologies are presented along with specifications for next generation engine clearance control systems.

Lattime, Scott B.↗

Tests of a Triangular Wing of Aspect Ratio 2 in the Ames 12-foot Pressure Wind Tunnel III : the Effectiveness and Hinge Moments of a Skewed Wing-tip Flap

Results of wind-tunnel tests of a semispan model of a triangular wing of aspect ratio 2 with a skewed wing-tip flap are presented. Lift, drag, pitching-moment, and hinge-moment data are included for subsonic Mach numbers up to 0.95. The flap showed extremely high hinge moments and low effectiveness as a longitudinal control. Although less affected by compressibility, this flap is indicated to be inferior to a constant-chord flap when applied to this triangular wing.

MACH NUMBER EFFECTS - COMPLETE WINGS↗

Comparison of noise prediction for the X-wing system and a conventional rotor in hover

Analytic predictions of X-wing rotor noise levels in hover without circulation control are presented and compared with measured data at two observer locations. Agreement of predictions and data is best in the rotor plane, due to the dominance of thickness noise terms. Predictions are made for the X-wing and a conventional type rotor system and are compared at two locations at the same tip speed and at each rotor's design tip speed. The acoustic signal of the X-wing is more heavily influenced by thickness noise terms than the conventional rotor. The comparison of each rotor's noise levels depends on the observer location and the amount of circulation control blowing employed.

Martin, R. M.↗

A Transonic Wind-Tunnel Investigation of the Performance and of the Static Stability and Control Characteristics of a Model of a Fighter-Type Airplane which Embodies Partial Body Indentation

An investigation was conducted to obtain the aerodynamic characteristics of a model of a fighter-type airplane embodying partial body indentation. The wing had an aspect ratio of 4, taper ratio of 0.5, 35 deg sweepback of the 0.25-chord line, and a modified NACA 65A006 airfoil section at the root and a modified NACA 65A004 airfoil section at the tip. The fuselage has been indented in the region of the wing in order to obtain a favorable area distribution. The results reported herein consist of the performance and of the static longitudinal and lateral stability and control characteristics of the complete model. The Mach number range extended from 0.60 to 1.13, and the corresponding Reynolds number based on the wing mean aerodynamic chord varied from 1.77 x 10(exp 6) to 2.15 x 10(exp 6). The drag rise for both the cambered leading edge and symmetrical wing sections occurred at a Mach number of 0.95. Certain local modifications to the body which further improved the distribution of cross-sectional area gave additional reductions in drag at a Mach number of 1.00. The basic configuration indicated a mild pitch-up tendency at lift coefficients near 0.70 for the Mach number range from 0.80 to 0.90; however, the pitch-up instability may not be too objectionable on the basis of dynamic-stability considerations. The basic configuration indicated positive directional stability and positive effective dihedral through the angle-of-attack range and Mach number range with the exception of a region of negative effective dihedral at low lifts at Mach numbers of 1.00 and slightly above.

Bielat, Ralph P.↗

Experimental Results of Winglets on First, Second, and Third Generation Jet Transports

Results of wind tunnel investigations of four jet transport configurations representing both narrow and wide-body configurations and also a future advanced aerodynamic configuration are presented including performance and wing root bending moment data. The effects of winglets on the aerodynamic characteristics throughout the flight envelope were studied. The results indicate that winglets improved the cruise lift to drag ratio between 4 and 8 percent, depending on the transport configuration. The data also indicate that ratios of relative aerodynamic gain to relative structural weight penalty for winglets are 1.5 to 2.5 times those for wing-tip extensions. Over the complete range of flight conditions, winglets produce no adverse effects on buffet onset, lateral-directional stability, and aileron control effectiveness.

Flechner, S. G.↗

Wind-Tunnel Tests of the 1/25-Scale Powered Model of the Martin JRM-1 Airplane. IV - Tests with Ground Board and with Modified Wing and Hull - TED No. NACA 232: Tests with Ground Board and with Modified Wing and Hull, TED No. NACA 232 - Part 4

Wind-tunnel tests were made of a 1/25 scale model of the Martin JRM-1 airplane to determine: (1) The longitudinal stability and control characteristics of the JRM-1 model near the water and lateral and directional stability characteristics with power while moving on the surface of the water, the latter being useful for the design of tip floats; (2) The stability and stalling characteristics of the wing with a modified airfoil contour; (3) Stability characteristics of a hull of larger design gross weight; The test results indicated that the elevator was powerful enough to trim the original model in a landing configuration at any lift coefficient within the specified range of centers of gravity. The ground-board tests for evaluating the aerodynamic forces and moments on an airplane in a simulated cross wind indicate a high dihedral effect in the presence of the ground board and, consequently, during low-speed taxying and take-off, large overturning moments would result which would have to be overcome by the tip floats.

Lockwood, Vernard E.↗

Rotor/wing aerodynamic interactions in hover

An experimental and theoretical investigation of rotor/wing aerodynamic interactions in hover is described. The experimental investigation consisted of both a large-scale and small-scale test. A 0.658-scale, V-22 rotor and wing was used in the large-scale test. Wind download, wing surface pressure, rotor performance, and rotor downwash data from the large-scale test are presented. A small-scale experiment was conducted to determine how changes in the rotor/wing geometry affected the aerodynamic interactions. These geometry variations included the distance between the rotor and wing, wing incidence angle, and configurations both with the rotor axis at the tip of the wing (tilt rotor configuration) and with the rotor axis at the center of the wing (compound helicopter configuration). A wing with boundary-layer control was also tested to evaluate the effect of leading and trailing edge upper surface blowing on the wing download. A computationally efficient, semi-empirical theory was developed to predict the download on the wing. Finally, correlations between the theoretical predictions and test data are presented.

Felker, F. F.↗

Rotor/wing aerodynamic interactions in hover

An experimental and theoretical investigation of rotor/wing aerodynamic interactions in hover is described. The experimental investigation consisted of both a large-scale and small-scale test. A 0.658-scale, V-22 rotor and wing was used in the large-scale test. Wind download, wing surface pressure, rotor performance, and rotor downwash data from the large-scale test are presented. A small-scale experiment was conducted to determine how changes in the rotor/wing geometry affected the aerodynamic interactions. These geometry variations included the distance between the rotor and wing, wing incidence angle, and configurations both with the rotor axis at the tip of the wing (tilt rotor configuration) and with the rotor axis at the center of the wing (compound helicopter oonfiguration). A wing with boundary-layer control was also tested to evaluate the effect of leading and trailing edge upper surface blowing on the wing download. A computationally efficient, semi-empirical theory was developed to predict the download on the wing. Finally, correlations between the theoretical predictions and test data are presented.

Felker, F. F.↗

An Evaluation of the Roll-Rate Stabilization System of the Sidewinder Missile at Mach Numbers from 0.9 to 2.3

A linear stability analysis and flight-test investigation has been performed on a rolleron-type roll-rate stabilization system for a canard-type missile configuration through a Mach number range from 0.9 to 2.3. This type damper provides roll damping by the action of gyro-actuated uncoupled wing-tip ailerons. A dynamic roll instability predicted by the analysis was confirmed by flight testing and was subsequently eliminated by the introduction of control-surface damping about the rolleron hinge line. The control-surface damping was provided by an orifice-type damper contained within the control surface. Steady-state rolling velocities were at all times less than 1 radian per second between the Mach numbers of 0.9 to 2.3 on the configurations tested. No adverse longitudinal effects were experienced in flight because of the tendency of the free-floating rollerons to couple into the pitching motion at the low angles of attack and disturbance levels investigated herein after the introduction of control-surface damping.

Nason, Martin L.↗

Experimental results of winglets on first, second, and third generation jet transports

The results of wind tunnel investigations of winglets on four jet transport configurations are presented. Performance and wing root bending moment data were given. Additionally, detailed aerodynamic characteristics are presented at the design condition and also at several off design conditions for one configuration. Results of the investigations indicate that the winglets improve the cruise lift to drag ratio between 4 and 8 percent. These data also show that the ratios of relative aerodynamic gain to relative structural weight penalty for winglets are 1.5 to 2.5 times the ratios for wing tip extensions. The comprehensive investigation of the effects of winglets indicated that winglets produce no adverse effects on buffet onset, lateral directional stability, and aileron control effectiveness.

Flechner, S. G.↗

Flight Investigation of a Roll-stabilized Missile Configuration at Varying Angles of Attack at Mach Numbers Between 0.8 and 1.79

A missile research model was flown at supersonic speed to determine the quality of automatic roll stabilization at varying angles of attack. Aerodynamic rolling and pitching derivatives were determined from the flight record. It was concluded that the combination of the gyro-actuated automatic pilot with wing-tip ailerons provided adequate roll stabilization under conditions encountered in flight.

INSTRUMENTS↗