Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wall Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

The Lag Model, a Turbulence Model for Wall Bounded Flows Including Separation

A new class of turbulence model is described for wall bounded, high Reynolds number flows. A specific turbulence model is demonstrated, with results for favorable and adverse pressure gradient flowfields. Separation predictions are as good or better than either Spalart Almaras or SST models, do not require specification of wall distance, and have similar or reduced computational effort compared with these models.

Olsen, Michael E.↗

On the Modeling of Wall Heat Flux Partitioning in Subcooled Flow Boiling

Accurate prediction of void distribution in reactor coolant channels at subcooled boiling conditions is an important factor in the analysis of the operating conditions of both pressurized water reactors (PWRs) and boiling water reactors (BWRs). Its importance arises from purely thermal-hydraulic considerations (thermal limits, CRUD formation, etc.) and the impact of void reactivity feedback on core neutronics. A mechanistic multidimensional model of subcooled boiling was originally developed by Kurul and Podowski. Whereas this model has been implemented in several commercial CFD codes and successfully used in computer simulations of flow and phase distributions in the coolant channels of light water reactor, additional new modeling aspects of forced-convection subcooled boiling heat transfer have been investigated in recent studies. The purpose of this paper is to formulate a modified model of wall heat flux partitioning, which allows for capturing and quantifying the effect of simultaneous evaporation and condensation at the heated wall on the net evaporation rate and wall temperature. The new model has been implemented in the NPHASE-CMFD code, numerically tested and validated against experimental data. A mechanistic wall heat flux partitioning model for subcooled flow boiling has been presented. This model has been combined with extensively tested models of interfacial mass, momentum and energy transfer terms. It turns out that the model predictions of the wall temperature and void fraction are in good agreement with the experimental data of reference. Future work will focus on the continuation of model validation against experimental data, and on extending its scope to include the phenomena governing departure from nucleate boiling. (authors)

42 ENGINEERING↗

Effects of Artificial Viscosity on the Accuracy of High-reynolds-number Kappa-epsilon Turbulence Model

Wall functions, as used in the typical high Reynolds number k-epsilon turbulence model, can be implemented in various ways. A least disruptive method (to the flow solver) is to directly solve for the flow variables at the grid point next to the wall while prescribing the values of k and epsilon. For the centrally-differenced finite-difference scheme employing artificial viscocity (AV) as a stabilizing mechanism, this methodology proved to be totally useless. This is because the AV gives rise to a large error at the wall due to too steep a velocity gradient resulting from the use of a coarse grid as required by the wall function methodology. This error can be eliminated simply by extrapolating velocities at the wall, instead of using the physical values of the no-slip velocities (i.e. the zero value). The applicability of the technique used in this paper is demonstrated by solving a flow over a flat plate and comparing the results with those of experiments. It was also observed that AV gives rise to a velocity overshoot (about 1 percent) near the edge of the boundary layer. This small velocity error, however, can yield as much as 10 percent error in the momentum thickness. A method which integrates the boundary layer up to only the edge of the boundary (instead of infinity) was proposed and demonstrated to give better results than the standard method.

Chitsomboon, Tawit↗

Fermion mass hierarchy and phenomenology in the 5D Domain Wall Standard Model

We have recently proposed a setup of the “Domain-Wall Standard Model” in 5D spacetime, where all the Standard Model (SM) fields are localized in certain domains of the extra 5th dimension. Utilizing this setup, we attempt to solve the fermion mass hierarchy problem of the SM. The mass hierarchy can be naturally explained by suitably distributing the fermions in different positions along the extra dimension. Due to these different localization points, the effective 4D gauge couplings of Kaluza-Klein (KK) mode gauge bosons to the SM fermions become non-universal. As a result, our model is severely constrained by the Flavor Changing Neutral Current (FCNC) measurements. We find two interesting cases in which our model is phenomenologically viable: (1) the KK-mode of the SM gauge bosons are extremely heavy and unlikely to be produced at the Large Hadron Collider (LHC), while future FCNC measurements can reveal the existence of these heavy modes. (2) the width of the localized SM fermions is very narrow, leading to almost universal 4D KK-mode gauge couplings. In this case, the FCNC constraints can be easily avoided even if a KK gauge boson mass lies at the TeV scale. Such a light KK gauge boson can be searched at the LHC in the near future.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quark number susceptibility and QCD phase transition in the predictive soft-wall AdS/QCD model with finite temperature

Based on the infrared improved soft-wall AdS/QCD model which can lead to a consistent prediction for the mass spectra of light resonance mesons, we extend it to the finite temperature system and carry out the calculation for the quark number susceptibility with finite quark mass. As a consequence, we show that the quark number susceptibility grows rapidly with a continuous blowup in a narrow temperature interval as the temperature increases, and there is a peak when the temperature is around T{approx_equal}160{approx}190 MeV depending slightly on the models. The resulting critical temperature is about 170 MeV, which agrees remarkably with the lattice QCD calculation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Progress Towards a Cartesian Cut-Cell Method for Viscous Compressible Flow

We present preliminary development of an approach for simulating high Reynolds number steady compressible flow in two space dimensions using a Cartesian cut-cell finite volume method. We consider both laminar and turbulent flow with both low and high cell Reynolds numbers near the wall. The approach solves the full Navier-Stokes equations in all cells, and uses a wall model to address the resolution requirements near boundaries and to mitigate mesh irregularities in cut cells. We present a quadratic wall model for low cell Reynolds numbers. At high cell Reynolds numbers, the quadratic is replaced with a newly developed analytic wall model stemming from solution of a limiting form of the Spalart-Allmaras turbulence model which features a forward evaluation for flow velocity and exactly matches characteristics of the SA turbulence model in the field. We develop multigrid operators which attain convergence rates similar to inviscid multigrid. Investigations focus on preliminary verification and validation of the method. Flows over flat plates and compressible airfoils show good agreement with both theoretical results and experimental data. Mesh convergence studies on sub- and transonic airfoil flows show convergence of surface pressures with wall spacings as large as approx.0.1% chord. With the current analytic wall model, one or two additional refinements near the wall are required to obtain mesh converged values of skin friction.

Berger, Marsha↗

The soft-wall standard model

We explore the possibility of modeling electroweak physics in a warped extra dimension with a soft wall. The infrared boundary is replaced with a smoothly varying dilaton field that provides a dynamical spacetime cutoff. We analyze gravity, gauge fields, and fermions in the soft-wall background and obtain a discrete spectrum of Kaluza-Klein states which can exhibit linear Regge-like behavior. Bulk Yukawa interactions give rise to nonconstant fermion mass terms, leading to fermion localization in the soft-wall background and a possible explanation of the standard model flavor structure. Furthermore we construct electroweak models with custodial symmetry, where the gauge symmetry is broken with a bulk Higgs condensate. The electroweak constraints are not as stringent as in hard-wall models, allowing Kaluza-Klein masses of order the TeV scale.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Modeling near wall effects in second moment closures by elliptic relaxation

The elliptic relaxation model of Durbin (1993) for modeling near-wall turbulence using second moment closures (SMC) is compared to DNS data for a channel flow at Re(sub t) = 395. The agreement for second order statistics and even the terms in their balance equation is quite satisfactory, confirming that very little viscous effects (via Kolmogoroff scales) need to be added to the high Reynolds versions of SMC for near-wall-turbulence. The essential near-wall feature is thus the kinematic blocking effect that a solid wall exerts on the turbulence through the fluctuating pressure, which is best modeled by an elliptic operator. Above the transition layer, the effect of the original elliptic operator decays rapidly, and it is suggested that the log-layer is better reproduced by adding a non-homogeneous reduction of the return to isotropy, the gradient of the turbulent length scale being used as a measure of the inhomogeneity of the log-layer. The elliptic operator was quite easily applied to the non-linear Craft & Launder pressure-strain model yielding an improved distinction between the spanwise and wall normal stresses, although at higher Reynolds number (Re) and away from the wall, the streamwise component is severely underpredicted, as well as the transition in the mean velocity from the log to the wake profiles. In this area a significant change of behavior was observed in the DNS pressure-strain term, entirely ignored in the models.

Laurence, D.↗

One-equation near-wall turbulence modeling with the aid of direct simulation data

The length scales appearing in the relations for the eddy viscosity and dissipation rate in one-equation models were evaluated from direct numerical (DNS) simulation data for developed channel and boundary-layer flow at two Reynolds numbers each. To prepare the ground for the evaluation, the distribution of the most relevant mean-flow and turbulence quantities is presented and discussed, also with respect to Reynolds-number influence and to differences between channel and boundary-layer flow. An alternative model is tested as near wall component of a two-layer model by application to developed-channel, boundary-layer and backward-facing-step flows.

Rodi, W.↗

Prediction for the mass spectra of resonance mesons in the soft-wall AdS/QCD model with a modified 5D metric

A soft-wall anti-de Sitter/QCD model with a modified five-dimensional metric at the infrared region is constructed to obtain a nontrivial dilaton solution, which incorporates the chiral symmetry breaking and linear confinement. By taking the pion mass and decay constant as two input mass scales, the resulting predictions for the resonance states of pseudoscalar, scalar, vector, and axial-vector mesons agree remarkably with the experimentally confirmed resonance states. The effects of the quartic interaction term are investigated by taking an appropriate sign and magnitude for maintaining the stability of the bulk scalar potential. It is shown that such a simply modified soft-wall anti-de Sitter/QCD model can lead to a consistent prediction for the mass spectra of resonance states in the pseudoscalar, scalar, vector, and axial-vector mesons; the agreement with the experimental data is found to be better than 10% for the excited meson states. The resulting pion form factor also agrees well with the experimental data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Analytical model of wall forces produced by kink perturbations in tokamaks

Analytical model of the electromagnetic forces produced by kink modes on the tokamak wall [H. R. Strauss et al., Phys. Plasmas 17, 082505 (2010)] is revisited. One of the main conclusions of the mentioned paper is that the largest force occurs at γτ{sub w}≈1, where γ is the kink growth rate and τ{sub w} is the wall penetration time. In the present study, a similar approach is developed under less restrictive assumptions on the plasma and dynamics of perturbation, and a different result is obtained: the force increases with γ and must be maximal at γτ{sub w}→∞. Additionally, the dependence of its amplitude on the plasma parameters is clarified. All distinctions and their reasons are explained in detail. The analysis is performed in the cylindrical model incorporating a resistive wall treated without traditional thin-wall constraints and covering therefore a full range in γτ{sub w}. It is applicable to either locked or rotating modes. Estimates of the sideways force are presented and compared with earlier forecasts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Domain-Wall Standard Model in non-compact 5D and LHC phenomenology

We propose a framework to construct “Domain-Wall Standard Model” in a non-compact 5-dimensional spacetime, where all the Standard Model (SM) fields are localized in certain domains of the 5th dimension and the SM is realized as a 4-dimensional effective theory without any compactification for the 5th dimension. In this context, we investigate the collider phenomenology of the Kaluza–Klein (KK) modes of the SM gauge bosons and the current constraints from the search for a new gauge boson resonance at the Large Hadron Collider Run-2. The couplings of the SM fermions with the KK-mode gauge bosons depend on the configuration of the SM fermions in the 5-dimensional bulk. This “geometry” of the model can be tested at the future Large Hadron Collider experiment, once a KK-mode of the SM gauge boson is discovered.

Astronomy & Astrophysics↗

Fermion masses and mixing in a 4+1 dimensional SU(5) domain-wall brane model

We study the fermion mass and mixing hierarchy problems within the context of the SU(5) 4+1d domain-wall brane model of Davies, George, and Volkas. In this model, the ordinary fermion mass relations of SU(5) grand unified theories are avoided, since the masses are proportional to overlap integrals of the profiles of the electroweak Higgs and the chiral components of each fermion, which are split into different 3+1d hyperplanes according to their hypercharges. We show that the fermion mass hierarchy without electroweak mixing can be generated naturally from these splittings, that generation of the Cabibbo-Kobayashi-Maskawa matrix looks promising, and that the Cabibbo angle, along with the mass hierarchy, can be generated for the case of Majorana neutrinos from a more modest hierarchy of parameters. We also show that, under some assumptions made on the parameter space, the generation of realistic lepton mixing angles is not possible without fine-tuning, which argues for a flavor symmetry to enforce the required relations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DNS and modeling of the interaction between turbulent premixed flames and walls

The interaction between turbulent premixed flames and walls is studied using a two-dimensional full Navier-Stokes solver with simple chemistry. The effects of wall distance on the local and global flame structure are investigated. Quenching distances and maximum wall heat fluxes during quenching are computed in laminar cases and are found to be comparable to experimental and analytical results. For turbulent cases, it is shown that quenching distances and maximum heat fluxes remain of the same order as for laminar flames. Based on simulation results, a 'law-of-the-wall' model is derived to describe the interaction between a turbulent premixed flame and a wall. This model is constructed to provide reasonable behavior of flame surface density near a wall under the assumption that flame-wall interaction takes place at scales smaller than the computational mesh. It can be implemented in conjunction with any of several recent flamelet models based on a modeled surface density equation, with no additional constraints on mesh size or time step.

Poinsot, T. J.↗

Transient liquid-crystal technique used to produce high-resolution convective heat-transfer-coefficient maps

In this transient technique the preheated isothermal model wall simulates the classic one-dimensional, semi-infinite wall heat transfer conduction problem. By knowing the temperature of the air flowing through the model, the initial temperature of the model wall, and the surface cooling rate measured at any location with time (using the fast-response liquid-crystal patterns recorded on video tape), the heat transfer coefficient can be calculated for the color isothermal pattern produced. Although the test was run transiently, the heat transfer coefficients are for the steady-state case. The upstream thermal boundary condition was considered to be isothermal. This transient liquid-crystal heat-transfer technique was used in a transient air tunnel in which a square-inlet, 3-to-1 exit transition duct was placed. The duct was preheated prior to allowing room temperature air to be suddenly drawn through it. The resulting isothermal contours on the duct surfaces were revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record was made of the temperature and time data for all points on the duct surfaces during each test. The duct surfaces were uniformly heated using two heating systems: the first was an automatic temperature-controlled heater blanket completely surrounding the test duct like an oven, and the second was an internal hot-air loop through the inside of the test duct. The hot-air loop path was confined inside the test duct by insulated heat dams located at the inlet and exit ends of the test duct. A recirculating fan moved hot air into the duct inlet, through the duct, out of the duct exit, through the oven, and back to the duct inlet. The temperature nonuniformity of the test duct model wall was held very small. Test results are reported for two inlet Reynolds numbers of 200,000 and 1,150,000 (based on the square-inlet hydraulic diameter) and two free-stream turbulence intensities of about 1 percent, which is typical of wind tunnels, and up to 20 percent (using a grid), which is typical of real engine conditions.

Hippensteele, Steven A.↗