Search NASA⌕ Search

SEARCH · Search NASA

Results for “Well Test Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Preliminary Results from an Experimental Assessment of a Natural Laminar Flow Design Method

A 5.2% scale semispan model of the new Common Research Model with Natural Laminar Flow (CRM-NLF) was tested in the National Transonic Facility (NTF) at the NASA Langley Research Center. The model was tested at transonic cruise flight conditions with Reynolds numbers based on mean aerodynamic chord ranging from 10 to 30 million. The goal of the test was to experimentally validate a new design method, referred to as Crossflow Attenuated NLF (CATNLF), which shapes airfoils to have pressure distributions that delay transition on wings with high sweep and Reynolds numbers. Additionally, the test aimed to characterize the NTF laminar flow testing capabilities, as well as establish best practices for laminar flow wind tunnel testing. Preliminary results regarding the first goal of validating the new design method are presented in this paper. Experimental data analyzed in this assessment include surface pressure data and transition images. The surface pressure data acquired during the test agree well with computational fluid dynamics (CFD) results. Transition images at a variety of Reynolds numbers and angles of attack are presented and compared to computational transition predictions. The experimental data are used to assess transition due to a turbulent attachment line, as well as crossflow and Tollmien-Schlichting modal instabilities. Preliminary results suggest the CATNLF design method is successful at delaying transition on wings with high sweep. Initial analysis of the transition front images showed transition Reynolds numbers that exceed historic experimental values at similar sweep angles. , section lift

Lynde, Michelle N.↗
DOE OSTI2025

Modeling aerosol bolus inhalations in the human lung with the multiple path particle deposition model: Comparison with experimental data

Existing one-dimensional (1D) models of aerosol dosimetry often ignore mixing mechanisms of inhaled aerosols during their transport in the lung. This mixing or aerosol dispersion results from different physical mechanisms in different regions of the lung. It is a higher order effect, which cannot be directly captured in 1D modeling approaches, and thus is sometimes modeled as a diffusive process. Here, in this study, we improved our recently developed alveolar mixing module incorporated in the multiple path particle dosimetry model (MPPD) to account for flow irreversibility and particle trapping in the alveolar spaces, as well as mixing occurring in the tracheobronchial region. This new version of MPPD was coupled with CFPD-based predictions of aerosol bolus dispersion in the oral airway. The model was used to predict the deposition, dispersion, and mode shift of aerosol bolus inhaled at different penetration depths within the lung for breathing patterns and particle size matching those used in a previous experimental study (Darquenne et al., 2016). Even though a quite simplified approach was used, the computations appear to describe subject-specific and test-specific experimental data reasonably well. The proposed combined dispersion-deposition model can be a useful tool for targeted drug delivery and also for exposure health risk assessment.

MPPD↗
NASA NTRS2002

Transients in Pacific/North American Plate Boundary Deformation: Synthesis and Modeling of GPS and Borehole Strain Observations

This is the Final Technical Report on research conducted between 1 June 1997 and 14 September 2001 entitled "Transients in Pacific/North American plate boundary deformation: Synthesis and modeling of GPS and borehole strain observations." As the project title implies, our effort involved a geodetic study of strain transients, i.e., temporal variations in deformation rates, that occur within plate boundary zones and their relationship to earthquakes and plate motions. Important transients occur during and following large earthquakes, and there are also strain transients not apparently associated with earthquakes. A particularly intriguing class of transients, for which there is a modest but growing list of examples, are preseismic anomalies. Such earthquake precursors, if further documented and understood, would have obvious importance for earthquake hazard mitigation. Because the timescales for these diverse transients range over at least 6 orders of magnitude (minutes to years), no single geodetic technique is optimum. We therefore undertook a systematic synthesis of Global Positioning Satellite (GPS) and borehole strainmeter data in three areas in California where there are adequate numbers of both types of instruments (or their equivalent): the San Francisco Bay region (within the Bay Area Regional Deformation network), southern California (within the Southern California Integrated GPS Network), and Parkfield (where a two-color laser system provides a proxy for continuous GPS measurements). An integral component of our study was the elucidation of the physical mechanisms by which such transients occur and propagate. We therefore initiated the development of multiple forward models, using two independent approaches. In the first, we explored the response to specified earthquake slip in viscoelastic models that incorporated failure criteria and the geometry of major faults in California. In the second approach, we examined the dynamical response of a complex rheological medium to the application of a far-field stress imposed by plate motions. The forward models were used both to gain insight into the range of strain transients to be expected under different assumed mechanical conditions and to develop representations for strain fields that allow GPS, borehole, and other strain data to be combined in a self-consistent, yet well-determined, manner. The models also provided a basis for hypothesis testing, by which data from a strain transient well characterized by GPS and borehole observations were utilized to distinguish among competing candidates for the causative physical mechanism and the governing physical characteristics. During the three years of this project, continued to a fourth year through a no-cost extension of the grant, we published 14 papers and presented or co-authored 37 papers at national scientific meetings.

Solomon, Sean C.↗
NASA NTRS2021

Numerical Validation of Composite Panel Impact Tests

Researchers have met the challenge of modeling impact events involving composite targets for a variety of applications in a variety of ways. In this paper, the theory and implementation details of an orthotropic visco-elastic-visco-plastic material model with strain rate dependence are discussed. The model is driven by experimental data from quasi-static as well as high strain rate tests, and the data is used in defining the deformation, damage and failure sub-models. Validation data is generated by shooting a hollow 50 g Al-2024 projectile at different velocities against a flat panel target made of unidirectional composite material in a 16-ply [(0/90/45/-45)_(2)]_(S) layup. Explicit dynamic finite element analyses of four high speed tests involving one contained (projectile rebounded) and three uncontained (projectile penetrated) impact tests show that the developed material model and modeling techniques yield reasonable and acceptable predictions.

Orthotropic Composite↗
NASA NTRS1995

General Fluid System Simulation Program to Model Secondary Flows in Turbomachinery

The complexity and variety of turbomachinery flow circuits created a need for a general fluid system simulation program for test data anomaly resolution as well as design review. The objective of the paper is to present a computer program that has been developed to support Marshall Space Flight Center's turbomachinery internal flow analysis efforts. The computer program solves for the mass. energy and species conservation equation at each node and flow rate equation at each branch of the network by a novel numerical procedure which is a combination of both Newton-Ralphson and successive substitution method and uses a thermodynamic property program for computing real gas properties. A generalized, robust, modular, and 'user-friendly' computer program has been developed to model internal flow rates, pressures, temperatures, concentrations of gas mixtures and axial thrusts. The program can be used for any network for compressible and incompressible flows, choked flow, change of phase and gaseous mixturecs. The code has been validated by comparing the predictions with Space Shuttle Main Engine test data.

Majumdar, Alok K.↗
NASA NTRS2001

Hyper-X Flight Engine Ground Testing for X-43 Flight Risk Reduction

Airframe-integrated scramjet engine testing has been completed at Mach 7 flight conditions in the NASA Langley 8-Foot High Temperature Tunnel as part of the NASA Hyper-X program. This test provided engine performance and operability data, as well as design and database verification, for the Mach 7 flight tests of the Hyper-X research vehicle (X-43), which will provide the first-ever airframe-integrated scramjet data in flight. The Hyper-X Flight Engine, a duplicate Mach 7 X-43 scramjet engine, was mounted on an airframe structure that duplicated the entire three-dimensional propulsion flowpath from the vehicle leading edge to the vehicle trailing edge. This model was also tested to verify and validate the complete flight-like engine system. This paper describes the subsystems that were subjected to flight-like conditions and presents supporting data. The results from this test help to reduce risk for the Mach 7 flights of the X-43.

Huebner, Lawrence D.↗
NASA NTRSDate not supplied

Kinetic Model Development of the Carbon Vapor Deposition Reactor to Predict Performance Versus Design

To enable complete closure of a Sabatier-based atmosphere revitalization system where oxygen recovery is predicated by carbon dioxide reduction to methane and water, there must be a means of recovering the hydrogen from the byproduct methane. Honeywell’s carbon vapor deposition (CVD) reactor is a potential technology that provides a thermochemical means by which methane decomposes at high temperatures (> 1,000 °C) into hydrogen, solid carbon, and a small percentage of hydrocarbons. This advanced methane pyrolysis reactor utilizes a carbon fiber substrate to capture and immobilize the solid pyrolytic carbon rather than allowing continuation toward undesirable soot. The CVD reactor is a highly dynamic system whose characteristic geometry changes while operating. The reactor model was developed to provide predictive performance assessment capabilities at different operating conditions, geometries, and configurations to aid in technology development. Modeling of the CVD reactor considered the multitude of simultaneous and interdependent physicochemical processes that are entailed, including: (1) the homogeneous gas-phase pyrolysis reactions, (2) the heterogeneous deposition reactions, and (3) the transport of gaseous species in the reactor domains. A 1-D CVD reactor model was developed based on a general packed-bed, axial-dispersion plug flow reactor model with a solid substrate balance to account for carbon deposition. The model includes 59 species and 243 reactions constituting the methane pyrolysis reaction network, carbon deposition, and interconversions of oxygenate species. The reactor model was compared to brassboard test data, where it was shown to be able to capture the pertinent physicochemical phenomena as evidenced by its agreement with short-duration run data (i.e., looking at different temperature and flow rate conditions), as well as trend agreement with the brassboard reactor’s long-duration test data. Recommendations are provided on further model development steps as well as its use cases.

Air Revitalization↗
NASA NTRS2018

Comparison of Iced Aerodynamic Measurements on a Swept Wing from Two Wind Tunnels

Artificial ice shapes of various geometric fidelity were tested on a wing model based on the Common Research Model. Low Reynolds number tests were conducted at Wichita State University's Beech Memorial Wind Tunnel, and high Reynolds number tests were conducted at ONERA's F1 wind tunnel. The aerodynamic performance data from the two facilities were compared at matched or similar Reynolds and Mach number to ensure that the results and trends observed at low Reynolds number could be applied and continued to high Reynolds number. For both clean and iced configurations, the data from Wichita State University and F1 agreed well at matched or similar Reynolds and Mach numbers. The lift and pitching moment curves agreed very well for most configurations. There appeared to be 0.2-0.3deg offset in the angle of attack between the Wichita State University and F1 data, possibly due to different flow angularities in the test sections of the two facilities. There was also an offset in the drag values between the two facilities from an unknown cause. Overall, the data compared very well between the low Reynolds number test at Wichita State University tunnel and the high Reynolds number test at F1. This indicated that data from the low Reynolds number tests could be used to understand iced-swept-wing aerodynamics at high Reynolds number.

Federal Aviation Administration↗
NASA NTRS1993

The 3-D CFD modeling of gas turbine combustor-integral bleed flow interaction

An advanced 3-D Computational Fluid Dynamics (CFD) model was developed to analyze the flow interaction between a gas turbine combustor and an integral bleed plenum. In this model, the elliptic governing equations of continuity, momentum and the k-e turbulence model were solved on a boundary-fitted, curvilinear, orthogonal grid system. The model was first validated against test data from public literature and then applied to a gas turbine combustor with integral bleed. The model predictions agreed well with data from combustor rig testing. The model predictions also indicated strong flow interaction between the combustor and the integral bleed. Integral bleed flow distribution was found to have a great effect on the pressure distribution around the gas turbine combustor.

Chen, D. Y.↗
NASA NTRS1972

Lifting-surface theory for calculating the loading induced on a wing by a flap

A method is described for using lifting-surface theory to obtain the pressure distribution on a wing with a trailing-edge flap or control surface. The loading has a logarithmic singularity at the flap edges, which may be determined directly by the method of matched asymptotic expansions. Expressions are given for the singular flap loading for various flap hinge line and side edge geometries, both for steady and unsteady flap deflection. The regular part of the flap loading must be obtained by inverting the lifting-surface-theory integral equation relating the pressure and the downwash on the wing: procedures are described to accomplish this for a general wing and flap geometry. The method is applied to several example wings, and the results are compared with experimental data. Theory and test correlate well.

Johnson, W. A.↗
NASA NTRS1987

Comparison of two numerical techniques for aerodynamic model identification

An algorithm, called the Minimal Residual QR algorithm, is presented to solve subset regression problems. It is shown that this scheme can be used as a numerically reliable implementation of the stepwise regression technique, which is widely used to identify an aerodynamic model from flight test data. This capability as well as the numerical superiority of this scheme over the stepwise regression technique is demonstrated in an experimental simulation study.

Verhaegen, M. H.↗
NASA NTRS1987

Comparison of two numerical techniques for aerodynamic model identification

A new algorithm, called the Minimal Residual QR algorithm, is presented to solve subset regression problems. It is shown that this new scheme can be used as a numerically reliable implementation of the stepwise regression technique, which is widely used to identify an aerodynamic model from flight test data. This capability as well as the numerical superiority of this scheme over the stepwise regression technique is demonstrated in an experimental simulation study.

Verhaegen, M. H.↗
NASA NTRS1988

Evaluation of the constant pressure panel method (CPM) for unsteady air loads prediction

This paper evaluates the capability of the constant pressure panel method (CPM) code to predict unsteady aerodynamic pressures, lift and moment distributions, and generalized forces for general wing-body configurations in supersonic flow. Stability derivatives are computed and correlated for the X-29 and an Oblique Wing Research Aircraft, and a flutter analysis is carried out for a wing wind tunnel test example. Most results are shown to correlate well with test or published data. Although the emphasis of this paper is on evaluation, an improvement in the CPM code's handling of intersecting lifting surfaces is briefly discussed. An attractive feature of the CPM code is that it shares the basic data requirements and computational arrangements of the doublet lattice method. A unified code to predict unsteady subsonic or supersonic airloads is therefore possible.

Appa, Kari↗
NASA NTRS1989

SRB ascent aerodynamic heating design criteria reduction study, volume 1

An independent set of solid rocket booster (SRB) convective ascent design environments were produced which would serve as a check on the Rockwell IVBC-3 environments used to design the ascent phase of flight. In addition, support was provided for lowering the design environments such that Thermal Protection System (TPS), based on conservative estimates, could be removed leading to a reduction in SRB refurbishment time and cost. Ascent convective heating rates and loads were generated at locations in the SRB where lowering the thermal environment would impact the TPS design. The ascent thermal environments are documented along with the wind tunnel/flight test data base used as well as the trajectory and environment generation methodology. Methodology, as well as, environment summaries compared to the 1980 Design and Rockwell IVBC-3 Design Environment are presented in this volume, 1.

Crain, W. K.↗
NASA NTRS1991

Aero/fluids database system

The AFAS Database System was developed to provide the basic structure of a comprehensive database system for the Marshall Space Flight Center (MSFC) Structures and Dynamics Laboratory Aerophysics Division. The system is intended to handle all of the Aerophysics Division Test Facilities as well as data from other sources. The system was written for the DEC VAX family of computers in FORTRAN-77 and utilizes the VMS indexed file system and screen management routines. Various aspects of the system are covered, including a description of the user interface, lists of all code structure elements, descriptions of the file structures, a description of the security system operation, a detailed description of the data retrieval tasks, a description of the session log, and a description of the archival system.

Reardon, John E.↗
NASA NTRS1998

Delta Clipper-Experimental In-Ground Effect on Base-Heating Environment

A quasitransient in-ground effect method is developed to study the effect of vertical landing on a launch vehicle base-heating environment. This computational methodology is based on a three-dimensional, pressure-based, viscous flow, chemically reacting, computational fluid dynamics formulation. Important in-ground base-flow physics such as the fountain-jet formation, plume growth, air entrainment, and plume afterburning are captured with the present methodology. Convective and radiative base-heat fluxes are computed for comparison with those of a flight test. The influence of the laminar Prandtl number on the convective heat flux is included in this study. A radiative direction-dependency test is conducted using both the discrete ordinate and finite volume methods. Treatment of the plume afterburning is found to be very important for accurate prediction of the base-heat fluxes. Convective and radiative base-heat fluxes predicted by the model using a finite rate chemistry option compared reasonably well with flight-test data.

Wang, Ten-See↗
NASA NTRS2003

Low Frequency High Amplitude Temperature Oscillations in Loop Heat Pipe Operation

This paper presents a theory that explains low frequency, high amplitude temperature oscillations in loop heat pipe (LHP) operation. Oscillations of the CC temperature with amplitudes on the order of tens of degrees Kelvin and periods on the order of hours have been observed in some LHPs during ambient testing. There are presently no satisfactory explanations for such a phenomenon in the literature. It is well-known that the operating temperature of an LHP with a single evaporator is governed by the compensation chamber (CC) temperature, which in turn is a function of the evaporator heat load, sink temperature, and ambient temperature. As the operating condition changes, the CC temperature will change during the transient but eventually reach a new steady temperature. Under certain conditions, however, the LHP never really reaches a true steady state, but instead displays an oscillatory behavior. The proposed new theory describes why low frequency, high amplitude oscillations may occur when the LHP has a low evaporator power, a low heat sink temperature (below ambient temperature), and a large thermal mass attached to the evaporator. When this condition prevails, there are some complex interactions between the CC, condenser, thermal mass and ambient. The temperature oscillation is a result of the large movement of the vapor front inside the condenser, which is caused by a change in the net evaporator power modulated by the large thermal mass through its interaction with the sink and CC. The theory agrees very well with previously published test data. Effects of various parameters on the amplitude and frequency of the temperature oscillation are also discussed.

Ku, Jentung↗
NASA NTRS2006

Extended Operation of Stirling Convertors in a Thermal Vacuum Environment

A 110 watt Stirling Radioisotope Generator (SRG110) is being developed for potential use on future NASA exploration missions. The development effort is being performed by Lockheed Martin under contract to the Department of Energy (DOE). Infinia, Corp. supplies the free-piston Stirling power convertors, and NASA Glenn Research Center (GRC) provides support to the effort in a range of technologies. This generator features higher efficiency and specific power compared to alternatives. One potential application for the generator would entail significant cruise time in the vacuum of deep space. A test has been initiated at GRC to demonstrate functionality of the Stirling convertors in a thermal vacuum environment. The test article resembles the configuration of the SRG110, however the requirement for low mass was not considered. This test demonstrates the operation of the Stirling convertors in the thermal vacuum environment, simulating deep space, over an extended period of operation. The status of the test as well as the data gathered will be presented in this paper.

Oriti, Salvatore M.↗