Search NASA⌕ Search

SEARCH · Search NASA

Results for “Window Materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Further Analysis of MISSE Polymeric Materials at MSFC

Many different spacecraft materials were flown as part of the Materials on International Space Station Experiment (MISSE). MISSE was exposed to the low Earth orbital environment of atomic oxygen, ultraviolet radiation, thermal cycling, and hard vacuum. A number of polymer samples did not survive the atomic oxygen attack. Mass and thickness loss measurements indicate the durability of the remaining polymeric materials to withstand the space environment. Results from the one-year exposure on MISSE-3 and MISSE-4 are compared to those from the four-year exposure on MISSE-1 and MISSE-2. Solar absorptance and infrared emittance measurements are given for thermal control materials. Transmission measurements are given where appropriate. A wide variety of polymeric materials were flown on MISSE, ranging from extremely thin films for solar sails to bulk materials. Some of the candidate solar sail materials were flown underneath magnesium fluoride windows to eliminate atomic oxygen effects and allow the study of ultraviolet radiation damage. Exposed seal materials include Viton , silicone, and fluorosilicone. Multi-layer insulation materials were flown, including atomic oxygen-resistant polymers. Also flown were candidate inflatable materials for a High Altitude Airship or inflatable lunar habitat. Polymer materials being flown on MISSE-6 are discussed.

Finckenor, Miria M.↗
NASA NTRS1980

Nonmetallic materials contamination studies

In order to impose adequate contamination control requirements in the selection of Wide Field Planetary Camera (WFPC) materials and to develop a data base of potential optical degradation of the WFPC charge-couple device window, the outgassing properties of WFPC materials and the collected volatile condensed material (CVCM) effects on MgF2 transmittance were measured. Changes in the transmittance were monitored in the wavelength region from 115 nm to 300 nm for selected CVCM thicknesses up to 150 nm. The outgassing properties of reemitted CVCM were also studied.

Muscari, J. A.↗
NASA NTRS2011

Optical Property Requirements for Glasses, Ceramics and Plastics in Spacecraft Window Systems

This is a preliminary draft of a standard published by the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) that is intended to provide uniform window optical design requirements in support of the development of human-rated spaceflight hardware. The material covered in this standard is based on data from extensive testing by the Advanced Sensing and Optical Measurement Branch at NASA Langley Research Center, and compiled into requirements format by the NASA JSC Structural Engineering Division. At the time of this initial document release, a broader technical community has not reviewed this standard. The technical content of this standard is primarily based on the Constellation Program Orion Crew Exploration Vehicle Window Optical Properties Requirements, CxP 72407, Baseline. Unlike other optical requirements documents available for human rated spacecraft, this document includes requirements that ensure functionality for windows that contain glass/ceramic and/or plastic window substrate materials. These requirements were derived by measuring the optical properties of fused silica and aluminosilicate glass window assemblies and ensuring that the performance of any window assembly that includes a plastic pane or panes will meet the performance level of the all-glass assemblies. The resulting requirements are based upon the performance and parameter metrology testing of a variety of materials, including glass, transparent ceramics, acrylics, and polycarbonates. In general, these requirements are minimum specifications for each optical parameter in order to achieve the function specified for each functional category, A through D. Because acrylic materials perform at a higher level than polycarbonates in the optics regime, and CxP/Orion is planning to use acrylic in the Orion spacecraft, these requirements are based heavily on metrology from that material. As a result, two of the current Category D requirements for plastics are cited in such a way that will result in the screening out of polycarbonates. It is acknowledged that many polycarbonates can perform the functions of Category D, such as piloting and imagery with lens with apertures up to 25mm, without performance issues. Therefore, this forward warns users that certain requirements, such as birefringence and wavefront, for Category D plastics need to be revised to allow those polycarbonates that perform adequately in Category D to be accepted, while at the same time, screen out those materials that do not perform up to par. At the time of document release, the requirements in question have been identified by a TBD beside the proposed requirement criteria (which is based upon acrylic performance). Vehicles that are designed with acrylic materials for windowpanes are encouraged to use the values presented in this document for all requirements, in order to ensure adequate optical performance.

Lynda R Estes↗
NASA NTRS1998

Broadband Infrared Antireflection Structured Silicon Surfaces

Silicon and germanium are materials often used for IR windows and optical elements. However they have a very high index of refraction, in the order of three to four, which causes large reflection losses on each surface. These losses are especially high under large angles of incidence which are often desirable if signals are faint and fast optics are to be used. Solid antireflection coatings are either not available because materials with appropriate index of refraction do not exist, or their use is limited to a small wavelength range and small angles of incidence. We will present the status of our work to calculate, create, and test the performance of graded structures in Si to reduce its surface reflection. The structures are expected to work over the very broad wavelength range of 10 microns to 1000 microns and a wide range of angle of incidence. We have identified several high aspect ratio MEMS process techniques to create the structures and have done 3D electromagnetic modeling, which predicts significant effects. Measurements on different samples have validated our modeling.

Stewart, Kenneth↗
NASA NTRS1999

Broadband Infrared Antireflection Structured Silicon Surfaces

Silicon and germanium are materials often used for IR windows and optical elements. However they have a very high index of refraction, in the order of three to four, which causes large reflection losses on each surface. These losses are especially high under large angles of incidence which are often desirable if signals are faint and fast optics are to be used. Solid antireflection coatings are either not available because materials with appropriate index of refraction do not exist, or their use is limited to a small wavelength range and small angles of incidence. We will present the status of our work to calculate, create, and test the performance of graded structures in Si to reduce its surface reflection. The structures are expected to work over the very broad wavelength range of 10 to 1000 micrometers and a wide range of angle of incidence. We have identified several high aspect ratio MEMS process techniques to Create the structures and have done 3D electromagnetic modeling, which predicts significant effects. Measurements on different samples have validated our modeling.

Stewart, Kenneth↗
DOE OSTI2025

Dynamic Windows Using Reversible Metal Electrodeposition

The objective of the project is to design, fabricate, and optimize Reversible Metal Electrodeposition (RME) windows that simultaneously achieve color-neutral, fast, uniform switching over a wide dynamic range using low-cost, high-throughput materials and processes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Silicon-On-Silicon Carbide Platform for Integrated Photonics

Silicon carbide (SiC)'s nonlinear optical properties and applications to quantum information have recently brought attention to its potential as an integrated photonics platform. However, despite its many excellent material properties, such as large thermal conductivity, wide transparency window, and strong optical nonlinearities, it is generally a difficult material for microfabrication. Here, it is shown that directly bonded silicon-on-silicon carbide can be a high-performing hybrid photonics platform that does not require the need to form SiC membranes or directly pattern in SiC. The optimized bonding method yields defect-free, uniform films with minimal oxide at the silicon–silicon–carbide interface. Ring resonators are patterned into the silicon layer with standard, complimentary metal–oxide–semiconductor (CMOS) compatible (Si) fabrication and measure room-temperature, near-infrared quality factors exceeding 10 5 . The corresponding propagation loss is 5.7 dB cm -1 . The process offers a wafer-scalable pathway to the integration of SiC photonics into CMOS devices.

36 MATERIALS SCIENCE↗
NASA NTRS1998

Technique for Predicting the RF Field Strength Inside an Enclosure

This Memorandum presents a simple analytical technique for predicting the RF electric field strength inside an enclosed volume in which radio frequency radiation occurs. The technique was developed to predict the radio frequency (RF) field strength within a launch vehicle's fairing from payloads launched with their telemetry transmitters radiating and to the impact of the radiation on the vehicle and payload. The RF field strength is shown to be a function of the surface materials and surface areas. The method accounts for RF energy losses within exposed surfaces, through RF windows, and within multiple layers of dielectric materials which may cover the surfaces. This Memorandum includes the rigorous derivation of all equations and presents examples and data to support the validity of the technique.

Hallett, M.↗
NASA NTRS1998

Technique for Predicting the RF Field Strength Inside an Enclosure

This Memorandum presents a simple analytical technique for predicting the RF electric field strength inside an enclosed volume in which radio frequency radiation occurs. The technique was developed to predict the radio frequency (RF) field strength within a launch vehicle's fairing from payloads launched with their telemetry transmitters radiating and to the impact of the radiation on the vehicle and payload. The RF field strength is shown to be a function of the surface materials and surface areas. The method accounts for RF energy losses within exposed surfaces, through RF windows, and within multiple layers of dielectric materials which may cover the surfaces. This Memorandum includes the rigorous derivation of all equations and presents examples and data to support the validity of the technique.

Hallett, M.↗
NASA NTRS2024

Superfluid-Tight Cryogenic Receiver With Continuous Sub-Kelvin Cooling for EXCLAIM

The EXperiment for Cryogenic Large-Aperture Intensity Mapping (EXCLAIM) is a balloon-borne telescope designed to survey star formation over cosmological time scales using intensity mapping in the 420 – 540 GHz frequency range. EXCLAIM uses a fully cryogenic telescope coupled to six on-chip spectrometers featuring kinetic inductance detectors (KIDs) to achieve high sensitivity, allowing for fast integration in dark atmospheric windows. The telescope receiver is cooled to ≈ 1.7 K by immersion in a superfluid helium bath and enclosed in a superfluid-tight shell with a meta-material anti-reflection coated silicon window. In addition to the optics and the spectrometer package, the receiver contains the magnetic shielding, the cryogenic segment of the spectrometer readout, and the sub-Kelvin cooling system. A three-stage continuous adiabatic demagnetization refrigerator (CADR) keeps the detectors at 100 mK while a 4He sorption cooler provides a 900 mK thermal intercept for mechanical suspensions and coaxial cables. We present the design of the EXCLAIM receiver and report on the flight-like testing of major receiver components, including the superfluid-tight receiver window and the sub-Kelvin coolers.

continuous adiabatic demagnetization refrigerator↗
NASA NTRS2013

High-Reliability Waveguide Vacuum/Pressure Window

The NASA Deep Space Network (DSN) uses commercial waveguide windows on the output waveguide of Ka-band (32 GHz) low-noise amplifiers. Mechanical failure of these windows resulted in an unacceptable loss in tracking time. To address this issue, a new Ka-band WR-28 waveguide window has been designed, fabricated, and tested. The window uses a slab of low-loss, low-dielectric constant foam that is bonded into a 1/2-wave-thick waveguide/flange. The foam is a commercially available, rigid, closed-cell polymethacrylimide. It has excellent electrical properties with a dielectric constant of 1.04, and a loss tangent of 0.01. It is relatively strong with a tensile strength of 1 MPa. The material is virtually impermeable to helium. The finished window exhibits a leak rate of less than 3x10(exp -3)cu cm/s with helium. The material is also chemically resistant and can be cleaned with acetone. The window is constructed by fabricating a window body by brazing a short length of WR-28 copper waveguide into a standard rectangular flange, and machining the resulting part to a thickness of 4.6 mm. The foam is machined to a rectangular shape with a dimension of 7.06x3.53 mm. The foam is bonded into the body with a two-part epoxy. After curing, the excess glue and foam are knife-trimmed by hand. The finished window has a loss of less than 0.08 dB (2%) and a return loss of greater than 25 dB at 32 GHz. This meets the requirements for the DSN application. The window is usable for most applications over the entire 26-to-40-GHz waveguide band. The window return loss can be tuned to a required frequency by var y in g the thickness of the window slightly. Most standard waveguide windows use a thin membrane of material bonded into a recess in a waveguide flange, or sandwiched between two flanges with a polymer seal. Designs using the recessed window are prone to mechanical failure over time due to constraints on the dimensions of the recess that allow the bond to fail. Designs using the sandwich method are often permeable to helium, which prohibits the use of helium leak detection. At the time of this reporting, 40 windows have been produced. Twelve are in operation with a combined operating time of over 30,000 hours without a failure.

Britcliffe, Michael J.↗
NASA NTRS2006

MISSE Materials Results for Applications in the Vision for Space Exploration

Marshall Space Flight Center has a role in the development of the Crew Launch Vehicle and Crew Exploration Vehicle, as well as the Robotic Lunar Exploration Program (RLEP-2) and In-Space Propulsion. The success of these programs depends upon understanding the space environment, the requirements imposed on the spacecraft materials, and data gleaned from materials returned from space. Station Experiment (MISSE) were analyzed at the Marshall Space Flight Center. Changes in mass, optical properties, and mechanical integrity for these samples can indicate which materials may be suitable for use on exploration spacecraft, which materials need further testing, and which materials should not be recommended for long term missions. A number of materials for in-space propulsion were flown on MISSE. These include the conductive, insulative, and non-conductive tether materials selected for the ProSEDS mission. Also included were candidate solar sail materials. The solar sail materials were flown underneath a magnesium fluoride window that allowed ultraviolet radiation through to the sample but blocked any atomic oxygen. Over two hundred materials samples from the Materials on International Space

Source record↗
NASA NTRS1984

Fabrication of glass gas cells for the HALOE and MAPS satellite experiments

The Halogen Occultation Experiment (HALOE) and the Measurement of Air Pollution from Satellites (MAPS) experiment are satellite-borne experiments which measure trace constituents in the Earth's atmosphere. The instruments which obtain the data for these experiments are based on the gas filter correlation radiometer measurement technique. In this technique, small samples of the gases of interest are encapsulated in glass cylinders, called gas cells, which act as very selective optical filters. This report describes the techniques employed in the fabrication of the gas cells for the HALOE and MAPS instruments. Details of the method used to fuse the sapphire windows (required for IR transmission) to the glass cell bodies are presented along with detailed descriptions of the jigs and fixtures used during the assembly process. The techniques and equipment used for window inspection and for pairing the HALOE windows are discussed. Cell body materials and the steps involved in preparing the cell bodies for the glass-to-sapphire fusion process are given.

Sullivan, E. M.↗
NASA NTRS1992

Application of manufactured products

A wide range of products can be manufactured from the following materials: (1) lunar regolith or basalt; (2) regolith or rock beneficiated to concentrate plagioclase or other minerals; (3) iron, extracted from lunar soil or rocks by various means; (4) naturally occurring or easily obtained materials that have cementitious properties; and (5) byproducts of the above materials. Among the products that can be produced from these materials are the following: beams; plates and sheets; transparent plates (windows); bricks and blocks; pipes and tubes; low-density materials (foams); fiber, wire, and cables; foils and reflective coatings; hermetic seals (coatings); and formed objects. In addition to oxygen, which can be obtained by several processes, either from unbeneficiated regolith or by reduction of concentrated ilmenite, these materials make the simplest requirements of the lunar resource extraction system. A thorough analysis of the impact of these simplest products on the economics of space operations is not possible at this point. Research is necessary both to define optimum techniques and adapt them to space and to determine the probable market for the products so that the priority of various processes can be assessed. Discussions of the following products are presented: aerobraking heat shields; pressurized habitats; lunar photovoltaic farms; and agricultural systems.

Sastri, Sankar↗
NASA NTRS2007

Structural Design of Glass and Ceramic Components for Space System Safety

Manned space flight programs will always have windows as part of the structural shell of the crew compartment. Astronauts and cosmonauts need to and enjoy looking out of the spacecraft windows at Earth, at approaching vehicles, at scientific objectives and at the stars. With few exceptions spacecraft windows have been made of glass, and the lessons learned over forty years of manned space flight have resulted in a well-defined approach for using this brittle, unforgiving material in NASA's vehicles, in windows and other structural applications. This chapter will outline the best practices that have developed at NASA for designing, verifying and accepting glass (and ceramic) windows and other components for safe and reliable use in any space system.

Bernstein, Karen S.↗
NASA NTRS2012

Seasonally Active Slipface Avalanches in the North Polar Sand Sea of Mars: Evidence for a Wind-Related Origin

Meter-scale MRO/HiRISE camera images of dune slipfaces in the north polar sand sea of Mars reveal the presence of deep alcoves above depositional fans. These features are apparently active under current climatic conditions, because they form between observations taken in subsequent Mars years. Recently, other workers have hypothesized that the alcoves form due to destabilization and mass-wasting during sublimation of CO2 frost in the spring. While there is evidence for springtime modification of these features, our analysis of early springtime images reveals that over 80% of the new alcoves are visible underneath the CO2 frost. Thus, we present an alternative hypothesis that formation of new alcoves and fans occurs prior to CO2 deposition. We propose that fans and alcoves form primarily by aeolian processes in the mid- to late summer, through a sequence of aeolian deposition on the slipface, over-steepening, failure, and dry granular flow. An aeolian origin is supported by the orientations of the alcoves, which are consistent with recent wind directions. Furthermore, morphologically similar but much smaller alcoves form on terrestrial dune slipfaces, and the size differences between the terrestrial and Martian features may reflect cohesion in the near-subsurface of the Martian features. The size and preservation of the largest alcoves on the Martian slipfaces also support the presence of an indurated surface layer; thus, new alcoves might be sites of early spring CO2 sublimation and secondary mass-wasting because they act as a window to looser, less indurated materials that warm up more quickly in the spring.

Horgan, Briony H. N.↗
NASA NTRS2020

Carbon isotope evidence for the substrates and mechanisms of prebiotic synthesis in the early solar system

Meteorites contain prebiotic, bio-relevant organic compounds including amino acids. Their syntheses could result from diverse sources and mechanisms and provide a window on the conditions and materials present in the early solar system. Here we constrain alanine’s synthetic history in the Murchison meteorite using site-specific 13C/12C measurements, reported relative to the VPDB standard. The δ13CVPDB values of −29 ± 10‰, 142 ± 20‰, and −36 ± 20‰ for the carboxyl, amine-bound, and methyl carbons, respectively, are consistent with Strecker synthesis of interstellar-medium-derived aldehydes, ammonia, and low-δ13C nebular or interstellar-medium-derived CN. We report experimentally measured isotope effects associated with Strecker synthesis, and use them to constrain the δ13C values of the alanine precursors, which we then use to construct a model that predicts the molecular-average δ13C values of 19 other organic compounds of prebiotic significance found in Murchison if they were made by our proposed synthetic network. Most of these predictions agree with previous measurements, suggesting that interstellar-medium-derived aldehydes and nebular and/or pre-solar CN could have served as substrates for synthesis of a wide range of prebiotic compounds in the early solar system.

L.Chimiak↗
NASA NTRS1997

"TPSX: Thermal Protection System Expert and Material Property Database"

The Thermal Protection Branch at NASA Ames Research Center has developed a computer program for storing, organizing, and accessing information about thermal protection materials. The program, called Thermal Protection Systems Expert and Material Property Database, or TPSX, is available for the Microsoft Windows operating system. An "on-line" version is also accessible on the World Wide Web. TPSX is designed to be a high-quality source for TPS material properties presented in a convenient, easily accessible form for use by engineers and researchers in the field of high-speed vehicle design. Data can be displayed and printed in several formats. An information window displays a brief description of the material with properties at standard pressure and temperature. A spread sheet window displays complete, detailed property information. Properties which are a function of temperature and/or pressure can be displayed as graphs. In any display the data can be converted from English to SI units with the click of a button. Two material databases included with TPSX are: 1) materials used and/or developed by the Thermal Protection Branch at NASA Ames Research Center, and 2) a database compiled by NASA Johnson Space Center 9JSC). The Ames database contains over 60 advanced TPS materials including flexible blankets, rigid ceramic tiles, and ultra-high temperature ceramics. The JSC database contains over 130 insulative and structural materials. The Ames database is periodically updated and expanded as required to include newly developed materials and material property refinements.

Squire, Thomas H.↗