Search NASA⌕ Search

SEARCH · Search NASA

Results for “aeroacoustics testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Calculation of the Aerodynamic Behavior of the Tilt Rotor Aeroacoustic Model (TRAM) in the DNW

Comparisons of measured and calculated aerodynamic behavior of a tiltrotor model are presented. The test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, 1/4-scale V- 22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. The calculations were performed using the rotorcraft comprehensive analysis CAMRAD II. Presented are comparisons of measured and calculated performance and airloads for helicopter mode operation, as well as calculated induced and profile power. An aerodynamic and wake model and calculation procedure that reflects the unique geometry and phenomena of tiltrotors has been developed. There are major differences between this model and the corresponding aerodynamic and wake model that has been established for helicopter rotors. In general, good correlation between measured and calculated performance and airloads behavior has been shown. Two aspects of the analysis that clearly need improvement are the stall delay model and the trailed vortex formation model.

Johnson, Wayne↗
NASA NTRS1976

Aeroacoustic studies of coannular nozzles suitable for supersonic cruise aircraft applications

Research programs were conducted to investigate experimentally the aeroacoustic characteristics of scale model, inverted-velocity profile coannular nozzles. These programs include studies of unsuppressed configurations with and without center plugs over a variety of radius ratios and area ratios. Also included are suppressed configurations, the effect of ejectors, and some simulated flight effects. Unsuppressed inverted-velocity profile coannular nozzles seem to allow jet mixing noise compliance with present FAR-36 regulations when applied to supersonic cruise aircraft engine cycles. Simulated flight tests suggest that the aeroacoustic benefits of the inverted-velocity profile coannular nozzles would be maintained in flight.

Gutierrez, O.↗
NASA NTRS2001

Full-Span Tiltrotor Aeroacoustic Model (TRAM) Overview and 40- by 80-Foot Wind Tunnel Test

Most helicopter data trends cannot be extrapolated to tiltrotors because blade geometry and aerodynamic behavior, as well as rotor and fuselage interactions, are significantly different for tiltrotors. A tiltrotor model has been developed to investigate the aeromechanics of tiltrotors, to develop a comprehensive database for validating tiltrotor analyses, and to provide a research platform for supporting future tiltrotor designs. The Full-Span Tiltrotor Aeroacoustic Model (FS TRAM) is a dual-rotor, powered aircraft model with extensive instrumentation for measurement of structural and aerodynamic loads. This paper will present the Full-Span TRAM test capabilities and the first set of data obtained during a 40- by 80-Foot Wind Tunnel test conducted in late 2000 at NASA Ames Research Center. The Full-Span TRAM is a quarter-scale representation of the V-22 Osprey aircraft, and a heavily instrumented NASA and U.S. Army wind tunnel test stand. Rotor structural loads are monitored and recorded for safety-of-flight and for information on blade loads and dynamics. Left and right rotor balance and fuselage balance loads are monitored for safety-of-flight and for measurement of vehicle and rotor aerodynamic performance. Static pressure taps on the left wing are used to determine rotor/wing interactional effects and rotor blade dynamic pressures measure blade airloads. All of these measurement capabilities make the FS TRAM test stand a unique and valuable asset for validation of computational codes and to aid in future tiltrotor designs. The Full-Span TRAM was tested in the NASA Ames Research Center 40- by 80-Foot Wind Tunnel from October through December 2000. Rotor and vehicle performance measurements were acquired in addition to wing pressures, rotor acoustics, and Laser Light Sheet (LLS) flow visualization data. Hover, forward flight, and airframe (rotors off) aerodynamic runs were performed. Helicopter-mode data were acquired during angle of attack and thrust sweeps for a variety of tunnel speeds. Wake geometry images were acquired using LLS photographs and suggest dual tip vortex formation at low thrust conditions. The full paper will include comparisons to isolated-rotor TRAM data acquired at the Duits-Nederlandse Windtunnel (DNW) in 1998. The FS TRAM has been established as a valuable national asset for tiltrotor research. Data reduction and analysis of the 40- by 80-Foot Wind Tunnel test results are underway. Follow-on testing of the FS TRAM is currently being planned for the NASA Ames 80- by 120-Foot Wind Tunnel in late 2001.

McCluer, Megan S.↗
NASA NTRS1976

Aeroacoustics: Acoustic wave propagation; Aircraft noise prediction; Aeroacoustic instrumentation

The papers in this volume deal with recent research into acoustic-wave propagation through the atmosphere and progress in aeroacoustic instrumentation, facilities, and test techniques. Topics include the propagation of aircraft noise over long distances in the lower atmosphere, measured effects of turbulence on the rise time of a weak shock, sound scattering from atmospheric turbulence, saturation effects associated with sound propagation in a turbulent medium, and a computer model of the lightning-thunder process. Other papers discuss the development of a computer system for aircraft noise prediction; aircraft flyover noise measurements; and theories and methods for the prediction of ground effects on aircraft noise propagation, for the prediction of airframe aerodynamic noise, for turbine noise prediction, and for combustion noise prediction. Attention is also given to the use of Hartmann generators as sources of high-intensity sound in a large absorption flow-duct facility, an outdoor jet noise facility, factors in the design and performance of free-jet acoustic wind tunnels, and the use of a laser shadowgraph for jet noise diagnosis.

Schwartz, I. R.↗
NASA NTRS2004

Results From a Parametric Acoustic Liner Experiment Using P and W GEN1 HSR Mixer/Ejector Model

This report documents the results of an acoustic liner test performed using a Gen 1 HSR mixer/ejector model installed on the Jet Exit Rig in the Nozzle Acoustic Test Rig in the Aeroacoustic Propulsion Laboratory or NASA Glenn Research Center. Acoustic liner effectiveness and single-component thrust performance results are discussed. Results from 26 different types of single-degree-of-freedom and bulk material liners are compared with each other and against a hardwall baseline. Design parameters involving all aspects of the facesheet, the backing cavity, and the type of bulk material were varied in order to study the effects of these design features on the acoustic impedance, acoustic effectiveness and on nozzle thrust performance. Overall, the bulk absorber liners are more effective at reducing the jet noise than the single-degree-of-freedom liners. Many of the design parameters had little effect on acoustic effectiveness, such as facesheeet hole diameter and honeycomb cell size. A relatively large variation in the impedance of the bulk absorber in a bulk liner is required to have a significant impact on the noise reduction. The thrust results exhibit a number of consistent trends, supporting the validity of this new addition to the facility. In general, the thrust results indicate that thrust performance benefits from increased facesheet thickness and decreased facesheet porosity.

Boyd, Kathleen C.↗
NASA NTRS2010

Effects of Flow Profile on Educed Acoustic Liner Impedance

This paper presents results of an investigation of the effects of shear flow profile on impedance eduction processes employed at NASA Langley. Uniform and 1-D shear-flow propagation models are used to educe the acoustic impedance of three test liners based on aeroacoustic data acquired in the Langley Grazing Flow Impedance Tube, at source levels of 130, 140 and 150 dB, and at centerline Mach numbers of 0.0, 0.3 and 0.5. A ceramic tubular, calibration liner is used to evaluate the propagation models, as this liner is expected to be insensitive to SPL, grazing flow Mach number, and flow profile effects. The propagation models are then used to investigate the effects of shear flow profile on acoustic impedances educed for two conventional perforate-over-honeycomb liners. Results achieved with the uniform-flow models follow expected trends, but those educed with the 1-D shear-flow model do not, even for the calibration liner. However, when the flow profile used with the shear-flow model is varied to increase the Mach number gradient near the wall, results computed with the shear-flow model are well matched to those achieved with the uniform-flow model. This indicates the effects of flow profile on educed acoustic liner impedance are small, but more detailed investigations of the flow field throughout the duct are needed to better understand these effects.

Jones, Michael G.↗
NASA NTRS2019

Aeroacoustic Measurements of the Bell 699 Rotor on the Tiltrotor Test Rig in the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel

The Tiltrotor Test Rig (TTR) with the Bell 699 Rotor was tested in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel from 2017 to 2018. The primary goal of the test was to understand the operational capabilities of the TTR while also acquiring research data, including acoustic data. A data quality study revealed that the NFAC 40- by 80-Foot Wind Tunnel is an adequate acoustic environment to test the Bell 699 Rotor for helicopter, conversion, and airplane configurations. Representative acoustic data are presented, and selected acoustic data and corresponding test conditions are included.

Schatzman, N. L.↗
NASA NTRS2021

Unsteady Propagation and Mean Corrections in Open-Jet and Kevlar® Wind Tunnels

Two types of aeroacoustic wind-tunnel test section configurations have been tested in the NASA Langley Quiet Flow Facility. The first is a more traditional open-jet configuration, where test section flow passes unbounded through the facility anechoic chamber. The second is a Kevlar® panel configuration, where a tensioned Kevlar sheet constrains the test section flow from the facility anechoic chamber. For both configurations, acoustic instrumentation is in the surrounding quiescent space. Both configurations are evaluated with a laser-based pulsed acoustic source, which provides unique capability for assessing the facility unsteady acoustic propagation characteristics. Metrics based on the wander and spread of the pulses are evaluated, and show that measurements using Kevlar walls experience dramatically reduced unsteady effects when compared to the open-jet configuration. This leads to a corresponding improvement in coherence between microphones with the Kevlar configuration, by reducing the variation in magnitude and phase differences between channels. Magnitude corrections for propagation through Kevlar as compared to open-jet propagation are calculated. Although limitations in the experimental setup make quantitative analysis difficult, qualitative analysis shows Kevlar magnitude corrections similar to those determined in previous literature. Directivity effects beyond those already present for open-jet configurations are minimal. When compared with the open-jet configuration, the background noise produced by the Kevlar is found to be its one drawback, showing significantly greater levels at high frequencies.

wind tunnel testing, hybrid acoustic tunnel, facil↗
NASA NTRSDate not supplied

Aeroacoustic Study of a Subscale Large Civil Transport (STAR) Model – Part 2: Validation of Simulated Results

Aeroacoustic measurements of the 26%-scale, semispan Boeing 777-200 Subsonic Transport Aeroacoustic Research (STAR) model tested in the NASA Ames Research Center 40- by 80-foot wind tunnel were used to ascertain the efficacy of high-fidelity simulations to accurately predict noise from the landing gear of large commercial transports. The simulations, conducted with the lattice Boltzmann solver PowerFLOW®, used a digital replica of the STAR model with or without main landing gear deployed and slats and flaps set to their highest deflection angles to represent aircraft during landing. The computations were performed at a Mach number of 0.21, Reynolds number of 8.2 million based on the model mean aerodynamic chord, and other conditions prevalent during the STAR model test. Measured and computed surface pressures were in very good agreement at most port locations on the model, as were global force coefficients, indicating that the simulations captured the impact of main gear deployment on inboard flap loading. Noise sources produced by the main landing gear and high-lift devices were determined via source localization maps generated with CLEAN from synthetic and experimental data. In general, very good agreement between predicted and measured acoustic source location and relative strength was observed in the maps. Comparisons of far-field noise spectra obtained from the CLEAN deconvolution maps showed remarkable agreement between synthetic and experimental broadband noise at low and medium frequencies. Main landing gear sources for model-scale frequencies above 7,000 Hz could not be resolved with the spatial resolution used during the simulations.

airframe noise↗
NASA NTRS2024

Wind Tunnel Test of A Scale Model of A Venus Probe to Determine Aeroacoustics Environment

The Zephyr probe for NASA’s DAVINCI project is being designed to fly to Venus and collect measurements to characterize the Venusian atmosphere while it descends towards the surface. Despite a slow descent speed as the probe approaches the surface, the very dense atmosphere means the vibro-acoustic environment that the probe must withstand could be very harsh. A wind tunnel test campaign was conducted to characterize the surface-pressure fluctuations (acoustics) on the external surface of the probe during the descent. The goal was to provide forcing functions for vibro-acoustic analysis of all instruments inside the probe. A 25% scale-model of the Zephyr probe was manufactured, instrumented with 18 microphones, and tested in two wind tunnels located in the Fluid Mechanics Lab at NASA Ames Research Center at velocities ranging from 13 m/s to 48 m/s. Trip strips were added to the model to ensure a turbulent boundary layer on the model. Microphones were located appropriately to provide spectra of pressure fluctuations in regions with different flow characteristics as well as for calculating various two-point statistics. The acoustic spectra measured in the wind tunnel tests were scaled up to flight-scale using the estimated flight trajectory information. Besides fluctuating surface-pressure measurements, hot-film velocity measurements as well as smoke-laser flow visualization were conducted to better understand the flow around the probe. Lastly, several different geometry configurations were tested to see whether any reduction in acoustic levels could be achieved, but none of the configurations that were tested offered significant improvements. The flow visualization showed 3 primary flow regimes on the model: an attached turbulent boundary layer on the front of the model, a region of separated flow upstream of the flared lip, and a large, separated wake at the rear of the model. The acoustic spectra generally show three different shapes corresponding to these flow regions, with the highest levels seen at the rear of the model, and directly in front of the drag plate. The scaled overall levels of pressure fluctuations were found to be high: in the range of 130dB to 155dB.

planetary probe↗
NASA NTRS2016

NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration

NASAs Environmentally Responsible Aviation (ERA) Project explores enabling technologies to reduce aviations impact on the environment. One research challenge area for the project has been to study advanced airframe and engine integration concepts to reduce community noise and fuel burn. In order to achieve this, complex wind tunnel experiments at both the NASA Langley Research Centers (LaRC) 14x22 and the Ames Research Centers 40x80 low-speed wind tunnel facilities were conducted on a Boeing Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion airframe interference effects including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on the vehicles aerodynamics. This paper will provide a high level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as some simulation guideline development based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.

Computational Fluid Dynamics↗
NASA NTRS1986

A comparison of the acoustic and aerodynamic measurements of a model rotor tested in two anechoic wind tunnels

Two aeroacoustic facilities--the CEPRA 19 in France and the DNW in the Netherlands--are compared. The two facilities have unique acoustic characteristics that make them appropriate for acoustic testing of model-scale helicopter rotors. An identical pressure-instrumented model-scale rotor was tested in each facility and acoustic test results are compared with full-scale-rotor test results. Blade surface pressures measured in both tunnels were used to correlated nominal rotor operating conditions in each tunnel, and also used to assess the steadiness of the rotor in each tunnel's flow. In-the-flow rotor acoustic signatures at moderate forward speeds (35-50 m/sec) are presented for each facility and discussed in relation to the differences in tunnel geometries and aeroacoustic characteristics. Both reports are presented in appendices to this paper. ;.);

Boxwell, D. A.↗
NASA NTRS1986

A comparison of the acoustic and aerodynamic measurements of a model rotor tested in two anechoic wind tunnels

Two aeroacoustic facilities - the CEPRA 19 in France and the DNW in the Netherlands - are compared. The two facilities have unique acoustic characteristics that make them appropriate for acoustic testing of model-scale helicopter rotors. An identical pressure-instrumented model-scale rotor was tested in each facility and acoustic test results are compared with full-scale-rotor test results. Blade surface pressures measured in both tunnels were used to correlated nominal rotor operating conditions in each tunnel, and also used to assess the steadiness of the rotor in each tunnel's flow. In-the-flow rotor acoustic signatures at moderate forward speeds (35-50 m/sec) are presented for each facility and discussed in relation to the differences in tunnel geometries and aeroacoustic characteristics. Both reports are presented in appendices to this paper.

Boxwell, D. A.↗
NASA NTRS1992

HSCT nozzle source noise programs at Pratt and Whitney

The topics covered include the following: 20 dB jet noise suppression; ejector nozzle technology program - noise reduction vs. flow augmentation; mixer ejector nozzle technology challenges; 1989 High Speed Civil Transport (HSCT) 2-D ejector model test in NASA's 9 x 15 ft. tunnel; tertiary airflow 1989 2-D ejector test; shock noise dominates 2-D ejector test; lessons learned - 2-D mixer/ejector in 9 x 15 ft. tunnel; 1990 HSCT axisymmetric ejector model test in Boeing's Low Speed Aeroacoustic Facility (LSAF); axisymmetric mixer/ejector mach contours - peak and valley - NASTAR pre-test predictions; tertiary airflow objectives accomplished - 1990 AXI model; and HSCT low noise exhaust technology programs.

Stern, Alfred M.↗
NASA NTRS2019

Wind Tunnel Flow Field Visualizations of the Space Launch System Vehicle Ascent

A wind tunnel test was conducted to characterize the aeroacoustic environment of several configurations of the Space Launch System during ascent. The test was conducted in the 11-by-11 foot transonic and 9-by-7 foot supersonic test sections at NASA Ames research center. Throughout this experiment data was collected from several types of instrumentation including: dynamic and steady-state pressure sensors, unsteady and steady pressure sensitive paint, time-resolved shadowgraph and infrared imaging. The following details results and analysis from the time-resolved shadowgraph and infrared imaging data systems. The time-resolved shadowgraph provided a qualitative measurement of the near-field turbulent fluctuations. These results helped provide context to the relative magnitude and frequency content of the fluid-structure-interaction driving the surface pressure phenomena characterized by the discrete pressure transducers and unsteady pressure sensitive paint. The infrared imaging was used to verify boundary layer trip effectiveness and provide temperature correction for the unsteady pressure sensitive paint.

Shadowgraph↗
NASA NTRS2016

NASA ERA Integrated CFD for Wind Tunnel Testing of Hybrid Wing-Body Configuration

The NASA Environmentally Responsible Aviation (ERA) Project explored enabling technologies to reduce impact of aviation on the environment. One project research challenge area was the study of advanced airframe and engine integration concepts to reduce community noise and fuel burn. To address this challenge, complex wind tunnel experiments at both the NASA Langley Research Center's (LaRC) 14'x22' and the Ames Research Center's 40'x80' low-speed wind tunnel facilities were conducted on a BOEING Hybrid Wing Body (HWB) configuration. These wind tunnel tests entailed various entries to evaluate the propulsion-airframe interference effects, including aerodynamic performance and aeroacoustics. In order to assist these tests in producing high quality data with minimal hardware interference, extensive Computational Fluid Dynamic (CFD) simulations were performed for everything from sting design and placement for both the wing body and powered ejector nacelle systems to the placement of aeroacoustic arrays to minimize its impact on vehicle aerodynamics. This paper presents a high-level summary of the CFD simulations that NASA performed in support of the model integration hardware design as well as the development of some CFD simulation guidelines based on post-test aerodynamic data. In addition, the paper includes details on how multiple CFD codes (OVERFLOW, STAR-CCM+, USM3D, and FUN3D) were efficiently used to provide timely insight into the wind tunnel experimental setup and execution.

Computational Fluid Dynamics↗
NASA NTRS2013

Open Rotor Aeroacoustic Installation Effects for Conventional and Unconventional Airframes

As extensive experimental campaign was performed to study the aeroacoustic installation effects of an open rotor with respect to both a conventional tube and wing type airframe and an unconventional hybrid wing body airframe. The open rotor rig had two counter rotating rows of blades each with eight blades of a design originally flight tested in the 1980s. The aeroacoustic installation effects measured in an aeroacoustic wind tunnel included those from flow effects due to inflow distortion or wake interaction and acoustic propagation effects such as shielding and reflection. The objective of the test campaign was to quantify the installation effects for a wide range of parameters and configurations derived from the two airframe types. For the conventional airframe, the open rotor was positioned in increments in front of and then over the main wing and then in positions representative of tail mounted aircraft with a conventional tail, a T-tail and a U-tail. The interaction of the wake of the open rotor as well as acoustic scattering results in an increase of about 10 dB when the rotor is positioned in front of the main wing. When positioned over the main wing a substantial amount of noise reduction is obtained and this is also observed for tail-mounted installations with a large U-tail. For the hybrid wing body airframe, the open rotor was positioned over the airframe along the centerline as well as off-center representing a twin engine location. A primary result was the documentation of the noise reduction from shielding as a function of the location of the open rotor upstream of the trailing edge of the hybrid wing body. The effects from vertical surfaces and elevon deflection were also measured. Acoustic lining was specially designed and inserted flush with the elevon and airframe surface, the result was an additional reduction in open rotor noise propagating to the far field microphones. Even with the older blade design used, the experiment provided quantification of the aeroacoustic installation effects for a wide range of open rotor and airframe configurations and can be used with data processing methods to evaluate the aeroacoustic installation effects for open rotors with modern blade designs.

Czech, Michael J.↗
NASA NTRS1975

Aeroacoustic performance of scale model sonic inlets

Various means can be used to vary engine inlet throat areas in order to reduce noise generated at takeoff and approach. Low-speed wind-tunnel tests were performed to evaluate the aeroacoustic performance of two takeoff geometries (cylindrical centerbody and bulb-shaped centerbody) and four approach geometries (bulb-shaped centerbody, annular ring, radial vanes, and step diffuser). The effects of inlet internal lip shape and diffuser length on sonic inlet performance were also investigated. It was found that the single-passage geometries, in particular a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry, provide the highest level of aeroacoustic performance. Increasing the inlet lip contraction ratio extends the maximum incidence angle for attached lip flow, while increasing the inlet diffuser length increases total pressure recovery for a given amount of noise suppression.

Abbott, J. M.↗