Results for “angle” — Page 8

NASA NTRS1957

Aerodynamic Loads on Tails at High Angles of Attack and Sideslip

Results are presented for the loads and moments acting on the individual tail surfaces of a body-tail combination over a wide range of angles of attack and sideslip. The effects of forebody length and panel-panel interference on the characteristics are included. It is shown that large nonlinear variations in these loads and moments, which occur at some combinations of angle of attack and sideslip, cannot be predicted by low-angle theory. A relatively simple, but general, theoretical method for calculating these load and moment characteristics is described, and the results from this method are found to be in good agreement with experiment provided the initial positions of the forebody vortices are known. It is shown that a simple application of slender-body theory can be used to predict the side loads due to sideslip that are contributed by a vertical tail on a wide variety of wing-body-tail combinations at low angles of attack. For several configurations, changes are indicated which reduced the vertical-tail loads per unit yawing moment of each complete configuration at large angles of attack. Some results are presented on the effect of high angle of attack on the induced-flow field and tail loads due to a wing at supersonic speed.

SLENDER BODY↗

NASA NTRS1974

Estimation of deviation angle for axial-flow compressor blade sections using inviscid-flow solutions

Development of a method of estimating deviation angles by analytical procedures was begun. Solutions for inviscid, irrotational flow in the blade-to-blade plane were obtained with a finite-difference calculation method. Deviation angles for a plane cascade with a rounded trailing edge were estimated by using the inviscid-flow solutions and three trailing-edge hypotheses. The estimated deviation angles were compared with existing experimental data over a range of incidence angles at inlet flow angles of 30 deg and 60 deg. The results indicate that deviation angles can be estimated accurately (within 1 deg) by using one of the three trailing-edge hypotheses, but only when pressure losses are low. A new trailing-edge hypotheses is presented which is suitable (for the cascade considered) for both low- and high-loss operating points.

Miller, M. J.↗

NASA NTRS1975

Laminar separation on a blunted cone at high angles of attack

A new technique is reported for calculating the entire flow field on spherically blunted cones at high angles of attack and high laminar Reynolds numbers. An approximate system of parabolic equations obtained from the steady Navier-Stokes equations by assuming the viscous, streamwise derivative terms are small compared to the viscous normal and circumferential derivatives is the basis of the calculations. These equations are valid for both the inviscid and viscous regions, including the circumferential separation zone that develops on the leeward side at high angles of attack. Two different methods are used to obtain the initial conditions for these equations at the sphere cone tangency plane. For small nose Reynolds numbers, an axisymmetric merged layer solution around a sphere is rotated to provide a three-dimensional initial plane of data. For large nose Reynolds numbers, the nose region is solved using an inviscid, three dimensional time dependent solution combined with a boundary layer solution for the viscous flow. The computed flowfield including the leeward separation region is described and compared with data for a 7 deg half angle cone at 10 deg angle of attack, and a blunt 15 deg half angle cone at 15 deg angle of attack.

Lubard, S. C.↗

NASA NTRS1975

Signature extension for sun angle, volume 1

The author has identified the following significant results. Within a restricted zenith sun angle range of 35 - 50 degrees, it was empirically observed that canopy reflectance is mainly Lambertian. Reflectance changes with crop stage were simple shifts in scale in the sun angle range. It was noted that sun angle variations depend on canopy characteristics. Effects of the vegetative canopy were most pronounced at the larger solar zenith angles (20 %). The linear sun angle correction coefficients demonstrate a dependency on both crop stage (15-20 %) and crop type (10-20 %). The use of canopy reflectance modeling allowed for the generation of a simulated data set over an extremely broad envelope of sun angles.

Smith, J. A.↗

NASA NTRS1976

Heat-transfer distributions on a 0.013-scale shuttle solid rocket booster at Mach 3.70 and angles of attack from 0 deg to 180 deg

An experimental investigation was conducted in the Langley Unitary Plan wind tunnel to estimate the peak aerodynamic heating on the space shuttle solid rocket booster during the descent phase of its flight. Heat transfer measurements were obtained using 0.013 scale models instrumented with thermocouples at a Mach number of 3.70, Reynolds number per meter of 11.48 million, and angles of attack from 0 to 180 deg. At angles of attack of 0 and 180 deg, heat transfer measurements on the cylindrical section of the model between the conical nose and ring interaction region were in good agreement with flat plate strip theory for laminar and turbulent flow. At angles of attack up to 30 deg, measurements on this section of the model were in good agreement with laminar swept-cylinder theory, whereas at angles of attack from 120 to 180 deg, the measurements were in good agreement with turbulent swept-cylinder theory. The good agreement with turbulent theory indicated that large flow disturbances created by the nozzle and afterbody flare at these large angles of attack influenced the downstream heating primarily by promoting boundary layer transition. Measurements obtained at 90 deg angle of attack were indicative of laminar flow.

Lamb, M.↗

NASA NTRS1977

Assessment of existing analytic methods for prediction of high angle-of-attack loads on delta wings at supersonic speeds

An assessment of the applicability of four loading prediction methods to high angle-of-attack conditions for simplified wing-body configurations is provided. The methods are: The tangent wedge approximation, the linear theory methods of Middleton and Woodward, and a shock-fitting finite-difference technique. Estimates obtained by these methods were compared with experimental pressure data on delta wings to examine the effects of Mach number, camber, sweep angle, and angle of attack. Results indicate that all of the methods provided reasonable estimates at moderate angles of attack. At these moderate angles of attack, the methods of Middleton and Woodward provided good estimates at Mach numbers higher than those usually associated with linear theory. Only the finite-difference method provided reasonable load estimates at high angles of attack.

Landrum, E. J.↗

NASA NTRS1978

Pitch angle dispersion of drifting energetic protons at synchronous orbit

The time of arrival at ATS 6 of substorm-associated energetic proton flux enhancements has been examined as a function of both energy and pitch angle by using electron-proton spectrometer data. The protons exhibit energy dispersion with the particles with the highest energy arriving first. This has generally been interpreted as evidence that these particles have gradient- and curvature-drifted to the spacecraft from an acceleration region on the nightside. In the evening quadrant, proton enhancements at 90 deg pitch angle arrived at the spacecraft prior to those at small pitch angles. However, on the dayside the increase occurs first at the smallest pitch angle (about 30 degrees). The difference between the arrival times of the 30 deg and 90 deg protons increases for more westward local times. For the highest energy range observed, drifting protons are rarely seen at large pitch angles. These observations place severe restrictions on the simple drift models. Since the pitch angle dependence of the particle drift velocity is a field geometric quantity, the observations require the modification of present magnetospheric magnetic field models. In particular, the models need to reproduce better the enhanced field observed on the dayside near synchronous orbit.

Walker, R. J.↗

NASA NTRS1979

Modal propagation angles in ducts with soft walls and their connection with suppressor performance

The angles of propagation of the wave fronts associated with duct modes are derived for a cylindrical duct with soft walls (acoustic suppressors) and a uniform steady flow. The angle of propagation with respect to the radial coordinate (angle of incidence on the wall) is shown to be a better correlating parameter for the optimum wall impedance of spinning modes than the previously used mode cutoff ratio. Both the angle of incidence upon the duct wall and the propagation angle with respect to the duct axis are required to describe the attenuation of a propagating mode. Using the modal propagation angles, a geometric acoustics approach to suppressor acoustic performance was developed. Results from this approximate method were compared to exact modal propagation calculations to check the accuracy of the approximate method. The results are favorable except in the immediate vicinity of the modal optimum impedance where the approximate method yields about one-half of the exact maximum attenuation.

Rice, E. J.↗

NASA NTRS1979

Modal propagation angles in ducts with soft walls and their connection with suppressor performance

The angles of propagation of the wave fronts associated with duct modes are derived for a cylindrical duct with soft walls (acoustic suppressors) and a uniform steady flow. The angle of propagation with respect to the radial coordinate (angle of incidence on the wall) is shown to be a better correlating parameter for the optimum wall impedance of spinning modes than the previously used mode cutoff ratio. Both the angle of incidence upon the duct wall and the propagation angle with respect to the duct axis are required to describe the attenuation of a propagating mode. Using the modal propagation angles, a geometric acoustics approach to suppressor acoustic performance was developed. Results from this approximate method were compared to exact modal propagation calculations to check the accuracy of the approximate method. The results are favorable except in the immediate vicinity of the modal optimum impedance where the approximate method yields about one-half of the exact maximum attenuation.

Rice, E. J.↗

NASA NTRS1980

On failure modes in finite width angle ply laminates

The results of a failure analysis of finite width (+ or - theta)s T300/5208 graphite-epoxy laminates subjected to thermal curing loads and applied tensile strain are presented. Stress distributions obtained from linear elastic and linear thermoelastic finite element stress analyses are used in conjunction with the tensor polynomial failure criterion to predict the mode and location of first failure in laminates with fiber angles ranging from five to seventy-five degrees. It is shown that the mode of failure is predominantly interlaminar shear for small fiber angles, shifts to combined interlaminar normal, in-plane shear and in-plane normal for intermediate angles, and is primarily transverse tension for large fiber angles. The location of initial failure shifts from the (+ or - theta)s interface for small fiber angles to the midplane for large fiber angles.

Herakovich, C. T.↗

NASA NTRS1982

Velocity and flow angle measurements in the Langley 0.3-meter transonic cryogenic tunnel using a laser transit anemometer

The Laser Transit Anemometer (LTA) system is described. In the LTA system two parallel laser beams of known separation and cross sectional area are focussed at the same location or plane. When a particle in a flow field passes through both beams and the time is recorded for its transit (time of flight), its velocity can be calculated knowing the distance between the beams. By rotating the two beams (spots) around a common center and recording the number of valid events (a particle which passes through both spots in the proper sequence) at each angle the flow angle can be determined by curve fitting a predetermined number of angles or points and calculating the peak of what should be a Gaussian curve. The best angle or flow angle is defined as the angle at which the maximum number of valid events occurs. The LTA system functioned properly although conditions were less than desirable.

Honaker, W. C.↗

NASA NTRS1990

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, Ramani↗

NASA NTRS1991

Effects of yaw on low angle injection into a supersonic flow

This paper presents the results of a study of transverse gas injection into supersonic/hypersonic streams with low downstream transverse angles in addition to yaw angles varying from zero to approximately 30 deg. The primary data are concentration measurements, with nanoshadowgraphs and oil flow visualization pictures also included. Two sets of experiments were performed. The first set studied the effects of yaw angle, specifically beta = 15 and 28 deg, on a helium injector with a 30-deg transverse angle in a Mach 3 freestream. Axial measurement stations were x/d = 30, 50, and 100. It was found that, as beta was increased, the maximum concentration mixing rate did not vary, but the jet core penetration decreased more at beta = 15 deg than at beta = 28 deg. A shearing effect between the portion of the jet in the boundary layer and the portion in the freestream increased the area of a typical constant concentration contour. The second set of experiments, conducted at NASA Langley, studied the effect of yawed injection at a transverse angle of 15 deg in a Mach 6 flow. Axial stations of x/d = 20, 40, 60, and 80 were used. A yaw angle of beta = 15 deg was found to decrease both the jet core mixing rate and penetration. The primary benefit of yaw was to increase lateral spreading. For similar injection conditions, the results show less near-field mixing at Mach 6 than Mach 3, but a faster mixing rate in the far-field at Mach 6.

Thomas, R. H.↗

NASA NTRS1990

The radiation of sound from a propeller at angle of attack

The mechanism by which the noise generated at the blade passing frequency by a propeller is altered when the propeller axis is at an angle of attack to the freestream is examined. The measured noise field is distinctly non axially symmetric under such conditions with far field sound pressure levels both diminished and increased relative to the axially symmetric values produced with the propeller at zero angle of attack. Attempts have been made to explain this non axially symmetric sound field based on the unsteady (once per rev) loading experienced by the propeller blades when the propeller axis is at non zero angle of attack. A calculation based on this notion appears to greatly underestimate the measured azimuthal asymmetry of noise for high tip speed, highly loaded propellers. A new mechanism is proposed; namely, that at angle of attack, there is a non axially symmetric modulation of the radiative efficiency of the steady loading and thickness noise which is the primary cause of the non axially symmetric sound field at angle of attack for high tip speed, heavily loaded propellers with a large number of blades. A calculation of this effect to first order in the crossflow Mach number (component of freestream Mach number normal to the propeller axis) is carried out and shows much better agreement with measured noise data on the angle of attack effect.

Mani, R.↗

NASA NTRS1991

Pitch angle scattering of cometary ions into monospherical and bispherical distributions

Low frequency magnetic fluctuations generated by solar wind/cometary ion distributions cause pitch-angle scattering of cometary ions. The nature of this pitch angle scattering is examined by means of one-dimensional hybrid simulations, in which newborn ions are created at a constant rate, and for various injection angles, alpha, relative to the magnetic field. Pitch angle scattering in the quasi-perpendicular regime (alpha above 60 deg) results in a bispherical velocity distribution while in the quasi-parallel regime (alpha between 0 and 60 deg), pitch angle scattering can result in either a monospherical or bispherical distribution, depending on the injection angle and initial beam velocity.

Miller, Ronald H.↗

NASA NTRS1992

Factors influencing the effective spray cone angle of pressure-swirl atomizers

The spray cone angles produced by several simplex pressure-swirl nozzles are examined using three liquids whose viscosities range from 0.001 to 0.012 kg/ms (1 to 12 cp). Measurements of both the visible spray cone angle and the effective spray cone angle are carried out over wide ranges of injection pressure and for five different values of the discharge orifice length/diameter ratio. The influence of the number of swirl chamber feed slots on spray cone angle is also examined. The results show that the spray cone angle widens with increase in injection pressure but is reduced by increases in liquid viscosity and/or discharge orifice length/diameter ratio. Variation in the number of swirl chamber feed slots between one and three has little effect on the effective spray cone angle.

Chen, S. K.↗

NASA NTRS1935

The Effect of the Angle of Afterbody Keel on the Water Performance of a Flying-Boat Hull Model

NACA model 11-C was tested according to the general method with the angle of afterbody keel set at five different angles from 2-1/2 degrees to 9 degrees, but without changing other features of the hull. The results of the tests are expressed in curves of test data and of non-dimensional coefficients. At the depth of step used in the tests, 3.3 percent beam, the smaller angles of afterbody keel give greater load-resistance ratios at the hump speed and smaller at high speed than the larger angles of afterbody keel. Comparisons are made of the load-resistance ratios at several other points in the speed range. The effect of variation of the angle of afterbody keel upon the take-off performance of a hypothetical flying boat of 15,000 pounds gross weight having a hull of model 11-C lines is calculated, and the calculations show that the craft with the largest of the angles of afterbody keel tested, 9 degrees, takes off in the least time and distance.

Allison, John M.↗

NASA NTRS1957

Measurement of Aerodynamic Forces for Various Mean Angles of Attack on an Airfoil Oscillating in Pitch and on Two Finite-span Wings Oscillating in Bending with Emphasis on Damping in the Stall

The oscillating air forces on a two-dimensional wing oscillating in pitch about the midchord have been measured at various mean angles of attack and at Mach numbers of 0.35 and 0.7. The magnitudes of normal-force and pitching-moment coefficients were much higher at high angles of attack than at low angles of attack for some conditions. Large regions of negative damping in pitch were found, and it was shown that the effect of increasing the Mach number 0.35 to 0.7 was to decrease the initial angle of attack at which negative damping occurred. Measurements of the aerodynamic damping of a 10-percent-thick and of a 3-percent-thick finite-span wing oscillating in the first bending mode indicate no regions of negative damping for this type of motion over the range of variables covered. The damping measured at high angles of attack was generally larger than that at low angles of attack. (author)

Rainey, A Gerald↗