Search NASA⌕ Search

SEARCH · Search NASA

Results for “automatic gain control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Flight-deck automation - Promises and problems

The paper analyzes the role of human factors in flight-deck automation, identifies problem areas, and suggests design guidelines. Flight-deck automation using microprocessor technology and display systems improves performance and safety while leading to a decrease in size, cost, and power consumption. On the other hand negative factors such as failure of automatic equipment, automation-induced error compounded by crew error, crew error in equipment set-up, failure to heed automatic alarms, and loss of proficiency must also be taken into account. Among the problem areas discussed are automation of control tasks, monitoring of complex systems, psychosocial aspects of automation, and alerting and warning systems. Guidelines are suggested for designing, utilising, and improving control and monitoring systems. Investigation into flight-deck automation systems is important as the knowledge gained can be applied to other systems such as air traffic control and nuclear power generation, but the many problems encountered with automated systems need to be analyzed and overcome in future research.

Wiener, E. L.↗
NASA NTRS1981

Development and evaluation of automatic landing control laws for power lift STOL aircraft

A series of investigations were conducted to generate and verify through ground bases simulation and flight research a data base to aid in the design and certification of advanced propulsive lift short takeoff and landing aircraft. Problems impacting the design of powered lift short haul aircraft that are to be landed automatically on STOL runways in adverse weather were examined. An understanding of the problems was gained by a limited coverage of important elements that are normally included in the certification process of a CAT 3 automatic landing system.

Feinreich, B.↗
NASA NTRS1987

Linear quadratic stationkeeping on travelling ellipses

An automatic controller for Space Shuttle stationkeeping or formationkeeping is presented. The controller, which is a candidate for future on-orbit autopilot enhancement, uses a fuel 'optimized' limit cycle trajectory in a feedforward loop for precise control at nonequilibrium set points. Disturbance rejection is accomplished by a discrete time, linear quadratic regulator, which is employed for tracking of the feedforward model. Feedback gain selection is done to provide good limit cycling performance and low fuel consumption. Velocity correlations are carried out by use of a pseudo 6 degree-of-freedom jet selection scheme. Results indicate that 20 ft precision can be achieved using current sensors.

Adams, Neil J.↗
NASA NTRS1985

The integrated manual and automatic control of complex flight systems

Pilot/vehicle analysis techniques for optimizing aircraft handling qualities are presented. The analysis approach considered is based on the optimal control frequency domain techniques. These techniques stem from an optimal control approach of a Neal-Smith like analysis on aircraft attitude dynamics extended to analyze the flared landing task. Some modifications to the technique are suggested and discussed. An in depth analysis of the effect of the experimental variables, such as prefilter, is conducted to gain further insight into the flared land task for this class of vehicle dynamics.

Schmidt, D. K.↗
NASA NTRS1987

Flight test of a digital controller used in a helicopter autoland system

This paper describes the flight test evaluation of an advanced digital helicopter flight control system. The controller was designed using an optimal control design procedure for a fully coupled lateral and longitudinal vehicle model. Explicit integrals of the guidance error were included to produce a type 1 characteristic. Gain scheduling was used to account for changes in the vehicle dynamics. The digital controller was exercised by combining it with state estimators, a trajectory generator, and a closed-loop guidance algorithm to form a helicopter autoland system. A CH-47 tandem rotor helicopter was equipped with sensors, on-board digital flight computers, and electrohydraulic actuators. The system was exercised by automatically flying straight-in descending decelerating trajectories typcial of VFR manual landing approaches. A description of the test-ground facilities, the flight hardware and software, and the velocity and position tracking performance is included.

Downing, David R.↗
NASA NTRS1986

Redundant control system for X-wing valve actuators

The capability of compensating automatically for a failure in an actuator and the associated drive circuit is enhanced by providing a dual channel actuator, each channel having a drive coil and a position sensor tracking the position of the actuator output shaft. A separate circuit is provided for each actuator channel to detect drive loop failures and hydraulic failures. When the drive loop of one channel fails, it is disengaged, and the gain in the remaining drive loop is doubled to maintain authority. In an embodiment, the remaining drive loop cannot disengage when certain criteria, relating to the failure of associated actuators, are met. The invention is particularly useful for aerospace applications.

Arifian, Kenneth C.↗
NASA NTRS1976

Digital controllers for VTOL aircraft

Using linear-optimal estimation and control techniques, digital-adaptive control laws have been designed for a tandem-rotor helicopter which is equipped for fully automatic flight in terminal area operations. Two distinct discrete-time control laws are designed to interface with velocity-command and attitude-command guidance logic, and each incorporates proportional-integral compensation for non-zero-set-point regulation, as well as reduced-order Kalman filters for sensor blending and noise rejection. Adaptation to flight condition is achieved with a novel gain-scheduling method based on correlation and regression analysis. The linear-optimal design approach is found to be a valuable tool in the development of practical multivariable control laws for vehicles which evidence significant coupling and insufficient natural stability.

Stengel, R. F.↗
NASA NTRS1984

Flight tests of the Digital Integrated Automatic Landing System (DIALS)

The design, development, implementation and flight tests of the Digital Integrated Automatic Landing System (DIALS) are discussed. The system was implemented and flight tested on the Transport Systems Research Vehicle (TSRV), a Boeing 737-100. The design uses modern optimal control methods. The direct digital design obtained uses a 10 Hz rate for the sampling of sensors and the control commands. The basic structure of the control law consists of a steady state Kalman filter followed by a control gain matrix. The sensor information used includes Microwave Landing System (MLS) position, attitude, calibrated airspeed, and body accelerations. The phases of the final approach considered are localized and steep glideslope capture (which may be performed simultaneously or independently), localizer and glideslope track, crab/decrab, and flare to touchdown. The system can capture, track, and flare from conventional, as well as steep, glideslopes ranging from 2.5 deg to 5.5 deg. All of the modes of the control law including the Kalman filters were implemented on the TSRV flight computers which use fixed point arithmetic with 16 bit words. The implementation considerations are described as well as an analysis of the flight test results.

Halyo, N.↗
NASA NTRS1986

Simulation results of automatic restructurable flight control system concepts

The restructurable flight control system (RFCS) described by Weiss et al. (1986) is reviewed, and several results of an extensive six degrees of freedom nonlinear simulation of several aspects of this system are reported. It is concluded that the nontraditional use of standard control surfaces in a nominal feedback control system to spread control authority among many redundant control elements provides a significant amount of fault tolerance without any use of restructuring techniques. The use of new feedback gains alone following a failure can provide significantly improved recovery as long as the control elements remain within their travel limits and as long as uncertainty about the failure identity is properly handled. The use of the feed-forward trim solution in conjunction with redesigned feedback gains allows recovery to take place even when significant control saturation occurs.

Weiss, J. L.↗
NASA NTRS2011

A Control Allocation System for Automatic Detection and Compensation of Phase Shift Due to Actuator Rate Limiting

This paper proposes a control allocation system that can detect and compensate the phase shift between the desired and the actual total control effort due to rate limiting of the actuators. Phase shifting is an important problem in control system applications since it effectively introduces a time delay which may destabilize the closed loop dynamics. A relevant example comes from flight control where aggressive pilot commands, high gain of the flight control system or some anomaly in the system may cause actuator rate limiting and effective time delay introduction. This time delay can instigate Pilot Induced Oscillations (PIO), which is an abnormal coupling between the pilot and the aircraft resulting in unintentional and undesired oscillations. The proposed control allocation system reduces the effective time delay by first detecting the phase shift and then minimizing it using constrained optimization techniques. Flight control simulation results for an unstable aircraft with inertial cross coupling are reported, which demonstrate phase shift minimization and recovery from a PIO event.

Yildiz, Yidiray↗
NASA NTRS1976

Generalization and refinement of an automatic landing system capable of curved trajectories

Refinements in the lateral and longitudinal guidance for an automatic landing system capable of curved trajectories were studied. Wing flaps or drag flaps (speed brakes) were found to provide faster and more precise speed control than autothrottles. In the case of the lateral control it is shown that the use of the integral of the roll error in the roll command over the first 30 to 40 seconds of flight reduces the sensitivity of the lateral guidance to the gain on the azimuth guidance angle error in the roll command. Also, changes to the guidance algorithm are given that permit pi-radian approaches and constrain the airplane to fly in a specified plane defined by the position of the airplane at the start of letdown and the flare point.

Sherman, W. L.↗
NASA NTRS1973

Multi-input, multi-output regulator design for constant disturbances and non-zero set points with application to automatic landing in a crosswind

Undesirable steady offsets result when a stationary, linear regulator using state feedback is subjected to constant disturbances and/or non-zero setspoints. To eliminate these offsets, the disturbances and non-zero setpoints can be fed forward to the control. Only when the number of outputs is less than or equal to the number of control inputs can the outputs be maintained at arbitrary non-zero setpoints. The state and the disturbance may be estimated using a constant gain Kalman filter or by modeling the constant disturbances as exponentially correlated processes with long correlation times.

Holley, W. E.↗
NASA NTRS1979

Flight test of a VTOL digital autoland system along complex trajectories

The objective of this research is the development and flight test of a digital multi-rate VTOL autoland system. This autoland system provided the NASA/Army Fly-by-Wire CH-47 helicopter with an automatic 4-D trajectory following and landing capability. Flight tests were conducted along complex trajectories with descending, turning, and decelerating segments. The flight software consists of a trajectory generator and guidance algorithm operating at two iterations per second and a set of sensor filters and an advanced controller operating at 10 iterations per second. This low iteration rate digital controller has a proportional-integral structure that provides an autotrim function. The control gains, scheduled as a function of flight condition, are updated every two seconds. All flight software, except input/output routines, are coded in FORTRAN using floating point arithmetic and are exercised in a ROLM 1664 flight computer. The flight software, the ground and flight hardware, the autoland system's position tracking performance, and the controller's velocity and heading tracking performance are presented.

Downing, D. R.↗
NASA NTRS1976

An algorithm for automatic reduction of complex signal flow graphs

A computer algorithm is developed that provides efficient means to compute transmittances directly from a signal flow graph or a block diagram. Signal flow graphs are cast as directed graphs described by adjacency matrices. Nonsearch computation, designed for compilers without symbolic capability, is used to identify all arcs that are members of simple cycles for use with Mason's gain formula. The routine does not require the visual acumen of an interpreter to reduce the topology of the graph, and it is particularly useful for analyzing control systems described for computer analyses by means of interactive graphics.

Young, K. R.↗
NASA NTRS2007

Design and Data Management System

The Design and Data Management System (DDMS) was developed to automate the NASA Engineering Order (EO) and Engineering Change Request (ECR) processes at the Propulsion Test Facilities at Stennis Space Center for efficient and effective Configuration Management (CM). Prior to the development of DDMS, the CM system was a manual, paper-based system that required an EO or ECR submitter to walk the changes through the acceptance process to obtain necessary approval signatures. This approval process could take up to two weeks, and was subject to a variety of human errors. The process also requires that the CM office make copies and distribute them to the Configuration Control Board members for review prior to meetings. At any point, there was a potential for an error or loss of the change records, meaning the configuration of record was not accurate. The new Web-based DDMS eliminates unnecessary copies, reduces the time needed to distribute the paperwork, reduces time to gain the necessary signatures, and prevents the variety of errors inherent in the previous manual system. After implementation of the DDMS, all EOs and ECRs can be automatically checked prior to submittal to ensure that the documentation is complete and accurate. Much of the configuration information can be documented in the DDMS through pull-down forms to ensure consistent entries by the engineers and technicians in the field. The software also can electronically route the documents through the signature process to obtain the necessary approvals needed for work authorization. The workflow of the system allows for backups and timestamps that determine the correct routing and completion of all required authorizations in a more timely manner, as well as assuring the quality and accuracy of the configuration documents.

Messer, Elizabeth↗
NASA NTRS1958

Flight Investigation of a Normal-Acceleration Automatic Longitudinal Control System in a Fighter Airplane

A flight investigation was made to obtain experimental information on the handling qualities of a normal-acceleration type of automatic longitudinal control system. The control system was installed in a subsonic fighter-type airplane. In hands-off (stick-free) flight the normal-acceleration control system attempted to regulate the normal acceleration to a constant value which is dependent on the automatic-control-system trim setting. In maneuvering flight a given pilot's stick deflection produced a proportional change in normal acceleration, the change in acceleration being independent of flight condition. A small side-located controller stick was used by the pilot to introduce signals into the automatic control system. In the flight program emphasis was placed on the acceleration-limiting capabilities of the control system. The handling qualities were investigated in maneuvers such as slow and rapid pull-ups and turns and also in flight operations such as cruising, stalls, landings, aerobatics, and air-to-air tracking. Good acceleration limiting was obtained with the normal-acceleration control system by limiting the magnitude of the input signal that the pilot could introduce into the control system. The same values of control-system gain settings could be used from an acceleration-limiting stand-point at both 10,000 and 30,000 feet for the complete speed range of the airplane. The response characteristics of the airplane-control system combination were also satisfactory at both high and low altitude with these same values of control-system gain setting. In the pilot's opinion, the normal-acceleration control system provided good stability and control characteristics in flight operations such as cruising, stalls, landings, aerobatics, and air-to-air tracking.

Sjoberg, S. A.↗
NASA NTRS2004

An aerobot for global in situ exploration of Titan

This paper describes the design and component testing of an aerobot that would be capable of global in situ exploration of Saturn's moon, Titan, over a 6 to 12 month mission lifetime. The proposed aerobot is a propeller-driven, buoyant vehicle that resembles terrestrial airships. However, the extremely cold Titan environment requires the use of cryogenic materials of construction and careful thermal design for protection of temperature-sensitive payload elements. Multiple candidate balloon materials have been identified based on extensive laboratory testing at 77 K. The most promising materials to date are laminates comprised of polyester fabrics and/or films with areal densities in the range of 40-100 g/m2. The aerobot hull is a streamlined ellipsoid 14 meters in length with a maximum diameter of 3 meters. The enclosed volume of 60 m3 is sufficient to float a mass of 234 kg at a maximum altitude of 8 km at Titan. Forward and aft ballonets are located inside the hull to enable the aerobot to descend to the surface while preserving a fully inflated streamlined shape. Altitude changes are effected primarily through thrust vectoring of the twin main propellers, with pressure modulated buoyancy change via the ballonets available as a slower backup option. A total of 100 W of electrical power is provided to the vehicle by a radioisotope power supply. Up to half of this power is available to the propulsion system to generate a top flight speed in the range of 1-2 m/s. This speed is expected to be greater than the near surface winds at Titan, enabling the aerobot to fly to and hover over targets of interest. A preliminary science payload has been devised for the aerobot to give it the capability for aerial imaging of the surface, atmospheric observations and sampling, and surface sample acquisition and analysis. Targeting, hovering, surface sample acquisition and vehicle health monitoring and automatic safing actions will all require significant on-board autonomy due to the over two hour round trip light time between Titan and Earth. An autonomy architecture and a core set of perception, reasoning and control technologies is under development using a free-flying airship testbed of approximately the same size as the proposed Titan aerobot. Data volume from the Titan science mission is expected to be on the order of 100-300 Mbit per day transmitted either direct to Earth through an 0.8 m high gain antenna or via an orbiter relay using an omni-directional antenna on the aerobot.

mobility↗
NASA NTRS1987

Challenges in modeling the X-29 flight test performance

Presented are methods, instrumentation, and difficulties associated with drag measurement of the X-29A aircraft. The initial performance objective of the X-29A program emphasized drag polar shapes rather than absolute drag levels. Priorities during the flight envelope expansion restricted the evaluation of aircraft performance. Changes in aircraft configuration, uncertainties in angle-of-attack calibration, and limitations in instrumentation complicated the analysis. Limited engine instrumentation with uncertainties in overall in-flight thrust accuracy made it difficult to obtain reliable values of coefficient of parasite drag. The aircraft was incapable of tracking the automatic camber control trim schedule for optimum wing flaperon deflection during typical dynamic performance maneuvers; this has also complicated the drag polar shape modeling. The X-29A was far enough off the schedule that the developed trim drag correction procedure has proven inadequate. However, good drag polar shapes have been developed throughout the flight envelope. Preliminary flight results have compared well with wind tunnel predictions. A more comprehensive analysis must be done to complete performance models. The detailed flight performance program with a calibrated engine will benefit from the experience gained during this preliminary performance phase.

John W Hicks↗