SEARCH · Search NASA

Results for “axis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Repetitive Q-switched operation of x-axis Nd:La2Be2O5

The repetitive Q-switched performances of an x-axis neodymium-doped lanthanum beryllate (Nd:BeL) laser and the current state-of-the-art Nd:YAG laser are compared. Output beam pulse energy, peak power, pulse width, beam divergence and mode pattern were measured for a gold-plated single elliptical cavity using a xenon flashlamp for excitation. The output of the Nd:BeL laser is found to exceed that of the Nd:YAG laser by a factor of two at Q-switched repetition rates on the order of 1 Hz, due to the smaller stimulated emission cross section of the x-axis Nd:BeL. When the repetition rate is increased to 10 Hz, the Nd:BeL output falls to a level three fifths lower than its low-rate value, while Nd:YAG output remained essentially constant. Analysis reveals that the decrease in output may be attributed to a depolarization loss due to thermally induced stress birefringence.

Tucker, A. W.↗

NASA NTRS1981

Pressure distributions and shock shapes for 12.84 deg/7 deg on-axis and bent-nose biconics in air at Mach 6

Pressure distributions and shock shapes on a spherically blunted, 12.84 deg /7 deg on axis biconic and a spherically blunted, 12.84 deg/7 deg bent nose biconic at Mach 6 in air were measured. The angle of attack, referenced to the axis of aft cone, was varied from 0 deg to 25 deg in nominal 5 deg increments. Two values of free stream Reynolds number based on model length were tested. Predictions from simple, theories and from a supersonic, three dimensional, external invsicid code (STEIN) are compared with measured values. Predicted STEIN shock shapes and windward pressures are in agreement with measured values for both biconics over the present range of angle of attack.

Miller, C. G., III↗

NASA NTRS1982

Effect of rotor configuration on guyed tower and foundation designs and estimated costs for intermediate site horizontal axis wind turbines

Three designs of a guyed cylindrical tower and its foundation for an intermediate size horizontal axis wind turbine generator are discussed. The primary difference in the three designs is the configuration of the rotor. Two configurations are two-blade rotors with teetering hubs - one with full span pitchable blades, the other with fixed pitch blades. The third configuration is a three-bladed rotor with a rigid hub and fixed pitch blades. In all configurations the diameter of the rotor is 38 meters and the axis of rotation is 30.4 meters above grade, and the power output is 200 kW and 400 kW. For each configuration the design is based upon for the most severe loading condition either operating wind or hurricane conditions. The diameter of the tower is selected to be 1.5 meters (since it was determined that this would provide sufficient space for access ladders within the tower) with guy rods attached at 10.7 meters above grade. Completing a design requires selecting the required thicknesses of the various cylindrical segments, the number and diameter of the guy rods, the number and size of soil anchors, and the size of the central foundation. The lower natural frequencies of vibration are determined for each design to ensure that operation near resonance does not occur. Finally, a cost estimate is prepared for each design. A preliminary design and cost estimate of a cantilever tower (cylindrical and not guyed) and its foundation is also presented for each of the three configurations.

Frederick, G. R.↗

NASA NTRS1981

Downwind rotor horizontal axis wind turbine noise prediction

NASA and industry are currently cooperating in the conduct of extensive experimental and analytical studies to understand and predict the noise of large, horizontal axis wind turbines. This effort consists of (1) obtaining high quality noise data under well controlled and documented test conditions, (2) establishing the annoyance criteria for impulse noise of the type generated by horizontal axis wind turbines with rotors downwind of the support tower, (3) defining the wake characteristics downwind of the axial location of the plane of rotation, (4) comparing predictions with measurements made by use of wake data, and (5) comparing predictions with annoyance criteria. The status of work by Hamilton Standard in the above areas which was done in support of the cooperative NASA and industry studies is briefly summarized.

Metzger, F. B.↗

NASA NTRS1982

Simplified aeroelastic modeling of horizontal axis wind turbines

Certain aspects of the aeroelastic modeling and behavior of the horizontal axis wind turbine (HAWT) are examined. Two simple three degree of freedom models are described in this report, and tools are developed which allow other simple models to be derived. The first simple model developed is an equivalent hinge model to study the flap-lag-torsion aeroelastic stability of an isolated rotor blade. The model includes nonlinear effects, preconing, and noncoincident elastic axis, center of gravity, and aerodynamic center. A stability study is presented which examines the influence of key parameters on aeroelastic stability. Next, two general tools are developed to study the aeroelastic stability and response of a teetering rotor coupled to a flexible tower. The first of these tools is an aeroelastic model of a two-bladed rotor on a general flexible support. The second general tool is a harmonic balance solution method for the resulting second order system with periodic coefficients. The second simple model developed is a rotor-tower model which serves to demonstrate the general tools. This model includes nacelle yawing, nacelle pitching, and rotor teetering. Transient response time histories are calculated and compared to a similar model in the literature. Agreement between the two is very good, especially considering how few harmonics are used. Finally, a stability study is presented which examines the effects of support stiffness and damping, inflow angle, and preconing.

Wendell, J. H.↗

NASA NTRS1982

Development of methodology for horizontal axis wind turbine dynamic analysis

Horizontal axis wind turbine dynamics were studied. The following findings are summarized: (1) review of the MOSTAS computer programs for dynamic analysis of horizontal axis wind turbines; (2) review of various analysis methods for rotating systems with periodic coefficients; (3) review of structural dynamics analysis tools for large wind turbine; (4) experiments for yaw characteristics of a rotating rotor; (5) development of a finite element model for rotors; (6) development of simple models for aeroelastics; and (7) development of simple models for stability and response of wind turbines on flexible towers.

Dugundji, J.↗

NASA NTRS1983

Aircraft body-axis rotation measurement system

A two gyro four gimbal attitude sensing system having gimbal lock avoidance is provided with continuous azimuth information, rather than roll information, relative to the magnetic cardinal headings while in near vertical attitudes to allow recovery from vertical on a desired heading. The system is comprised of a means for stabilizing an outer roll gimbal that is common to a vertical gyro and a directional gyro with respect to the aircraft platform which is being angularly displaced about an axis substantially parallel to the outer roll gyro axis. A means is also provided for producing a signal indicative of the magnitude of such displacement as an indication of aircraft heading. Additional means are provided to cause stabilization of the outer roll gimbal whenever the pitch angle of the aircraft passes through a threshold prior to entering vertical flight and destabilization of the outer roll gimbal upon passing through the threshold when departing vertical flight.

Cowdin, K. T.↗

NASA NTRS1984

Crack growth direction in unidirectional off-axis graphite epoxy

An anisotropic elasticity crack tip stress analysis is implemented using three crack extension direction criteria (the normal stress ratio, the tensor polynominal and the strain energy density) to predict the direction of crack extension in unidirectional off axis graphite-epoxy. The theoretical predictions of crack extension direction are then compared with experimental results for 15 deg off axis tensile coupons with center cracks. Specimens of various aspect ratios and crack orientations are analyzed. It is shown that only the normal stress ratio criterion predicts the correct direction of crack growth.

Herakovich, C. T.↗

NASA NTRS1984

Relative potentials of concentrating and two-axis tracking flat-plate photovoltaic arrays for central-station applications

The purpose of this study is to assess the relative economic potentials of concenrating and two-axis tracking flat-plate photovoltaic arrays for central-station applications in the mid-1990's. Specific objectives of this study are to provide information on concentrator photovoltaic collector probabilistic price and efficiency levels to illustrate critical areas of R&D for concentrator cells and collectors, and to compare concentrator and flat-plate PV price and efficiency alternatives for several locations, based on their implied costs of energy. To deal with the uncertainties surrounding research and development activities in general, a probabilistic assessment of commercially achievable concentrator photovoltaic collector efficiencies and prices (at the factory loading dock) is performed. The results of this projection of concentrator photovoltaic technology are then compared with a previous flat-plate module price analysis (performed early in 1983). To focus this analysis on specific collector alternatives and their implied energy costs for different locations, similar two-axis tracking designs are assumed for both concentrator and flat-plate options.

Borden, C. S.↗

NASA NTRS1986

Summary of tower designs for large horizontal axis wind turbines

Towers for large horizontal axis wind turbines, machines with a rotor axis height above 30 meters and rated at more than 500 kW, have varied in configuration, materials of construction, type of construction, height, and stiffness. For example, the U.S. large HAWTs have utilized steel truss type towers and free-standing steel cylindrical towers. In Europe, the trend has been to use only free-standing and guyed cylindrical towers, but both steel and reinforced concrete have been used as materials of construction. These variations in materials of construction and type of construction reflect different engineering approaches to the design of cost effective towers for large HAWTs. Tower designs are the NASA/DOE Mod-5B presently being fabricated. Design goals and requirements that influence tower configuration, height and materials are discussed. In particular, experiences with United States large wind turbine towers are elucidated. Finally, current trends in tower designs for large HAWTs are highlighted.

Frederick, G. R.↗

NASA NTRS1986

Low-loss off-axis feeds for symmetric dual-reflector antennas

Circularly symmetric, dual reflector, high gain antenna systems often require feeds placed off the system's axis because of the need for multiple feeds to use the reflector antenna. Also, the constraint requiring the hyperboloid or shaped subreflector to remain circularly symmetric is sometimes added. In a Cassegrainian system, the subreflector and feed may be rotated off axis around the paraboloid focus and retain main reflector focusing. However, substantial spillover results in considerable noise with a high gain/low noise temperature system. In a shaped system, the tilt of the shaped subreflector and feed together results in substantial defocusing as well as spillover noise. If the subreflector is tilted approximately one-half the angle of the feed tilt in either the Cassegrainian or the dual shaped reflector antenna, it is found that spillover and noise are substantially reduced with tolerable defocusing. An extensive numerical analysis of these effects was conducted to determine the characteristics of a planned 70-meter, dual shaped reflector versus Cassegrainian antenna and to gain some understanding of the cause of the observed effects.

Veruttipong, T.↗

NASA NTRS1986

Discharge cell for optogalvanic spectroscopy having orthogonal relationship between the probe laser and discharge axis

A method and apparatus for an optogalvanic spectroscopy system are disclosed. Orthogonal geometry exists between the axis of a laser probe beam and the axis of a discharge created by a pair of spaced apart and longituduinally aligned high voltage electrodes. The electrodes are movable to permit adjustment of the location of a point in the discharge which is to irradiated by a laser beam crossing the discharge region. The cell dimensions are selected so that the cross section of the discharge region is substantly comparable in size to the cross section of the laser beam passing orthogonally through the discharge region.

Webster, C. R.↗

NASA NTRS1985

Crack growth direction in unidirectional off-axis graphite-epoxy

Herakovich, C. T.↗

NASA NTRS1988

Experimental investigation of propfan aeroelastic response in off-axis flow with mistuning

Measured vibratory strain amplitudes from off-axis flow are compared for the blades of two, 8-bladed propfan model rotors with mistuning. One rotor had inherent mistuning. The other was intentionally mistuned by replacing every other blade of the first rotor with a blade of same geometry but different frequencies and mode shapes. The data shows that the intentional mistuning had a beneficial effect on the aeroelastic response of the propfan motors for a wide range of off-axis flow angles, blade pitch angles, and rotational speeds. Statistical trends of blade strain amplitudes are compared for both the rotors in terms of the ratio of the maximum to the mean and the coefficient of variation.

Mehmed, Oral↗

NASA NTRS1988

The two axis motion simulator for the large space simulator at ESTEC (European Space Research and Technology Center)

The Large Space Simulator at the European Space Research and Technology Center (ESTEC) has been recently equipped with a motion simulator capable of handling test items of 5 tons mass and having a volume of 7m in diameter and a length of 7m. The motion simulator has a modular set-up. It consists of a spinbox as a basic unit on which the test article is mounted and which allows continuous rotation (spin) . This spinbox can be used in two operational configurations; the spin axis is vertical to 30 degrees when mounted on a gimbalstand; and the spin axis is horizontal when mounted on a turntable-yoke combination. The turntable provides rotation within plus or minus 90 degrees. This configuration allows one to bring a test article to all possible relative positions viv-a-vis the sun vector (which is horizontal in this case). The spinbox allows fast rotation between 1 to 6 rpm or slow rotation between 1 to 25 rotations per day as well as positioning within plus or minus 0.4 degrees accuracy.

Beckel, Kurt A.↗

NASA NTRS1988

Three-axis attitude determination via Kalman filtering of magnetometer data

A three-axis Magnetometer/Kalman Filter attitude determination system for a spacecraft in low-altitude Earth orbit is developed, analyzed, and simulation tested. The motivation for developing this system is to achieve light weight and low cost for an attitude determination system. The extended Kalman filter estimates the attitude, attitude rates, and constant disturbance torques. Accuracy near that of the International Geomagnetic Reference Field model is achieved. Covariance computation and simulation testing demonstrate the filter's accuracy. One test case, a gravity-gradient stabilized spacecraft with a pitch momentum wheel and a magnetically-anchored damper, is a real satellite on which this attitude determination system will be used. The application to a nadir pointing satellite and the estimation of disturbance torques represent the significant extensions contributed by this paper. Beyond its usefulness purely for attitude determination, this system could be used as part of a low-cost three-axis attitude stabilization system.

Martel, Francois↗

NASA NTRS1988

Experimental investigation of propfan aeroelastic response in off-axis flow with mistuning

Mehmed, Oral↗

NASA NTRS1989

Nystagmus responses in a group of normal humans during earth-horizontal axis rotation

Horizontal eye movement responses to earth-horizontal yaw axis rotation were evaluated in 50 normal human subjects who were uniformly distributed in age (20-69 years) and each age group was then divided by gender. Subjects were rotated with eyes open in the dark, using clockwise and counter-clockwise 60 deg velocity trapezoids. The nystagmus slow component velocity is analyzed. It is shown that, despite large intersubject variability, parameters which describe earth-horizontal yaw axis responses are loosely interrelated, and some of them vary significantly with gender and age.

Wall, Conrad, III↗