Search NASA⌕ Search

SEARCH · Search NASA

Results for “ball milling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Functionalized Silicon Particles for Enhanced Half- and Full-Cell Cycling of Si-Based Li-Ion Batteries

Vinylene carbonate (VC) and polyethylene oxide (PEO) have been investigated as functional agents that mimic the solid electrolyte interphase (SEI) chemistry of silicon (Si). VC and PEO are known to contribute to the stability of Si-based lithium-ion batteries as an electrolyte additive and as a SEI component, respectively. In this work, covalent surface functionalization was achieved via a facile route, which involves ball-milling the Si particles with sacrificial VC and PEO. Thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), and magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy indicate that the additives are strongly bound to Si. In particular, MAS NMR shows Si–R or Si–O–R groups, which confirm functionalization of the Si after milling in VC or PEO. Particle size analysis by dynamic light scattering reveals that the additives facilitate particle size reduction and that the functionalized particles result in more stable dispersions based on zeta potential measurements. Raman mapping of the electrodes fabricated from the VC and PEO-coated active material with a polyacrylic acid (PAA) binder reveals a more homogenous distribution of Si and the carbon conductive additive compared to the electrodes prepared from the neat Si. Furthermore, the VC-milled Si strikingly exhibited the highest capacity in both half- and full-cell configurations, with more than 200 mAh g –1 measured capacity compared to the neat Si in the half-cell format. This is linked to an improved electrode processing based on the Raman and zeta potential measurements as well as a thinner SEI (with more organic components for the functionalized Si relative to the neat Si) based on XPS analysis of the cycled electrodes. In conclusion, the effect of binder was also investigated by comparing PAA with P84 (polyimide type), where an increased capacity is observed in the latter case.

25 ENERGY STORAGE↗
DOE OSTI2021

Probing Clustering Dynamics between Silicon and PAA or LiPAA Slurries under Processing Conditions

This work explores the complex interplay between slurry aggregation, agglomeration, and conformation (i.e., shape) of poly(acrylic acid) (PAA)- and lithiated PAA-based silicon slurries as a function of the shear rate and the resulting slurry homogeneity. These values were measured by small-angle neutron scattering (SANS) and rheology-coupled ultra-SANS at conditions relevant to battery electrode casting. Different binder solution preparation methods, either a ball milling (BM) process or a planetary centrifugal mixing (PCM) process, dramatically modify the resulting polymer dynamics and organization around a silicon material. This is due to the different energy profiles of mixing where the more violent and higher energy PCM causes extensive breakdown and reformation of the binder, which is now likely in a branched conformation, while the lower energy BM results in simply lower-molecular weight linear polymers. In conclusion, the breakdown and reorganization of the polymer structure affect silicon slurry homogeneity, which affects subsequent electrode architecture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Mechanocatalytic Ammonia Synthesis over TiN in Transient Microenvironments

Environmentally friendly and energy-efficient ways to produce ammonia are essential to meet global food demands. In this study, a new approach for ammonia production at nominally ambient conditions is introduced. As proof of concept, ammonia is synthesized mechanocatalytically by ball milling titanium in a continuous gas flow. The ammonia synthesis reaction is proposed to follow a transient Mars–van Krevelen mechanism under mechanically activated conditions, where molecular nitrogen incorporation into the titanium lattice and titanium nitride hydrogenation occur in thermodynamically distinct environments. X-ray powder diffraction and X-ray absorption spectroscopy confirm the formation of titanium nitride from titanium and N2. The reactivity of nitrided titanium supports that lattice nitrogen plays a role in ammonia formation. The in situ formed titanium nitride is catalytically active, and the nitride regeneration reaction is determined to be the rate-limiting step. A preliminary technoeconomic analysis shows that this approach could be feasible for distributed ammonia production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

4 V Na Solid State Batteries Enabled by a Scalable Sodium Metal Oxyhalide Solid Electrolyte

All-solid-state sodium batteries (ASSSBs) are viable candidates for large scale energy storage that could vie with lithium. Ductile solid catholytes for such cells that can be prepared without extensive ball milling and directly paired with high voltage sodium cathodes are lacking, however. We report a new amorphous fast Na-ion conducting metal oxychloride that meets these criteria, synthesized through a scalable and low-cost route based on a spontaneous solid-state reaction with simple short mixing and 100 °C annealing. It has an ionic conductivity of 1.2 mS·cm–1 and low activation energy of 0.31 eV. Due to its dual O2–/Cl– framework, it exhibits a high anodic potential of 4 V vs Na+/Na and good chemical/electrochemical compatibility with high voltage sodium cathode materials. ASSSBs consisting of the oxychloride solid electrolyte paired with a high voltage P2–Na2/3Ni1/3Mn2/3O2 cathode showed stable long-term cycling with a 4.0 V vs Na3Sn cutoff potential and even to 4.3 V.

solid-state electrolyte, solid-state batteries, Nu↗
DOE OSTI2024

Mechanochemical in Situ Encapsulation of Palladium in Covalent Organic Frameworks

Palladium-encapsulated covalent organic frameworks (Pd/COFs) have garnered enormous attention in heterogeneous catalysis. However, the dominant ex situ encapsulation synthesis is tedious (multistep), time-consuming (typically 4 days or more), and involves the use of noxious solvents. Here we develop a mechanochemical in situ encapsulation strategy that enables the one-step, time-efficient, and environmentally benign synthesis of Pd/COFs. By ball milling COF precursors along with palladium acetate (Pd(OAc) 2 ) in one pot under air at room temperature, Pd/COF hybrids were readily synthesized within an hour, exhibiting high crystallinity, uniform Pd dispersion, and superb scalability up to gram scale. Moreover, this versatile strategy can be extended to the synthesis of three Pd/COFs. Remarkably, the resulting Pd/DMTP-TPB showcases extraordinary activity (96-99% yield in 1 h at room temperature) and broad substrate scope (>10 functionalized biaryls) for the Suzuki-Miyaura coupling reaction of aryl bromides and arylboronic acids. Furthermore, the heterogeneity of Pd/DMTP-TPB is verified by recycling and leaching tests. Finally, the mechanochemical in situ encapsulation strategy disclosed herein paves a facile, rapid, scalable, and environmentally benign avenue to access metal/COF catalysts for efficient heterogeneous catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Thermoelectric Performance of the 2D Bi 2 Si 2 Te 6 Semiconductor

Bi 2 Si 2 Te 6 , a 2D compound, is a direct band gap semiconductor with an optical band gap of 0.25 eV, and is a promising thermoelectric material. Single-phase Bi 2 Si 2 Te 6 is prepared by a scalable ball-milling and annealing process and the highly densified polycrystalline samples are prepared by spark plasma sintering. Bi 2 Si 2 Te 6 shows a p-type semiconductor transport behavior and exhibits an intrinsically low lattice thermal conductivity of ~0.48 Wm -1 K -1 (cross-plane) at 573 K. The first-principles density functional theory calculations indicate that such low lattice thermal conductivity is derived from the interactions between acoustic phonons and low-lying optical phonons, local vibrations of Bi, the low Debye temperature and strong anharmonicity result from the unique 2D crystal structure and metavalent bonding of Bi 2 Si 2 Te 6 . The Bi 2 Si 2 Te 6 exhibits an optimal figure of merit ZT of ~0.51 at 623 K, which can be further enhanced by the substitution of Bi with Pb. Pb doping leads to a large increase in power factor S 2 σ, from ~4.0 μWcm -1 K- 2 of Bi 2 Si 2 Te 6 to ~8.0 μWcm -1 K -2 of Bi 1.98 Pb 0.02 Si 2 Te 6 at 775 K, owing to the increase in carrier concentration. Moreover, Pb doping induces a further reduction in the lattice thermal conductivity to ~0.38 Wm -1 K -1 (cross-plane) at 623 K in Bi 1.98 Pb 0.02 Si 2 Te 6 ,. The simultaneous optimization of the power factor and lattice thermal conductivity achieves a peak ZT of ~0.90 at 723 K and a high average ZT of ~0.66 at 400–773 K in Bi 1.98 Pb 0.02 Si 2 Te 6 .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Introduction of Chalcogenide Glasses to Additive Manufacturing: Nanoparticle Ink Formulation, Inkjet Printing, and Phase Change Devices Fabrication

Abstract Chalcogenide glasses are one of the most versatile materials that have been widely researched because of their flexible optical, chemical, electronic, and phase change properties. Their application is usually in the form of thin films, which work as active layers in sensors and memory devices. In this work, we investigate the formulation of nanoparticle ink of Ge–Se chalcogenide glasses and its potential applications. The process steps reported in this work describe nanoparticle ink formulation from chalcogenide glasses, its application via inkjet printing and dip-coating methods and sintering to manufacture phase change devices. We report data regarding nanoparticle production by ball milling and ultrasonication along with the essential characteristics of the formed inks, like contact angle and viscosity. The printed chalcogenide glass films were characterized by Raman spectroscopy, X-ray diffraction, energy dispersive spectroscopy and atomic force microscopy. The printed films exhibited similar compositional, structural, electronic and optical properties as the thermally evaporated thin films. The crystallization processes of the printed films are discussed compared to those obtained by vacuum thermal deposition. We demonstrate the formation of printed thin films using nanoparticle inks, low-temperature sintering and proof for the first time, their application in electronic and photonic temperature sensors utilizing their phase change property. This work adds chalcogenide glasses to the list of inkjet printable materials, thus offering an easy way to form arbitrary device structures for optical and electronic applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Impact of surface coating on electrochemical and thermal behaviors of a Li-rich Li 1.2 Ni 0.16 Mn 0.56 Co 0.08 O 2 cathode

Lithium-rich layered oxide materials are considered as potential cathode materials for future high-performance lithium-ion batteries (LIBs) owing to their high operating voltage and relatively high specific capacity. However, perceptible issues such as poor rate performance, poor capacity retention, and voltage degradation during cycling need to be improved before the successful commercialization of the material. In this report, zirconia coated Li 1.2 Ni 0.16 Mn 0.56 Co 0.08 O 2 2 = 1.0, 1.5 and 2.0 wt%) materials are synthesized using a sol–gel assisted ball milling approach. A comparison of structural, morphological and electrochemical properties is examined to elucidate the promising role of ZrO 2 coating on the performance of the NMC cathode. A uniform and homogeneous ZrO 2 coating is observed on the surface of NMC particles as evident by TEM elemental mapping images. The ZrO 2 coated NMCs exhibit significantly improved electrochemical performance at a higher C-rate as compared to pristine material. 1.5% ZrO 2 coated NMC demonstrates better cycling stability (95% capacity retention) than pristine NMC (77% capacity retention) after 50 cycles. All ZrO 2 coated NMC materials demonstrated improved thermal stability compared to pristine material. The difference in onset temperature of 2 wt% ZrO 2 coated and pristine NMC is 20 °C. The improved electrochemical performance of ZrO 2 coated NMC can be attributed to the stabilization of its surface structure due to the presence of ZrO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Encapsulated Sb and Sb 2 O 3 particles in waste-tire derived carbon as stable composite anodes for sodium-ion batteries

A conductive network of waste-tire derived carbon (WTC) was used to produce homogeneous Sb/WTC and Sb 2 O 3 /WTC composite materials via ball milling as promising anodes for sodium-ion batteries (SIBs). Highly reversible redox peaks at 0.81/0.71, 0.25 V for Sb/WTC and 0.80/0.76, 0.21/0.26 V for Sb 2 O 3 /WTC anodes have been observed related to Na + intercalation and deintercalation in carbon and Na–Sb and Na 3 Sb as plausible conversion/alloy reactions. Sodium half-cells delivered reversible discharge capacities of 206 mA h g -1 and 207 mA h g -1 at a current density of 37 mA g -1 for the composite Sb/WTC and Sb 2 O 3 /WTC materials, respectively. Both the Sb/WTC and Sb 2 O 3 /WTC composite materials showed impressive capacity retention with 85% and 88%, respectively after 100 cycles. Furthermore, rate capability studies at 60 °C yielded an enhanced capacity of 240 mA h g -1 for Sb/WTC and 300 mA h g -1 for Sb 2 O 3 /WTC at 37 mA g -1 .

25 ENERGY STORAGE↗
DOE OSTI2021

Room temperature facile synthesis of olivine-Co 2 SiO 4 nanoparticles utilizing a mechanochemical method

Co 2 SiO 4 is a ceramic pigment and promising battery material of significant technological interest, as well as a model end-member of one of the most important mineral families in the Earth's crust and upper mantle. All previously developed methods for synthesis of Co 2 SiO 4 require high-temperature processing, which promotes grain growth, while the nanocrystalline form is required for some important technological applications. Here, we report a successful method for synthesizing nanocrystalline Co 2 SiO 4 via a simple and inexpensive high-energy ball milling mechanochemical process. Products of the synthesis were characterized by a combination of XRD and TEM, and their crystal structures and elemental compositions are reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Ambient mechanosynthesis of flexible two-dimensional covalent organic frameworks

We present the first ambient mechanosynthesis of 16 flexible covalent organic frameworks (COFs) within an hour. Notably, one representative COF exhibited a high iodine uptake capacity of ∼4.3 g g −1 from aqueous solutions and 5.97 g g −1 from vapor. Flexible two-dimensional covalent organic frameworks (2D COFs) constructed from nonplanar building blocks represent an emerging paradigm in COF design. Nevertheless, the prevailing solvothermal synthesis suffers from low time efficiency, environmental unfriendliness, and cumbersome protocols. Here, we address these challenges by developing the first ambient mechanosynthesis of a diverse library of flexible 2D COFs. Sixteen distinct triazine-cored Schiff-base COFs, including five as-yet-unreported ones, were rapidly synthesized via ball milling using 2,4,6-tris(4-aminophenoxy)-1,3,5-triazine (TPT-NH 2 ) and 2,4,6-tris(4-formylphenoxy)-1,3,5-triazine (TPT-CHO) as building blocks. Notably, the representative COF, MC-flexible-COF-1, was synthesized in as little as one hour under mechanosynthesis conditions, whereas it remained unattainable via the traditional solvothermal method, despite prolonged heating and extensive solvent screening. The highly dynamic nature of the imine linkage was unequivocally demonstrated through mechanochemical “scrambling” experiments using molecular model compounds. Furthermore, MC-flexible-COF-1 exhibited a high iodine uptake capacity of ∼4.30 g g −1 from aqueous solutions and 5.97 g g −1 from the vapor phase. This work underscores the immense potential of mechanochemistry as a powerful and sustainable tool for the rapid synthesis of advanced 2D COFs, including those inaccessible via conventional solution-based methods.

Nailwal, Yogendra↗
DOE OSTI2021

High-pressure high-temperature synthesis and thermal equation of state of high-entropy transition metal boride

High-entropy transition metal boride (Hf 0.2 Ti 0.2 Zr 0.2 Ta 0.2 Mo 0.2 )B 2 sample was synthesized under high-pressure and high-temperature starting from ball-milled oxide precursors (HfO 2 , TiO 2 , ZrO 2 , Ta 2 O 5 , MoO 3 ) mixed with graphite and boron-carbide. Experiments were conducted in a large-volume Paris Edinburgh press combined with an in-situ Energy Dispersive X-ray Diffraction. The hexagonal AlB 2 phase with an ambient pressure volume V 0 = 27.93 ± 0.03 Å 3 was synthesized at a pressure of 0.9 GPa and temperatures above 1373K. High-pressure high-temperature studies on the synthesized high-entropy transition metal boride sample were performed to 7.6 GPa and 1873 K. The thermal equation of state fitted to the experimental data resulted in an ambient pressure bulk-modulus K 0 = 344 ± 39 GPa, dK/dT = –0.108 ± 0.027 GPa/K, and a temperature dependent volumetric thermal expansion coefficient α = α 0 + α 1 T + α 2 T –2 . The thermal stability combined with a high bulk-modulus establishes this high-entropy transition metal boride as an ultrahard high-temperature ceramic material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Low temperature tetragonal polymorph of CaZrF 6

A new tetragonal polymorph of CaZrF 6 can be prepared by high energy ball milling of a CaF 2 /ZrF 4 mixture, followed by heat treatment at 325 °C. This polymorph is thermodynamically stable with respect to the well-known cubic form at low temperatures. However, it readily transforms to the cubic form on heating above ~400 °C. The tetragonal (β) CaZrF 6 is not isostructural with any previously known alkaline earth AZrF 6 phase. Unlike the cubic form, which shows strong negative thermal expansion over a wide temperature range, the tetragonal form displays positive thermal expansion in all directions (100–400 K: α l ~ +17 × 10 –6 K –1 and +13 × 10 –6 K –1 along the a- and c-axes, respectively).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dual-phase superconductivity in high-pressure high-temperature synthesized TaNbZrHfTi

We report on a novel TaNbZrHfTi-based high entropy alloy (HEA) which demonstrates distinctive dual-phase superconductivity. The HEA was synthesized under high pressures and high temperatures starting from a ball milled mixture of elemental metals in a large-volume Paris–Edinburgh cell with P ≈ 6 GPa and T = 2300 K. The synthesized HEA is a phase mixture of BCC (NbTa)0.45(ZrHfTi)0.55 with Tc1 = 6 K and FCC (NbTa)0.04(ZrHfTi)0.96 with Tc2 = 3.75 K. The measured magnetic field parameters for the HEA are lower critical field, Hc1(0) = 31 mT, and a relatively high upper critical field, Hc2(0) = 4.92 T. This dual-phase system is further characterized by the presence of a second magnetization peak, or the fishtail effect, observed in the virgin magnetization curves. This phenomenon, which does not distort the field-dependent magnetization hysteresis loops, suggests intricate pinning mechanisms that could be potentially tuned for optimized performance. The manifestation of these unique features in HEA superconductivity reinforces phase-dependent superconductivity and opens new avenues in the exploration of novel superconducting materials.

Materials Science↗
DOE OSTI2020

Grain size and structure distortion characterization of α-MgAgSb thermoelectric material by powder diffraction

Nanostructuring, structure distortion and/or disorder are the main manipulation techniques to reduce the lattice thermal conductivity and improve the figure of merit of thermoelectric materials. A single-phase α-MgAgSb sample, MgAg 0.97 Sb 0.99 , with high thermoelectric performance in near room temperature region was synthesized through a high-energy ball milling with a hot-pressing method. In this work, we report the average grain size of 24-28 nm and the accurate structure distortion, which are characterized by high-resolution neutron diffraction and synchrotron X-ray diffraction with Rietveld refinement data analysis. Both the small grain size and the structure distortion have a contribution to the low lattice thermal conductivity in MgAg 0.97 Sb 0.99 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Optical properties of hydrothermally synthesized Ti 3 C 2 T X MXene quantum dots and their application in biosensor

The remarkable properties of Ti 3 C 2 T X MXene quantum dots (MQDs) highlight their potential in diverse fields, including domains such as biocompatible nanoprobe, ion sensing, energy applications etc. Given their relevance in emerging technologies, a systematic study of their optical properties is crucial. MXene nanosheets were utilized in Acetylcholinesterase (AChE) based biosensors for the detection of organophosphate (OP) pesticides, this suggests there is significant potential for further development of electrochemical biosensor by incorporating MQDs in this field. The synthesis of MQDs has been achieved through various methods, either individually or in combination of methods, including hydrothermal, acoustic microfluidic, electrochemical, ball milling etc. Furthermore, we synthesized Ti 3 C 2 T X MQDs using hydrothermal method and characterized using atomic force microscopy, optical spectroscopy and cyclic voltammetry.

36 MATERIALS SCIENCE↗