Search NASA⌕ Search

SEARCH · Search NASA

Results for “batch simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Development of advanced methods for continuous Czochralski growth. Silicon sheet growth development for the large area silicon sheet task of the low cost silicon solar array project

The three components required to modify the furnace for batch and continuous recharging with granular silicon were designed. The feasibility of extended growth cycles up to 40 hours long was demonstrated by a recharge simulation experiment; a 6 inch diameter crystal was pulled from a 20 kg charge, remelted, and pulled again for a total of four growth cycles, 59-1/8 inch of body length, and approximately 65 kg of calculated mass.

Wolfson, R. G.↗
NASA NTRS1995

In-plant testing of membranes to treat electroplating wastewater

This is the final report submitted for the work performed under the NASA Cooperative Agreement NCC3-301 for the project entitled 'In-Plant Testing of Membranes To Treat Electroplating Waste water'. The main objective of the research project was to determine if the crosslinked polyacrylic acid salt films developed by NASA scientists could be used for heavy metal removal from the wastewater generated by the metals-finishing or electroplating industry. A variety of tasks identified in the original proposal were completed. These included: (1) analysis of our industrial partner Aetna Plating's zinc electroplating process and its wastewater treatment needs for zinc removal; (2) design and construction of a laboratory-scale unit to continuously supply and remove the ion exchange films from the zinc wastewater; (3) performance of a series of runs on such a unit to determine its operating characteristics; and (4) design of a prototype unit for use at the industrial site. In addition, there were a number of tasks that had not been identified in the original proposal but were later judged to be necessary for the successful completion of the project. These were: (1) batch equilibrium and kinetic experiments with analysis of the experimental results to accurately determine the equilibrium and kinetic parameters for the ion exchange films; (2 ) simulation studies for proper design of the prototype unit; and (3) preliminary runs to exchange the films from H form to Calcium form.

Shah, D. B.↗
NASA NTRS1988

Trajectory computation during a maneuver: Thrust estimation with the Goddard Trajectory Determination System (GTDS)

Existing thrust modeling capabilities of the Goddard Trajectory Determination System (GTDS) have been enhanced to allow calibration of the onboard propulsion system. These enhancements provide one or more thrust scale factors, based on estimation using the batch least-squares technique, for the case of along-track thrust and the case of attitude-dependent thrust. The enhancements are evaluated using simulated tracking measurements for a test spacecraft and using actual tracking measurements for the Earth Radiation Budget Satellite (ERBS). The effects of tracking measurement noise and distribution on the accuracy of the estimation are investigated and found to be significant. Results and conclusions of the analysis are presented.

Beri, A. C.↗
NASA NTRS2019

Real-Time Estimation of Bare-Airframe Frequency Responses from Closed-Loop Data and Multisine Inputs

A method is presented for computing frequency responses of multiple-input multiple-output bare-airframe dynamics from flight test data containing feedback control and/or mixing of control effectors. Orthogonal phase-optimized multisines are used to simultaneously excite each input with unique harmonic frequencies, at which frequency responses are computed as ratios of output-to-input Fourier transform data. The confounding effects of feedback and mixing for frequency response estimation are resolved by interpolating the frequency responses among all the harmonic frequencies. The method can be run in batch for post-flight analysis, or in real time as the aircraft is flying. The effectiveness of the method was verified using closed-loop simulations of the subscale NASA T-2 generic transport airplane. The method was also demonstrated using flight test data from the X-56A MUTT aeroelastic airplane, which was flown with feedback control and mixing.

Jared A Grauer↗
NASA NTRS2000

ICEG2D: An Integrated Software Package for Automated Prediction of Flow Fields for Single-Element Airfoils with Ice Accretion

An integrated software package, ICEG2D, was developed to automate computational fluid dynamics (CFD) simulations for single-element airfoils with ice accretion. ICEG2D is designed to automatically perform three primary functions: (1) generating a grid-ready, surface definition based on the geometrical characteristics of the iced airfoil surface, (2) generating a high-quality grid using the generated surface point distribution, and (3) generating the input and restart files needed to run the general purpose CFD solver NPARC. ICEG2D can be executed in batch mode using a script file or in an interactive mode by entering directives from a command line. This report summarizes activities completed in the first year of a three-year research and development program to address issues related to CFD simulations for aircraft components with ice accretion. Specifically, this document describes the technology employed in the software, the installation procedure, and a description of the operation of the software package. Validation of the geometry and grid generation modules of ICEG2D is also discussed.

Thompson, David S.↗
NASA NTRS1994

Application of a Monte Carlo accuracy assessment tool to TDRS and GPS

In support of a NASA study on the application of radio interferometry to satellite orbit determination, MITRE developed a simulation tool for assessing interferometric tracking accuracy. Initially, the tool was applied to the problem of determining optimal interferometric station siting for orbit determination of the Tracking and Data Relay Satellite (TDRS). Subsequently, the Orbit Determination Accuracy Estimator (ODAE) was expanded to model the general batch maximum likelihood orbit determination algorithms of the Goddard Trajectory Determination System (GTDS) with measurement types including not only group and phase delay from radio interferometry, but also range, range rate, angular measurements, and satellite-to-satellite measurements. The user of ODAE specifies the statistical properties of error sources, including inherent observable imprecision, atmospheric delays, station location uncertainty, and measurement biases. Upon Monte Carlo simulation of the orbit determination process, ODAE calculates the statistical properties of the error in the satellite state vector and any other parameters for which a solution was obtained in the orbit determination. This paper presents results from ODAE application to two different problems: (1)determination of optimal geometry for interferometirc tracking of TDRS, and (2) expected orbit determination accuracy for Global Positioning System (GPS) tracking of low-earth orbit (LEO) satellites. Conclusions about optimal ground station locations for TDRS orbit determination by radio interferometry are presented, and the feasibility of GPS-based tracking for IRIDIUM, a LEO mobile satellite communications (MOBILSATCOM) system, is demonstrated.

Pavloff, Michael S.↗
NASA NTRS1975

A Standard Kinematic Model for Flight Simulation at NASA Ames

A standard kinematic model for aircraft simulation exists at NASA-Ames on a variety of computer systems, one of which is used to control the flight simulator for advanced aircraft (FSAA). The derivation of the kinematic model is given and various mathematical relationships are presented as a guide. These include descriptions of standardized simulation subsystems such as the atmospheric turbulence model and the generalized six-degrees-of-freedom trim routine, as well as an introduction to the emulative batch-processing system which enables this facility to optimize its real-time environment.

Mcfarland, R. E.↗
NASA NTRS1986

Estimating Transient Pressure Surges in Cryogenic Systems

Potentially-damaging pressure waves anticipated and, therefore, avoided. Mathematical model developed for prediction of pressure behavior in single-and two-phase cryogenic systems. Transient liquid-flow analysis modified to incorporate behavior of vapor bubbles and used to predict maximum pressure in cryogenic transfer systems consisting of complex pipe and valve arrangements under both steady-state and transient conditions. Simulation compared favorably with data obtained during transfer of liquid oxygen from ground storage tanks to Space Shuttle orbiter external tanks. Program written in FORTRAN 77 for batch execution.

Pfister, P.↗
NASA NTRS2010

Performance Testing of Molten Regolith Electrolysis with Transfer of Molten Material for the Production of Oxygen and Metals on the Moon

Previously, we have demonstrated the production of oxygen by electrolysis of molten regolith simulants at temperatures near 1600 C. Using an inert anode and suitable cathode, direct electrolysis (no supporting electrolyte) of the molten silicate is carried out, resulting in the production of molten metallic products at the cathode and oxygen gas at the anode. Initial direct measurements of current efficiency have confirmed that the process offer potential advantages of high oxygen production rates in a smaller footprint facility landed on the moon, with a minimum of consumables brought from Earth. We now report the results of a scale-up effort toward the goal of achieving production rates equivalent to 1 metric ton O2/year, a benchmark established for the support of a lunar base. We previously reported on the electrochemical behavior of the molten electrolyte as dependent on anode material, sweep rate and electrolyte composition in batches of 20-200g and at currents of less than 0.5 A. In this paper, we present the results of experiments performed at currents up to 10 Amperes) and in larger volumes of regolith simulant (500 g - 1 kg) for longer durations of electrolysis. The technical development of critical design components is described, including: inert anodes capable of passing continuous currents of several Amperes, container materials selection, direct gas analysis capability to determine the gas components co-evolving with oxygen. To allow a continuous process, a system has been designed and tested to enable the withdrawal of cathodically-reduced molten metals and spent molten oxide electrolyte. The performance of the withdrawal system is presented and critiqued. The design of the electrolytic cell and the configuration of the furnace were supported by modeling the thermal environment of the system in an effort to realize a balance between external heating and internal joule heating. We will discuss the impact these simulations and experimental findings have on the design of a suitable prototype for lunar applications

Sibille, Laurent↗
NASA NTRS1993

Stellar Photometry Software

We describe the Stellar Photometry Software (SPS), which combines in a single program procedures for locating stars, computing a mean stellar point-spread function (PSF), and performing aperture and/or multiple PSF-fitting photometry, along with related bookkeeping functions. The software can be run either interactively or in batch mode on computers using the UNIX operating system. The performance of SPS is compared to that of the photometry programs DoPHOT and IRAF/DAOPHOT, using both real and simulated CCD observations. A direct comparison of the instrumental magnitudes shows that all three programs produce comparable results.

Janes, Kenneth A.↗
NASA NTRS1981

Algorithms for onboard orbit estimation with Tracking and Data Relay Satellite System data

An investigation is carried out to determine an appropriate estimation technique for onboard orbit determination using simulated Tracking and Data Relay Satellite System (TDRSS) data. Results are presented from studies done using three estimation techniques: an extended Kalman filter, a consider filter, and a sliding batch differential corrector. These estimators are evaluated when used with both baseline and worst-case TDRSS measurement errors and with tracking configurations for two types of orbits: a high-inclination, near-circular orbit with an altitude of 700 km and a moderately inclined, lower altitude orbit. Each estimation result is evaluated by comparing the true with the estimated ephemeris.

Dunham, J. B.↗
NASA NTRS1990

Comparison and testing of extended Kalman filters for attitude estimation of the Earth Radiation Budget Satellite

This paper presents the testing and comparison of two extended Kalman filters (EKFs) developed for the Earth Radiation Budget Satellite (ERBS). One EKF updates the attitude quaternion using a four-component additive error quaternion. This technique is compared to that of a second EKF, which uses a multiplicative error quaternion. Brief developments of the algorithms are included. The convergence properties, singularity problems, and normalization techniques of the two filters are addressed. Both filters are tested with simulated ERBS sensor data in addition to real ERBS sensor data. The results of the two filters are also compared to those from the ERBS operational ground support software, which uses a batch differential correction algorithm to estimate attitude and gyro biases.

Bar-Itzhack, Itzhack Y.↗
NASA NTRS2012

Operational Improvements From the Automatic Dependant Surveillance Broadcast In-Trail Procedure in the Pacific Organized Track System

The Federal Aviation Administration's Surveillance and Broadcast Services Program has supported implementation of the Automatic Dependant Surveillance Broadcast (ADS-B) In-Trail Procedure (ITP) on commercial revenue flights. ADS-B ITP is intended to be used in non-radar airspace that is employing procedural separation. Through the use of onboard tools, pilots are able to make a new type of altitude change request to an Air Traffic Service Provider (ATSP). The FAA, in partnership with United Airlines, is conducting flight trials of the ITP in revenue service in the Pacific. To support the expansion of flight trials to the rest of the US managed Pacific Airspace Region, a computerized batch study was conducted to investigate the operational impacts and potential benefits that can be gained through the use of the ITP in the Pacific Organized Track System (PACOTS). This study, which simulated the Oakland managed portion of the PACOTS, suggests that potential benefits in the PACOTS are significant with a considerable increase in time spent at optimum altitude and associated fuel savings.

Chartrand, Ryan C.↗
NASA NTRS2001

ICEG2D (v2.0) - An Integrated Software Package for Automated Prediction of Flow Fields for Single-Element Airfoils With Ice Accretion

An integrated geometry/grid/simulation software package, ICEG2D, is being developed to automate computational fluid dynamics (CFD) simulations for single- and multi-element airfoils with ice accretions. The current version, ICEG213 (v2.0), was designed to automatically perform four primary functions: (1) generate a grid-ready surface definition based on the geometrical characteristics of the iced airfoil surface, (2) generate high-quality structured and generalized grids starting from a defined surface definition, (3) generate the input and restart files needed to run the structured grid CFD solver NPARC or the generalized grid CFD solver HYBFL2D, and (4) using the flow solutions, generate solution-adaptive grids. ICEG2D (v2.0) can be operated in either a batch mode using a script file or in an interactive mode by entering directives from a command line within a Unix shell. This report summarizes activities completed in the first two years of a three-year research and development program to address automation issues related to CFD simulations for airfoils with ice accretions. As well as describing the technology employed in the software, this document serves as a users manual providing installation and operating instructions. An evaluation of the software is also presented.

Thompson David S.↗
NASA NTRS1986

Aircraft Takeoff and Landing Analysis

Behavior of flexible or rigid aircraft simulated under variety of conditions. Active Gear, Flexible Aircraft Takeoff and Landing Analysis program, AGFATL, completely simulates aircraft takeoff and landing dynamics. AGFATL represents airplane either as rigid body with six degrees of freedom or as flexible body with multiple degrees of freedom. AGFATL written in FORTRAN IV for batch execution.

Mcgehee, J. R.↗
NASA NTRS2011

Comparison of Four Strong Acids on the Precipitation Potential of Gypsum in Brines During Distillation of Pretreated, Augmented Urine

Two batches of nominally pretreated and augmented urine were prepared with the baseline pretreatment formulation of sulfuric acid and chromium trioxide. The urine was augmented with inorganic salts and organic compounds in order to simulate a urinary ionic concentrations representing the upper 95 percentile on orbit. Three strong mineral acids: phosphoric, hydrochloric, and nitric acid, were substituted for the sulfuric acid for comparison to the baseline sulfuric acid pretreatment formulation. Three concentrations of oxidizer in the pretreatment formulation were also tested. Pretreated urine was distilled to 85% water recovery to determine the effect of each acid and its conjugate base on the precipitation of minerals during distillation. The brines were analyzed for calcium and sulfate ion, total, volatile, and fixed suspended solids. Test results verified that substitution of phosphoric, hydrochloric, or nitric acids for sulfuric acid would prevent the precipitation of gypsum up to 85% recovery from pretreated urine representing the upper 95 percentile calcium concentration on orbit.

Muirhead, Dean↗
NASA NTRS2008

Real-Time Dynamic Modeling - Data Information Requirements and Flight Test Results

Practical aspects of identifying dynamic models for aircraft in real time were studied. Topics include formulation of an equation-error method in the frequency domain to estimate non-dimensional stability and control derivatives in real time, data information content for accurate modeling results, and data information management techniques such as data forgetting, incorporating prior information, and optimized excitation. Real-time dynamic modeling was applied to simulation data and flight test data from a modified F-15B fighter aircraft, and to operational flight data from a subscale jet transport aircraft. Estimated parameter standard errors and comparisons with results from a batch output-error method in the time domain were used to demonstrate the accuracy of the identified real-time models.

Morelli, Eugene A.↗
NASA NTRS2012

A Look at the Impact of High-End Computing Technologies on NASA Missions

From its bold start nearly 30 years ago and continuing today, the NASA Advanced Supercomputing (NAS) facility at Ames Research Center has enabled remarkable breakthroughs in the space agency s science and engineering missions. Throughout this time, NAS experts have influenced the state-of-the-art in high-performance computing (HPC) and related technologies such as scientific visualization, system benchmarking, batch scheduling, and grid environments. We highlight the pioneering achievements and innovations originating from and made possible by NAS resources and know-how, from early supercomputing environment design and software development, to long-term simulation and analyses critical to design safe Space Shuttle operations and associated spinoff technologies, to the highly successful Kepler Mission s discovery of new planets now capturing the world s imagination.

Biswas, Rupak↗