Search NASA⌕ Search

SEARCH · Search NASA

Results for “buffer layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Molecular beam epitaxy growth of PbSe on Si (211) using a ZnTe buffer layer

The authors report the results of successful growth of single crystalline PbSe on Si (211) substrates with ZnTe as a buffer layer by molecular beam epitaxy. Single crystalline PbSe with (511) orientation was achieved on ZnTe/Si (211), as evidenced by RHEED patterns indicative of 2 dimensional (2D) growth, x ray diffraction rocking curves with a full width at half maximum as low as 153 arc sec and mobility as large as 1.1x10{sup 4}cm{sup 2}V{sup -1}s{sup -1} at 77 K. Cross hatch patterns were found on the PbSe(511) surface in Nomarski filtered microscope images suggesting the presence of a surface thermal strain relaxation mechanism, which was confirmed by Fourier transformed high resolution transmission electron microscope images.

36 MATERIALS SCIENCE↗

Optical, structural, and chemical properties of flash evaporated In{sub 2}S{sub 3} buffer layer for Cu(In,Ga)Se{sub 2} solar cells

In{sub 2}S{sub 3} layers were deposited by flash evaporation technique with varying flash rates. The optical constants of layers based on Tauc-Lorentz model dielectric function were extracted from spectroscopic ellipsometry measurements. X-ray photoelectron spectroscopic investigation revealed the presence of oxygen impurity in as-deposited and air-annealed layers with traces of Na inclusion in the layer grown at high flash rate. The enhancement in crystalline arrangement of as-deposited layer after air annealing was confirmed by Raman spectroscopy. Rutherford backscattering measurements revealed the growth of off-stoichiometric layers at all flash rates. An analytical layer growth model has been proposed supporting the results obtained by various layer characterization techniques. The solar cells were prepared with flash evaporated In{sub 2}S{sub 3} buffer layers and their performances were compared with CdS reference solar cell. A significant gain in short-circuit current was obtained after air annealing of the complete device at 200 deg. C for 20 min. A maximum conversion efficiency of 12.6% was delivered by a high flash rate In{sub 2}S{sub 3} buffered cell with open-circuit voltage close to that of CdS reference cell. The improvement in device performance after air annealing treatment is explained by thermally enhanced Cu and oxygen diffusion from Cu(In,Ga)Se{sub 2} and i-ZnO to In{sub 2}S{sub 3} layer, respectively.

36 MATERIALS SCIENCE↗

Influence of a TiO{sub 2} buffer layer on the magnetic properties of anatase Co:TiO{sub 2} thin films

Our study addresses the influence of a TiO{sub 2} buffer layer on the morphological, structural, and magnetic properties of Co:TiO{sub 2} films grown on (001) SrTiO{sub 3} substrates by RF sputtering. We demonstrate that a direct correlation exist between the morphology, the Co heterogeneity, and the magnetic properties measured in the films. Correlated analysis by cross section transmission electron microscopy, energy dispersive x-ray, and x-ray photoemission spectroscopy reveals that the Co is not uniformly distributed in the film but concentrated in the surface clusters. Atomic force microscopy analysis illustrates that the unbuffered films present a large density of surface clusters. These clusters are not metallic Co but Co rich TiO{sub 2} anatase phase and they are accompanied by structural defects in the film: dislocations, small angle grain boundaries. Magnetometry analysis shows that the unbuffered films have a net ferromagnetic behavior, while in the buffered ones the ferromagnetism is quenched. Therefore, we conclude that the magnetism in unbuffered samples is related to the surface clusters and seems to have an extrinsic nature.

36 MATERIALS SCIENCE↗

Integration and structural analysis of strain relaxed bi-epitaxial zinc oxide(0001) thin film with silicon(100) using titanium nitride buffer layer

Epitaxial growth of c-plane ZnO(0001) has been demonstrated on the Si(001) by using TiN as an intermediate buffer layer. Because of different out of plane symmetry of the substrate (Si/TiN) and the film (ZnO), two orientations of ZnO domains were obtained and the ZnO film growth is of bi-epitaxial nature. The ZnO thin film was observed to be nearly strain relaxed from X-ray and Raman measurements. The interface between the ZnO and TiN was investigated by transmission electron microscopy, and atomic arrangement has been modeled to understand the crystallographic orientation and structure of the domain/grain boundaries. Reaction at ZnO/TiN interface at higher growth temperature causing zinc titanate formation was observed. The grain boundary structure between the observed domains investigated by scanning transmission electron microscopy, revealed the ZnO(0001) planes to be contiguous across the grain boundary which is significant from the perspective of conduction electron scattering. In this configuration, the TiN (being electrically conductive) can be effectively used as an electrode for novel vertically integrated device applications (like light emitting diodes) directly on Si(100) substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Development of Solution Buffer Layers for RABiTS Based YBCO Coated Conductors

The main objective of this research is to find a suitable alternate solution based seed layer for the standard RABiTS three-layer architecture of physical vapor deposited CeO2 cap/YSZ barrier/Y2O3 seed on Ni-5%W metal tape. In the present work, we have identified CeO2 buffer layer as a potential replacement for Y2O3 seeds. Using a metal-organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of CeO2 (both pure and Zr, Cu and Gd-doped) directly on biaxially textured Ni-5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial CeO2 phase with slightly improved out-of-plane texture compared to the texture of underlying Ni-W substrates can be achieved in pure, undoped CeO2 samples. We have also demonstrated the growth of YSZ barrier layers on pure CeO2 seeds using sputtering. Both sputtered CeO2 cap layers and MOD-YBCO films were grown epitaxially on these YSZ-buffered MOD-CeO2/Ni-5W substrates. High critical currents per unit width, Ic of 264 A/cm (critical current density, Jc of 3.3 MA/cm2) at 77 K and 0.01 T was achieved for 0.8 m thick MOD-YBCO films grown on MOD-CeO2 seeds. These results indicate that CeO2 films can be grown directly on Ni-5W substrates and still support high performance YBCO coated conductors. This work holds promise for a route for producing low-cost buffer architecture for RABiTS based YBCO coated conductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of Solution Buffer Layers for RABiTS Based YBCO Coated Conductors

Abstract The main objective of this research is to find a suitable alternate solution based seed layer for the standard RABiTS three-layer architecture of physical vapor deposited CeO cap/YSZ barrier/Y O seed on Ni-5%W metal tape. In the present work, we have identified CeO buffer layer as a potential replacement for Y O seeds. Using a metal-organic deposition (MOD) process, we have grown smooth, crack-free, epitaxial thin films of CeO (pure and Zr, Cu and Gd-doped) directly on biaxially textured Ni-5W substrates in short lengths. Detailed XRD studies indicate that a single epitaxial CeO phase with slightly improved out-of-plane texture compared to the texture of the underlying Ni-W substrates can be achieved in pure, undoped CeO samples. We have also demonstrated the growth of YSZ barrier layers on pure CeO seeds using sputtering. Both sputtered CeO cap layers and MOD-YBCO films were grown epitaxially on these YSZ-buffered MOD-CeO /Ni-5W substrates. High critical currents per unit width, of 264 A/cm (critical current density, of 3.3 MA/cm ) at 77 K and 0.01 T was achieved for 0.8 m thick MOD-YBCO films grown on MOD-CeO seeds. These results indicate that CeO films can be grown directly on Ni-5W substrates and still support high performance YBCO coated conductors. This work holds promise for a route for producing low-cost buffer architecture for RABiTS based YBCO coated conductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of a Buffer Layer on the Formation of a Thin-Film Nickel Catalyst for Carbon Nanotube Synthesis

The formation of nanoparticles of a thin-film nickel catalyst applied on a buffer layer in the form of pure titanium, titanium oxide, or titanium nitride has been studied. It has been shown that if nanotubes are synthesized in three stages (oxidation, reduction, and growth of nanotubes), the situation may arise when the metallic catalyst becomes isolated from the surface, and hence, from the hydrocarbon flux, as a result of which the nanotube growth stops. Isolation takes place when the interface between titanium oxide and the gas phase in the reactor moves. In this case, titanium oxide goes round a nickel oxide nanoparticle and insulates it. The displacement rate of this interface and the coefficient of hydrogen diffusion in titanium dioxide have been determined.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optimal Cu buffer layer thickness for growing epitaxial Co overlayers on Si(111)7 x 7

Using scanning tunneling microscopy, reflection high energy diffraction and magnetic optical Kerr effect measurements, growth mode and the magnetic properties of epitaxial Co films on Si(111) with epitaxial Cu(111) buffer layers of various thicknesses have been studied. The strained 3.5-monolayer-thick Cu/Si(111) film has been found to be an optimal buffer, in which case an almost ideal layer-by-layer like growth of Co is observed up to six Co monolayers, due to a negligible lattice mismatch. The coercivity of Co films grown in this layer-by-layer like fashion has been determined to be about 10 Oe, testifying to the high quality of the formed Co film and Co/Cu interface. Changeover of the Co film growth mode from layer-by-layer like to multilayer has been found to result in the transition of the film magnetic properties from isotropic to markedly uniaxially anisotropic.

36 MATERIALS SCIENCE↗

Reduced dislocation density in Ga x In 1–x P compositionally graded buffer layers through engineered glide plane switch

In this work we develop control over dislocation glide dynamics in Ga x In 1-x P compositionally graded buffer layers (CGBs) through control of CuPt ordering on the group-III sublattice. The ordered structure is metastable in the bulk, so any glissile dislocation that disrupts the ordered pattern will release stored energy, and experience an increased glide force. Here we show how this connection between atomic ordering and dislocation glide force can be exploited to control the threading dislocation density (TDD) in Ga x In 1-x P CGBs. When ordered Ga x In 1-x P is graded from the GaAs lattice constant to InP, the order parameter ..eta.. decreases as x decreases, and dislocation glide switches from one set of glide planes to the other. This glide plane switch (GPS) is accompanied by the nucleation of dislocations on the new glide plane, which typically leads to increased TDD. We develop control of the GPS position within a Ga x In 1-x P CGB through manipulation of deposition temperature, surfactant concentration, and strain-grading rate. We demonstrate a two-stage Ga x In 1-x P CGB from GaAs to InP with sufficiently low TDD for high performance devices, such as the 4-junction inverted metamorphic multi-junction solar cell, achieved through careful control the GPS position. Here, experimental results are analyzed within the context of a model that considers the force balance on dislocations on the two competing glide planes as a function of the degree of ordering.

14 SOLAR ENERGY↗

Terahertz radiation in In{sub 0.38}Ga{sub 0.62}As grown on a GaAs wafer with a metamorphic buffer layer under femtosecond laser excitation

The results of time-domain spectroscopy of the terahertz (THz) generation in a structure with an In{sub 0.38}Ga{sub 0.62}As photoconductive layer are presented. This structure grown by molecular-beam epitaxy on a GaAs substrate using a metamorphic buffer layer allows THz generation with a wide frequency spectrum (to 6 THz). This is due to the additional contribution of the photo-Dember effect to THz generation. The measured optical-to-terahertz conversion efficiency in this structure is 10{sup –5} at a rather low optical fluence of ~40 μJ/cm{sup 2}, which is higher than that in low-temperature grown GaAs by almost two orders of magnitude.

36 MATERIALS SCIENCE↗

ZnO buffer layer for metal films on silicon substrates

Dramatic improvements in metallization integrity and electroceramic thin film performance can be achieved by the use of the ZnO buffer layer to minimize interfacial energy between metallization and adhesion layers. In particular, the invention provides a substrate metallization method utilizing a ZnO adhesion layer that has a high work of adhesion, which in turn enables processing under thermal budgets typically reserved for more exotic ceramic, single-crystal, or metal foil substrates. Embodiments of the present invention can be used in a broad range of applications beyond ferroelectric capacitors, including microelectromechanical systems, micro-printed heaters and sensors, and electrochemical energy storage, where integrity of metallized silicon to high temperatures is necessary.

36 MATERIALS SCIENCE↗

Coincident site lattice-matched growth of semiconductors on substrates using compliant buffer layers

A method of producing semiconductor materials and devices that incorporate the semiconductor materials are provided. In particular, a method is provided of producing a semiconductor material, such as a III-V semiconductor, on a silicon substrate using a compliant buffer layer, and devices such as photovoltaic cells that incorporate the semiconductor materials. The compliant buffer material and semiconductor materials may be deposited using coincident site lattice-matching epitaxy, resulting in a close degree of lattice matching between the substrate material and deposited material for a wide variety of material compositions. The coincident site lattice matching epitaxial process, as well as the use of a ductile buffer material, reduce the internal stresses and associated crystal defects within the deposited semiconductor materials fabricated using the disclosed method. As a result, the semiconductor devices provided herein possess enhanced performance characteristics due to a relatively low density of crystal defects.

36 MATERIALS SCIENCE↗

Tunable work function of a WO{sub x} buffer layer for enhanced photocarrier collection of pin-type amorphous silicon solar cells

An in situ postdeposition ultraviolet treatment was proposed to improve the electrical properties of a tungsten oxide (WO{sub x}) buffer layer of pin-type amorphous silicon-based solar cell. Based on the x-ray and ultraviolet photoelectron spectroscopy and the activation energy measurements, it was found that the work function of WO{sub x} is tunable by ultraviolet light treatment, and the collection performance of solar cells incorporating WO{sub x} with the lower work function is further improved. Moreover, the optimal band alignment scheme for a window layer is discussed in terms of obtaining enhanced carrier collection without open circuit voltage degradation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Degeneracy in Intercalated Pb Phases under Buffer-Layer Graphene on SiC(0001) and Diffuse Moiré Spots in Surface Diffraction

First-principles density functional theory (DFT) is used to analyze the stability of Pb intercalated phases under buffer layer graphene on SiC(0001) as a function of the supercell size, Pb coverage, and degree of Pb ordering. By comparing the chemical potentials of such two-dimensional Pb structures, here we find that there is a family of structurally distinct thermodynamically preferred Pb subsurface configurations with minute stability differences. These differences are comparable to the thermal energies at about 450 °C, where the Pb intercalated phases are grown. High-resolution surface-diffraction experiments using Spot Profile Analysis Low-Energy Electron Diffraction (SPA-LEED) confirm this high degree of degeneracy of the Pb intercalated phases from broad, low-intensity moiré spots observed exclusively from intercalated Pb. The low intensity of the moiré spots implies the coexistence of structurally different subsurface Pb phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The role of Ag buffer layer in Fe islands growth on Ge (111) surfaces

Sub-monolayer iron atoms were deposited at room temperature on Ge (111)-c(2 × 8) substrates with and without Ag buffer layers. The behavior of Fe islands growth was investigated by using scanning tunneling microscope (STM) after different annealing temperatures. STM images show that iron atoms will cause defects and holes on substrates at room temperature. As the annealing temperature rises, iron atoms pull out germanium to form various kinds of alloyed islands. However, the silver layer can protect the Ag/Ge(111)-(√3×√3) reconstruction from forming defects. The phase diagram shows that ring, dot, and triangular defects were only found on Ge (111)-c(2 × 8) substrates. The kinds of islands found in Fe/Ge system are similar to Fe/Ag/Ge system. It indicates that Ge atoms were pulled out to form islands at high annealing temperatures whether there was a Ag layer or not. But a few differences in big pyramidal or strip islands show that the silver layer affects the development of islands by changing the surface symmetry and diffusion coefficient. The structure characters of various islands are also discussed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Theoretical and experimental study of highly textured GaAs on silicon using a graphene buffer layer

A novel heteroepitaxial growth technique, quasi-van der Waals epitaxy, promises the ability to deposit three-dimensional GaAs materials on silicon using two-dimensional graphene as a buffer layer by overcoming the lattice and thermal expansion mismatch. In this study, density functional theory (DFT) simulations were performed to understand the interactions at the GaAs/graphene hetero-interface as well as the growth orientations of GaAs on graphene. To develop a better understanding of the molecular beam epitaxy-grown GaAs films on graphene, samples were characterized by x-ray diffraction (..theta..-2..theta.. scan, ..omega..-scan, grazing incidence XRD and pole figure measurement) and transmission electron microscopy. The realizations of smooth GaAs films with a strong (111) oriented fiber-texture on graphene/silicon using this deposition technique are a milestone towards an eventual demonstration of the epitaxial growth of GaAs on silicon, which is necessary for integrated photonics application.

14 SOLAR ENERGY↗

Multifunctional, Phase-Separated, BaTiO 3 + CoFe 2 O 4 Cap Buffer Layers for Improved Flux-Pinning in YBa 2 Cu 3 O 7- Based Coated Conductors

Phase separated, epitaxial, nanostructured film comprised of BaTiO{sub 3} (BTO) and CoFe{sub 2}O{sub 4} (CFO) composite has been developed as a potential multifunctional cap buffer layer for improved flux-pinning in YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO) films. All films were deposited by pulsed laser deposition on SrTiO{sub 3} (STO) (100) single crystal substrates. The CFO fraction and growth temperature were identified as key factors for determining the areal number density and mean diameter of the CFO nanocolumns. Compared to the reference sample grown on a pure BTO cap layer, the YBCO films grown on BTO+CFO cap layers show a remarkable improvement in isotropic flux-pinning and, consequently, J{sub c} over the entire field and angle ranges. Transmission electron microscopy analysis confirmed the presence of a very defective YBCO layer containing a high density of randomly distributed defects at the interface area, induced by nanostructural modulation on the surface of the BTO+CFO composite cap layer.

36 MATERIALS SCIENCE↗

CdS and Cd-Free Buffer Layers on Solution Phase Grown Cu2ZnSn(SxSe1- x)4 :Band Alignments and Electronic Structure Determined with Femtosecond Ultraviolet Photoemission Spectroscopy

The heterojunctions formed between solution phase grown Cu2ZnSn(SxSe1- x)4(CZTS,Se) and a number of important buffer materials including CdS, ZnS, ZnO, and In2S3, were studied using femtosecond ultraviolet photoemission spectroscopy (fs-UPS) and photovoltage spectroscopy. With this approach we extract the magnitude and direction of the CZTS,Se band bending, locate the Fermi level within the band gaps of absorber and buffer and measure the absorber/buffer band offsets under flatband conditions. We will also discuss two-color pump/probe experiments in which the band bending in the buffer layer can be independently determined. Finally, studies of the bare CZTS,Se surface will be discussed including our observation of mid-gap Fermi level pinning and its relation to Voc limitations and bulk defects.

Haight, Richard↗