Search NASA⌕ Search

SEARCH · Search NASA

Results for “bulk fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Simulating the Effects of Carbon Nanotube Continuity and Interfacial Bonding on Composite Strength and Stiffness

Molecular dynamics simulations of carbon nanotube (CNT) composites, in which the CNTs are continuous across the periodic boundary, overestimate the experimentally measured mechanical properties of CNT composites along the fiber direction. Since the CNTs in these composites are much shorter than the composite dimensions, load must be transferred either directly between CNTs or through the matrix, a mechanism that is absent in simulations of effectively continuous CNTs. In this study, the elastic and fracture properties of high volume fraction discontinuous carbon nanotube/amorphous carbon composite systems were compared to those of otherwise equivalent continuous CNT composites using ReaxFF reactive molecular dynamics simulations. These simulations were used to show how the number of nanotube-matrix interfacial covalent bonds affect composite mechanical properties. Furthermore, the mechanical impact of interfacial bonding was decomposed to reveal its effect on the properties of the CNTs, the interfacial layer of matrix, and the bulk matrix. For the composites with continuous reinforcement, it was found that any degree of interfacial bonding has a negative impact on axial tensile strength and stiffness. This is due to disruption of the structure of the CNTs and interfacial matrix layer by the interfacial bonds. For the discontinuous composites, the modulus was maximized between 4%-7% interfacial bonding and the strength continues to increase up to the highest levels of interfacial bonding studied. Areas of low stress and voids were observed in the simulated discontinuous composites at the ends of the tubes, from which fracture was observed to initiate. Experimental carbon nanotube yarn composites were fabricated and tested. The results were used to illustrate knockdown factors relative to the mechanical performance of the tubes themselves.

Benjamin D Jensen↗
NASA NTRS1975

Rate and time dependent failure of structural adhesives

Studies on two adhesives (Metlbond 1113 and 1113-2) identified as having important applications in the bonding of composite materials are presented. A testing program to ascertain stress-strain, strain-rate, time, yield, and/or failure behavior of these materials in bulk form using uniaxial tensile constant strain-rate, creep, and relaxation tests is described. The stress-strain behavior of each material is shown to be significantly rate dependent. A rate dependent stress whitening (crazing) phenomenon occurs prior to either yield or fracture. A region of linear elasticity, a region of viscoelasticity, and the onset of yielding are identified in the stress-strain behavior. The linear elastic limit and the yield point are shown to be rate dependent and agree well with an empirical equation proposed by Ludwik. A creep to failure phenomenon is shown to exist and is correlated with a delayed yield equation proposed by Crochet. Analytical predictions based on a modified Bingham model are shown to agree well with experimental stress-strain strain-rate data. Analytical predictions based on a modified Ramberg-Osgood equation are also shown for comparison purposes.

Brinson, H. F.↗
NASA NTRS1988

The constitutive representation of high-temperature creep damage

The elastic-viscoplastic constitutive equations of Bodner-Partom were applied to modeling creep damage in a high temperature Ni-alloy, B1900 + Hf. Both tertiary creep in bulk materials and creep crack growth in flawed materials were considered. In the latter case, the energy rate line integral was used for characterizing the crack driving force, and the rate of crack extension was computed using a local damage formulation that assumed fracture was controlled by cavitation occurring within the crack-tip process zone. The results of this investigation were used to assess the evolution equation for isotropic damage utilized in the Bodner-Partom constitutive equations.

Chan, K. S.↗
NASA NTRS2001

Delayed Alumina Scale Spallation on Rene'n5+y: Moisture Effects and Acoustic Emission

The single crystal superalloy Rene'N5 (with or without Y-doping and hydrogen annealing) was cyclically oxidized at 1150 C for 1000 hours. After considerable scale growth (>= 500 hours), even the adherent alumina scales formed on Y-doped samples exhibited delayed interfacial spallation during subsequent water immersion tests, performed up to one year after oxidation. Spallation was characterized by weight loss, the amount of spalled area, and acoustic emission response. Hydrogen annealing (prior to oxidation) reduced spallation both before and after immersion, but without measurably reducing the bulk sulfur content of the Y-doped alloys. The duration and frequency of sequential, co-located acoustic emission events implied an interfacial crack growth rate at least 10(exp -3) m/s, but possibly higher than 10(exp 2) m/s. This is much greater than classic moisture-assisted slow crack growth rates in bulk alumina (10(exp -6) to 10(exp -3) m/s), which may still have occurred undetected by acoustic emission. An alternative failure sequence is proposed: an incubation process for preferential moisture ingress leads to a local decrease in interfacial toughness, thus allowing fast fracture driven by stored strain energy.

Smialek, James L.↗
NASA NTRS2014

Properties of Desert Sand and CMAS Glass

As-received desert sand from a Middle East country has been characterized for its phase composition and thermal stability. X-ray diffraction analysis showed the presence of quartz (SiO2), calcite (CaCO3), gypsum (CaSO4.2H2O), and NaAlSi3O8 phases in as-received desert sand and showed weight loss of approx. 35 percent due to decomposition of CaCO3 and CaSO4.2H2O when heated to 1400 C. A batch of as-received desert sand was melted into calcium magnesium aluminosilicate (CMAS) glass at approx. 1500 C. From inductively coupled plasma-atomic emission spectrometry, chemical composition of the CMAS glass was analyzed to be 27.8CaO-4MgO-5Al2O3-61.6SiO2-0.6Fe2O3-1K2O (mole percent). Various physical, thermal and mechanical properties of the glass have been evaluated. Bulk density of CMAS glass was 2.69 g/cc, Young's modulus 92 GPa, Shear modulus 36 GPa, Poisson's ratio 0.28, dilatometric glass transition temperature (T (sub g)) 706 C, softening point (T (sub d)) 764 C, Vickers microhardness 6.3 +/- 0.4 GPa, indentation fracture toughness 0.75 +/- 0.15 MPa.m (sup 1/2), and coefficient of thermal expansion (CTE) 9.8 x 10 (exp -6)/degC in the temperature range 25 to 700 C. Temperature dependence of viscosity has also been estimated from various reference points of the CMAS glass using the Vogel-Fulcher-Tamman (VFT) equation. The glass remained amorphous after heat treating at 850 C for 10 hr but crystallized into CaSiO3 and Ca-Mg-Al silicate phases at 900 C or higher temperatures. Crystallization kinetics of the CMAS glass has also been investigated by differential thermal analysis (DTA). Activation energies for the crystallization of two different phases in the glass were calculated to be 403 and 483 kJ/mol, respectively.

Desert sand↗
DOE OSTI2022

Impact of Acid–Base Stimulation Sequence on Mineral Stability for Tight/Impermeable Unconventional Carbonate-Rich Rocks: A Delaware Basin Case Study

We report mineral precipitation due to reactions with injected fluids during unconventional fracture stimulation is a well-recognized problem. The goal of this study is to evaluate secondary mineral precipitation and permeability attenuation under chemical injection scenarios specific to the Delaware basin. Whole cylindrical cores (2.54 cm diameter and 2.54 cm height) and ground shale (150–250 μm) from the carbonate-rich Bone Spring Formation, Delaware Basin TX (Leonardian), were reacted at 80 °C and 85 bar using a hydraulic fracturing fluid (HFF) recipe and an injection sequence typical of the Delaware Basin. The reacted shales and solutions were analyzed using a variety of laboratory- and synchrotron-based techniques to characterize both the chemical and spatial distributions of secondary mineral precipitation and identify changes in permeability and mineralogy. This carbonate-rich shale (>84% calcite) rapidly neutralized the acidic HFF. Synchrotron-based X-ray fluorescence mapping coupled with X-ray absorption spectroscopy (both bulk and micro) showed that most of the iron was in an oxidized form prior to exposure to HFF and that almost all iron(II) became fully oxidized after the reaction. Scanning electron microscopy images of the ground shale samples primarily identified iron(oxyhydr)oxide microcrystals on grain surfaces. A few small isolated iron-rich areas also contained sulfur, suggesting that some pyrite was preserved when isolated within a calcite crystal but that most was oxidized. The rapid neutralization of the acid spearhead in these carbonate-rich samples demonstrates that the acid spearhead is useful for initiating fractures in extremely calcite-rich rocks but does little to enhance rock permeability. This suggests that the impact of the acid spearhead is significantly smaller for carbonate-rich shales compared to clay-rich shales, which has broad implications for acidizing in carbonate-rich shale formations and iron transformations within these shales.

58 GEOSCIENCES↗
NASA NTRS1989

Ultrasonic imaging of textured alumina

Ultrasonic images representing the bulk attenuation and velocity of a set of alumina samples were obtained by a pulse-echo contact scanning technique. The samples were taken from larger bodies that were chemically similar but were processed by extrusion or isostatic processing. The crack growth resistance and fracture toughness of the larger bodies were found to vary with processing method and test orientation. The results presented here demonstrate that differences in texture that contribute to variations in structural performance can be revealed by analytic ultrasonic techniques.

Stang, David B.↗
NASA NTRS1990

Ultrasonic imaging of textured alumina

Ultrasonic images representing the bulk attenuation and velocity of a set of alumina samples were obtained by a pulse-echo contact scanning technique. The samples were taken from larger bodies that were chemically similar but were processed by extrusion or isostatic processing. The crack growth resistance and fracture toughness of the larger bodies were found to vary with processing method and test orientation. The results presented here demonstrate that differences in texture that contribute to variations in structural performance can be revealed by analytic ultrasonic techniques.

Stang, D. B.↗
NASA NTRS2013

Covalent Crosslinking of Carbon Nanotube Materials for Improved Tensile Strength

Carbon nanotubes have attracted much interest in recent years due to their exceptional mechanical properties. Currently, the tensile properties of bulk carbon nanotube-based materials (yarns, sheets, etc.) fall far short of those of the individual nanotube elements. The premature failure in these materials under tensile load has been attributed to inter-tube sliding, which requires far less force than that needed to fracture individual nanotubes.1,2 In order for nanotube materials to achieve their full potential, methods are needed to restrict this tube-tube shear and increase inter-tube forces.Our group is examining covalent crosslinking between the nanotubes as a means to increase the tensile properties of carbon nanotube materials. We are working with multi-walled carbon nanotube (MWCNT) sheet and yarn materials obtained from commercial sources. Several routes to functionalize the nanotubes have been examined including nitrene, aryl diazonium, and epoxide chemistries. The functional nanotubes were crosslinked through small molecule or polymeric bridges. Additionally, electron beam irradiation induced crosslinking of the non-functional and functional nanotube materials was conducted. For example, a nanotube sheet material containing approximately 3.5 mol amine functional groups exhibited a tensile strength of 75 MPa and a tensile modulus of 1.16 GPa, compared to 49 MPa and 0.57 GPa, respectively, for the as-received material. Electron beam irradiation (2.2x 1017 ecm2) of the same amine-functional sheet material further increased the tensile strength to 120 MPa and the modulus to 2.61 GPa. This represents approximately a 150 increase in tensile strength and a 360 increase in tensile modulus over the as-received material with only a 25 increase in material mass. Once we have optimized the nanotube crosslinking methods, the performance of these materials in polymer matrix composites will be evaluated.

polymer matrix composites↗
DOE OSTI2020

Polymer-cement composites with adhesion and re-adhesion (healing) to casing capability for geothermal wellbore applications

Deterioration of cement/casing adhesion in wellbore scenarios can result in unwanted and potentially harmful leakage with the potential of serious repair costs. In this work, we explore the use of self-healing polymers added to conventional wellbore cements as a way to bring about self-healing and readhering (to steel casing) properties to the composite material. The polymers are pH resistant and seem to improve the cement integrity after exposure to typical chemical and thermal stresses encountered under geothermal wellbore conditions. We find that addition of about 10-15 wt% of polymer to the cement visually increases its resistance to fracturing from exposure to geothermal conditions, while the adhesive strength of cement/stainless steel increases with curing time for a period of about 10 days. Self-healing capability was demonstrated by permeability analysis showing that polymer-cement composites reduce flow by 50-70% at cement bulk and at the cement/steel interface. Use of atomistic simulations imply that these polymers have good wetting properties on the steel surfaces. Analysis of the interactions between steel/polymer and cement/polymer show that they are complementary, resulting in a wider range of bonding patterns. Cracks are likely to expose under-coordinated sites that result in more bonding interactions, which agrees well with the permeability measurements showing high degree of healed cracks and healed (cement-steel) interfacial gaps together with an overall increased in structural integrity of these advanced polymer-cement composite materials.

Rod, Kenton A.↗
NASA NTRS1994

Computational predictive methods for fracture and fatigue

The damage-tolerant design philosophy as used by aircraft industries enables aircraft components and aircraft structures to operate safely with minor damage, small cracks, and flaws. Maintenance and inspection procedures insure that damages developed during service remain below design values. When damage is found, repairs or design modifications are implemented and flight is resumed. Design and redesign guidelines, such as military specifications MIL-A-83444, have successfully reduced the incidence of damage and cracks. However, fatigue cracks continue to appear in aircraft well before the design life has expired. The F16 airplane, for instance, developed small cracks in the engine mount, wing support, bulk heads, the fuselage upper skin, the fuel shelf joints, and along the upper wings. Some cracks were found after 600 hours of the 8000 hour design service life and design modifications were required. Tests on the F16 plane showed that the design loading conditions were close to the predicted loading conditions. Improvements to analytic methods for predicting fatigue crack growth adjacent to holes, when multiple damage sites are present, and in corrosive environments would result in more cost-effective designs, fewer repairs, and fewer redesigns. The overall objective of the research described in this paper is to develop, verify, and extend the computational efficiency of analysis procedures necessary for damage tolerant design. This paper describes an elastic/plastic fracture method and an associated fatigue analysis method for damage tolerant design. Both methods are unique in that material parameters such as fracture toughness, R-curve data, and fatigue constants are not required. The methods are implemented with a general-purpose finite element package. Several proof-of-concept examples are given. With further development, the methods could be extended for analysis of multi-site damage, creep-fatigue, and corrosion fatigue problems.

Cordes, J.↗
NASA NTRS1959

Factors Affecting the Plasticity of Sodium Chloride, Lithium Fluoride, and Magnesium Oxide Single Crystals

A study was made of the relative magnitude of the effects of various factors on the ductility of single crystals of sodium chloride (NaCl), lithium fluoride (LiF), and magnesium oxide (MgO). Specimen treatments included water-polishing, varying cleavage rate, annealing, quenching, X-irradiation, surface coating, aging, and combinations of some of these treatments. The mechanical behavior of the crystals was studied in flexure and in compression, the latter study being performed at both constant strain rate and constant load. Etch-pit studies were carried out to provide some pertinent information on the results of pretreatment on the dislocation concentration and distribution in the vicinity of the surface. The load deformation curves for these ionic single crystals show an initial region of very low slope which proved to be due to anelastic deformation. The extent of initial anelastic deformation is modified by specimen pretreatment in a way that suggests that this deformation is the result of expansion of cleaved-in dislocation loops, which can contract on the removal of the stress. The effects of the various pretreatments on the load and deflection at fracture are in accord with the prediction one might make with regard to their effect on the nucleation of fatal surface cracks. For NaCl, increases in ductility are always accompanied by increases in strength. The creep constants for NaCl are a function of treatments which affect the bulk structure but are not a function of treatments which only affect the surface.

Stearns, Carl A.↗
NASA NTRS1982

Strength advantages of chemically polished boron fibers before and after reaction with aluminum

In order to determine their strength potential, the fracture properties of different types of commercial boron fibers were measured before and after application of secondary strengthening treatments. The principal treatments employed were a slight chemical polish, which removed low strength surface flaws, and a heat treatment in oxygen, which contracted the fibers and thereby compressed intrinsic bulk flaws. Those fiber types most significantly strengthened were 200 to 400 micrometers (8 to 16 mil) diameter boron on tungsten fibers produced in a single chemical vapor deposition reactor. The slight polish increased average tensile strenghts from 3.4 to 4.4 CN/m2 (500 to 640 ksi) and reduced coefficients of variation from about 15 to 3 percent. The oxygen heat treatment plus slight polish further improved average strengths to 5.5 GN/m2 (800 ksi) with coefficients near 3 percent. To ascertain whether these excellent properties could be retained after fabrication of B/Al composites, as produced and polished 203 micrometers (8 mil) fibers were thinly coated with aluminum, heat treated at B/Al fabrication temperatures, and then tested in tension and flexure at room temperature. The pre-polished fibers were observed to retain their superior strengths to higher temperatures than the as-produced fibers even though both were subjected to the same detrimental reaction with aluminum.

Dicarlo, J. A.↗
DOE OSTI2024

Investigation of acoustic waves under subsurface conditions to improve the predictions of rock mechanical properties and natural fracture characteristics

Mechanical properties and natural fracture characteristics are critical to investigate for subsurface engineering applications, including carbon storage, well drilling, and stimulation, as they govern rock stability, fluid flow, and mechanical behavior under stress. This dissertation integrates experimental and machine learning approaches to enhance the prediction and understanding of these properties by analyzing acoustic wave behavior under varied subsurface conditions. First, the influence of temperature, pore pressure, and supercritical CO2 (scCO2) saturation on poroelastic properties is examined using Gray Berea sandstone samples. The results show that temperature and pore pressure significantly affect the bulk modulus and Biot’s coefficient, while scCO2 saturation impacts rock compressibility, informing strategies for effective geological carbon storage. The study extends this understanding by experimentally evaluating the impact of reservoir depletion on the dynamic mechanical properties of the emerging Caney shale in South Oklahoma with the employment of unsupervised machine learning to predict static mechanical properties across the Caney shale. Integrating petrophysical data and chemostratigraphy, the workflow—featuring K-means clustering, principal component analysis (PCA), and inverse distance weighting (IDW)—improves stratigraphic characterization and the estimation of static-to-dynamic modulus ratios, which is vital for optimizing drilling and stimulation strategies. Finally, the work explores how natural fracture characteristics in shale influence acoustic waveforms and shear wave splitting (SWS) analysis. Experimental data on fractured samples under different stress and temperature conditions, combined with machine learning models such as K-nearest neighbors (KNN) and extreme gradient boosting (XGBoost), reveal key fracture properties impacting SWS and wave propagation. Together, these studies provide a comprehensive framework for linking acoustic wave behavior with rock properties, advancing the methods for monitoring and predicting geomechanical changes. The insights offered valuable implications for safer, more efficient CO2 injection, hydrocarbon extraction, and subsurface management.

Elkholy, Sherif↗
DOE OSTI2020

Fundamental Understanding of Methane-Carbon Dioxide-Water (CH 4 -CO 2 - H 2 O) Interactions in Shale Nanopores under Reservoir Conditions (Quarterly Report)

Shale is characterized by the predominant presence of nanometer-scale (1-100 nm) pores. The behavior of fluids in those pores directly controls shale gas storage and release in shale matrix and ultimately the wellbore production in unconventional reservoirs. Recently, it has been recognized that a fluid confined in nanopores can behave dramatically differently from the corresponding bulk phase due to nanopore confinement. CO 2 and H 2 O, either preexisting or introduced, are two major components that coexist with shale gas (predominately CH 4 ) during hydrofracturing and gas extraction. Note that liquid or supercritical CO 2 has been suggested as an alternative fluid for subsurface fracturing such that CO 2 enhanced gas recovery can also serve as a CO 2 sequestration process. Limited data indicate that CO 2 may preferentially adsorb in nanopores (particularly those in kerogen) and therefore displace CH 4 in shale. Similarly, the presence of water moisture seems able to displace or trap CH 4 in shale matrix. Therefore, fundamental understanding of CH 4 -CO 2 -H 2 O behavior and their interactions in shale nanopores is of great importance for gas production and the related CO 2 sequestration. This project focuses on the systematic study of CH 4 -CO 2 -H 2 O interactions in shale nanopores under high-pressure and high temperature reservoir conditions. The proposed work will help develop new stimulation strategies to enable efficient resource recovery from fewer and less environmentally impactful wells.

04 OIL SHALES AND TAR SANDS↗
NASA NTRS1981

Evaluation of proof testing as a means of assuring mission success for the Space Shuttle thermal protection system

The reliability analysis of a thermal protection system (TPS) incorporating low density, fibrous ceramic materials must take into account the time-dependency and variability of the system's strength. Fracture mechanics concepts can be used to estimate the allowable strength and expected lifetime, as well as to define a proof test scheme for assuring mission success of TPS. The aim of this study was to evaluate the proof testing scheme used on the TPS of the Space Shuttle with these fracture mechanics concepts. The analysis confirmed that proof testing was necessary for the undensified system and that proof testing should lead to adequate reliability with respect to the design stresses. For the undensified system, fracture mechanics predictions were confirmed by measuring the strength of samples that survived proof testing. It was also found that the time-dependent nature of the system's strength was controlled mainly by the ceramic and that this time-strength dependency is similar to that observed for bulk glasses that have compositions similar to the glass fibers present in the ceramic tiles.

Green, D. J.↗
NASA NTRS1990

Chaotic motion of Europa and Ganymede and the Ganymede-Callisto dichotomy

Europa and Ganymede may have undergone an episode of chaotic motion before the establishment of the current Laplace resonance involving the three inner GAlilean satellites. During this episode, the orbital eccentricities of both satellites may have increased dramatically. As a result, the mechanical stresses due to tidal deformation of the satellites' icy lithospheres may have been large enough to result in extensive fracturing, and tidal heating may have melted water ice in the mantles of both satellites, triggering the geological activity that has modified their surfaces since the heavy cratering period. The tidal effects on Ganymede during this episode provide an explanation of the dichotomy between it and Callisto, which have similar bulk properties but very different geological histories.

Tittemore, William C.↗
DOE OSTI2024

Damage evolution and ductile fracture of commercially-pure titanium sheets subjected to simple tension and cyclic bending under tension

This paper describes a study into the evolution of damage in commercial-purity titanium (CP–Ti) sheets subjected to cyclic bending under tension (CBT) and uniaxial tension (simple tension, ST). Sections were taken from sheets that were strained to various levels under both methods and were imaged using X-ray computed tomography (XCT) to reveal insights into the size, density, and distribution of microvoids in the sheets. Digital image correlation (DIC) was also used to observe the surface strain of CBT and ST sheets during testing. These results showed that elongation to failure (ETF) for CBT deformation is about 2.5× higher than for ST, local longitudinal strains in the bulk of the CBT sample are around 1.3× higher than the peak strain in the ST necked region, and 1.7× higher in the localized region of CBT failure. It was found that the volume-density of voids in both sheets followed a similar exponential increase with strain, reaching nearly 45× higher in the CBT than the ST sheets before the onset of failure, mainly due to the higher strain levels achieved. A higher volume density of voids developed in the center of sheets at high levels of strain, for both processes, with the density in the sheet center becoming approximately double that found near the edges. Scanning electron microscopy (SEM) was used to examine the fracture surface of CBT and ST sheets after failure. The observations are presented and discussed highlighting the CBT process as effective to delay ductile fracture of the CP-Ti sheets.

Commercially pure titanium↗