Search NASA⌕ Search

SEARCH · Search NASA

Results for “carbon engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Gas diffusion electrodes, reactor designs and key metrics of low-temperature CO 2 electrolysers

We report that CO 2 emissions can be recycled via low-temperature CO 2 electrolysis to generate products such as carbon monoxide, ethanol, ethylene, acetic acid, formic acid and propanol. In recent years, progress has been made towards an industrially relevant performance by leveraging the development of gas diffusion electrodes (GDEs), which enhance the mass transport of reactant gases (for example, CO 2 ) to the active electrocatalyst. Innovations in GDE design have thus set new benchmarks for CO 2 conversion activity. In this Review, we discuss GDE-based CO 2 electrolysers, in terms of reactor designs, GDE composition and failure modes, to identify the key advances and remaining shortfalls of the technology. This is combined with an overview of the partial current densities, efficiencies and stabilities currently achieved and an outlook on how phenomena such as carbonate formation could influence the future direction of the field. Our aim is to capture insights that can accelerate the development of industrially relevant CO 2 electrolysers.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

How equation of state selection impacts accuracy near the critical point: Forced convection supercritical CO 2 flow over a cylinder

Increasing application of supercritical fluids leads to increased use of numerical simulations to guide designs. However, the impact of Equations of State (EoS) selection on computational cost and accuracy is not well understood. Laminar flow around a heated cylinder is used as a test case. A robust matrix of 99-simulations is used to analyze the flow of carbon dioxide just above the critical point at the isobaric condition of 8 MPa and temperatures between 305 and 390 K. Four EoS were studied: Ideal Gas Law, cubic EoS’s Peng-Robinson and Soave-Redlich-Kwong, and the Span-Wagner EoS. Results were identical for isothermal cases, but for heated or cooled cases, the high-fidelity Span-Wagner EoS simulations presented drastically different wake structures. Compared to the high-fidelity SW EoS, cEoS’s underestimated Nu values by up to 38% and cEoS’s underestimated CD values by 18–42%. In conclusion, the Span-Wagner EoS required only 17% more computation time then the cubic EoS simulations, making the Span-Wagner EoS recommended for engineering design.

42 ENGINEERING↗
DOE OSTI2025

Comparative Technoeconomic Analysis and Life Cycle Assessment of Emerging Reactive Carbon Capture-to-Methanol Pathways

Our group recently developed dual-function materials (DFMs) and reactive carbon capture (RCC) processes for the selective production of methanol (MeOH) or CO, offering two novel and unique pathways for MeOH production. This study conducted a comparative techno-economic analysis (TEA) of the two RCC pathways from exhaust CO 2 : 1) a “Direct RCC-to-MeOH” pathway and 2) an “Indirect RCC-to-CO” pathway followed by MeOH synthesis. The “Direct RCC-to-MeOH” pathway produced a lower levelized cost of MeOH (LCOM) at $\$$0.78/kg, compared to $\$$0.84/kg for the “Indirect RCC-to-CO” pathway. The key difference is the need to recompress the syngas from RCC before MeOH synthesis in “Indirect RCC-to-CO.” Nonetheless, with reduced catalyst costs and hydrogen requirements for “RCC-to-CO,” this pathway merits further study to produce syngas rather than MeOH. Both pathways are comparable in LCOM to baseline e-MeOH production from CO 2 hydrogenation ($\$$0.72/kg) while having lower carbon intensities (0.45 and 0.51 kg-CO 2 e/kg vs 0.54 kg-CO 2 e/kg).

08 HYDROGEN↗
DOE OSTI2023

Fulcrum House – Towards a Sustainable Composite Architecture

In the last decades, the accessibility to digital fabrication technologies positioned composites as an affordable, structurally efficient and low-maintenance alternative to traditional mineral-based and high-energy materials. Of special interest are carbon nanotubes (CNT) and carbon foam (CFoam) from methane and coal pyrolysis respectively, as an environmentally friendly substitute to glass and carbon fiber. This paper presents the design of a principled single-family house, as a first case study to identify the constraints of such a material system, including technology gap, techno-economic and life cycle assessment, as well as building code requirements. In turn, the investigation proposes a suitable design-to-fabrication workflow, which potentially could bring CNT and CFoam materials to the construction of buildings.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Effect of hollow fiber membrane packing on the performance of modules formed with fiber tows

Membrane processes are the preferred option for many gas separations. Hollow fiber membranes are commonly used in these processes. Commercial hollow fiber membrane modules are often fabricated from small groups of fibers (i.e., a tow) that are arranged into a larger cylindrical bundle. The existence of fiber tows can lead to packing non-uniformity. This nonuniformity can result in nonideal fluid distribution in the shell and be detrimental to module performance. In this work, full three-dimensional models of flow and mass transfer within fiber bundles formed from tows have been developed. These models account for the detailed fiber arrangement within modules and are solved to evaluate module separation performance in terms of stage cut and required membrane area as a function product gas purity for carbon capture applications. Results are presented illustrating the effects of varying fiber packing arrangements within a tow and varying tow packing arrangements. Further, the results suggest smaller tows are preferred over larger tows, at fixed overall fiber packing and lower intra- and inter-tow packings are preferred. To reduce the computational cost of simulating large fiber bundles, the use of an equivalent planar bundle is proposed (EPB). A simple procedure for determining the geometry of the EPB is described and validated through comparisons of calculated performance metrics with results obtained from full three-dimensional simulations.

42 ENGINEERING↗
DOE OSTI2021

Substitution of virgin carbon fiber with low-cost recycled fiber in automotive grade injection molding polyamide 66 for equivalent composite mechanical performance with improved sustainability

Recycled carbon fiber has historically proven challenging to integrate into composite manufacturing due in no small part to the low-density, randomly oriented, discontinuous fiber format that results from typical recycling. Discontinuous fiber requires the use of alternative technologies than those traditionally applied to continuous fiber (e.g., hand lay-up, winding). Extrusion compounding is one such applicable technology, but material transfer into the system requires alternative feeding equipment or the use of an altered procedure as trialed in this research. In this study, an injection molding compound for automotive applications was prepared with recycled carbon fiber and compared against an existing commercial compound. Input fibers and molded compound were evaluated for mechanical performance, while relevant variables such as compounded fiber alignment and aspect ratio were compared to the existing baseline material to confirm a like-for-like composite material structure. Overall, analysis indicates that recycled fiber performs similarly to virgin fiber reinforcement, demonstrating that recycled fiber may be a viable drop-in replacement for short-fiber discontinuous applications.

42 ENGINEERING↗
DOE OSTI2021

Controlled Pyrolysis: A Robust Scalable Composite Recycling Technology

The reinforced composites industry is facing significant challenges in handling the scrap composite material from automobile manufacturing, the wind turbine industry, and others. The fibers in the material, whether they be carbon, glass, or other materials have commercial value if they can be recovered successfully. Successfully means the fibers are clean with no sizing or other binders and have adequate strength and physical properties that would allow them to be economically reprocessed into valuable product. The composites recycling project was an industry-collaborative effort to develop a composite recycling technology using controlled pyrolysis. Through the recycling of scrap and end-of-life (EOL) cured composite materials, this pilot study was intended to create a business case by realizing a cost-effective means for recycling EOL and production scrap composite materials, ultimately reducing the volume of composite materials destined for landfill. The project was led by the Institute for Advanced Composites Manufacturing Innovation (IACMI), the American Composites Manufacturers Association (ACMA), Oak Ridge National Laboratory (ORNL), Continental Structural Plastics (CSP) a Teijin Group Company, CHZ Technologies, and A. Schulman with support from Owens Corning, John Deere, General Electric (GE), Ashland LLC, and Plastics Europe (CEFIC). The team studied and tested CHZ Technologies’ controlled pyrolysis system, known as the Thermolyzer TM , which operates on a scalable basis to convert organic polymer materials into a clean synthesis gas and char containing the recoverable carbon and glass fiber reinforcement. The recoverable energy contained in the input polymers creates the synthesis gas that can be used to provide heat to the Thermolyzer TM primary reactor in a sustainable manner. That is, once the Thermolyzer TM is started with a small amount of external natural gas, the synthesis gas that is created from the polymers will continue to operate the burners so long as feedstock is supplied. The reinforcing fiber materials remaining in the solid phase char were separated and cleaned for re-use in other polymer systems based on the retained properties of the fibers. The study created reports (attached in the appendix) on the Mass and Energy Balances, syngas analytics, VOC assessment, yield analysis and other analytics necessary for a Techno-Economic Analysis (TEA) to quantify the economic impact of the recovery and sustainable re-use of the carbon and glass fibers. The process consisted of 4 steps: Selection of 4 samples of cured composite waste materials from project partners interested in materials recycling and recovering the reinforcing fibers for best case re-use. The materials included glass fiber (GF) polyester/vinyl ester automotive SMC from CSP, GF epoxy balsa/PVC foam wind blades from GE, carbon fiber (CF) epoxy wind blade laminated spar caps from GE, and GF/CF epoxy hybrid assembly from John Deere. Processing the waste composite samples into 1-2” shreds. Packaging the shredded composites into bulk sacks on international shipping pallets for shipment to KUG in Forst (Lausitz), Germany. Pyrolysis of the shredded composites under controlled conditions designed for each polymer system. Collecting samples of the gas and char for analysis. Shipping the char containing the CF/GF back to the US for the next steps of testing the fibers and developing protocols for sustainable re-use of the fibers in composite applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Upcycling of CFRP Waste: Viable Eco-friendly Chemical Recycling and Manufacturing of Novel Repairable and Recyclable Composites

The rapid growth of the carbon fiber-reinforced polymer (CFRP) composite market has driven researchers to find value-added applications for outdated prepregs, manufacturing scraps, and end-of-life components. Currently, most CFRP waste is incinerated or landfilled, which squanders its residual value and burdens the environment. Various mechanical, thermal, and chemical approaches have been attempted to recover the carbon fiber, polymer matrix, or both. However, these current practices are often costly, energy-intensive, and generate secondary waste and pollution. To address these shortcomings, this project aims to develop a viable and sustainable chemical recycling technology for CFRP waste that can efficiently and cost-effectively decompose the polymer matrix and manufacture new recyclable composites from both the recovered carbon fiber (rCF) and decomposed matrix polymer (DMP).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hall effect in gated single-wall carbon nanotube films

The presence of hopping carriers and grain boundaries can sometimes lead to anomalous carrier types and density overestimation in Hall-effect measurements. Previous Hall-effect studies on carbon nanotube films reported unreasonably large carrier densities without independent assessments of the carrier types and densities. Here, we have systematically investigated the validity of Hall-effect results for a series of metallic, semiconducting, and metal–semiconductor-mixed single-wall carbon nanotube films. With carrier densities controlled through applied gate voltages, we were able to observe the Hall effect both in the n- and p-type regions, detecting opposite signs in the Hall coefficient. By comparing the obtained carrier types and densities against values derived from simultaneous field-effect-transistor measurements, we found that, while the Hall carrier types were always correct, the Hall carrier densities were overestimated by up to four orders of magnitude. This significant overestimation indicates that thin films of one-dimensional SWCNTs are quite different from conventional hopping transport systems.

42 ENGINEERING↗
DOE OSTI2023

Techno-economic analysis of carbon dioxide capture from low concentration sources using membranes

Rising carbon dioxide (CO 2 ) levels in the atmosphere lead to global warming, causing climate change. As such, carbon capture has become necessary to slow the increase and reduce CO 2 levels in the atmosphere. Point source emissions have a wide range of CO 2 concentrations, but emissions below 3% CO 2 have mostly been ignored because Carbon capture from these sources has been viewed as costly and economically unsustainable. Membrane technologies are considered the most viable solution by virtue of more energy-efficient operation. Our group at Idaho National Laboratory (INL) has developed poly[bis((2-methoxyethoxy)ethoxy)phosphazene] (MEEP)-based carbon dioxide selective membranes with CO 2 /N 2 selectivity greater than 40 and CO 2 permeability greater than 450 Barrer. To understand the economics of carbon capture, a spreadsheet-based techno-economic analysis (TEA) model was developed to consider multiple parameters, including selectivity and permeability of the membranes, performance conditions such as the number of stages, module material, electricity price, membrane price, and capital financing. The cost of carbon capture in US $\$$/metric ton was calculated at various purities and compared with other membrane processes, cryogenic capture, solvent-based capture, and pressure swing adsorption-based capture. It was determined that a MEEP-based three-stage process had a capture cost of US $\$$ 50.1/metric ton for 99.8% purity CO 2 from a 1% CO 2 feed source in nitrogen (N 2 ). In conclusion, the capture cost using the best performing Pebax-based membrane was 464% higher, cryogenic capture was 60%–140% higher, pressure swing adsorption was 55%–165% higher, and chemical absorption was -10%–110% higher than MEEP-based membrane capture, respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Continuous stabilization of polyacrylonitrile (PAN) - carbon nanotube (CNT) fibers by Joule heating

We report stabilization is one of the important processes used to convert polyacrylonitrile (PAN) fibers into carbon fiber and is usually driven by energy-intensive and time-consuming convective heating. A continuous and energy-efficient alternative is desirable. Here, a continuous Joule heating process has been used for the first time to stabilize PAN fibers containing carbon nanotubes (CNT). Single-component PAN/CNT fibers and bi-component fibers with core-sheath geometry were fabricated through the gel spinning method. Joule heating was conducted continuously on a 200 filament bundle for single-component fibers and on bundles with up to 6000 filaments for the bi-component fibers. A model of heat transfer and thermodynamics occurring during Joule heating is developed and utilized to understand the reductions in stabilization time and energy consumed when compared to convective heating. The minimum energy needed for stabilization through Joule heating is estimated to be less than 1% of the energy used through convective heating.

42 ENGINEERING↗
DOE OSTI2023

Advances in multi-dimensional cellulose-based fluorescent carbon dot composites

Recently, fluorescent materials composed of carbon dots (CDs) have attracted increasing attention in diverse fields, including the environment, food, biology, and medicine. Cellulose has emerged as a promising class of materials for carriers due to its low cost, fascinating biodegradability, and various morphologies, especially in available different dimensions. By taking advantage of the respective superiority of fluorescent materials and cellulose carriers, the performance of fluorescence composite materials can be optimized and their application may be extended. Here, in this review, the study emphasizes the synthesis and applications of cellulose-based fluorescent materials with different dimensions. Moreover, some effective strategies and potential challenges for further development of cellulose-based fluorescent materials are discussed. A deeper understanding will provide a guide for the materials with ideal fluorescent performances.

42 ENGINEERING↗
DOE OSTI2025

Efficient Synthetic Natural Gas Production from Direct Air Capture Using Titania-Based Dual Function Materials

Converting atmospheric CO2 into methane offers a compelling pathway to store intermittent renewable electricity and enhance energy security using existing natural gas infrastructure. However, current CO2 utilization approaches remain energy- and capital-intensive, largely due to the need for separate capture, purification, and conversion steps. Integrating CO2 capture with catalytic methanation represents a transformative strategy for process intensification on both the unit operation and molecular levels. We report a series of Ru-Na/TiO2 dual function materials (DFMs) for a reactive carbon capture (RCC) process consisting of simulated direct air capture and subsequent CO2 methanation (DACM). Superior methane desorption purity was observed on TiO2-based DFMs (>94 %) relative to state-of-the-art Al2O3-supported DFMs (77 %). Modifying the process to begin CO2 adsorption immediately following the methanation stage, rather than beginning adsorption near ambient temperature, resulted in >97 % methane desorption purity, suitable for injection into the natural gas pipeline without additional CO2 separation steps.

organic↗
DOE OSTI2023

4D structural changes and pore network model of biomass during pyrolysis

Biochar is an engineered carbon-rich substance used for soil improvement, environmental management, and other diverse applications. To date, the understanding of how biomass affects biochar microstructure has been limited due to the complexity of analysis involved in tracing the changes in the physical structure of biomass as it undergoes thermochemical conversion. In this study, we used synchrotron x-ray micro-tomography to visualize changes in the internal structure of biochar from diverse feedstock (miscanthus straw pellets, wheat straw pellets, oilseed rape straw pellets, and rice husk) during pyrolysis by collecting a sequence of 3D scans at 50 °C intervals during progressive heating from 50 °C to 800 °C. The results show a strong dependence of biochar porosity on feedstock as well as pyrolysis temperature, with observed porosity in the range of 7.41–60.56%. Our results show that the porosity, total surface area, pore volume, and equivalent diameter of the largest pore increases with increasing pyrolysis temperature up to about 550 °C. The most dramatic development of pore structure occurred in the temperature range of 350–450 °C. This understanding is pivotal for optimizing biochar’s properties for specific applications in soil improvement, environmental management, and beyond. By elucidating the nuanced variations in biochar’s physical characteristics across different production temperatures and feedstocks, this research advances the practical application of biochar, offering significant benefits in agricultural, environmental, and engineering contexts.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A Review of CCUS in the Context of Foams, Regulatory Frameworks and Monitoring

Greenhouse gas emission into the atmosphere is considered the main reason for the rise in Earth’s mean surface temperature. According to the Paris Agreement, to prevent the rise of the global average surface temperature beyond two degrees Celsius, global CO2 emissions must be cut substantially. While a transition to a net-zero emission scenario is envisioned by mid-century, carbon capture, utilization, and storage (CCUS) will play a crucial role in mitigating ongoing greenhouse gas emissions. Injection of CO2 into geological formations is a major pathway to enable large-scale storage. Despite significant recent technological advancements, mass deployment of these technologies still faces several technical and non-technical difficulties. This paper provides an overview of technical milestones reached thus far in CO2 capture, utilization, geological storage, monitoring technologies, and non-technical aspects such as regulatory frameworks and related policies in the US and the rest of the world. This paper describes different injection methods to store CO2 in various subsurface formations, the use of foams and the resulting potential gains in CO2 storage capacity, the role of nanoparticles for foam stabilization, and ensuring long-term storage safety. This work also addresses several safety-related aspects of geological storage and subsurface monitoring technologies that may mitigate risks associated with long-term storage.

42 ENGINEERING↗
DOE OSTI2022

The influence of random packed column parameters on the liquid holdup and interfacial area

Abstract Carbon dioxide capture via solvent absorption in packed columns has emerged as a potential technology to mitigate coal‐fired power plant CO 2 emissions. Parameters, including packing types, solvent properties, and operating conditions, could potentially affect the packed column CO 2 capture efficiency. To understand the importance of those parameters and help packed column optimization, a design of experiments (DoEs) method was proposed to generate input parameter matrix. Combined with multiphase computational fluid dynamics (CFD), the random packed column parameter influence on the liquid holdup and interfacial area can be efficiently investigated. Surrogate‐based sensitivity analysis shows that the solvent flow rate and contact angle are key factors dictating liquid holdup and interfacial area. On the other hand, solvent viscosity has a marginal impact on the interfacial area. The sensitivity scores were calculated for each input parameter to guide the selection of dimensionless numbers for the liquid holdup and interfacial area correlation development.

42 ENGINEERING↗
DOE OSTI2023

Crashworthiness of recycled carbon fiber composite sinusoidal structures at dynamic rates

Fiber reinforced polymer composites are finding applications in the automotive space for structurally critical applications including crash management. The use of recycled carbon fiber reinforcement can greatly reduce carbon emissions. In this study, recycled carbon fiber composites were manufactured into a self-supporting geometry using three matrices: polyphenylene sulfide (PPS), acrylonitrile butadiene styrene (ABS), and a structural epoxy, and subsequently crushed between flat platens at dynamic rates ranging from 4.6 to 9.1 ms -1 at temperatures in a range of -40°C to 80°C. Load-displacement data was used to evaluate their specific energy absorption, crush efficiency, and steady-state crush stress. Further, the energy absorption of the ABS composites was strongly sensitive to temperature, while the PPS composites exhibited strong crush efficiency dependence with both rate and temperature. The epoxy composites exhibited stable crush behavior at dynamic crush rates but exhibited a dramatic reduction in crush efficiency relative to quasi-static tests. The results of this study indicate that recycled fiber composites can achieve very high energy absorption levels (50–80kJkg -1 at room temperature) that make them an excellent alternative to more expensive and less environmentally friendly continuous virgin fiber laminates.

42 ENGINEERING↗
DOE OSTI2023

Carbonic anhydrase textile structured packing for efficient CO 2 absorption in methyldiethanolamine solvent

Carbonic anhydrase (CA) is an attractive biodegradable catalyst for CO 2 absorption in solvent–based CO 2 capture. However, maintaining the stability of CA as a homogeneous component of the solvents is a challenge. Solvent regeneration temperature typically exceeds the enzyme thermal tolerance, which leads to CA deactivation. To reduce the need for frequent CA replenishment and to avoid inactive CA accumulation in the solvent, this work shows the benefits of an immobilization strategy where CA is fixed in a second–generation design of textile structured packing (CATSP–2) modules. The enzyme–immobilized packing showed 1.5 times better performance in CO 2 separation compared with traditional structured packing with a corresponding increased CO 2 loading in the rich solvent. The modules exhibited good CA activity retention of ~80% during the tests without any CA replenishment. As a result, applying CATSP–2 could potentially decrease the packing height and absorber column size for a lower cost per amount of CO 2 captured.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗