Search NASA⌕ Search

SEARCH · Search NASA

Results for “combustion turbines”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Flame Characterization of a Hydrogen Micromix Burner using Experimental and Numerical Methods - Extended Abstract

Micromix combustion presents a promising solution for integrating hydrogen into gas turbine combustors, offering rapid and compact air-fuel mixing that effectively shortens the combustion zone and significantly reduces nitrogen oxides (NOX) emissions. A major challenge in hydrogen combustion systems is flashback, which is mitigated through short mixing lengths and high flow velocities. This study investigates three fuel injector designs – zero swirl, low swirl, and high swirl – for a 6-mm inner diameter nozzle, where hydrogen is injected through six 0.3 mm diameter holes in a jet-in-crossflow configuration relative to the airstream. Numerical simulations indicate stable flame formation, moderate peak flame temperatures, and subsequent low NOx potential for all designs. These injectors have been fabricated using additive manufacturing, and upcoming experiments will explore flame structure and NOx behavior across varying fuel injection angles, equivalence ratios and pre-mixer velocities. These efforts aim to advance the development of low-emission hydrogen micromix combustion.

hydrogen↗
DOE OSTI2023

Cooled Gas Turbine and Combined Cycle Analysis for H 2 -CH 4 Fuel Mixes (Up to 100% H 2 )

In this study, a cooled gas turbine analysis was conducted for varying levels of hydrogen (H 2 ) blends with the natural gas. The ultimate goal is to have a gas turbine design that can be used for all the fuel blends (including 100% H 2 ) without any changes to the system. The technological developments in the cooling system, gas turbine design and materials that will be required for H 2 combustion were identified and analyzed in this study to develop an advanced gas turbine design for H 2 fuels. The study includes a combined cycle performance analysis with the H 2 fuel blends using the advanced gas turbine design developed in this study. A techno-economic analysis was conducted for analyzing the impact of the H 2 fuels on the levelized cost of electricity and cost sensitivities to fuel price and capacity factor.

03 NATURAL GAS↗
DOE OSTI2024

Cooled Gas Turbine and Combined Cycle Analysis for NH 3 -CH 4 Fuel Mixes (Up to 100% NH 3 )

In this study, a cooled gas turbine (GT) analysis was conducted for varying levels of ammonia (NH 3 ) blends with methane. The ultimate goal is to have a gas turbine design that can be used for all the fuel blends (including 100% NH 3 ) without any changes to the system. The technological developments in the cooling system, gas turbine design, and materials that will be required for NH 3 combustion were identified and analyzed in this study to develop an advanced gas turbine design for NH 3 fuels. The study includes a combined cycle performance analysis with the NH 3 fuel blends using the advanced gas turbine design developed in this study. A techno-economic analysis was conducted for analyzing the impact of the NH 3 fuels on the levelized cost of electricity and cost sensitivities to fuel price and capacity factor.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Enclosed Sydney Swirl Burner Experimental Data Set - Release 1.0

This submission includes a comprehensive data set for the NETL Enclosed Sydney Swirl Burner, generated between 2012 and 2014. The data set includes global parametric data and advanced diagnostic data for (3) flames of interest to CFD model validation. The submission includes a companion summary document describing the data and associated references.

Diagnostics↗
DOE OSTI2024

Quantifying Socioeconomic Impacts of Electricity Generating Technologies

The levelized cost of energy (LCOE) and other cost metrics used in energy planning do not account for out-of-market impacts of the technology choice. While a decision-maker at the utility or asset owner level may compare multiple forms of electricity generating technology using LCOE, a decision-maker over energy policy or community stakeholders may be interested in considering impacts beyond those that LCOE measures. This report quantifies economic impacts such as jobs and wage growth across electricity generation technologies then develops an approach to systematically compare socioeconomic metrics across technology choices. To address additional workforce related impacts, this report also compares the typical workforce education requirements and annual income levels for multiple types of electricity generating facilities. The grid scale electricity generating technologies analyzed in this report produce power using conventional hydroelectric dams, coal, natural gas, nuclear reactors, solar PV, land-based wind turbines, geothermal heat, and woody biomass combustion. Although it doesn’t generate electricity itself, the economic impacts associated with battery storage equipment manufacturing and installation were also analyzed.

03 NATURAL GAS↗
DOE OSTI2024

Effect of Pressure on Structure and Extinction of Counterflow Premixed Ammonia/Air Flames

With the growing interest in ammonia as a carbon-free fuel, numerous recent research efforts on fundamental combustion characteristics of ammonia have been reported. Despite this attention, there remain fundamental aspects that lack experimental investigation or validated chemical kinetic models. Specifically, the understanding of ammonia flame structure and the quantification of extinction limits at elevated pressures are incomplete. Furthermore, the chemistry of NOx in relation to ammonia flames has not been thoroughly examined, especially at pressure, and it is useful to explore the operating conditions that exhibit favorable flame stability with minimal NOx formation. In the current work, key characteristics of ammonia/air combustion, including strain-induced extinction limits and NO* chemiluminescence, are experimentally investigated over a wide range of equivalence ratios and pressures. This paper presents initial results in a study directed to improved comprehension of ammonia combustion chemistry, and acquisition of new datasets under elevated pressure and temperature conditions, to better refine rate expressions for important reactions in ammonia combustion.

08 HYDROGEN↗
DOE OSTI2020

Optimization of energy requirements for CO 2 post-combustion capture process through advanced thermal integration

The energy optimization modeling work described here was performed to determine efficiency improvements that could be achieved for existing coal-fired power plants to retrofit a partial CO 2 capture from the post-combustion flue gas for carbon sequestration through thermal integration. The work presented includes optimization of the mono-ethanol amine (MEA)-based post-combustion CO 2 capture to reduce energy requirements that could be achieved at existing power plants by thermal integration of the steam turbine cycle, boiler, CO 2 compression train and post-combustion CO 2 capture process to offset efficiency and capacity losses that would be incurred by retrofit or implementation of post-combustion CO 2 capture. Furthermore, partial CO 2 capture, involving treatment of less than 100% of the flue gas leaving the plant and modular design of the CO 2 scrubbing system, was also investigated. Thermal integration of the steam turbine cycle with boiler and CO 2 compression train improved cycle and plant performance and offset, in part, the negative effects of post-combustion CO 2 capture. The best-analyzed integration options improved gross power output by 5% and net unit efficiency by 1.57%, relative to the conventional MEA process. Operating with 40% CO 2 capture increased gross power output by 11.6–14% (depending on the MEA thermal integration option), relative to the conventional MEA integration and 90% CO 2 capture. The improvement in net unit performance is larger compared to the improvement in turbine cycle performance because of the CO 2 compression work, which is also reduced by partial CO 2 capture.

42 ENGINEERING↗
DOE OSTI2021

Preheating and premixing effects on NO x emissions in a high-pressure axially staged combustor

NO x emissions remain a primary concern for modern and future gas turbines, particularly as we progress towards a net-zero carbon future. It is critical to identify novel strategies to mitigate environmental pollutants for both modern turbines operated on natural gas and future turbines projected to use carbon-free fuels (such as hydrogen). In the current study, NO x emissions of a reacting methane-air jet in a vitiated crossflow are experimentally investigated in a model axially staged combustor at 5 atm. The combustion products from the main stage combustor flow into the axial stage at temperatures ranging from 1580 to 1650 °C. The axial stage contains a reacting jet in crossflow, which provides an overall temperature rise ranging from 50 to 220 °C to generate exit temperatures similar to gas turbine engines. The focus of this paper is to explore the effects of flame liftoff and ignition timescales on the NO x contribution of this secondary jet. This is done by varying the premixed level and preheat temperature of the axial jet. The effects are explored at different momentum flux ratios (J), jet equivalence ratios (φ jet ), exit temperatures (T exit ), and main stage (headend) temperatures (T HE ). High-speed CH* chemiluminescence imaging is employed for each test case to determine the flame stabilization point. For a given temperature rise and combustor exit temperature, an increase in ignition delay was observed with a decrease in jet temperature. This provided a NO x benefit, particularly for jets that are injected at or close to an ignitable mixture fraction. Similarly, the coaxial injector caused a significant ignition delay compared to the fully premixed injector; this also led to a NO x benefit. Overall, the results show that a thermally driven delay in the axial stage provides a greater NO x reduction than a mixing delay.

03 NATURAL GAS↗
DOE OSTI2025

Measurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels

Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.

09 BIOMASS FUELS↗
DOE OSTI2022

Experimental and modeling study of water time histories during H 2 S-N 2 O combustion in a shock tube

Here, with the interest in directly burning sour gas in gas turbines, and the fact that even small amounts of H 2 S or its combustion products can alter combustion characteristics, many research studies have been performed to better understand the combustion chemistry of H 2 S. In the present study, the water formation was followed by laser absorption with N 2 O as an oxidant, instead of O 2 . Nitrous Oxide being essentially consumed via N 2 O (+M) ⇌ N 2 + O (+M), the water formation via the H 2 S + O route can then be probed to further validate the models. Three H 2 S/N 2 O mixtures diluted in 98% Ar were studied to cover the following range of equivalence ratios: 0.5, 1.0, and 2.0, over a wide range of temperatures (1580–1940 K) around atmospheric pressure. A chemical kinetic model was then developed first by validating the base N 2 O kinetics mechanism, then by investigating the experimental results presented herein. The N 2 O kinetics mechanism was updated with recent work on the low- and high-pressure limits for N 2 O decomposition (N 2 O (+M) ⇌ N 2 + O (+M)) as well as a review of rate coefficients for N 2 O + H ⇌ N 2 + OH from the literature. Good agreement is shown for H 2 /N 2 O mixtures. Updates were then made to the H 2 S kinetics mechanism, specifically, an update from the literature on SO 2 + H (+M) ⇌ SO + OH (+M) and an adjustment to SO + SH ⇌ S 2 + OH. Additionally, reactions between SH and N 2 O were determined using W1BD data and transition state theory which required the addition of an NNS sub-mechanism. With these updates, the mechanism provides good agreement with the H 2 S/N 2 O experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Efficient turbine engine using integrated ammonia fuel processing

A gas turbine engine includes a core engine that includes a core flow path where air is compressed in a compressor section, communicated to a combustor section, mixed with an ammonia based fuel and ignited to generate a high energy combusted gas flow that is expanded through a turbine section. The turbine section is mechanically coupled to drive the compressor section. An ammonia flow path communicates an ammonia flow to the combustor section. A cracking device is disposed in the ammonia flow path. The cracking device is configured to decompose the ammonia flow into a fuel flow containing hydrogen (H2). At least one heat exchanger is upstream of the cracking device that provides thermal communication between the ammonia flow and a working fluid flow such that the ammonia fluid flow accepts thermal energy from the working fluid flow.

Smith, Lance L.↗
DOE OSTI2024

Finite Element Modeling of the Phase Change in Thermally-Grown SiO 2 in SiC Systems for Gas Turbines

The operating lifetimes of SiC-based components in combustion environments are directly linked to the adhesion of the protective environmental barrier coating (EBC) layer. One of the major known failure modes for EBCs is the formation of a thick SiO 2 thermally grown oxide (TGO), which decreases coating adhesion and encourages eventual coating spallation. The effect of the TGO thickness under Yb 2 Si 2 O 7 EBCs on silicon carbide was investigated using finite element models (FEMs) with various interfacial architectures and SiO 2 TGO thicknesses. Further, the FEMs incorporated a user-defined material to simulate the volume contraction of the TGO during the silica phase transformation from β-cristobalite to α-cristobalite upon cooling from the stress-free state at 1350°C to room temperature. Systems with and without a silicon bond coating intermediary layer were assessed. It was shown that the TGO phase transformation stress (1.6–1.7 GPa) dominated the increase in stress in the TGO and EBC layers. Furthermore, it was found that stress increase in the TGO was independent of TGO thickness and interface geometry. These results indicate that stabilization of the TGO to mitigate the phase transformation could dramatically improve the performance of SiC-base components with EBCs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydrogen Combustion Research at NETL

Presentation made at the 2022 University Turbine Systems Research (UTSR) and Advanced Turbines Program Review Meeting in San Diego, CA, September 27-29, 2022.

Strakey, Peter↗
DOE OSTI2022

Positive Power with Negative Emission Flexible NGCC Enable by Modular Direct Air Capture (Final Report)

The primary project objective was to synthesize a retrofit design of a natural gas combined cycle plant (Fseries gas turbines in 2x1 configuration) to integrate post-combustion (PCC) and direct air carbon capture (DAC) systems that could produce power with negative emissions across a wide range of loads, see table below. The IP-LP crossover and LP steam system of the NGCC were reconfigured to enable 97% CO2 capture in the PCC system at all loads, and heat integration with the DAC reduced the parasitic load of carbon capture by recovering the heat of condensation of the steam. Similar results were found for Hseries gas turbines.

03 NATURAL GAS↗
DOE OSTI2023

Performance Characteristics of a Rotating Detonation Combustor Exiting Into a Pressurized Plenum to Simulate Gas Turbine Inlet

Abstract The present study aims to experimentally characterize the performance of a rotating detonation combustion (RDC) system integrated with a pressurized downstream plenum to simulate the high-pressure inlet conditions of power-generating gas turbines. A thorough understanding of the operational behavior including wave mode behavior, static pressure profile along the combustor length, and dynamic features of pressure fluctuations is crucial for successful integration of RDC with the turbine. In this study, two RDC configurations are investigated, RDC with a constant area annulus and RDC with a converging nozzle. In both cases, the RDC flow exited into a plenum chamber kept at pressures varying from 155 kPa to 330 kPa. RDC was operated on methane and oxygen-enriched air to represent reactants used in land-based power generation. Experiments were conducted for the two RDCs configurations operated at three reactant mass flow rates (0.23, 0.32, and 0.46 kg/s). The RDC performance is characterized by time-averaged static pressure measurements, and wave velocity determined by ionization probes. In addition, dynamic pressure measurements were recorded both inside and near the exit of RDC channel to investigate wave interactions between RDC and downstream plenum. Results show that the RDC with the converging nozzle achieved superior performance while minimizing detrimental interactions with the reflected shock and/or acoustic waves from the downstream plenum.

Engineering↗
DOE OSTI2024

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗
DOE OSTI2020

DICE-gas turbine compound reheat combined cycle

Coal-fired Direct Injection Carbon Engine – Gas Turbine (DICE-GT) Compound-Reheat Combined Cycle (CRCC), is a combined cycle power plant comprising a multiplicity of coal-fired reciprocating internal combustion engines (RICE), which is commonly referred to by the acronym DICE (Direct Injection Carbon Engine); a natural gas-fired gas turbine (turbine and combustor); a heat recovery steam generator (HRSG); a steam turbine generator; and an integrally geared and intercooled centrifugal air compressor. Finally, the concept uses coal-water slurry/fluid in the DICE and natural gas (or hydrogen) in the gas turbine for unmatched efficiency (well above 50% net LHV) and modularity (block sizes of 120, 240 and 360 MW) with easy adaptability to carbon capture and sequestration with minimal additional cost, complexity and performance hit.

42 ENGINEERING↗