Search NASA⌕ Search

SEARCH · Search NASA

Results for “conical shocks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Computational simulation of flows about hypersonic geometries with sharp leading edges

Hypersonic waverider design has become an important concern in the aerospace industry. As one part of an inverse design effort for waveriders, work has been done to apply existing Euler and Navier-Stokies flow solvers to hypersonic geometries with sharp leading edges. Previously, calculations were done on bodies with rounded leading edges or with conical solutions for the nose initial conditions. In this paper, solutions are computed about waveriders and conical shapes with sharp leading edges without resorting to either shortrcut. All solutions show attached shocks with fully supersonic flows at the nose and along the leading edges. Flows about several waverider shapes are shown, as well as a preliminary cone with inlet calculation to study the shock/inlet interaction.

Jones, Kevin D.↗
NASA NTRS1960

The Blunt Plate In Hypersonic Flow

The sonic-wedge characteristics method has been used to obtain the shock shapes and surface pressure distributions on several blunt two-dimensional shapes in a hypersonic stream for several values of the ratio of specific heats. These shapes include the blunt slab at angle of attack and power profiles of the form yb = a)P, where 0 les than m less than 1, Yb and x are coordinates of the body surface, and a is a constant. These numerical results have been compared with the results of blast-wave theory, and methods of predicting the pressure distributions and shock shapes are proposed in each case. The effects of a free-stream conical-flow gradient on the pressure distribution on a blunt slab in hypersonic flow were investigated by the sonic-wedge characteristics method and were found to be sizable in many cases. Procedures which are satisfactory for reducing pressure data obtained in conical flows with small gradients are presented.

Baradell, Donald L.↗
NASA NTRS1959

The Stabilizing Effectiveness of Conical Flares on Bodies with Conical Noses

An analysis is presented of published results of force tests on 80 cone-cylinder-flare configurations at Mach numbers of 2.18, 2.81, and 4.04. The contributions, excluding interference effects, of the cone-cylinder bodies to the over-all normal force derivatives have been removed by means of the second-order shock-expansion method, and the normal force derivatives at zero angle of attack due to the flares alone are shown. The results from a wide variety of configurations are correlated by plotting ratios of the normal force derivatives of the flares to the normal force derivatives of cones having the same included angle. Comparisons are made of the experimental normal force results with the normal force derivatives obtained by assuming conical flow over the flares and with those obtained by use of the second-order shock-expansion method. The comparisons show that use of the second-order shock-expansion method is generally the superior of the two, and in most cases gives values of the normal force derivatives of the flares which agree very well with the experimental results. Centers of pressure of the flares are presented and comparisons are made with results obtained from the theories mentioned. In general, the comparisons show that the assumption of conical flow over the flares is comparable to use of the second-order shock-expansion method in determining the centers of pressure, and in many cases both methods give values which agree closely with the experimental results.

Kirk, Donn B.↗
NASA NTRS1975

Computation of three-dimensional, inviscid supersonic flows

The paper sets forth in detail a method for the finite-difference computation of three-dimensional supersonic fields in an Eulerian mesh. First-, second-, and third-order finite difference schemes are examined. Attention is given to proper treatment of the impermeable and permeable boundaries encompassing the computational plane. Numerical results are presented for certain specific configurations: a conical wing-body combination, internal corner flow, a two-dimensional blunt body, an interfering shock problem, and three-dimensional inviscid supersonic flow past a shuttle-orbiter type vehicle.

Kutler, P.↗
NASA NTRS1973

A computer program for calculating the perfect gas inviscid flow field about blunt axisymmetric bodies at an angle of attack of 0 deg

A method for the rapid calculation of the inviscid shock layer about blunt axisymmetric bodies at an angle of attack of 0 deg has been developed. The procedure is of an inverse nature, that is, a shock wave is assumed and calculations proceed along rays normal to the shock. The solution is iterated until the given body is computed. The flow field solution procedure is programed at the Langley Research Center for the Control Data 6600 computer. The geometries specified in the program are sphores, ellipsoids, paraboloids, and hyperboloids which may conical afterbodies. The normal momentum equation is replaced with an approximate algebraic expression. This simplification significantly reduces machine computation time. Comparisons of the present results with shock shapes and surface pressure distributions obtained by the more exact methods indicate that the program provides reasonably accurate results for smooth bodies in axisymmetric flow. However, further research is required to establish the proper approximate form of the normal momentum equation for the two-dimensional case.

Zoby, E. V.↗
NASA NTRS1986

Application of NCOREL to conical multi-finned and multi-faceted configurations

A more versatile analytic conformal mapping approach for grid generation is implemented in a full potential supersonic flow code (NCOREL). Configurations such as multi-finned bodies and wings with vertical tails cannot be treated using a single conformal mapping transformation for grid generation. Instead, a series of analytic conformal mappings are used in progression to generate grids that are capable of resolving the complex multiple shock flow fields that exist about these configurations. Aplications of the grid generation techniques are presented for a variety of cross sections along with their conical full potential flow solutions.

Siclari, M. J.↗
NASA NTRS2010

Design of Modular, Shape-transitioning Inlets for a Conical Hypersonic Vehicle

For a hypersonic vehicle, propelled by scramjet engines, integration of the engines and airframe is highly desirable. Thus, the forward capture shape of the engine inlet should conform to the vehicle body shape. Furthermore, the use of modular engines places a constraint on the shape of the inlet sidewalls. Finally, one may desire a combustor cross- section shape that is different from that of the inlet. These shape constraints for the inlet can be accommodated by employing a streamline-tracing and lofting technique. This design technique was developed by Smart for inlets with a rectangular-to-elliptical shape transition. In this paper, we generalise that technique to produce inlets that conform to arbitrary shape requirements. As an example, we show the design of a body-integrated hypersonic inlet on a winged-cone vehicle, typical of what might be used in a three-stage orbital launch system. The special challenge of inlet design for this conical vehicle at an angle-of-attack is also discussed. That challenge is that the bow shock sits relatively close to the vehicle body.

Gollan, Rowan J.↗
NASA NTRS2014

Wind-US Results for the AIAA 2nd Propulsion Aerodynamics Workshop

This presentation contains Wind-US results presented at the 2nd Propulsion Aerodynamics Workshop. The workshop was organized by the American Institute of Aeronautics and Astronautics, Air Breathing Propulsion Systems Integration Technical Committee with the purpose of assessing the accuracy of computational fluid dynamics for air breathing propulsion applications. Attendees included representatives from government, industry, academia, and commercial software companies. Participants were encouraged to explore and discuss all aspects of the simulation process including the effects of mesh type and refinement, solver numerical schemes, and turbulence modeling. The first set of challenge cases involved computing the thrust and discharge coefficients for a 25deg conical nozzle for a range of nozzle pressure ratios between 1.4 and 7.0. Participants were also asked to simulate two cases in which the 25deg conical nozzle was bifurcated by a solid plate, resulting in vortex shedding (NPR=1.6) and shifted plume shock (NPR=4.0). A second set of nozzle cases involved computing the discharge and thrust coefficients for a convergent dual stream nozzle for a range of subsonic nozzle pressure ratios. The workshop committee also compared the plume mixing of these cases across various codes and models. The final test case was a serpentine inlet diffuser with an outlet to inlet area ratio of 1.52 and an offset of 1.34 times the inlet diameter. Boundary layer profiles, wall static pressure, and total pressure at downstream rake locations were examined.

Wind-US↗
NASA NTRS1975

Installation and airspeed effects on jet shock-associated noise

Experimental acoustic data are presented to illustrate, at model scale, the effect of varying the nozzle-wing installation on shock-associated noise, statically and with airspeed. The variation in installations included nozzle only, nozzle under-the-wing (with and without flaps deflected), and nozzle over-the-wing (unattached flow). The nozzles used were a conical and a 6-tube mixer nozzle with a cold-flow nozzle pressure ratio of 2.1. A 33-cm diameter free jet was used to simulate airspeed. With the nozzle only, shock wave noise dominated the spectra in the forward quadrant, while jet mixing noise dominated in the rearward quadrant. Similar trends were observed when a wing (flaps retracted) was included. Shock noise was attenuated with an over-the-wing configuration and increased with an under-the-wing configuration (due to reflection from the wing surface). With increasing flap deflection (under-the-wing configuration), the jet-flap interaction noise exceeded the shock noise and became dominant in both quadrants. The free jet results showed that airspeed had no effect on shock noise. The free jet noise data were corrected for convective amplification to approximate flight and comparisons between the various configurations are made.

Vonglahn, U.↗
NASA NTRS1974

An approximate inviscid radiating flow-field analysis for sphere-cone Venusian entry vehicles

A computational method based on the earlier work of one of the authors has been improved and modified to provide an accurate and rapid prediction of the radiating flow about blunt conical probes entering the atmosphere of Venus. Special features include a more general approximate equation of state, a more rapidly converging iteration scheme, a 38-step absorption coefficient model for a Venus atmosphere gas mixture model, and a shock-shape formula which yields a computed body shape in excellent agreement with the desired body. The method was used to calculate distributions of radiative heating for a large spherically blunted conical probe vehicle (1.219 m base diameter) and for three small spherically blunted conical probe vehicles (0.724 m base diameter). Solutions obtained with the presently developed approximate method required short computing times of the order of 1 to 3 minutes for each complete solution and gave agreements of 10% to 15% with the more exact predictions.

Falanga, R. A.↗
NASA NTRS1988

Shatter cones: Diagnostic impact signatures

Uniquely fractured target rocks known as shatter cones are associated with more than one half the world's 120 or so presently known impact structures. Shatter cones are a form of tensile rock failure in which a positive conical plug separates from a negative outer cup or mold and delicate ornaments radiating from an apex are preserved on surfaces of both portions. Although distinct, shatter cones are sometimes confused with other striated geologic features such as ventifacts, stylolites, cone-in-cone, slickensides, and artificial blast plumes. Complete cones or solitary cones are rare, occurrences are usually as swarms in thoroughly fractured rock. Shatter cones may form in a zone where an expanding shock wave propagating through a target decays to form an elastic wave. Near this transition zone, the expanding primary wave may strike a pebble or other inhomogeneity whose contrasting transmission properties produce a scattered secondary wave. Interference between primary and secondary scattered waves produce conical stress fields with axes perpendicular to the plane of an advancing shock front. This model supports mechanism capable of producing such shatter cone properties as orientation, apical clasts, lithic dependence, and shock pressure zonation. Although formational mechanics are still poorly understood, shatter cones have become the simplest geologic field criterion for recognizing astroblemes (ancient terrestrial impact structures).

Mchone, J. F.↗
NASA NTRS1976

Exit of a blast wave from a conical nozzle

The Eulerian computer code DORF was used in the analysis of a two-dimensional, unsteady flow field resulting from semi-confined explosions for propulsive applications. Initially, the ambient gas inside the conical shaped nozzle is set into motion due to the expansion of the explosion product gas, forming a shock wave. When this shock front exits the nozzle, it takes almost a spherical form while a complex interaction between the nozzle and compression and rarefaction waves takes place behind the shock. The results show an excellent agreement with experimental data.

Kim, K.↗
NASA NTRS1993

Prediction and control of vortex-dominated and vortex-wake flows

This progress report documents the accomplishments achieved in the period from December 1, 1992 until November 30, 1993. These accomplishments include publications, national and international presentations, NASA presentations, and the research group supported under this grant. Topics covered by documents incorporated into this progress report include: active control of asymmetric conical flow using spinning and rotary oscillation; supersonic vortex breakdown over a delta wing in transonic flow; shock-vortex interaction over a 65-degree delta wing in transonic flow; three dimensional supersonic vortex breakdown; numerical simulation and physical aspects of supersonic vortex breakdown; and prediction of asymmetric vortical flows around slender bodies using Navier-Stokes equations.

Kandil, Osama↗
NASA NTRS1963

Application of Dorodnitsyn's Integral Method to Nonequilibrium Flows over Pointed Bodies

Dorodnitsyn's integral method is used to obtain an approximate solution to the supersonic nonequilibrium flow over pointed bodies with attached shock waves. The partial differential equations governing the flow are converted to an approximate set of ordinary equations, which are solved by numerical integration starting at the body tip. Detailed analytical and numerical results for the first approximation are presented, considering the vibrational relaxation of a diatomic gas over a wedge or cone. It is shown that the first approximation yields: (1) The exact flow-variable gradients at the wedge tip (2) Expressions for the flow-variable gradients at the cone tip which are in agreement with extrapolations of characteristics calculations (3) A good approximate algebraic solution for frozen or equilibrium conical flow (4) An approximate expression for the nonequilibrium-flow stream function which affords a means of obtaining variations across the shock layer of the temperature and vibrational energy. Numerical results for both the wedge and cone compare favorably with identical cases computed by the method of characteristics.

NONEQUILIBRIUM FLOW↗
NASA NTRS1992

Unsteady separation in sharp fin-induced shock wave/turbulent boundary layer interaction at Mach 5

Fluctuating wall-pressure measurements are made in shock-wave/turbulent-boundary-layer interactions generated by sharp/unswept fins at angles of attack of 16, 18, 20, 22, 24, 26, and 28 degrees at Mach 5. The experiment was conducted under approximately adiabatic wall temperature conditions. The mean and rms pressure distributions can be collapsed in conical coordinates. The wall-pressure signal near separation is intermittent for all angles of attack (16-28 deg) and is qualitatively similar to that measured in unswept flows. However, the shock frequencies are higher - about 5 kHz compared to 0.5-1 kHz. Over the range of sweepbacks examined, from 25-55 deg, the spectral content of the fluctuating pressures does not change. Thus, the increase in separation-shock frequency from 1 to 5 kHz occurs at lower interaction sweepback and is not a continuous process with increasing sweepback. Power spectra at the position of maximum rms in the intermittent region for interactions in different incoming boundary layers have the same center frequency. The maximum rms in the intermittent region correlates with interaction sweepback, not with overall inviscid pressure rise.

Schmisseur, J. D.↗
NASA NTRS1976

Wing shielding of high-velocity jet and shock-associated noise with cold and hot flow jets

Jet exhaust noise shielding data are presented for cold and hot flows (ambient to 1100 K) and pressure ratios from 1.7 to 2.75. A nominal 9.5-cm diameter conical nozzle was used with simple shielding surfaces that were varied in length from 28.8 to 114.3 cm. The nozzle was located 8.8 cm above the surfaces. The acoustic data with the various shielding lengths are compared to each other and to that for the nozzle alone. In general, short shielding surfaces that provided shielding for subsonic jets did not provide as much shielding for jets with shock noise; however, long shielding surfaces did shield shock noise effectively.

Von Glahn, U.↗
NASA NTRS2000

Internal Designs Application for Inlet and Nozzle Aeroperformance Improvement

The following research results are based on development of an approach previously proposed by the authors for optimum nozzle design to obtain maximum thrust. The design was denoted a Telescope nozzle. A Telescope nozzle contains one or several internal designs of certain location, which are inserted at certain locations into a divergent conical or planar main nozzle near its exit. Such a design provides additional thrust augmentation over 20% by comparison with the optimum single nozzle of equivalent lateral area. What is more, recent experimental acoustic tests have discovered an essential noise reduction due to Telescope nozzles application. In this paper, some additional theoretical results are presented for Telescope nozzles and a similar approach is applied for aeroperformance improvement of a supersonic inlet. In addition, a classic gas dynamics problem of a similar supersonic flow into a plate has been analyzed. In some particular cases, new exact analytical solutions are obtained for a flow into a wedge with an oblique shock wave. Numerical simulations were conducted for supersonic flow into a divergent portion of a 2D or axisymmetric nozzle with several plane or conical designs as well as into a 2D or axisymmetric supersonic inlet with a forebody. The 1st order Kryko-Godunov marching numerical scheme for inviscid supersonic flows was used. Several cases were tested using the NASA CFL3d code based on full Navier-Stokes equations. Numerical simulation results have confirmed essential benefits of Telescope design applications in propulsion systems.

Gilinsky, M.↗