Search NASA⌕ Search

SEARCH · Search NASA

Results for “control electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Induction Linac Pulsers

The pulsers used in most of the induction linacs evolved from the very large body of work that was done in the U.S. and Great Britain during the development of the pulsed magnetron for radar. The radar modulators started at {approx}100 kW and reached >10 MW by 1945. A typical pulse length was 1 {mu}s at a repetition rate of 1,000 pps. A very comprehensive account of the modulator development is Pulse Generators by Lebacqz and Glasoe, one of the Radiation Laboratory Series. There are many permutations of possible modulators, two of the choices being tube type and line type. In earlier notes I wrote that technically the vacuum tube pulser met all of our induction linac needs, in the sense that a number of tubes, in series and parallel if required, could produce our pulses, regulate their voltage, be useable in feed-forward correctors, and provide a low source impedance. At a lower speed, an FET array is similar, and we have obtained and tested a large array capable of >10 MW switching. A modulator with an electronically controlled output only needs a capacitor for energy storage and in a switched mode can transfer the energy from the capacitor to the load at high efficiency. Driving a full size Astron induction core and a simulated resistive 'beam load' we achieved >50% efficiency. These electronically controlled output pulses can produce the pulses we desire but are not used because of their high cost. The second choice, the line type pulser, visually comprises a closing switch and a distributed or a lumped element transmission line. The typical switch cannot open or stop conducting after the desired pulse has been produced, and consequently all of the initially stored energy is dissipated. This approximately halves the efficiency, and the original cost estimating program LIACEP used this factor of two, even though our circuits are usually worse, and even though our inveterate optimists often omit it. The 'missing' energy is that which is reflected back into the line from mismatches, the energy left in the accelerator module's capacitance, the energy lost in the switch during switching and during the pulse, and the energy lost in the pulse line charging circuit. For example, a simple resistor-limited power supply dissipates as much energy as it delivers to the pulse forming line, giving a factor if two by itself, therefore efficiency requires a more complicated charging system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Active control of electron cyclotron emission radiometer channel frequencies for improved electron temperature measurements

As advanced scenarios are developed for tokamak operations, the demand for flexibility of the electron cyclotron emission (ECE) channels’ locations has increased. The tunable feature of yttrium iron garnet (YIG) filters provides this spatial flexibility. Here, we present a method of performing ECE measurements on fixed flux surfaces instead of fixed frequencies. This is achieved by adjusting YIG filters utilized in the intermediate frequency section to frequencies associated with flux surfaces in regions of interest during the discharge. Here, the key components are the application of tunable YIG filters and a control program that calculates the filter settings using flux information from real-time reconstruction equilibria (EFIT). This fast procedure facilitates T e measurements in regions of interest to investigate plasma dynamic behaviors.

47 OTHER INSTRUMENTATION↗

Development of a Kalman filter estimator for simulation and control of particulate matter distribution of a diesel catalyzed particulate filter

The knowledge of the temperature and particulate matter mass distribution is essential for monitoring the performance and durability of a catalyzed particulate filter. A catalyzed particulate filter model was developed, and it showed capability to accurately predict temperature and particulate matter mass distribution and pressure drop across the catalyzed particulate filter. However, the high-fidelity model is computationally demanding. Therefore, a reduced order multi-zone particulate filter model was developed to reduce computational complexity with an acceptable level of accuracy. In order to develop a reduced order model, a parametric study was carried out to determine the number of zones necessary for aftertreatment control applications. The catalyzed particulate filter model was further reduced by carrying out a sensitivity study of the selected model assumptions. The reduced order multi-zone particulate filter model with 5 × 5 zones was selected to develop a catalyzed particulate filter state estimator considering its computational time and accuracy. Next, a Kalman filter–based catalyzed particulate filter estimator was developed to estimate unknown states of the catalyzed particulate filter such as temperature and particulate matter mass distribution and pressure drop (Δ P) using the sensor inputs to the engine electronic control unit and the reduced order multi-zone particulate filter model. A diesel oxidation catalyst estimator was also integrated with the catalyzed particulate filter estimator in order to provide estimates of diesel oxidation catalyst outlet concentrations of NO 2 and hydrocarbons and inlet temperature for the catalyzed particulate filter estimator. The combined diesel oxidation catalyst–catalyzed particulate filter estimator was validated for an active regeneration experiment. The validation results for catalyzed particulate filter temperature distribution showed that the root mean square temperature error by using the diesel oxidation catalyst–catalyzed particulate filter estimator is within 3.2 °C compared to the experimental data. Similarly, the Δ P estimator closely simulated the measured total Δ P and the estimated cake pressure drop error is within 0.2 kPa compared to the high-fidelity catalyzed particulate filter model.

Engineering↗

Location specific solidification microstructure control in electron beam melting of Ti-6Al-4V

Relationships between prior beta grain size in solidified Ti-6Al-4V and melting process parameters in the Electron Beam Melting (EBM) process are investigated. Samples are built by varying a machine-dependent proprietary speed function to cover the process space. Optical microscopy is used to measure prior beta grain widths and assess the number of prior beta grains present in a melt pool in the raster region of the build. Despite the complicated evolution of beta grain sizes, the beta grain width scales with melt pool width. The resulting understanding of the relationship between primary machine variables and prior beta grain widths is a key step toward enabling the location specific control of as-built microstructure in the EBM process. Control of grain width in separate specimens and within a single specimen is demonstrated.

42 ENGINEERING↗

Controlling the electronic structure of graphene using surface-adsorbate interactions

Hybridization of atomic orbitals in graphene on Ni(111) opens up a large energy gap of ≈2.8eV between nonhybridized states at the K point. Here we use alkali-metal adsorbate to reduce and even eliminate this energy gap, and also identify a new mechanism responsible for decoupling graphene from the Ni substrate without intercalation of atomic species underneath. Using angle-resolved photoemission spectroscopy and density functional theory calculations, we show that the energy gap is reduced to 1.3 eV due to moderate decoupling after adsorption of Na on top of graphene. Calculations confirm that after adsorption of Na, graphene bonding to Ni is much weaker due to a reduced overlap of atomic orbitals, which results from n doping of graphene. Finally, we show that the energy gap is eliminated by strong decoupling resulting in a quasifreestanding graphene, which is achieved by subsequent intercalation of the Na underneath graphene. Furthermore, the ability to partially decouple graphene from a Ni substrate via n doping, with or without intercalation, suggests that the graphene-to-substrate interaction could be controlled dynamically.

36 MATERIALS SCIENCE↗

Self-corrected Sensors Based On Atomic Absorption Spectroscopy For Atom Flux Measurements In Molecular Beam Epitaxy

A high sensitivity atom flux sensor based on atomic absorption spectroscopy has been designed and implemented to control electron beam evaporators and effusion cells in a molecular beam epitaxy system. Using a high-resolution spectrometer and a two-dimensional charge coupled device (CCD) detector in a double-beam configuration, we employ a non-resonant line or a resonant line with lower absorbance from the same hollow cathode lamp as the reference for nearly perfect background correction and baseline drift removal. This setup also significantly shortens the warm-up time needed compared to other sensor technologies and drastically reduces the noise coming from the surrounding environment. In addition, the high-resolution spectrometer allows the most sensitive resonant line to be isolated and used to provide excellent signal-to-noise ratio.

Environmental Molecular Sciences Laboratory↗

Comparison of the Accuracy and Speed of Transient Mobile A/C System Simulation Models: Preprint

The operation of air conditioning (A/C) systems is a significant contributor to the total amount of fuel used by light- and heavy-duty vehicles. Therefore, continued improvement of the efficiency of these mobile A/C systems is important. Numerical simulation has been used to reduce the system development time and to improve the electronic controls, but numerical models that include highly detailed physics run slower than desired for carrying out vehicle-focused drive cycle-based system optimization. Therefore, faster models are needed even if some accuracy is sacrificed. In this study, a validated model with highly detailed physics, the 'Fully-Detailed' model, and two models with different levels of simplification, the 'Quasi-Transient' and the 'Mapped- Component' models, are compared. The Quasi-Transient model applies some simplifications compared to the Fully-Detailed model to allow faster model execution speeds. The Mapped-Component model is similar to the Quasi-Transient model except instead of detailed flow and heat transfer calculations in the heat exchangers, it uses lookup tables created with the Quasi-Transient model. All three models are set up to represent the same physical A/C system and the same electronic controls. Speed and results of the three model versions are compared for steady state and transient operation. Steady state simulated data are also compared to measured data. The results show that the Quasi-Transient and Mapped-Component models ran much faster than the Fully-Detailed model, on the order of 10- and 100-fold, respectively. They also adequately approach the results of the Fully-Detailed model for steady-state operation, and for drive cycle-based efficiency predictions

02 PETROLEUM↗

Two-step fabrication technique of gold tips for use in point-contact spectroscopy

For a successful point-contact spectroscopy (PCS) measurement, metallic tips of proper shape and smoothness are essential to ensure the ballistic nature of a point-contact junction. Until recently, the fabrication of Au tips suitable for use in point-contact spectroscopy has remained more of an art involving a trial and error method rather than an automated scientific process. To address these issues, we have developed a technique with which one can prepare high quality Au tips reproducibly and systematically. It involves an electronic control of the driving voltages used for an electrochemical etching of a gold wire in a HCl-glycerol mixture or a HCl solution. We find that a stopping current, below which the circuit is set to shut off, is a single very important parameter to produce an Au tip of desired shape. We present detailed descriptions for a two-step etching process for Au tips and also test results from PCS measurements using them.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Controlling Structural, Electronic, and Energy Flow Dynamics of Catalytic Processes through Tailored Nanostructures

MoS 2 (molybdenum disulfide) is a highly-versatile catalyst material for support of numerous reactions from hydrodesulfurization and denitrogenation to the focus of this renewal proposal: hydrogenation of CO/CO 2 towards (higher) alcohols. At the same time, MoS 2 is a non-toxic, environmentally-benign and rather inert material- which under ambient conditions for some time has served as a lubricant and, more recently, as next-generation electronic material. The apparent contrast between inertness and stability in ambient, and catalytic activity under reactive conditions is puzzling and calls for a synergistic theoretical and experimental investigation with the long-term objective of enabling the rational design of MoS 2 -based catalysts for alcohol-formation reactions by providing a microscopic understanding of the environmental factors that determines site activity and selectivity. Our research project seeks answers to the questions (a) what conformation does MoS 2 adopt under reaction conditions (as opposed to that under ultrahigh vacuum and low temperatures)?; (b) what reaction pathways exist on such a material?; (c) how can the local environment of the active sites be manipulated so as to make MoS 2 an efficient catalyst for production of higher alcohol from syngas? In particular, research strategies will explore how the basal plane composed of sulfur atoms can be activated so as to exhibit a reactivity of its own, by addressing three research targets and building on extensive preliminary and enabling work: (1) vacancies and vacancy aggregates on the basal plane; (2) non-local catalyst transformation through alkali doping, hydrogenation and phase transition; (3) fabrication of a metal-nanoparticle-activated MoS 2 system, in which particle anchoring, reactive sites and pathways as well as selectivity are controlled by design, as an example of predictive development of a catalyst material,. All strategies are directed to improve the efficacy of the key reactive sites and selectivity of chemical pathways by design, to replace the inefficient methodology of trial and error in catalyst development. This research project represents a synergistic combination of computational guidance, foundational surface-science-based experiments and validation under reactive conditions that aims at transformative new insights into the working of MoS 2 -based hydrogenation-catalysts, a topic squarely at the center of the interest of DOE BES. Guided and led by Talat Rahman, a computational physicist, this project will apply density functional theory to understand structure, reaction pathways and chemical potentials associated with MoS 2 -based CO/CO 2 hydrogenation, augmented by kinetic Monte Carlo methods for reaction rates and prefactors as well as ab-initio molecular dynamics for evaluation of thermal stability. Complementary experimental input and validation will originate from co-PI Ludwig Bartels, a physical chemist and materials scientist, whose group focuses on local imaging and preparation of MoS 2 materials, from co-PI Peter Dowben, an experimental physicist, whose group is expert in the spectroscopy of occupied and unoccupied electronic states, and from senior collaborator Michael White of Brookhaven National Laboratory, whose group generates high-resolution electronic and activity information on size-selected well-defined metal chalcogenide clusters. This collaborative effort will enable a comprehensive understanding of the correlation of structural integrity and catalytic activity of MoS 2 in forms ranging from extended films to individual particles with known geometries and binding sites. Alcohol formation from syngas is a rapidly emerging application that has great potential through facile, economic, and decentralized biomass gasification. CO 2 activation is one of the most pressing concerns of our time: increasing CO 2 levels in the atmosphere change the climate and expose the globe to environmental transformations with the potential for enormous economic and societal impact. We will investigate CO/CO 2 hydrogenation via an interdisciplinary research collaboration with established synergy – one that, in accordance with the mission of the DOE, involves accredited Hispanic-Serving Institutions and that, through student exchange with international collaborators and National Labs, will directly benefit a broad spectrum of communities and generate human resources in sciences essential to their future.

2D materials↗

Formation of the active medium in high-power repetitively pulsed gas lasers pumped by an electron-beam-controlled discharge

A high-power repetitively pulsed e-beam-controlled discharge CO{sub 2} laser is simulated numerically; the simulation results are compared with experimental data. Optimal sizes and design of electrodes and configuration of the external magnetic field are found, which allow one to introduce no less than 90% electric pump energy into a specified volume of the active medium, including the active volume of a laser with an aperture of 110 × 110 cm. The results obtained can also be used to design other types of highpower gas lasers. (lasers)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Large Built‐In Fields Control the Electronic Properties of Nanoscale Molecular Devices with Dipolar Structures

Abstract Large area molecular junctions are nanoscale materials made of a molecular layer sandwiched between two metal electrodes. In this study, a fundamental property of these systems is demonstrated: the emergence of a large built‐in field, typically as high as 10 9 V m −1 , and susceptible to appear in any junction possessing an asymmetry. This field originates from permanent dipoles in the contacted molecular layer and is responsible for a large renormalization of the band alignment in the junction. To illustrate this effect, a predictive theoretical characterization of two realistic gold‐thiolate‐based organic layers is carried out. The parameters leading to the emergence of the built‐in field are given and the very large renormalization effect is interpreted in terms of an applied voltage drop. Despite a high significance, this generic feature of molecular junctions has widely been neglected hitherto in the design and interpretation of molecular device characteristics. Built‐in fields provide a powerful way to achieve structure–property relationships in molecular junctions, by taking advantage of dipolar nanometric building blocks.

Van Dyck, Colin↗

Control of electron transfer in nitrogenase

The bacterial enzyme nitrogenase achieves the reduction of dinitrogen (N 2 ) to ammonia (NH 3 ) utilizing electrons, protons, and energy from the hydrolysis of ATP. Building on earlier foundational knowledge, recent studies provide molecular-level details on how the energy of ATP hydrolysis is utilized, the sequencing of multiple electron transfer events, and the nature of energy transduction across this large protein complex. Here, we review the state of knowledge about energy transduction in nitrogenase.

Seefeldt, Lance C. (ORCID:0000000264579504)↗

Subsurface Interface Structure Controlling Local Electronic Properties of Epitaxial Graphene on SiC(0001)

Recently realized high-mobility semiconducting epitaxial graphene on silicon carbide (SiC) [Zhao, J. Nature 2024, 625 (7993), 60−65, 10.1038/s41586-023-06811-0] provided an important step toward integration of the graphene-based system into active components in postsilicon micro- and nanoelectronics. However, the exact atomic-scale structure and complex bonding configurations of the first epitaxial graphene carbon layer (C buffer ) remain an open problem. Our recent report [Kolmer, M. Communications Physics 2024, 7 (1), 16, 10.1038/s42005-023-01515-3] has shed new light on understanding this interface, where the external transverse electric field-dependent dynamic switching behavior of the C buffer –SiC bonds was observed. Here, using scanning tunneling microscopy and spectroscopy (STM and STS), we present direct evidence of silicon (Si) vacancies at the interface and provide their distribution at the topmost reconstructed SiC(0001) layer. Bias voltage and epitaxial graphene thickness-dependent characterization of the collective C buffer –SiC interface showed that “Si” vacancy sites beneath C buffer are stable under STM electric fields. Moreover, the vacancies introduce localized electronic states below the Fermi level, thereby enhancing the charge-transfer phenomenon across the interface.

Thupakula, Umamahesh [Ames Laboratory (AMES), Ames↗