Search NASA⌕ Search

SEARCH · Search NASA

Results for “corrosion defect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Fundamental Studies of Tritium Diffusivity in Pure and Defective Zircaloy-4 Getters (Tritium Science Program FY2020 Report)

Zirconium (Zr) alloys are extensively used as tritium (T) getters in nuclear reactors due to their low absorption cross section to thermal neutron, good mechanical properties at high temperature and resistant to corrosion in different environmental conditions. Zr alloys have better thermal properties than many other refractory alloys including stainless steel. The nuclear characteristic is simulated, and T is produced in tritium-producing burnable absorber rods (TPBAR) by the irradiation of neutron flux in pressurized water reactor (PWR). T thus produced diffuses through the pellets and is captured by the getter where it chemically reacts with Zr to form metal hydride (ZrTx). These hydrides are brittle and affect adversely the mechanical properties of alloys. In addition to that, mismatch in the lattice structures after hydride formation creates a stress which needs to be considered in component design and their life evaluation. Therefore, understanding the behavior of T and its species becomes significant as fuel burnup is increased, which leads to increase in hydrogen pickup and oxide formation. The transport of T and its species in pure Zr alloys, and in alloys with certain alloying elements and defects are important to understand in order to enhance the performance of the materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electrochemical Evolution of Fuel Cell Platinum Nanocatalysts on Carbon Nanotubes at the Atomic Scale

The evolution of Pt nanoparticles supported on carbon nanotubes is analyzed before and after electrochemical potential cycling, using identical location aberration-corrected transmission electron microscopy, for applications in proton exchange membrane fuel cells. The work is focused on the half-cell accelerated stress test protocol of potential cycles ranging between 1.0 and 1.5 V RHE to represent the start-up/shutdown settings of a fuel cell vehicle. The research work reveals that particle migration and coalescence are key mechanisms for a reduction in the Pt nanoparticle surface area at the early stages of potential cycling. Further, the mechanism for particle movement and coalescence is attributed to carbon corrosion, catalyzed either by Pt or by bulk corrosion of the carbon nanotubes. Carbon corrosion results in the appearance of carbon vacancies at the carbon nanotube/Pt nanoparticle interface during cycling, as well as the formation of edge and surface defects. During cycling, the concentration of the dissoluble Pt increases. As soon as a significant amount is reached, subnanometer/atomic clusters emerge on the carbon nanotube support, which can move and coalesce, or redeposit on the surface of larger particles through Ostwald ripening.

25 ENERGY STORAGE↗
DOE OSTI2023

Atomic motifs govern the decoration of grain boundaries by interstitial solutes

Abstract Grain boundaries, the two-dimensional defects between differently oriented crystals, tend to preferentially attract solutes for segregation. Solute segregation has a significant effect on the mechanical and transport properties of materials. At the atomic level, however, the interplay of structure and composition of grain boundaries remains elusive, especially with respect to light interstitial solutes like B and C. Here, we use Fe alloyed with B and C to exploit the strong interdependence of interface structure and chemistry via charge-density imaging and atom probe tomography methods. Direct imaging and quantifying of light interstitial solutes at grain boundaries provide insight into decoration tendencies governed by atomic motifs. We find that even a change in the inclination of the grain boundary plane with identical misorientation impacts grain boundary composition and atomic arrangement. Thus, it is the smallest structural hierarchical level, the atomic motifs, that controls the most important chemical properties of the grain boundaries. This insight not only closes a missing link between the structure and chemical composition of such defects but also enables the targeted design and passivation of the chemical state of grain boundaries to free them from their role as entry gates for corrosion, hydrogen embrittlement, or mechanical failure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of Cu on the passivity of Ti–xCu (x = 0, 3 and 5 wt%) alloy in phosphate-buffered saline solution within the framework of PDM-II

The effect of copper content on the passivity of Ti–xCu alloys in a phosphate-buffered saline electrolyte (pH 7.4), in the steady-state condition, was examined using potentiostatic polarization, electrochemical impedance spectroscopy, and Mott-Schottky analysis. The study demonstrates that the oxide layer forms on the Ti–xCu alloys surface have n-type semiconducting character, and the steady-state thickness of the oxide layer is observed linearly and depends on the applied potential. The study observations are in line with the predictions of the Point Defect Model (PDM-II), which provides a physiochemically realistic description of the oxide layer formation on Ti–xCu alloys. The observations reveal that the Cu additions result in a decrease in the charge transfer resistance and capacitances associated with the hydroxide and barrier layer, an increase in the donor density, and reduce the electrochemical resistance of the Ti–xCu alloys. The study also exhibits that the decrease in the steady-state current density after the initial addition of 3 wt% of Cu is attributed to the progressive substitution of copper on the cation sublattice of the film resulting in enhanced electrostatic interaction between the immobilized copper $Cu^{x'}_{Ti}$, and the mobile cation interstitials $Cu^{+}_{i}$, which carries the excess current over and that conveyed by oxygen vacancies $V^{••}_o$ in the barrier layer. Moreover, it is also observed that over a hundred-year implant period, about 0.006 cm (0.06 mm) of Ti–3Cu alloy is predicted to lose due to steady-state corrosion in the PBS solution under the given set of conditions, it is further seen that, as the Cu amount increased from 3 wt% to 5 wt% in the Ti–xCu alloys, the steady-state corrosion rate decreases.

Electrochemical Impedance Spectroscopy↗
DOE OSTI2024

Critical role of slags in pitting corrosion of additively manufactured stainless steel in simulated seawater

Abstract Pitting corrosion in seawater is one of the most difficult forms of corrosion to identify and control. A workhorse material for marine applications, 316L stainless steel (316L SS) is known to balance resistance to pitting with good mechanical properties. The advent of additive manufacturing (AM), particularly laser powder bed fusion (LPBF), has prompted numerous microstructural and mechanical investigations of LPBF 316L SS; however, the origins of pitting corrosion on as-built surfaces is unknown, despite their utmost importance for certification of LPBF 316L SS prior to fielding. Here, we show that Mn-rich silicate slags are responsible for pitting of the as-built LPBF material in sodium chloride due to their introduction of deleterious defects such as cracks or surface oxide heterogeneities. In addition, we explain how slags are formed in the liquid metal and deposited at the as-built surfaces using high-fidelity melt pool simulations. Our work uncovers how LPBF changes surface oxides due to rapid solidification and high-temperature oxidation, leading to fundamentally different pitting corrosion mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Interfacial stabilization for inverted perovskite solar cells with long-term stability

Perovskite solar cells (PSCs) commonly exhibit significant performance degradation due to ion migration through the top charge transport layer and ultimately metal electrode corrosion. Here, we demonstrate an interfacial management strategy using a boron chloride subphthalocyanine (Cl 6 SubPc)/fullerene electron-transport layer, which not only passivates the interfacial defects in the perovskite, but also suppresses halide diffusion as evidenced by multiple techniques, including visual element mapping by electron energy loss spectroscopy. As a result, we obtain inverted PSCs with an efficiency of 22.0% (21.3% certified), shelf life of 7000 h, Τ 80 of 816 h under damp heat stress (compared to less than 20 h without Cl 6 SubPc), and initial performance retention of 98% after 2000 h at 80 °C in inert environment, 90% after 2034 h of illumination and maximum power point tracking in ambient for encapsulated devices and 95% after 1272 h outdoor testing ISOS-O-1. Our strategy and results pave a new way to move PSCs forward to their potential commercialization solidly.

14 SOLAR ENERGY↗
DOE OSTI2020

The origin of passivity in aluminum-manganese solid solutions

In this work, the effects of manganese on the aqueous corrosion of aluminum-manganese alloys were investigated by experiments and atomistic simulations. Electrochemical measurements, x-ray photoelectron spectroscopy, and atom probe tomography analysis indicate that manganese addition enhanced the corrosion resistance of aluminum without participating in the surface oxidation. Furthermore, the selective dissolution of manganese was believed to increase the free volume at the metal/oxide interface to facilitate the formation of a denser, thinner oxide layer with closer to stoichiometry composition. Atomistic simulations showed that the oxide layer compactness increased, and defect density decreased with increasing free volume content in Al, resulting in enhanced barrier characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding grain boundary segregation under irradiation: A mesoscale modeling study

Grain boundaries (GBs) are an important component in the design of irradiation resistant materials as they play a crucial role as point defect sinks for non-equilibrium vacancies and self-interstitials. However, in the presence of sustained point defect fluxes, the coupled transport of atomic components with inherently different diffusivities often leads to radiation-induced segregation (RIS), with undesired effects on properties such as intergranular corrosion and stress-assisted cracking. In this talk, we investigate the fundamental mechanisms leading to GB segregation in BCC FeCr-based alloys using multiscale modeling and experiments. A phase-field model is employed to account for both thermodynamic and kinetic segregation mechanisms. The full Onsager transport matrix is derived using kinetic Monte Carlo, molecular dynamics, and kinetic cluster expansion (KineCluE) calculations. The thermodynamics of GB segregation is described via an atomic density-based modification to the CALPHAD free energy. The modeling predictions are then compared against segregation data from atom probe characterization for various temperatures, compositions, and neutron irradiation conditions. We will conclude by discussing the utility of the multiscale modeling approach to shed light on the fundamental mechanisms leading to solute-GB interaction.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effective Corrosion-Resistant Single-Atom Alloy Catalyst on HfO 2 -Passivated BiVO 4 Photoanode for Durable (≈800 h) Solar Water Oxidation

Green hydrogen (H 2 ) production from solar water splitting necessitates photoelectrodes with superior photoelectrochemical (PEC) activity and durability. However, surface defects and photocorrosion instability—especially at high potentials—limit PEC performance and stability. Herein, the prototypical bismuth vanadate (BiVO 4 ) photoanode is used to demonstrate a holistic approach to improve photocurrent density and long-term stability. In this approach, high surface-area nanostructuring of BiVO 4 is combined with barium (Ba) doping with semi-crystalline hafnium oxide (HfO 2 ) surface passivation and single-atom nickel platinum (NiPt) catalysts. The introduction of Ba 2+ ions into BiVO 4 increases the concentration of conductive V 4+ ions or the ratio of V 4+ ions to oxygen vacancies, avoiding V 5+ dissolution during water oxidation. The semi-crystalline HfO 2 , which serves as a passivation layer, prevents BiVO 4 photocorrosion by suppressing harmful chemical reactions when holes are transferred to the electrolyte. The synergistic use of isolated single-atom and Ni-Pt coordination improves charge transfer at the photoanode/electrolyte interface, leading to enhanced PEC kinetics and stability. As a result, a photoelectrode is demonstrated with ≈6.5 mA cm -2 at 1.23 V versus a reversible hydrogen electrode (RHE) and continuous operation for 800 h with a negligible degradation rate. This work provides a promising approach to improve photoanodes for PEC H 2 production.

08 HYDROGEN↗
DOE OSTI2025

Vacancy-Dependent Diffusion Mechanism in Oxygen-Defective SrFeO 3 Perovskite Materials: First-Principles Density Functional Theory and Experimental Approach

Understanding oxygen diffusion at the atomic scale in SrFeO 3−δ perovskites is crucial for developing oxygen storage materials with optimal performance. Such materials are required to have high stability, corrosion resistance, and acceptable oxygen storage capacity at moderate operating temperatures and pressures. Here, in this study, we used first-principles density functional theory and thermogravimetric analysis to study the vacancy-dependent oxygen diffusion in oxygen-deficient SrFeO 3−δ (δ = 0, 0.065, 0.125, 0.25, 0.5) perovskites. The electronic structures, including the partial- and spin-resolved density of states, for different SrFeO 3−δ phases were calculated and compared with available experimental and theoretical results. By mapping the migration pathways, we investigated diffusion mechanisms and calculated the energy barriers for oxygen diffusion in cubic, orthorhombic, and brownmillerite phases of SrFeO 3−δ perovskites. Using the calculated energy barriers, we deduced the diffusion time scales and diffusion coefficients within SrFeO 3−δ . A diffusion coefficient on the order of 10 –8 m 2 /s was obtained for SrFeO 2.875 . We experimentally investigated the roles of temperature and oxygen partial pressures on the redox kinetics and deduced the kinetics rate and diffusion density, which agreed well with the calculated values for the density of diffusing oxygen vacancy in the lattice. Our results showed that the energy barrier tends to reduce at higher oxygen concentrations. Our results serve as an important guideline for designing oxygen storage materials with optimal redox kinetics.

chemical looping with oxygen uncoupling (CLOU)↗
DOE OSTI2020

Resolving atomic transport through iron oxide under irradiation using isotopic tracers

Structural materials in nuclear environments are exposed to complex and harsh conditions, including high temperatures, corrosive solutions, and irradiation. Material stability and likewise degradation are fundamentally controlled by atomic transport mechanisms. Here, we investigate the influence of radiation-induced, non-equilibrium point defect populations on mass transport within model oxide systems using isotopic tracers and atom probe tomography. An isotopically labelled hematite (a-Fe2O3) film was synthesized with 16O- and 18O-rich layers (>30nm and 10 nm, respectively) sequentially deposited via molecular beam epitaxy. One region of the film was proton irradiated to ~0.1 dpa at 450°C, and regions outside the beam spot provided a non-irradiated control of thermal annealing only. 3D APT was used to directly visualize the elemental and O-isotopic redistribution following both thermal and combined thermal and irradiation conditions. Complementary scanning transmission electron microscopy (STEM) was also employed to study the microstructural evolution. Error function fits of the 18O-concentration profiles enabled quantification of diffusion coefficients.

isotopic tracers, diffusion, proton irradiation, h↗
NASA NTRS1989

Making Jointless Dual-Diameter Tubes

Welds between sections having different diameters eliminated. Single tube made with integral tapered transition section between straight sections of different diameters and wall thicknesses. Made from single piece; contains no joints, welded or otherwise. Not prone to such weld defects as voids and need not be inspected for them. Tube fabricated by either of two methods: drawing or reduction. Both methods used to fabricate tubes of 316L corrosion-resistant stainless steel for use as heat-exchanger coil.

Kirkham, Kathleen E.↗
DOE OSTI2024

Vacancy-mediated transport and segregation tendencies of solutes in FCC Ni under diffusional creep

Nickel-based alloys are known for their excellent corrosion resistance and high-temperature strength. However, at high temperatures, polycrystals experience grain boundary-stress-driven vacancy diffusion leading to diffusion-driven creep. Understanding the fundamentals of defect migration is essential to predict diffusion creep behavior. In this talk, we explore the Nabarro-Herring diffusion creep and the associated solute segregation that is likely to result from the different diffusivities of the solute and solvent elements. Density functional theory calculations are performed to determine the formation, migration and binding energies of the solute and vacancy defects in stress-free and stressed states. The dilute-limit transport coefficients are then calculated using the self-consistent mean field theory as implemented in the Kinetic Cluster Expansion (KineCluE) code. Predictions of diffusion creep strain rates and solute segregation are then presented for various solutes, stress and temperatures. This work opens research avenues for exploration of diffusion creep via characterization of elemental segregation to grain boundaries.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Design Evaluation of High Reliability Lithium Batteries

Within one year, a lithium battery design can be qualified for device use through the application of accelerated discharge testing, calorimetry measurements, real time tests and other supplemental testing. Materials and corrosion testing verify that the battery components remain functional during expected battery life. By combining these various methods, a high reliability lithium battery can be manufactured for applications which require zero defect battery performance.

Buchman, R. C.↗
DOE OSTI2022

Niobium addition improves the corrosion resistance of TiHfZrNb x high-entropy alloys in Hanks’ solution

High-strength TiHfZrNb x high-entropy alloys could become the ideal materials for small-diameter endovascular stents once their corrosion resistance in the physiological milieu is confirmed. Here, this work aims at evaluating the corrosion resistance of a TiHfZrNb x high-entropy-alloys family in Hanks’ solution at 37 °C and revealing the influence of niobium on the mechanisms of dissolution and passivation. The alloys were subjected to a series of static and dynamic electrochemical tests and surface characterization, employing the static/dynamic/cyclic polarizations, impedance spectroscopy, XPS, AFM, and SEM. Results confirm a higher corrosion resistance of the alloys compared to that of CP-Ti and Ti6Al4V. The addition of niobium considerably improves the microstructural homogeneity that ensures a low dissolution rate and a greater resistance of the film due to the lower concentration of point defects. The passive film behaves as an n-type semiconductor and is composed of a mixture of TiO 2 , Nb 2 O 5 , ZrO 2 , and HfO 2 oxides, with the presence of metallic hydroxides on the outermost layer. A detailed description of the niobium influence on the mechanisms of the dissolution and passivation is presented in this work.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Hydrothermal Corrosion of First-Generation Dual-Purpose Coatings on Silicon Carbide for Accident-Tolerant Fuel Cladding

In this study, four different commercial coatings, TiN, Cr, CrN, and Cr/CrN (multilayer) were deposited by physical vapor deposition (PVD) on high resistivity chemical vapor deposited (CVD) SiC for the dual purpose of corrosion mitigation and fission gas hermeticity. The coatings were exposed for up to 2600 hours in flowing high temperature (288-350°C), high purity, liquid water with dissolved hydrogen (0.15-3ppm) or dissolved oxygen (1-2ppm). The Cr/CrN coatings did not adhere well and spalled quickly during exposure. In oxygenated conditions, none of the coatings were protective . CrN coatings spalled preferentially at defect sites, but reacted slowly enough in the absence of defects to potentially be chemically protective. TiN coatings fully oxidized within a few hundred hours and spalled. In hydrogen, all the coatings were chemically stable. Coating failures were identified and attributed to localized spallation, potentially related to coating defects. Coating improvements are recommended to reduce spallation and improve coating protection for future generations of dual-purpose coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Co-extrusion of dissimilar Al alloys via shear assisted processing and extrusion

Cladded tubes are generally used where two distinct properties are required at the outer and inner part of a tube, for instance, strength and corrosion resistance. In this investigation, shear assisted processing and extrusion (ShAPE) was employed to fabricate bi-metallic tubes from 1100 and 7075, and 1100 and 2024 dissimilar Al alloy combinations. Surface defect-free bi-metallic tubes were fabricated via the ShAPE process. Detailed microstructural characterization of the interface and various locations of the cladded tubes were carried out using light and scanning electron microscopy techniques. A defect-free, metallurgically bonded interface between the cladded layer and high strength Al (7075 and 2024 Al) was observed. Furthermore, hardness and tensile properties of the cladded ShAPE tubes were examined in the as-extruded conditions.

Komarasamy, Mageshwari↗
NASA NTRS2009

Spacecraft Electrical Connector Selection and Application Processes

This assessment was initiated by the NASA Engineering & Safety Center (NESC) after a number of recent "high profile" connector problems, the most visible and publicized of these being the problem with the Space Shuttle's Engine Cut-Off System cryogenic feed-thru connector. The NESC commissioned a review of NASA's connector selection and application processes for space flight applications, including how lessons learned and past problem records are fed back into the processes to avoid recurring issues. Team members were primarily from the various NASA Centers and included connector and electrical parts specialists. The commissioned study was conducted on spacecraft connector selection and application processes at NASA Centers. The team also compared the NASA spacecraft connector selection and application process to the military process, identified recent high profile connector failures, and analyzed problem report data looking for trends and common occurrences. The team characterized NASA's connector problem experience into a list of top connector issues based on anecdotal evidence of a system's impact and commonality between Centers. These top issues are as follows, in no particular rank order: electrically shorted, bent and/or recessed contact pins, contact pin/socket contamination leading to electrically open or intermittencies, connector plating corrosion or corrosion of connector components, low or inadequate contact pin retention forces, contact crimp failures, unmated connectors and mis-wiring due to workmanship errors during installation or maintenance, loose connectors due to manufacturing defects such as wavy washer and worn bayonet retention, damaged connector elastomeric seals and cryogenic connector failure. A survey was also conducted of SAE Connector AE-8C1 committee members regarding their experience relative to the NASA concerns on connectors. The most common responses in order of occurrence were contact retention, plating issues, worn-out or damaged coupling mechanisms, bent pins, contact crimp barrel cracking and torn seals. In addition to these common themes, responses included issues with markings, dimensional errors on the build, contact/socket damage (handling), manufacturing defects and customer misapplication and mishandling. The NESC team concluded that considering the large quantity and wide variety of connectors successfully flown on human and robotic space applications, the number of failures is quite low. However, "high profile" failures with significant cost, schedule, safety, and/or mission success impacts continue to occur. It was also concluded that connector failures occur throughout a system's life-cycle with the majority of connector issues application related. A number of recommendations were identified for improving NASA connector selection processes and overall space connector reliability and performance.

Iannello, Chris↗