Search NASA⌕ Search

SEARCH · Search NASA

Results for “crossflow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

A simplified model for the viscous crossflow in a slotted test section

A simplified physical model was constructed which simulates the viscous crossflow in a fluid layer near the slots at a fixed streamwise location in a slotted wind tunnel. For low to moderate Reynolds numbers, numerical solutions of the two dimensional, incompressible Navier-Stokes equations in stream function and vorticity, which govern the model flow, were obtained. Fairly general slot geometry was incorporated by means of the Thompson-Thames-Mastin transformation. An approximate factorization scheme with cyclic acceleration parameters was employed to solve a finite difference analog of the stream function equation. The vorticity equation was numerically solved with a modified version of the classical alternating direction implicit scheme. Although no quantitative assessment of solution accuracy can be made, numerical results for variations in incremental wall pressure around the slat are at least qualitatively similar to some experimental results.

Cooke, C. H.↗
NASA NTRS1979

Periodic steamwise variations of heat transfer coefficients for incline and staggered arrays of circular jets with crossflow of spent air

Heat transfer characteristics were measured for inline and staggered arrays of circular jets impinging on a surface parallel to the jet orifice plate. The impinging flow was constrained to exit in a single direction along the channel formed by the jet plate and the heat transfer surface. In this configuration the air discharged from upstream transverse rows of jet holes imposes a crossflow of increasing magnitude on the succeeding downstream jet rows. Streamwise heat transfer coefficient profiles were determined for a streamwise resolution of one-third the streamwise hole spacing, utilizing a specially constructed test surface.

Florschuetz, L. W.↗
NASA NTRS1981

A simplified model for the viscous crossflow in a slotted test section

A simplified physical model is constructed which simulates the viscous crossflow in a fluid layer near the slots at a fixed streamwise location in a slotted wind tunnel. For low to moderate Reynolds numbers, numerical solutions of the two-dimensional, incompressible Navier-Stokes equations in stream function and vorticity, which govern the model flow, are obtained. Fairly general slot geometry is incorporated by means of the Thompson-Thames-Mastin transformation. An approximate factorization scheme with cyclic acceleration parameters is employed to solve a finite difference analog of the stream function equation. The vorticity equation is numerically solved with a modified version of the classical alternating direction implicit (ADI) scheme. Although no quantitative assessment of solution accuracy can be made, numerical results for variations in incremental wall pressure around the slot are at least qualitatively similar to some experimental results of Berndt and Sorenson.

Cooke, C. H.↗
NASA NTRS1981

Crossflow effects on steady and fluctuating pressures on an ogive-cylinder cone-frustum model in supersonic separated flow

Wind-tunnel tests were conducted on an ogive-cylinder model with two axisymmetric protuberances having cone frustum angles of cone = 23 deg and 45 deg that were used to generate detached shock waves and the resulting separated flow areas downstream of the shock. The tests were conducted in a 9 by 7 foot supersonic wind tunnel at a free-stream Mach number of 2.0 and at Reynolds numbers of 1.5 x 1 million and 3.9 x 1 million, based on body diameter. The model had an afterbody fineness ratio of 8.3, and the ogive nose had a fineness ratio of 3.0. Two characteristics of the fluctuating pressures in surface vortex flows that result from the crossflow component, (velocity along the tunnel longitudinal axis free stream angle of attack), in combination with changes in the longitudinal pressure gradient were measured: (1) the broadband, rms-pressure coefficients and (2) the power spectral densities. Measurements are presented for various flow regions on the model such as the attached turbulent boundary layer, the detached frustum shock wave, and separated flow areas. The results indicate that the pressure fluctuations around or in the neighborhood of the foci of the vortex flows had broadband intensities and power spectral densities nearly identical to the levels previously measured in separated-flow regions at angles of attack of 0 deg.

Dods, J. B., Jr.↗
NASA NTRS1982

Effect of location in an array on heat transfer to a cylinder in crossflow

An experiment was conducted to measure the heat transfer from a heated cylinder in crossflow in an array of circular cylinders. All cylinders had a length-to-diameter ratio of 3.0. Both in-line and staggered array patterns were studied. The cylinders were spaced 2.67 diameters apart center-to-center in both the axial and transverse directions to the flow. The row containing the heated cylinder remained in a fixed position in the channel and the relative location of this row within the array was changed by adding up to five upstream rows. The working fluid was nitrogen gas at pressures from 100 to 600 kPa. The Reynolds number ranged based on cylinder diameter and average unobstructed channel velocity was from 5,000 to 125,000. Turbulence intensity: profiles were measured for each case at a point one half space upstream of the row containing the heated cylinder. The basis of comparison for all the heat transfer data was the single row with the heated cylinder. For the in-line cases the addition of a single row of cylinders upstream of the row containing the heated cylinder increased the heat transfer by an average of 50 percent above the base case. Adding up to five more rows caused no increase or decrease in heat transfer. Adding rows in the staggered array cases resulted in average increases in heat transfer of 21, 64, 58, 46, and 46 percent for one to five upstream rows, respectively.

Simoneau, R. J.↗
NASA NTRS1981

Determination of wind tunnel constraint effects by a unified pressure signature method. Part 2: Application to jet-in-crossflow

The development of an improved jet-in-crossflow model for estimating wind tunnel blockage and angle-of-attack interference is described. Experiments showed that the simpler existing models fall seriously short of representing far-field flows properly. A new, vortex-source-doublet (VSD) model was therefore developed which employs curved trajectories and experimentally-based singularity strengths. The new model is consistent with existing and new experimental data and it predicts tunnel wall (i.e. far-field) pressures properly. It is implemented as a preprocessor to the wall-pressure-signature-based tunnel interference predictor. The supporting experiments and theoretical studies revealed some new results. Comparative flow field measurements with 1-inch "free-air" and 3-inch impinging jets showed that vortex penetration into the flow, in diameters, was almost unaltered until 'hard' impingement occurred. In modeling impinging cases, a 'plume redirection' term was introduced which is apparently absent in previous models. The effects of this term were found to be very significant.

Hackett, J. E.↗
NASA NTRS1981

Experimental investigation of a jet inclined to a subsonic crossflow

Experimental investigations have been conducted to determine the surface-pressure distribution on a flat plate and a body of revolution with a jet issuing at a large angle to the free stream and to obtain a better understanding of the entrainment mechanism close to the jet exit by quantitative mean velocity surveys. Pressure data were obtained with a flat plate model at several nozzle injection angles using a single round nozzle. For the body of revolution model, data were obtained with a round jet exhausting perpendicular to the crossflow and with two round jets spaced two to six nozzle diameters apart. Mean velocity measurements were obtained with laser velocimeter surveys near the base of a round jet exhausting normal to a flat plate. For the flat plate model, the pressure field shifts downstream and the entrainment effect decreases with decreasing nozzle injection angle. For the body of revolution model with two jets, the jet-induced effect of the rear jet on the surface-pressure distribution was less than the front jet. The flow regions close to the jet are defined by the laser surveys, but further mean velocity surveys are required to understand the entrainment mechanism.

Aoyagi, K.↗
NASA NTRS1982

Heat transfer from combustion gases to a single row of closely spaced tubes in a swirl crossflow Stirling engine heater

This paper describes an experimental program to determine the heat-transfer characteristics of a combustor and heat-exchanger system in a hybrid solar receiver which utilizes a Stirling engine. The system consists of a swirl combustor with a crossflow heat exchanger composed of a single row of 48 closely spaced curved tubes. In the present study, heat-transfer characteristics of the combustor/heat-exchanger system without a Stirling engine have been studied over a range of operating conditions and output levels using water as the working fluid. Nondimensional heat-transfer coefficients based on total heat transfer have been obtained and are compared with available literature data. The results show significantly enhanced heat transfer for the present geometry and test conditions. Also, heat transfer along the length of the tubes is found to vary, the effect depending upon test condition.

Bankston, C. P.↗
NASA NTRS1983

Comparison of predicted and experimental external heat transfer around a film cooled cylinder in crossflow

Calculations were made of the film cooling provided by rows of holes around the circumference of a cylinder in crossflow and the results were compared to experimental data. The calculations and experimental data were for conditions that simulate most of those that are typical of air cooled turbine vane leading edges. Injection was from a single and multiple rows of holes located at different angular locations from the stagnation line. The holes in the rows were angled normal to the flow direction and at a 25 degree angle to the cylinder wall. The calculations and experimental data were for several constant values of blowing ratios for all rows and for different blowing ratios for each row, representing a simulation of a common coolant plenum supply to multiple rows of holes. The calculations were made using a finite difference boundary layer code, STAN5. Contrary to initial expectations that injection would trip the boundary layer flow into the turbulent regime, the results indicated that the high free stream acceleration apparently kept the flow laminar for holes in the first 45 degrees past stagnation. The trend in Stanton number reduction due to coolant injection was predicted with generally good agreement at the lower blowing rates, but for multile rows of holes, agreement was poor beyond the first row.

Stepka, F. S.↗
NASA NTRS1982

Analytical calculation of a single jet in crossflow and comparison with experiment

A series of calculations of a jet in crossflow using a three-dimensional finite difference model of the Navier-Stokes equations were made on a series of progressively finer grids. With a reasonable number of grid point (40x30x20), calculated jet penetration and mixing characteristics were found to compare favorably with the experimental measurements of Crabb, Durao and Whitelaw. The calculated results were grid dependent (i.e., numerical or false diffusion was present in the result). A finer grid calculation indicated that turbulence model deficiencies may become more noticeable in the calculated results as the magnitude of numerical diffusion is reduced.

Clauss, R. W.↗
NASA NTRS1983

Perspectives on the mixing of a row of jets with a confined crossflow

An interactive computer code, written for a microcomputer, is presented which displays 2-D and 3-D oblique plots of the temperature distribution downstream of jets mixing with a confined crossflow, for either single-side or opposed jet injection. Temperature profiles calculated with this routine are presented to show the effects of flow and geometric variables on the mixing. Examples are shown to illustrate the different perspectives on the mixing available by exercising various view options. In addition, the program is used to calculate profiles for opposed rows of jets with their centerlines in-line, by assuming that the confining effect of an opposite wall is equivalent to that of a plane of symmetry between opposed jets.

Holdeman, J. D.↗
NASA NTRS1982

Effects of free stream turbulence intensity and integral length scale on heat transfer from a circular cylinder in crossflow

A model has been proposed for the momentum eddy diffusivity induced by free stream turbulence intensity and integral length scale. The eddy diffusivity model is applied to a cylinder situated in a uniform crossflow in the presence of free stream turbulence. Numerical solution of the governing momentum and energy equations with the proposed eddy diffusivity model yielded results for the skin friction coefficient and the Nusselt number. The numerical predictions of the present work are compared with experimental data and the agreement between the two is seen to be very good.

Gorla, R. S. R.↗
NASA NTRS1982

Spanwise mass transfer variations on a cylinder in 'nominally' uniform crossflow

Mass transfer experiments on a circular cylinder in a 'nominally' uniform crossflow are described. Experiments were conducted at the tunnel's turbulence level and with a woven-wire turbulence screen. In both cases spanwise and circumferential mass transfer measurements were made. Without the turbulence screen, the results were found to be spanwise independent and agreed quite well with both theory and the result of others. In addition to the mass transfer measurements, spanwise traverse measurements of the mean velocity and turbulence quantities in the incident flow were made and showed that the screen produced a small-amplitude spanwise periodic perturbation in the incident flow. Although this perturbation was only one quarter of a percent in the mean velocity and buried in the stream's turbulence, disproportionately large spanwise variations of 15 percent were found in the mass transfer rate.

Mayle, R. E.↗
NASA NTRS1984

Effect of location in an array on heat transfer to a short cylinder in crossflow

An experiment was conducted to measure the heat transfer from a heated cylinder in crossflow in an array of circular cylinders. All cylinders had a length-to-diameter ratio of 3.0. Both in-line and staggered array patterns were studied. The cylinders were spaced 2.67 diameters apart center-to-center in both the axial and transverse directions to the flow. The row containing the heated cylinder remained in a fixed position in the channel and the relative location of this row within the array was changed by adding up to five upstream rows. The working fluid was nitrogen gas at pressures from 100 to 600 kPa. The Reynolds number range based on cylinder diameter and average unobstructed channel velocity was from 5,000 to 125,000. Turbulence intensity profiles were measured for each case at a point one half space upstream of the row containing the heated cylinder. The basis of comparison for all the heat transfer data was the single row with the heated cylinder. For the in-line cases the addition of a single row of cylinders upstream of the row containing the heated cylinder increased the heat transfer by an average of 50 percent above the base case. Adding up to five more rows caused no increase or decrease in heat transfer. Adding rows in the staggered array cases resulted in average increases in heat transfer of 21, 64, 58, 46, and 46 percent for one to five upstream rows, respectively. Previously announced in STAR as N82-19493

Simoneau, R. J.↗
NASA NTRS1984

Computer programs to predict induced effects of jets exhausting into a crossflow

A user's manual for two computer programs was developed to predict the induced effects of jets exhausting into a crossflow. Program JETPLT predicts pressures induced on an infinite flat plate by a jet exhausting at angles to the plate and Program JETBOD, in conjunction with a panel code, predicts pressures induced on a body of revolution by a jet exhausting normal to the surface. Both codes use a potential model of the jet and adjacent surface with empirical corrections for the viscous or nonpotential effects. This program manual contains a description of the use of both programs, instructions for preparation of input, descriptions of the output, limitations of the codes, and sample cases. In addition, procedures to extend both codes to include additional empirical correlations are described.

Perkins, S. C., Jr.↗
NASA NTRS1985

Flow visualization study of the effect of injection hole geometry on an inclined jet in crossflow

A flow visualization was studied by using neutrally buoyant, helium-filled soap bubbles, to determine the effect of injection hole geometry on the trajectory of an air jet in a crossflow and to investigate the mechanisms involved in jet deflection. Experimental variables were the blowing rate, and the injection hole geometry cusp facing upstream (CUS), cusp facing downstream (CDS), round, swirl passage, and oblong. It is indicated that jet deflection is governed by both the pressure drag forces and the entrainment of free-stream fluid into the jet flow. For injection hole geometries with similar cross-sectional areas and similar mass flow rates, the jet configuration with the larger aspect ratio experienced a greater deflection. Entrainment arises from lateral shearing forces on the sides of the jet, which set up a dual vortex motion within the jet and thereby cause some of the main-stream fluid momentum to be swept into the jet flow. This additional momentum forces the jet nearer the surface. Of the jet configurations, the oblong, CDS, and CUS configutations exhibited the largest deflections. The results correlate well with film cooling effectiveness data, which suggests a need to determine the jet exit configuration of optimum aspect ratio to provide maximum film cooling effectiveness.

Simon, F. F.↗
NASA NTRS1985

Numerical calculation of subsonic jets in crossflow with reduced numerical diffusion

A series of calculations are reported for two, subsonic jet in crossflow geometries. The parametric variation examined are the lateral spacing of a row of jets. The first series of calculations corresponds to a widely space jet geometry, S/D = 4, and the second series corresponds to closely spaced jets, S/D = 2. The calculations are done with alternate differencing schemes to illustrate the impact of numerical diffusion. The calculated jet trajectories agreed well with experimental data in the widely spaced jet geometry, but not in the closely spaced geometry.

Claus, R. W.↗
NASA NTRS1985

The influence of jet-grid turbulence on heat transfer from the stagnation region of a cylinder in crossflow

The effect of high-intensity turbulence on heat transfer from the stagnation region of a circular cylinder in crossflow was studied. The work was motivated by the desire to be able to more fully understand and predict the heat transfer to the leading edge of a turbine airfoil. In order to achieve high levels of turbulence with a reasonable degree of isotropy and homogeneity, a jet-injection turbulence grid was used. The jet grid provided turbulence intensities of 10 to 12 percent, measured at the test cylinder location, for downstream blowing with the blowing rate adjusted to an optimal value for flow uniformity. Heat transfer augmentation above the zeroturbulence case ranged from 37 to 53 percent for the test cylinder behind the jet grid for a cylinder Reynolds number range of 48,000 to 180,000, respectively. The level of heat transfer augmentation was found to be fairly uniform with respect to circumferential distance from the stagnation line. Stagnation point heat transfer results (expressed in terms of the Frossling number) were found to be somewhat low with respect to previous studies, when compared on the basis of equal values of the parameter Tu Re(1/2), indicating an additional Reynolds number effect as observed by previous investigators. Consequently, for a specified value of Tu Re(1/2), data obtained with a relatively high turbulence intensity will have a lower value of the Frossling number.

Obrien, J. E.↗