Search NASA⌕ Search

SEARCH · Search NASA

Results for “crystal plasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Optimization of spacecraft high temperature outgassing duration

Spacecraft systems are baked-out under vacuum to remove occluded and adsorbed gases, solvents, water, plasticizer, and other materials acquired during their manufacture. Two bakeouts of solar panels were carried out. Quartz crystal microbalances installed in the vacuum chamber during the tests and held at 273 K (0 C) provided an ongoing measure of the panels' outgassing. From these data, the panels' material weight losses versus time were obtained. A comparison of the total weight loss expected during a relatively long bakeout with that accomplished during a reasonable period of time was used as a criteria for an acceptable duration of the bakeout in order to optimize cost effectiveness.

Scialdone, J. J.↗
NASA NTRS1994

Effusive silicic volcanism in the Central Andes: The Chao dacite and other young lavas of the Altiplano-Puna Volcanic Complex

The largest known Quaternary silicic lava body in the world is Cerro Chao in north Chile, a 14-km-long coulee with a volume of at least 26 cu km. It is the largest of a group of several closely similar dacitic lavas erupted during a recent (less than 100,000 year old) magmatic episode in the Altiplano-Puna Volcanic Complex (APVC; 21-24 deg S) of the Centra; Andean Volcanic Zone. The eruption of Chao proceeded in three phases. Phase 1 was explosive and produced approximately 1 cu km of coarse, nonwelded dacitic pumice deposits and later block and ash flows that form an apron in front of the main lava body. Phase 2 was dominantly effusive and erupted approximately 22.5 cu km of magma in the form of a composite coulee covering approximately 53 sq km with a 400-m-high flow front and a small cone of poorly expanded pumice around the vent. The lava is homogeneous with rare flow banding and vesicular tops and selvages. Ogives (flow ridges) reaching heights of 30 m form prominent features on its surface. Phase 3 produced a 6-km-long, 3-km-wide flow that emanated from a collapsed dome. Ogives are subdued, and the lava is glassier than that produced in previous phases. All the Chao products are crystal-rich high-K dacites and rhyodacites with phenocrysts of plagioclase, quartz, hornblende, biotite, sphene, rare snidine, and oxides. Phenocryst contents reach 40-60 vol % (vesicle free) in the main phase 2 lavas but are lower in the phase 1 (20-25%) and phase 3 (approximately 40%) lavas. Ovoid andesitic inclusions with vesicular interiors and chilled margins up to 10 cm are found in the later stages of phase 2 and compose up to 5% of the phase 3 lava. There is little evidence for preeruptive zonation of the magma body in composition, temperature (approximately 840 C), fO2 (19(exp -11), or water content, so we propose that eruption of the Chao complex was driven by intrusion of fresh, hot andesitic magma into a crystallizing and largely homogeneous body of dacitic magma. Morphological measurements suggest that the Chao lavas had internal plastic viscosities of 10(exp 10) to 10(exp 12) Pa s, apparent viscosities of 10(exp 9) Pa s, surface viscosities of 10(exp 15) to 10(exp 24) Pa s, and a yield strength of 8 x 10(exp 5) Pa. These estimates indicate that Chao would have exhibited largely similar rheological properties to other silicic lava extrusions, notwithstanding its high phenocryst content. We suggest that Chao's anomalous size is a function of both the relatively steep local slope (20 deg to 3 deg) and the available volume of magma. The eruption duration for Chao's emplacement is thought to have been about 100 to 150 years, with maximum effusion rates of about 25 cu m/s for short periods. Four other lavas in the vicinity with volumes of approximately 5 cu km closely resemble Chao and are probably comagnetic. The suite as a whole shares a petrologic and chemical similarity with the voluminous regional Tertiary to Pleistocene ignimbrites of the APVC and may be derived from a zone of silicic magmatism that is thought to have been active since the late Tertiary. Chao and the other young lavas may represent either the waning of this system or a new episode fueled by intrusions of mafic magma.

De Silva, S. L.↗
NASA NTRS1989

The effect of hydrogen on the deformation behavior of a single crystal nickel-base superalloy

The effect of hydrogen on the tensile deformation behavior of PWA 1480 is presented. Tensile tests were interrupted at different plastic strain levels to observe the development of the dislocation structure. Transmission electron microscopy (TEM) foils were cut perpendicular to the tensile axis to allow the deformation of both phases to be simultaneously observed as well as parallel to zone axes (III) to show the superdislocations on their slip planes. Similar to other nickel-base superalloys, hydrogen was detrimental to the room temperature tensile properties of PWA 1480. There was little effect on strength, however the material was severely embrittled. Even without hydrogen, the elongation-to-failure was only approximately 3 percent. The tensile fracture surface was made up primarily of ductile voids with regions of cleavage fracture. These cleavage facets are the eutectic (gamma') in the microstructure. It was shown by quantitative fractography that hydrogen embrittles the eutectic (gamma') and causes the crack path to seek out and fracture through the eutectic (gamma'). There was two to three times the amount of cleavage on the fracture surface of the hydrogen-charged samples than on the surface of the uncharged samples. The effect of hydrogen can also be seen in the dislocation structure. There is a marked tendency for dislocation trapping in the gamma matrix with and without hydrogen at all plastic strain levels. Without hydrogen there is a high dislocation density in the gamma matrix leading to strain exhaustion in this region and failure through the matrix. The dislocation structure at failure with hydrogen is slightly different. The TEM foils cut parallel to zone axes (III) showed dislocations wrapping around gamma precipitates. Zone axes (001) foils show that there is a lower dislocation density in the gamma matrix which can be linked to the effects of hydrogen on the fracture behavior. The primary activity in the gamma precipitates is in the form of superlattice intrinsic stacking faults (SISFs). These faults have also been reported in other ordered alloys and superalloys.

Walston, W. S.↗
NASA NTRS1992

Prediction of dislocation generation during Bridgman growth of GaAs crystals

Dislocation densities are generated in GaAs single crystals due to the excessive thermal stresses induced by temperature variations during growth. A viscoplastic material model for GaAs, which takes into account the movement and multiplication of dislocations in the plastic deformation, is developed according to Haasen's theory. The dislocation density is expressed as an internal state variable in this dynamic viscoplastic model. The deformation process is a nonlinear function of stress, strain rate, dislocation density and temperature. The dislocation density in the GaAs crystal during vertical Bridgman growth is calculated using a nonlinear finite element model. The dislocation multiplication in GaAs crystals for several temperature fields obtained from thermal modeling of both the GTE GaAs experimental data and artificially designed data are investigated.

Tsai, C. T.↗
NASA NTRS1998

The Physics of Hard Spheres Experiment on MSL-1: Required Measurements and Instrument Performance

The Physics of HArd Spheres Experiment (PHaSE), one of NASA Lewis Research Center's first major light scattering experiments for microgravity research on complex fluids, flew on board the Space Shuttle's Microgravity Science Laboratory (MSL-1) in 1997. Using colloidal systems of various concentrations of micron-sized plastic spheres in a refractive index-matching fluid as test samples, illuminated by laser light during and after crystallization, investigations were conducted to measure the nucleation and growth rate of colloidal crystals as well as the structure, rheology, and dynamics of the equilibrium crystal. Together, these measurements support an enhanced understanding of the nature of the liquid-to-solid transition. Achievement of the science objectives required an accurate experimental determination of eight fundamental properties for the hard sphere colloidal samples. The instrument design met almost all of the original measurement requirements, but with compromise on the number of samples on which data were taken. The instrument performs 2-D Bragg and low angle scattering from 0.4 deg. to 60 deg., dynamic and single-channel static scattering from 10 deg. to 170 deg., rheology using fiber optics, and white light imaging of the sample. As a result, PHaSE provided a timely microgravity demonstration of critical light scattering measurement techniques and hardware concepts, while generating data already showing promise of interesting new scientific findings in the field of condensed matter physics.

Doherty, Michael P.↗
NASA NTRS1991

Electrostatic Stabilization Of Growing Protein Crystals

Proposed technique produces large crystals in compact, economical apparatus. Report presents concept for supporting protein crystals during growth in microgravity. Yields crystals larger and more-nearly perfect than those grown on Earth. Combines best features of sandwich-drop and electrostatic-levitation methods of support. Drop of protein solution inserted between pair of glass or plastic plates, as in sandwich-drop-support method. Electrostatically charged ring confines drop laterally and shapes it, as in electrostatic technique. Apparatus also made to accommodate several drops simultaneously between same pair of supporting plates. Drops can be inserted and crystals removed through ducts in plates.

Shlichta, Paul J.↗
NASA NTRS1990

A simplified orthotropic viscoplasticity theory based on overstress

The viscoplasticity theory based on overstress, a simplified version of Sutcu (1985) theory, is presented for the case of orthotropy. The theory permits asymptotic solutions for checking numerical experiments and for identification of material properties. It is applicable to materials with rate(time) dependence, hysteresis, and a permanent set, such as cubic crystals, directionally solidified alloys, and metal matrix composites. Though it is a unified type theory, with effects of creep and plasticity not separated, it allows to identify viscous and plastic contributions to the stress in the asymptotic state.

Sutcu, M.↗
NASA NTRS1986

Crack growth in single-crystal silicon

Crack growth in single-crystal silicon at room temperature in air was evaluated by double torsion (DT) load-relaxation method and monitored by acoustic emission (AE) technique. Both DT and AE methods indicated lack of subcritical crack growth in silicon. At the critical stress intensity factor, the crack front was found to be jumping several times in a 'mirror' region and then followed by fast crack growth in a 'hackle' region. Hackle marks were found to be associated with plastic deformation at the tip of the fast moving crack. No dislocation etch pits were found in the 'mirror' region, in which crack growth may result from interatomic bonds broken at the crack tip under stress without any plastic deformation. Acoustic emission appears to be spontaneously generated from both interatomic bonds broken and dislocation generation at the moving crack tip during the crack growth in single-crystal silicon.

Chen, C. P.↗
NASA NTRS1976

Micromechanics of slip bands on a free surface

A micromechanics analysis for the formation and propagation of slip bands on the free surface of a polycrystal under monotonic loading is presented. For the growth of slip bands, the analysis satisfies the conditions of both equilibrium and displacement continuity, as well as the relation between slip and the resolved shear stress throughout the polycrystal. Numerical calculations show how the microstress field causes the concentration of plastic deformation in discrete sliding bands and give results which are in good qualitative agreement with known slip band observations on aluminum single crystals.

Lin, S. R.↗
NASA NTRS2019

Water Storage and Transport Processes During Impact Experiments on Nominally Anhydrous Minerals

Water, in the form of structurally bound hydrogen in the crystal lattice of nominally anhydrous minerals (NAMs), strongly influences many important physical processes on terrestrial planets and planetary objects. Water enhances the rates of plastic deformation and controls the degree of partial melting in silicate rocks, which influences the generation of melt and therefore the nature of planetary volcanism. Water has also been experimentally demonstrated to influence the nature of lattice preferred orientation in deformed aggregates, and thus may be important in the interpretation of seismic anisotropy data collected from planetary bodies, such as from the current InSight mission on Mars. Therefore, much attention has been focused on characterizing the distribution and concentration of water in the planets and rocky bodies of our solar system.

Tielke, J.↗
NASA NTRS1982

Intermetallics as alternative materials

Aluminum containing intermetallics have B2 cubic crystal structures, exist over a wide range of composition, have large solubilities for third element alloying additions, are capable of both low and high temperature plastic flow, and have very high melting temperatures (approximately 1900 K) except for FeAl. The slow strain rate elevated temperature properties of Fe, Ni, and Co aluminides are investigated. Because of the reported difficulties with traditional melting/casting methods, sound polycrystalling materials are fabricated by hot extrusion of steel canned blended prealloyed powders. These binary aluminides are used to develop base line elevated temperature mechanical properties as well as an understanding of the factors which affect/control the strength and ductility.

Whittenberger, J. D.↗
NASA NTRS2003

Finite Element Modeling of a Cylindrical Contact Using Hertzian Assumptions

The turbine blades in the high-pressure fuel turbopump/alternate turbopump (HPFTP/AT) are subjected to hot gases rapidly flowing around them. This flow excites vibrations in the blades. Naturally, one has to worry about resonance, so a damping device was added to dissipate some energy from the system. The foundation is now laid for a very complex problem. The damper is in contact with the blade, so now there are contact stresses (both normal and tangential) to contend with. Since these stresses can be very high, it is not all that difficult to yield the material. Friction is another non-linearity and the blade is made out of a Nickel-based single-crystal superalloy that is orthotropic. A few approaches exist to solve such a problem and computer models, using contact elements, have been built with friction, plasticity, etc. These models are quite cumbersome and require many hours to solve just one load case and material orientation. A simpler approach is required. Ideally, the model should be simplified so the analysis can be conducted faster. When working with contact problems determining the contact patch and the stresses in the material are the main concerns. Closed-form solutions for non-conforming bodies, developed by Hertz, made out of isotropic materials are readily available. More involved solutions for 3-D cases using different materials are also available. The question is this: can Hertzian1 solutions be applied, or superimposed, to more complicated problems-like those involving anisotropic materials? That is the point of the investigation here. If these results agree with the more complicated computer models, then the analytical solutions can be used in lieu of the numerical solutions that take a very long time to process. As time goes on, the analytical solution will eventually have to include things like friction and plasticity. The models in this report use no contact elements and are essentially an applied load problem using Hertzian assumptions to determine the contact patch dimensions.

Knudsen, Erik↗
NASA NTRS1991

Experimental modeling of jet-ring turbine disk cooling

The experimental facility and some early results are described from a current research program modeling turbine disk cooling with multiple impinging jets, such as employed on the Space Shuttle Main Engine oxygen turbopump. The study is designed to obtain detailed local convection heat transfer rates on specially constructed turbine disk models that employ either multiple cooling jet impingement near the disk outer radius from a jet ring, or alternatively, single entrance coolant supply into the center of the disk cavity. Jet impingement is an effective scheme for cooling of turbine disks at or near the blade attachment region, but the heat transfer mechanisms and merits relative to other schemes are not well understood. The present study employs two specially constructed full scale plastic model disks, contoured and plane, together with the corresponding stators. Local heat transfer rates are determined by a computer vision system from the response of thin liquid crystal coatings applied to the disk test faces. The present results indicate that multiple jet impingement directed at the blade attachment region results in higher cooling rates in that region than does the same flow supplied to the disk center, but this conclusion must be regarded as tentative.

Metzger, D. E.↗
NASA NTRS1974

Physical property measurements of doped cesium iodide crystals

Mechanical and thermal property values are reported for crystalline cesium iodide doped with sodium and thallium. Young's modulus, bulk modulus, shear modulus, and Poisson's ratio were obtained from ultrasonic measurements. Young's modulus and the samples' elastic and plastic behavior were also measured under tension and compression. Thermal expansion and thermal conductivity were the temperature dependent measurements that were made.

Synder, R. S.↗
NASA NTRS1979

Electrotransport purification of thorium under low pressure conditions

It was demonstrated that the ultrapurification of refractory metals by electrotransport refining could best be accomplished in the noncontaminating environment of an orbiting low density materials laboratory such as the Molecular Shield Device. Refining experiments were performed at 2 x 10 to the -12th Torr which resulted in the preparation of small quantities of the World's purest thorium metal. The microgravity occurring in orbit was simulated electromagnetically and shown to be advantageous in eliminating grain-sliding caused by the plastic deformation of the sample at high temperature. The electrotransport sample assembly was tested in several environments including simulated solar irradiation, coldness and darkness and under various pressure conditions. Ultrapure single crystals of alpha thorium were also prepared and characterized. Laboratory electronics for the experiment were developed and a totally automatic control system was used to heat the specimens.

Schmidt, F. A.↗
NASA NTRS1972

Aluminium. II - A review of deformation properties of high purity aluminium and dilute aluminium alloys.

The elastic and plastic deformation behavior of high-purity aluminum and of dilute aluminum alloys is reviewed. Reliable property data, including elastic moduli, elastic coefficients, tensile, creep, fatigue, hardness, and impact are presented. Single crystal tensile results are discussed. Rather comprehensive reference lists, containing publications of the past 20 years, are included for each of the above categories. Defect structures and mechanisms responsible for mechanical behavior are presented. Strengthening techniques (alloys, cold work, irradiation, quenching, composites) and recovery are briefly reviewed.

Reed, R. P.↗