Search NASA⌕ Search

SEARCH · Search NASA

Results for “current attack”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

The Solar Maximum Mission

The Solar Maximum Mission spacecraft, launched on 1980 February 14, carries seven instruments for the study of solar flares and other aspects of solar activity. These instruments observe in spectral ranges from gamma-rays through the visible, using imaging, spectroscopy, and high-time-resolution light curves to study flare phenomena. In addition, one instrument incorporates an active cavity radiometer for accurate measurement of the total solar radiant output. This paper reviews some of the most important current observational and theoretical questions of solar flare physics and indicates the ways in which the experiments on SMM will be able to attack these questions. The SMM observing program is described.

Chipman, E. G.↗

Prop-fan airfoil icing characteristics

An icing test program was carried out during the 1986-87 and 1987-88 icing seasons at the Fluidyne Icing Tunnel. The testing consisted of evaluating the icing characteristics and aerodynamic performance characteristics of two thin, two-dimensional airfoil sections. The two airfoils were a NACA Series 16-203 and a Hamilton Standard PF1-304, 3 and 4 percent thickness-to-chord ratio airfoils, respectively. These airfoils are representative of the thin airfoils currently being evaluated for Prop-Fan propulsion systems. The tests were conducted over a wide range of icing conditions, angles-of-attack, and Mach numbers (0.3 to 0.8).

Pike, J. A.↗

Report of the Panel on Aerodynamics

Progress in aerodynamics over the past 50 years has been evidenced by the development of increasingly sophisticated and efficient flight vehicles throughout the flight spectrum. Advances have generally arisen in an evolutionary manner from experience gained in wind tunnel testing, flight testing, and improvements in analytical and computational capabilities. As a result of this evolutionary development, both military and commercial vehicles operate at a relatively high efficiency level. This observation plus the fact that airplanes have not changed appreciably in outward appearance over recent years has led some skeptics to conclude incorrectly that aerodynamics is a mature technology, with little to be gained from further developments in the field. It is of interest to note that progress in aerodynamics has occurred without a thorough understanding of the fundamental physics of flow, turbulence, vortex dynamics, and separated flow, for example. The present understanding of transition, turbulence, and boundary layer separation is actually very limited. However, these fundamental flow phenomena provide the key to reducing the viscous drag of aircraft. Drag reduction provides the greatest potential for increased flight efficiency from the standpoint of both saving energy and maximizing performance. Recent advances have led to innovative concepts for reducing turbulent friction drag by modifying the turbulent structure within the boundary layer. Further advances in this basic area should lead to methods for reducing skin friction drag significantly. The current challenges for military aircraft open entirely new fields of investigation for the aerodynamicist. The ability through very high speed information processing technology to totally integrate the flight and propulsion controls can permit an aircraft to fly with "complete abandon," avoiding departure, buffet, and other undesirable characteristics. To utilize these new control concepts, complex aerodynamic phenomena will have to be understood, predicted, and controlled. Current requirements for military aircraft include configuration optimization through a widened envelope from subsonic to supersonic and from low to high angles of attack. This task is further complicated by requirements for control of observables. These challenging new designs do not have the luxury of a large experimental data base from which to optimize for various parameter combinations. Consequently, there exists a strong need for better techniques, both experimental and computational, to permit design optimization in a complete sense.

Bradley, Richard G.↗

Evaluation of Scaling Methods for Rotorcraft Icing

This paper reports result of an experimental study in the NASA Glenn Icing Research Tunnel (IRT) to evaluate how well the current recommended scaling methods developed for fixed-wing unprotected surface icing applications might apply to representative rotor blades at finite angle of attack. Unlike the fixed-wing case, there is no single scaling method that has been systematically developed and evaluated for rotorcraft icing applications. In the present study, scaling was based on the modified Ruff method with scale velocity determined by maintaining constant Weber number. Models were unswept NACA 0012 wing sections. The reference model had a chord of 91.4 cm and scale model had a chord of 35.6 cm. Reference tests were conducted with velocities of 76 and 100 kt (39 and 52 m/s), droplet MVDs of 150 and 195 fun, and with stagnation-point freezing fractions of 0.3 and 0.5 at angle of attack of 0deg and 5deg. It was shown that good ice shape scaling was achieved for NACA 0012 airfoils with angle of attack lip to 5deg.

Tsao, Jen-Ching↗

HLPW-4/GMGW-3: Wall-Modeled LES and Lattice-Boltzmann Technology Focus Group Workshop Summary

A summary of the nine submissions to the Wall-Modeled LES and Lattice-Boltzmann(WMLESLB) Technical Focus Group (TFG) at the 4th High lift Prediction Workshop is provided. The focus of this TFG was to assess the current capabilities of WMLES and Lattice-Boltzmann methods on a complex high-lift configuration across a wide range of angles of attack. Preliminary analysis of the submitted data suggests that>250𝑀spatial degrees of freedom are needed to accurately predict pitching moments at high angles of attack due to large pressure gradients present on the outboard slat and main element for𝛼 >17◦(corrected for free-air).While some scatter is reported in pitching moments at the low-angles of attack (𝛼 <11◦) - likely caused by differences in flap separation possibly due to low Reynolds number effects - excellent agreement is observed between the submissions near the𝐶𝐿,max state. Objective superiority over steady state RANS can be seen in terms of lack of excess outboard separation; a majority of the good quality WMLES and LB submissions predict wedge-shaped separation patterns consistent with the experimental oil flow. Differences in the onset of stall mechanism in the free-air configuration for𝛼 >20◦is reported with two distinct topologies observed. Topology A is characterized by the onset of corner-flow separation which progressively grows to produce a pitch break in free-air with an angle of attack increase from𝛼=20.55◦to𝛼=21.47◦+𝜖where𝜖is a small perturbation (varying between submissions and likely to be within±0.3◦). Topology Bis characterized by boundary layer weakness emanating from the inboard side of the wing-pylon juncture substantially larger than any weakness in the wing-body juncture (due to corner-flow);submissions in this category do not show any tendency for occurrence of a pitch break for the free-air configuration within the vicinity of𝛼=21.47◦. The in-tunnel simulations submitted by3 participants using different discretizations, grids and closure models show excellent agreement with the experiment in terms of a) integrated loads, b) surface flow-topology, and c) mechanism for the onset of inboard stall. Further evidence is provided to demonstrate both qualitative and quantitative superiority of all 3 WMLES submissions over a single steady state RANS submission to the workshop.

TTT↗

Langley's two-dimensional research facilities: Capabilities and plans

The current capabilities and the forthcoming plans for Langley's two-dimensional research facilities are described. The characteristics of the Langley facilities are discussed in terms of Reynolds number, Mach number, and angle-of-attack capabilities. Comments are made with regard to the approaches which have been investigated to alleviate typical problem areas such as wall boundary effects. Because of the need for increased Reynolds number capability at high subsonic speeds, a considerable portion of the paper deals with a description of the 20 by 60 cm two-dimensional test section of the Langley 0.3 meter transonic cryogenic tunnel which is currently in the calibration and shakedown phase.

Ray, E. J.↗

Influence of Reynolds number on forebody side forces for 3.5-diameter tangent-ogive bodies

Vortex asymmetries can arise on aircraft and missile forebodies at high angles of attack and have proven difficult to simulate in the wind tunnel because of a large array of parameters that can influence the test results. One of the most important of these parameters is Reynolds number. The current report compares, for tangent-ogive forebodies with fineness ratios of 3.5, flow patterns from oil-flow photographs to features in pressure distributions. The pressure data base is then used to illustrate the development of the sectional side force coefficient along both the tangent-ogive nose and an attached cylindrical afterbody for Reynolds numbers of 0.2, 0.8 and 3.8 million, based on maximum diameter, and angles of attack of 40, 50 and 60 deg. General commments concerning the effects of Reynolds number are presented, as well as an analysis of the effects of Reynolds number on the sectional side force coefficient near and at the apex of the pointed body. All data presented are for freestream Mach numbers on the order of 0.25.

Hall, Robert M.↗

Horizontal wind estimates deterministically derived from the STS-1 entry flight date--a comparison with available meteorology data

Two wind profiles were determined from STS-1 entry flight data based on preliminary best estimate trajectory (BET). The deterministic process used in deriving the atmospheric winds requires inertial estimates of the spacecraft angle-of-attack (alpha) and side-slip angle (beta) from the BET in conjunction with some air data system measurements of the actual angles. The current orbiter air data system (OADS) provides the necessary alpha information. Two beta profiles were adopted. The first profile assumed that the spacecraft would weathervane into any prevailing wind. The second assumed a conservative side-slip history computed from measured accelerations in the spacecraft body axes. It is shown that there are no major differences between the deterministic winds computed using both methods. Further, comparisons of these winds with raw measurements from Tehachapi, California, and preliminary winds obtained from the LaRC LAIRS file and the JSC/TRW descent BET are presented.

Kelly, G. M.↗

Rotor Performance at High Advance Ratio: Theory versus Test

Five analytical tools have been used to study rotor performance at high advance ratio. One is representative of autogyro rotor theory in 1934 and four are representative of helicopter rotor theory in 2008. The five theories are measured against three sets of well documented, full-scale, isolated rotor performance experiments. The major finding of this study is that the decades spent by many rotorcraft theoreticians to improve prediction of basic rotor aerodynamic performance has paid off. This payoff, illustrated by comparing the CAMRAD II comprehensive code and Wheatley & Bailey theory to H-34 test data, shows that rational rotor lift to drag ratios are now predictable. The 1934 theory predicted L/D ratios as high as 15. CAMRAD II predictions compared well with H-34 test data having L/D ratios more on the order of 7 to 9. However, the detailed examination of the selected codes compared to H-34 test data indicates that not one of the codes can predict to engineering accuracy above an advance ratio of 0.62 the control positions and shaft angle of attack required for a given lift. There is no full-scale rotor performance data available for advance ratios above 1.0 and extrapolation of currently available data to advance ratios on the order of 2.0 is unreasonable despite the needs of future rotorcraft. Therefore, it is recommended that an overly strong full-scale rotor blade set be obtained and tested in a suitable wind tunnel to at least an advance ratio of 2.5. A tail rotor from a Sikorsky CH-53 or other large single rotor helicopter should be adequate for this exploratory experiment.

Harris, Franklin D.↗

Emergency Flight Control of a Twin-Jet Commercial Aircraft using Manual Throttle Manipulation

The Department of Homeland Security (DHS) created the PCAR (Propulsion-Controlled Aircraft Recovery) project in 2005 to mitigate the ManPADS (man-portable air defense systems) threat to the commercial aircraft fleet with near-term, low-cost proven technology. Such an attack could potentially cause a major FCS (flight control system) malfunction or other critical system failure onboard the aircraft, despite the extreme reliability of current systems. For the situations in which nominal flight controls are lost or degraded, engine thrust may be the only remaining means for emergency flight control [ref 1]. A computer-controlled thrust system, known as propulsion-controlled aircraft (PCA), was developed in the mid 1990s with NASA, McDonnell Douglas and Honeywell. PCA's major accomplishment was a demonstration of an automatic landing capability using only engine thrust [ref 11. Despite these promising results, no production aircraft have been equipped with a PCA system, due primarily to the modifications required for implementation. A minimally invasive option is TOC (throttles-only control), which uses the same control principles as PCA, but requires absolutely no hardware, software or other aircraft modifications. TOC is pure piloting technique, and has historically been utilized several times by flight crews, both military and civilian, in emergency situations stemming from a loss of conventional control. Since the 1990s, engineers at NASA Dryden Flight Research Center (DFRC) have studied TOC, in both simulation and flight, for emergency flight control with test pilots in numerous configurations. In general, it was shown that TOC was effective on certain aircraft for making a survivable landing. DHS sponsored both NASA Dryden Flight Research Center (Edwards, CA) and United Airlines (Denver, Colorado) to conduct a flight and simulation study of the TOC characteristics of a twin-jet commercial transport, and assess the ability of a crew to control an aircraft down to a survivable runway landing using TOC. The PCAR project objective was a set of pilot procedures for operation of a specific aircraft without hydraulics that (a) have been validated in both simulation and flight by relevant personnel, and (b) mesh well with existing commercial operations, maintenance, and training at a minimum cost. As a result of this study, a procedure has been developed to assist a crew in making a survivable landing using TOC. In a simulation environment, line pilots with little or no previous TOC experience performed survivable runway landings after a few practice TOC approaches. In-flight evaluations put line pilots in a simulated emergency situation where TOC was used to recover the aircraft, maneuver to a landing site, and perform an approach down to 200 feet AGL. The results of this research, including pilot observations, procedure comments, recommendations, future work and lessons learned, will he discussed. Flight data and video footage of TOC approaches may also be shown.

Cole, Jennifer H.↗

CFD Simulations in Support of Shuttle Orbiter Contingency Abort Aerodynamic Database Enhancement

Modern Computational Fluid Dynamics (CFD) techniques were used to compute aerodynamic forces and moments of the Space Shuttle Orbiter in specific portions of contingency abort trajectory space. The trajectory space covers a Mach number range of 3.5-15, an angle-of-attack range of 20deg-60deg, an altitude range of 100-190 kft, and several different settings of the control surfaces (elevons, body flap, and speed brake). Presented here are details of the methodology and comparisons of computed aerodynamic coefficients against the values in the current Orbiter Operational Aerodynamic Data Book (OADB). While approximately 40 cases have been computed, only a sampling of the results is provided here. The computed results, in general, are in good agreement with the OADB data (i.e., within the uncertainty bands) for almost all the cases. However, in a limited number of high angle-of-attack cases (at Mach 15), there are significant differences between the computed results, especially the vehicle pitching moment, and the OADB data. A preliminary analysis of the data from the CFD simulations at Mach 15 shows that these differences can be attributed to real-gas/Mach number effects. The aerodynamic coefficients and detailed surface pressure distributions of the present simulations are being used by the Shuttle Program in the evaluation of the capabilities of the Orbiter in contingency abort scenarios.

Papadopoulos, Periklis E.↗

Transonic stability and control characteristics of a 0.015-scale (remotely controlled elevon) model 44-0 of the space shuttle orbiter tested in the NASA/LaRC 8 foot TPT (LA62)

The objective of the test was to generate a detailed aerodynamic data base which can be used to substantiate the aerodynamic design data book for the current shuttle orbiter configuration. Special attention was directed to definition of nonlinear aerodynamic characteristics by taking data at small increments in Mach number, angle of attack, and elevon position. Six-component aerodynamic force and moment and elevon position data were recorded over an angle-of-attack range from -4 deg to 20 deg, at angles of sideslip of 0 deg and 2 deg. The test Mach numbers were from 0.35 to 1.20. The Reynolds number for most of the test was held at a constant 3.5 million per foot.

Gamble, J. D.↗

Development of a Numeric Predictor-Corrector Aerocapture Guidance for Direct Force Control

Direct force control, where the angle of attack and sideslip angle are modulated, has been proposed as an alternative to bank angle control for aero-assist maneuvers. This paper reimplements the current state-of-the-art aerocapture guidance for bank angle control, Fully Numeric Predictor-corrector Aerocapture Guidance (FNPAG), for direct force control. The optimal control theory underlying the structure of FNPAG is shown to not be applicable to the direct force control approach. Several solution structures for the longitudinal channel are compared by simulating dispersed three-degree-of-freedom trajectories for a reference mission consisting of a low lift-to-drag vehicle and a highly elliptical, 1-sol target orbit around Mars. The equations of motion for the lateral channel are derived, and a controller is designed to target a specified orbital plane. Finally, a Monte Carlo is used to demonstrate the performance of the new guidance.

Matz, Daniel A.↗

Non-Repudiation for Drone-Related Data

Concepts for the management of Uncrewed Aircraft Systems (UAS) at scale rely on the exchange of data amongst multiple stakeholders. Even as these concepts vary across nations and industries, the movement of data between entities is a common theme. While there is universal agreement on the necessity of appropriate cybersecurity measures to address data communication, there has been minimal focus on the feasibility of implementing non-repudiation solutions for UAS systems. This means that data exchanged in support of UAS operations are open to “attack” via parties that may deny sending or receiving certain data, which can weaken the effectiveness and acceptability of these systems. This paper highlights the current and future need for non-repudiation, supported by references to multiple international organizations, and an approach to implementing non-repudiation leveraging open standards.

drone↗

Low-subsonic stability and control characteristics of a 0.015-scale remotely controlled elevon model (44-0) of the space shuttle orbiter in the Langley Research Center low turbulence pressure tunnel (LA61B)

A Langley-built 0.015-scale SSV orbiter configuration with remote independently operated left and right elevon surfaces was tested in the NASA/Langley Research Center Low Turbulence Pressure Tunnel. A detailed aerodynamic data base was obtained for the current shuttle orbiter configuration. Special attention was directed to definition of Reynolds number effects on nonlinear aerodynamic characteristics of the orbiter. Small increments in angle of attack, sideslip, and elevon/aileron position were studied in order to better define areas where nonlinearities may occur. Force and moment, and elevon position data were recorded over an angle of attack range -2 deg to 20 deg at angles of sideslip of 0 deg , + or - 2 deg, and + or - 4 deg. Tests were also made over an angle of sideslip range of -6 deg to 6 deg at selected angles of attack and elevon/aileron position. The test Mach numbers were from 0.15 to 0.30 at Reynolds numbers from 2.0 to 13.5 million per foot.

Source record↗

A novel potential/viscous flow coupling technique for computing helicopter flow fields

The primary objective of this work was to demonstrate the feasibility of a new potential/viscous flow coupling procedure for reducing computational effort while maintaining solution accuracy. This closed-loop, overlapped velocity-coupling concept has been developed in a new two-dimensional code, ZAP2D (Zonal Aerodynamics Program - 2D), a three-dimensional code for wing analysis, ZAP3D (Zonal Aerodynamics Program - 3D), and a three-dimensional code for isolated helicopter rotors in hover, ZAPR3D (Zonal Aerodynamics Program for Rotors - 3D). Comparisons with large domain ARC3D solutions and with experimental data for a NACA 0012 airfoil have shown that the required domain size can be reduced to a few tenths of a percent chord for the low Mach and low angle of attack cases and to less than 2-5 chords for the high Mach and high angle of attack cases while maintaining solution accuracies to within a few percent. This represents CPU time reductions by a factor of 2-4 compared with ARC2D. The current ZAP3D calculation for a rectangular plan-form wing of aspect ratio 5 with an outer domain radius of about 1.2 chords represents a speed-up in CPU time over the ARC3D large domain calculation by about a factor of 2.5 while maintaining solution accuracies to within a few percent. A ZAPR3D simulation for a two-bladed rotor in hover with a reduced grid domain of about two chord lengths was able to capture the wake effects and compared accurately with the experimental pressure data. Further development is required in order to substantiate the promise of computational improvements due to the ZAPR3D coupling concept.

Summa, J. Michael↗

Status of the variable diameter centerbody inlet program

The Variable Diameter Centerbody (VDC) inlet is an ongoing research program at LeRC. The VDC inlet is a mixed compression, axisymmetric inlet that has potential application on the next generation supersonic transport. This inlet was identified as one of the most promising axisymmetric concepts for supersonic cruise aircraft during the SCAR program in the late 1970's. Some of its features include high recovery, low bleed, good angle-of-attack tolerance, and excellent engine airflow matching. These features were demonstrated at LeRC in the past by the design and testing of fixed hardware models. A current test program in the LeRC 10' x 10' Supersonic Wind Tunnel (SWT) will attempt to duplicate these features on model hardware that actually incorporates a flight-like variable diameter centerbody mechanism.

Saunders, John D.↗

Euler/Navier-Stokes flow computations on flexible configurations for stability analysis

Longitudinal dynamic stability derivatives required for design of aircraft are computed by using the state-of-the-art numerical methods for wing-body configurations. The flow is modeled using the Euler/Navier-Stokes equations with turbulence models and solved using an efficient finite-difference scheme suitable for patched structured grids. Computations are made at a flow regime that is beyond the limits of the current linear methods mostly used for computing stability derivatives. Flow conditions include shockwaves and viscous dominated vortical flows. Effect of Mach number and angle-of-attack on stability derivatives are demonstrated for a typical wing-body configuration. For the same configuration the effects of wing flexibility on the magnitude and phase angles of stability derivatives are also demonstrated.

Guruswamy, G.↗