Search NASA⌕ Search

SEARCH · Search NASA

Results for “digital Image correlation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Additively Manufactured Strain Sensing for Nuclear Reactor Applications

Real-time monitoring of materials in harsh environments is a crucial technique towards reducing innovation time in nuclear systems. The successful measurement of real time, in-situ strain measurements during nuclear reactor operation requires innovative sensing solutions, including novel sensing strategies as well as advanced sensor design, manufacturing, and materials selection. In this paper, we will discuss two primary strategies for in-situ strain measurement strategies: additively manufactured (AM) capacitive strain gauges (CSGs) and digital image correlation (DIC). Current commercial strain gauges have limited applications in reactors due to the harsh operating conditions and non-trivial attachment strategies (i.e., welding, epoxy-adhesive) that can affect both the sensing performance and the underlying substrate under testing. AM CSGs are a viable solution as they have a low profile, low hysteresis, and wireless sensing integration capabilities that will enhance nuclear sensing technologies. In this work, the mechanical and thermal performance of the AM CSGs were tested up to 300 °C using ASTM standardized testing procedures to simulate the temperatures found in existing light water reactors. The AM CSGs had a similar performance across multiple samples which correlates to analytical models. This work leads towards the development of CSGs designed for higher temperatures and additional environmental factors found in Generation-IV reactors. Non-contact sensors, such as DIC, offer a less destructive way to measure deformation of materials when compared to alternative methods of in-situ strain determination, such as weldable strain gauges. However, DIC requires high contrast surfaces, which often relies on the implementation of artificial patterns. Using traditional splatter techniques to fabricate these patterns have limitations, including poor surface adhesion and reproducibility. In this work, AM fabrication techniques were implemented to avoid such limitations. Accordingly, aerosol jet printing (AJP) was used to print small scale periodic patterns of silver on stainless steel and aluminum tensile specimens. DIC was employed to monitor strain (up to 1100 µe) during temperature cycling from 23-600 °C. The results validated the use of AJP to better control pattern parameters for small fields of view applications at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A complete grain-level assessment of the stress-strain evolution and associated deformation response in polycrystalline alloys

Polycrystalline alloys are used pervasively across structural applications contingent upon extensive experimental testing. A statistically representative number of tests are required to expose the variability in the material's performance, as a result of non-uniform microstructures and associated micromechanical fields. In a more direct means of capturing this pertinent information, multi-modal experimental techniques are presented to measure and track the complete micromechanical state, evolving during loading, of each and every grain within the regions of interest. Specifically, a combination of high-energy X-ray diffraction microscopy and digital image correlation coupled with electron backscatter diffraction are conducted on a specimen for each of the alloys, Haynes 282 and Ti7Al. The results of the multi-modal analysis definitively demonstrate that the degree of heterogeneity increases with deformation level and is used to assess the number of grains necessary for a representative volume element description of the stress state for each of these materials. Moreover, higher resolution imaging is used for identification of the slip system activity and subsequently used to study slip transmission events. An accurate knowledge of the resolved shear stress in adjacent grains (grain interactions) is demonstrated to be a key descriptor of the slip transmission events.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A method for characterization of multiple dynamic constitutive parameters of FRCs

We propose a method to measure multiple dynamic material constitutive parameters of unidirectional fiber reinforced composites (FRCs) in a single experiment. Dynamic short-beam shear (DSBS) experiments were performed on a modified Kolsky compression bar, with integration of high-speed imaging and digital image correlation (DIC). The unidirectional FRCs investigated were S-2 glass fiber reinforced matrix of TGDDM-Jeffamine® D230 with monoamine functionalized partially reacted substructures (mPRS) and commercially available SC-15. Analytical solutions of normal and shear strains of a composite beam were derived based on Timoshenko beam theory, assuming material to be transversely isotropic and have different moduli in tension and compression in each principle material orientation. Tensile and compressive moduli were inversely computed through monitoring normal strain slope when specimen was constantly loaded at a speed of ~7.3 m/s within a small deflection. Non-linear shear stress-strain behavior of the composite was described via Ramberg–Osgood equation. Finite element (FE) analysis was conducted in ABAQUS, simultaneously defining via user subroutine UMAT the transverse isotropy of material, bi-modulus constitutive model, and non-linear shear stress-strain relation. The method proposed in this work was validated by comparing strain distributions computed by FE model and DIC measurements. Comparing with traditional dynamic tensile, compressive, and shear experiments on FRCs, this method significantly simplifies the specimen preparation and design of complicated gripping fixtures for multiple experiments. Here, systematic errors resulting from variations of specimen geometry and dimension, loading direction, and instrumentation are reduced, thereby providing compatible data for numerical studies on impact behavior of composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Full-Field Strain Measurement Integrated with Two Dimension Regression Analysis to Evaluate the Bi-Modulus Elastic Properties of Isotropic and Transversely Isotropic Materials

Background: Measuring the physical properties of shale is critical for optimizing engineering activities such as geothermal energy generation and hydraulic fracturing. Shale is a transversely isotropic material. Furthermore, this material can also include micro and macro cracks at different locations and orientations that cause it to behave differently under tensile or compressive loading. Objective: In this work, a combined experimental–numerical approach is proposed to evaluate the bi-modulus elastic properties of isotropic and transversely isotropic materials. Methods: Full-field strain measurements for a circular disk under diametral compression are integrated with a regression analysis technique to evaluate the elastic properties of bi-modulus materials subjected to tensile and compressive loads using two loading configurations on the same specimen. Digital Image Correlation (DIC) is used to measure the full-field strains. Subsequently, in the case of an isotropic material, a linear least-squares approach is utilized to process the experimentally determined strains in conjunction with analytical expressions of the stress fields (in terms of far-field loading) to determine the elastic modulus E, the shear modulus G, and the Poisson’s ratio $v$. In the case of a transversely isotopic material, such as shale, a finite element model is implemented to determine the stress fields (again in terms of far-field loading), which is followed by repeating the previous regression analysis in an iterative process to estimate the elastic parameters. Results: The results show that the proposed technique successfully provides a complete set of elastic properties as a function of both the loading condition and the principal material directions. The technique is validated by measurements on a known isotropic material and then applied to determine the properties of shale. Conclusion: In this work, the proposed approach is successfully used to calculate the bi-modulus elastic response of poly(methyl meth- acrylate) (PMMA) and shale. As expected, PMMA exhibits an isotropic response with no bi-modulus effect, however, shale exhibits both transverse isotropy and a bi-modulus effect. Therefore, this approach holds promise for investigating the elastic properties of materials like rocks and fiber-reinforced composite laminates as functions of the principal material directions and the loading conditions.

42 ENGINEERING↗
DOE OSTI2022

Development of grain-scale slip activity and lattice rotation fields in Inconel 718

Using a combination of in-situ high-resolution digital image correlation (HR-DIC), Heaviside-DIC method (H-DIC), and crystal plasticity finite element (CPFE), we investigate the evolution of intragranular lattice rotations and slip activity during monotonic and cyclic loading in a high performance, polycrystalline face centered cubic material. The CPFE employs a quasi-3D model microstructure, which is a highly resolved mirror representation of the experimental in-situ test sample. In agreement, the measurements and calculations reveal that most grains, regardless of their size and lattice orientation, develop intragranular lattice rotation gradients that span the grain. For a small cluster of grains on the deformed material, we perform HR-DIC analysis of slip lines to demonstrate agreement in the active slip systems and changes in this local slip activity across the individual grains. The combined analysis reveals that deforming grains are divided into sub-granular regions of uniform lattice rotation and these regions are most often associated with only one or two active slip systems. The gradient lines that divide them correspond to changes in the predominant slip system. The model is used to examine the evolution of intragranular lattice rotation in a single fully reversed tension-compression cycle. The calculations indicate that intragranular gradients intensify during the reverse loading path as nearest neighboring regions appear to shed lattice rotation, increasing the lattice rotation in some regions, while shutting down rotation in neighboring regions. So these findings provide insight into the irreversible changes that develop within deforming grains at the scale of the grain, particularly the heterogeneous development of intragranular lattice rotation in early stages of deformation, which could serve as precursors to localization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Geophysical Signatures of Crack Network Coalescence in Rocks at Multiple Length Scales

The main goal of the research project was to identify the geophysical signatures of fracture growth in natural rocks by utilizing novel geophysical techniques. The research objectives were to (a) investigate the potential for geophysical methods to determine when cracks initiate, the types and locations of propagated cracks, and the coalescence of networks of cracks in natural rocks at multiple scales, (b) determine how damage at the microscale evolved into damage at the macroscale and then link the microscopic and macroscopic observations, (c) quantify crack coalescence in rocks under realistic stress conditions using coupled mechanical-geophysical-optical visualization, and (d) identify the precursors in geophysical signals to crack coalescence. The following research thrusts were explored to achieve the research objectives: (1) uniaxial compression testing of rock specimens with and without a set of pre‐existing flaws and (2) triaxial compression testing of natural rock specimens. These thrusts allowed for exploring fracturing in rocks under realistic in situ environments and at multiple scales. This project provided educational opportunities for nine graduate and undergraduate students and resulted in 27 peer-reviewed publications. This first research thrust focused on investigating the micromechanics of fractures in rocks through uniaxial compression testing combined with advanced geophysical and imaging techniques, specifically acoustic emission (AE) monitoring, ultrasonic imaging, and 2-dimensional Digital Image Correlation (2D-DIC). By examining damage processes under time-independent and time-dependent loading conditions, insights into damage localization, crack initiation, and fracturing mechanisms were gained. It was observed that the AE signals and the strain-based measurements directly reflect the state of damage in the rock specimen and could be used to identify the cracking levels, such as the crack initiation (CI) and crack damage (CD), and the mode of deformation. A novel calibration apparatus was developed to enhance the accuracy of AE sensors, allowing for the estimation of key parameters such as magnitude, source dimension, stress drop, and radiated seismic energy associated with the fractures. The findings highlighted significant variations in the temporal evolution of AE source parameters during the primary, secondary, and tertiary stages of creep, identifying tensile cracking as the primary deformation mode. The second research thrust focused on enhancing the understanding of fracturing processes in natural rocks through triaxial compression testing, real-time AE monitoring, and ultrasonic monitoring. We investigated the impact of various factors such as fracture propagation regimes, injection parameters, rock types, and pre-existing conditions on the hydraulic fracture (HF) behavior using scaled true-triaxially loaded specimens of Barre granite and Lyons sandstone. Custom sensor housing facilitated concurrent active and passive monitoring to analyze hydro-mechanical responses and microseismicity associated with different HF scenarios. A coupled investigation of passive microseismicity and active signal attributes permitted a detailed comprehension of the various HF processes (aseismic deformation, fracture initiation and propagation, fluid permeation, and leak-off) and their dependence on the specific rock type. The findings of this research demonstrated the effectiveness of AE monitoring techniques in providing valuable insights into the impact of various factors on the behavior and dynamics of HF processes. The advancements in monitoring techniques, offering a more thorough and precise approach, represent a significant step towards optimizing HF practices and ensuring sustainable resource extraction.

58 GEOSCIENCES↗
DOE OSTI2024

Intern Poster

Digital Image Correlation (DIC) is an optical technique that combines image registration and tracking methods for accurate two-dimensional and three-dimensional changes in images. DIC software can be used to track the contour, deformation, and strain of a sample. In the Advanced Test Reactor (ATR) at INL (Idaho National Laboratory) there exists a small working window of samples that can become irradiated. Hundreds of graphite disks called piggybacks have undergone this irradiation as part of the Advanced Reactor Technologies (ART) program. After irradiation, it is desirable to understand the change in tensile strength as a function of dose. Due to the limited space in the ATR, typical dog bone tensile tests reduce the number of graphite samples from hundreds to tens. However, there does exist an ASTM standard, D8289, which uses disc compression of graphite to estimate the tensile strength of the specimen with the Brazilian Disk test fixture. While only used as an estimate, which is typically off by a third, it is the purpose of this study to identify how to amend D8289 to remove the word "estimate" with the help of DIC.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Toughness of Interlocking Metasurfaces

Interlocking metasurfaces (ILMs) are arrays of autogenous latching unit cells patterned across a surface. These create structural joints similar to bioinspired suture joints but patterned over a 2D surface rather than a 1D seam. This enables ILMs to be an alternative to conventional joining technologies such as bolts, welds, and adhesives. However, compared to conventional joining methods, relatively little is known of the engineering considerations for designing structural ILMs. Herein, the interfacial toughness of an archetypal ILM is examined for the first time. Under the conditions studied here, the ILM is substantially tougher than the material from which it is made, in this case, exhibiting up to a 50% increase in interfacial crack initiation energy over the solid base material, a photocured 3D‐printed polymer. Through experimental tests using in‐situ digital image correlation along with complementary computational analyses, the mechanism of toughening in the ILM structure and the origins of toughness anisotropy are revealed. The increase in toughness is associated with cross‐cell interactions, that is, load‐sharing across unit cells, which give rise to a finite process zone length with different effective material properties. In this way, ILM toughening is analogous to crack blunting in ductile materials or fiber bridging in composites; yet here, the ILM is composed of a single‐phase base material and so the architected toughening is geometric in nature and hence amenable to future topological optimization.

fracture↗
DOE OSTI2023

The Role of Transition Metals on Chemo-Mechanical Instabilities in Prussian Blue Analogues For K-Ion Batteries: The Case Study on KNHCF Versus KMHCF

Prussian blue analogues (PBAs) cathodes can host diverse monovalent and multivalent metal ions due to their tunable structure. However, their electrochemical performance suffers from poor cycle life associated with chemo-mechanical instabilities. This study investigates the driving forces behind chemo-mechanical instabilities in Ni- and Mn-based PBAs cathodes for K-ion batteries by combining electrochemical analysis, digital image correlation, and spectroscopy techniques. Capacity retention in Ni-based PBA is 96% whereas it is 91.5% for Mn-based PBA after 100 cycles at C/5 rate. During charge, the potassium nickel hexacyanoferrate (KNHCF) electrode experiences a positive strain generation whereas the potassium manganese hexacyanoferrate (KMHCF) electrode undergoes initially positive strain generation followed by a reduction in strains at a higher state of charge. Overall, both cathodes undergo similar reversible electrochemical strains in each charge–discharge cycle. There is ~0.80% irreversible strain generation in both cathodes after 5 cycles. XPS studies indicated richer organic layer compounds in the cathode-electrolyte interface (CEI) layer formed on KMHCF cathodes compared to the KNHCF ones. Faster capacity fades in Mn-based PBA, compared to Ni-based ones, is attributed to the formation of richer organic compounds in CEI layers, rather than mechanical deformations. In conclusion, understanding the driving forces behind instabilities provides a guideline to develop material-based strategies for better electrochemical performance.

25 ENERGY STORAGE↗
DOE OSTI2021

The impact of alkali‐ion intercalation on redox chemistry and mechanical deformations: Case study on intercalation of Li, Na, and K ions into FePO 4 cathode

Abstract Batteries made of charge carriers from Earth‐crust abundant materials (e.g., Na, K, and Mg) have received extensive attention as an alternative to Li‐ion batteries for grid storage. However, a lack of understanding of the behavior of these larger ions in the electrode materials hinders the development of electrode structures suitable for these large ions. In this study, we investigate the impact of alkali ions (Li, Na, and K) on the redox chemistry and mechanical deformations of iron phosphate composite cathodes by using electrochemical techniques and in situ digital image correlation. Na‐ion and Li‐ion intercalation demonstrate a nearly linear correlation between electrochemical strains and the state of charge and discharge. The strain development shows nonlinear dependance on the state of charge and discharge for K ions. Strain rate calculations show that K ion intercalation results in a progressive increase in the strain rate for all cycles. Li and Na intercalation induce nearly constant strain rates with the exception of the first discharge cycle of Na intercalation. When the same amount of ions are inserted into the electrode, the electrode shows the lowest strain generation upon Li intercalation compared to larger alkali ions. Na and K ions induce similar volumetric changes in the electrode when the state of charge and discharge is around 30%. Although the electrode experiences larger absolute strain generation at the end of the discharge cycles upon Na intercalation, strain rates were found to be greater for K ions. Potential‐dependent behaviors also demonstrate more sluggish redox reactions during K intercalation, compared to Li and Na. Our quantitative analysis suggests that the strain rate, rather than the absolute value of strain, is the critical factor in amorphization of the crystalline electrode.

25 ENERGY STORAGE↗
DOE OSTI2022

Experimental study of compaction localization in carbonate rock and constitutive modeling of mechanical anisotropy

Abstract Sedimentary rocks are inherently anisotropic and prone to strain localization. While the influence of rock anisotropy on the brittle/dilative regime has been studied extensively, its influence on the ductile/compactive regime is much less explored. This paper discusses the anisotropic behavior of a high‐porosity carbonate rock from central Europe (the Maastricht Tuffeau). A set of triaxial tests with concurrent x‐ray tomography has been performed at different confining pressures. The anisotropic characteristics of this rock have been investigated by testing samples cored at different inclinations of the bedding, thus revealing non‐negligible effects of the coring direction on yielding and compaction behavior. Specifically, samples cored perpendicular to bedding display higher strength and longer stages of post‐yielding deformation before manifesting re‐hardening. Despite such alterations of the inelastic response, Digital Image Correlation has revealed that the strain localization mode is independent of the coring direction, thus being primarily affected by the confinement level. To capture the observed interaction between material anisotropy and compaction behavior at the continuum‐scale, an elastoplastic constitutive law has been proposed. For this purpose, a set of tensorial bases has been introduced to replicate how the oriented rock fabric modulates the yielding and plastic flow characteristics of the material. The analyses show that the impact of the coring direction on yield function and plastic flow rule is fundamentally different, thus requiring the use of distinct projection strategies (a strategy here defined heterotopic mapping). The performance of the model, studied through parametric analyses and by calibrating the experimental results, illustrates the improved capability of the proposed constitutive approach when applied to strongly anisotropic porous rocks.

Shahin, Ghassan↗
DOE OSTI2021

Calibration of elastoplastic constitutive model parameters from full-field data with automatic differentiation-based sensitivities

Here, we present a framework for calibration of parameters in elastoplastic constitutive models that is based on the use of automatic differentiation (AD). The model calibration problem is posed as a partial differential equation-constrained optimization problem where a finite element (FE) model of the coupled equilibrium equation and constitutive model evolution equations serves as the constraint. The objective function quantifies the mismatch between the displacement predicted by the FE model and full-field digital image correlation data, and the optimization problem is solved using gradient-based optimization algorithms. Forward and adjoint sensitivities are used to compute the gradient at considerably less cost than its calculation from finite difference approximations. Through the use of AD, we need only to write the constraints in terms of AD objects, where all of the derivatives required for the forward and inverse problems are obtained by appropriately seeding and evaluating these quantities. We present three numerical examples that verify the correctness of the gradient, demonstrate the AD approach's parallel computation capabilities via application to a large-scale FE model, and highlight the formulation's ease of extensibility to other classes of constitutive models.

42 ENGINEERING↗
DOE OSTI2025

Control of machining-induced residual stress via tool geometry and process parameter modification

Distortion generated in machined, monolithic, thin-walled aerospace components due to residual stresses leads to significant material and economic waste in the manufacturing industry. Inherent residual stress (IRS) present in stock materials combines with machining-induced residual stress (MIRS) to influence the final machined part distortion. It is hypothesized that MIRS can be controlled, based on the part geometry, through deliberate cutting tool geometry and process parameter modifications to negate the effect of IRS on distortion, consequently resulting in distortion-free parts. A finite element (FE) orthogonal cutting model is developed to study how tool geometry and process parameters influence machining-induced residual stress (MIRS). Orthogonal cutting experiments are performed on Al 7075-T651 samples to measure cutting forces and MIRS. A cutting force dynamometer is used to measure forces during cutting and a novel digital image correlation (DIC) based hole drilling technique is employed to measure the near-surface residual stress (RS) in the cut samples. These data are subsequently utilized to validate the FE prediction model. Various cases of cutting simulations involving different depths of cut, tool tip radii, and rake angles are performed to study their effects on RS. Similar to prior literature, increasing the depth of cut, tool tip radius, or rake angle is found to promote the formation of near-surface tensile stresses. The competing effects of material plowing and temperature are shown to determine the type of RS at the end of the cut. Moreover, a window of variation of RS (up to ± 400 MPa) is estimated within the given range of conditions, allowing for the control of MIRS through tool and process modification.

Mathews, Ritin [ORNL] (ORCID:0000000301440828)↗
DOE OSTI2022

Micromechanics of Fracture Propagation During Multistage Stress Relaxation and Creep in Brittle Rocks

Time-dependent rock deformation caused by the initiation and growth of fractures leads to the weakening of the rock mass. Understanding the fracturing mechanisms involved in the time-dependent behavior in brittle rocks is very important and to achieve this goal, a systematic series of three types of experiments was performed on double-flawed prismatic Barre granite specimens under unconfined compression. The first series aimed to identify the failure mechanism in the short-term failure mode under monotonic loading, the, second series involved multistage relaxation (constant strain) experiments to analyze the damage at different strain levels, and the third series explored the fracture propagation under multistage creep (constant load) experiments. The spatial and temporal evolution of cracking mechanisms were evaluated using the acoustic emission (AE) and two-dimensional digital image correlation (2D-DIC) techniques to observe the whole crack growth process as well as the accumulated inelastic strain at the specified region of interest. Results suggest that in the case of multistage creep experiments, the time to failure was less compared to the multistage relaxation, when loaded above the crack damage threshold (CD) estimated from the monotonic testing. Furthermore, the frequency magnitude distribution of the AE events generated in the three loading conditions followed the Gutenberg Richter model. A relatively lower b-value was obtained for the creep experiments, indicative of high energy AE events and faster crack growth. In addition, the AE and DIC results also revealed high evolution of tensile cracks at-different stages of creep and relaxation compared to shear and mixed-mode cracks.

58 GEOSCIENCES↗
DOE OSTI2024

Temporal and Spatial Evolution of Non-Elastic Strain Accumulation in Stanstead Granite During Brittle Creep

Understanding the long-term behavior of brittle rocks requires fundamental consideration of time-dependent strain evolution and brittle creep processes. Previous studies have evaluated sub-critical crack growth during time-dependent deformation and damage evolution in brittle rocks; however, there is an incomplete knowledge of how damage evolves spatially and temporally within the body of intact rocks, where distributed regions of damage interact and coalesce during creep. This paper presents laboratory research focusing on evaluating brittle creep damage processes in Stanstead granite (SG) using 2-dimensional digital image correlation (2D-DIC). In the laboratory, the prismatic SG specimens were loaded beyond an estimated Crack Damage stress threshold (CD) level and then maintained a constant stress to initiate the creep process. DIC was used to characterize full-field spatiotemporal strain evolution, which was then interpreted in the context of local regions of “damage”, determined according to a strain-based criterion. Here, a method was proposed for identifying “existing” and “new” damage regions over specified intervals during the test, followed by spatial clustering of these regions to assess their spatiotemporal evolution. The clustering analysis results demonstrated the extension of existing damage regions was the main damage process during brittle creep, which is consistent with existing models of sub-critical crack growth. In addition, temporal analysis of tensile and shear strains on a point-by-point basis revealed both new damage formation and the strain concentration within existing damaged regions significantly contribute to overall specimen strain during primary creep. In contrast, during secondary creep, increases in specimen deformation are influenced by the accumulation of strains within already damaged regions.

58 GEOSCIENCES↗
DOE OSTI2022

Physics-Informed and Data-Driven Prediction of Residual Stress in Three-Dimensional Machining

Efficient and reliable prediction of machining-induced residual stress (RS) is a key requirement for truly integrated computational materials engineering (ICME). Currently available process modeling approaches, including empirical, analytical, and numerical methodologies lack predictive power and require substantial calibration and validation data. Moreover, most model-based approaches consider only two-dimensional (2D) (i.e., orthogonal), cutting processes. Meanwhile, industrial processes such as milling, turning, and drilling are inherently three-dimensional (3D). The present work attempts to bridge the gap between 2D and 3D through careful consideration of the process physics, including geometric, kinematic, and size-effect constraints to realize robust prediction of how RS develops in 3D machining. Using a novel in-situ experimental technique and digital image correlation (DIC) to determine equivalent Hertzian contact widths, contact pressures, and friction coefficients, the proposed methodology leverages a discretized conversion algorithm that includes multi-pass shakedown effects. This paper presents a semi-analytical model to predict machining-induced RS in 3D turning operations, which are used representatively for 3D processes more generally. Rather than follow a ‘brute force’ 3D FEM approach or conduct countless experiments to train a purely data-driven machine learning algorithm, the proposed approach builds on previous 2D modeling work. Through careful consideration of the process physics, including complex geometry/kinematic considerations of 3D turning, the authors demonstrated an experimentally calibrated approach, as well as validation based on published RS data. Model predictions and previously published measurement data of RS depth profiles for turning of Inconel 718 were compared for a range of process parameters. Correlation between the proposed 3D model and validation data was found to be within the margin of experimental error for most conditions. The proposed model appears to capture the overall behavior of 3D RS depth profiles with acceptable accuracy, particularly the key metrics of near-surface stress, peak stress magnitude and location, as well as overall stress profile depth. This report presents a physics-informed, data-driven approach for efficient calibration of a 2D model for machining-induced RS through DIC analysis of in-situ characterized subsurface displacement fields.

42 ENGINEERING↗
DOE OSTI2025

The Ductility of 49Fe-49Co-2V Soft Magnetic Alloy Bar: Surface Effects and Test Methods

The tensile ductility of 49Fe-49Co-2V (Hiperco® 50A) bar was investigated in both as-received and heat-treated conditions. The as-received/machined specimens exhibit very low ductility compared to samples where heat treatment was the final step prior to testing. Microstructural characterization showed that internal residual strain from bar processing and, most importantly, surface machining damage, cause lower elongation in the as-received material. Because fracture of this intermetallic alloy initiates at the surface, it is particularly susceptible to surface machining damage, i.e., the near-surface region has already exhausted most of its ability to accumulate tensile strain. During heat treatment, the internal residual strain and near-surface machining damage are eliminated and ductility is improved, despite a higher degree of crystallographic ordering in the heat-treated condition (which typically lowers ductility). Furthermore, if machining is again performed after heat treatment, the material again exhibits brittle behavior, even with only light touch-up machining passes. Here, in this work, methods of tensile strain measurement were investigated, namely conventional knife-edge extensometry and noncontact digital image correlation (DIC) on heat-treated material. For clip-on knife-edge extensometry, the range of failure strain was 2.5-5.5% for heat-treated Hiperco. For noncontact methods, ductility up to 7% was observed. The results highlight the tendency for the alloy to fail at surface imperfections, even those produced by application of the extensometer itself. Noncontact laser extensometry is recommended for determining the intrinsic ductility of the alloy. A method of laser surface modification was developed which increased ductility by ~ 100% compared to unmodified samples. The high cooling rates achieved during laser surface processing can bypass the ordering reaction and produce a ductile disordered structure at the surface that exhibits ductile fracture characteristics.

EBSD↗
DOE OSTI2025

Experimental Evaluation of Interfacial Bonding Strength Between 304 Stainless Steel Substrate and Electrodeposited Nickel Coating Using Mesoscale Mechanical Testing Methods

Electrodeposition is a commonly used method for depositing a metal layer on a metallic substrate, to provide a decorative finish or for functional purposes including wear and corrosion resistance. The interfacial bonding strength is a critical factor in determining the quality of electrodeposition, as it ensures the adhesion of the deposited layer to the substrate. Despite its importance, there has not previously been a suitable mechanical testing method to quantitatively characterize the bonding strength between the electrodeposited layers and the substrate, due to the high strength of the materials and to restrictions imposed by the geometry (due to the small thickness of the plating layer) to manufacture tensile bars. In this study, we introduce a novel mesoscale mechanical testing method to overcome these limitations. This technique was applied to assess the bonding strength between a 304 stainless steel (SS) substrate and electrodeposited nickel with three different plating formulae (nickel sulfamate, Watts bath, and hard nickel). The thickness of the pure nickel coatings achieved for each of the three electrolyte solutions was approximately 1 mm on each side of the substrate. Mesoscale tensile bars of 1 mm length were manufactured by a femtosecond laser, with the material interface at the center of the gauge section, and then tensile-tested with digital image correlation. Further, the results proved that the electrodeposition technique is able to produce a very high bonding strength that is close to the yield strength of both the substrate material and the electrodeposited nickel layer. Additionally, in the case of the Watts bath formula, the interfacial bonding strength between the SS 304 and electrodeposited nickel can exceed that of the nickel layer. This method is expected to be useful for quantifying the interfacial bonding strength in numerous applications.

36 MATERIALS SCIENCE↗