Search NASA⌕ Search

SEARCH · Search NASA

Results for “divertors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

The effectiveness of D 2 pellet and gas injection in reducing intra-ELM tungsten erosion and heat flux in the DIII-D small angle slot divertor

Edge localized modes (ELMs) in H-mode plasmas can melt and erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes the use of D 2 pellet and gas injection for ELM mitigation on the DIII-D tokamak during the 2022 Small Angle Slot V-shaped Tungsten (W) (SAS-VW) divertor campaign, reducing W erosion and heat flux during ELMs. D α (656 nm) and WI (400.9 nm) filterscopes and Langmuir probes provide photon emission and electron density/temperature to estimate W atom erosion using the S/XB method, while surface eroding thermocouples measured ELM peak heat flux at the outer strike point (OSP). Thomson Scattering measurements of pedestal T e and n e provided input to predict W divertor erosion and heat flux during ELMs via the Free-Streaming plus Recycling Model (FSRM). While a greater D 2 mass injection rate decreased the ELM peak heat flux, the impact on W erosion was not monotonic. The average ‘large’ intra-ELM W erosion was lower for plasma shots with D 2 mass injection compared to the plasma shots without any D 2 mass injection in the SAS-VW divertor. However, plasma shots did not see significant changes in ‘large’ intra-ELM W divertor erosion as the D 2 mass injection rate increased. On average, the FSRM overestimated SAS-VW experimental intra-ELM W erosion by a factor of 6.9, but the overestimation is reduced to a factor of 3.6 with the implication of C deposition effects. Generally, experimentally measured and predicted quantities were worse for plasma shots with a lower D 2 mass injection rate and corresponding higher plasma carbon (C) impurity percentage (f C ). The discrepancies are postulated to be due to C/W material mixing, for which a simple analytic mixed-material model is presented. These results highlight the importance of incorporating and improving the robustness of a mixed-material layer model in the analysis of PFC erosion on present and future tokamak devices.

Carbon (C)↗
DOE OSTI2025

Demonstration of Super-X divertor exhaust control for transient heat load management in compact fusion reactors

Nuclear fusion could offer clean, abundant energy. However, managing the power exhausted from the core fusion plasma towards the reactor wall remains a major challenge. This is compounded in emerging compact reactor designs promising more cost-effective pathways towards commercial fusion energy. Alternative Divertor Configurations (ADCs) are a potential solution. In this work, we demonstrate exhaust control in ADCs, employing a novel method to diagnose the neutral gas buffer, which shields the target. Our work on the Mega Ampere Spherical Tokamak Upgrade shows that ADCs tackle key risks and uncertainties for fusion energy. Their highly reduced sensitivity to perturbations enables active exhaust control in otherwise unfeasible situations and facilitates an increased passive absorption of transients, which would otherwise damage the divertor. We observe a strong decoupling of each divertor from other reactor regions, enabling near-independent control of the divertors and core plasma. Our work showcases the real-world benefits of ADCs for effective heat load management in fusion power reactors.

Imaging techniques↗
DOE OSTI2022

Modeling study of divertor particle and heat flux asymmetries for EAST H-mode discharges

The BOUT++ transport code is run to study the effects of plasma drifts on the divertor out-in asymmetries (DOIAs) of particle and heat fluxes and their decay widths for EAST lower single null H-mode discharges. The diamagnetic drift seems to have no effects on the DOIAs of total particle and heat fluxes due to its divergence-free nature. However, it could significantly increase the DOIAs of peak particle and heat fluxes and the flux decay widths. The E × B drift is found to induce a large plasma flow to the divertor region, enhancing the DOIAs of both total and peak particle and heat fluxes and the flux decay widths. Both the radial and poloidal components of the E × B drift are necessary in increasing the DOIAs, however, the radial E × B drift seems to play a more important role. The effects on the DOIAs caused by both diamagnetic and E × B drifts are reversed with the reverse of toroidal magnetic field. The heat flux decay width λ q and spreading width S q are important physical and engineering parameters for the divertors and could be obtained by fitting the heat flux profiles at divertor targets. The λ q at the outer target from the simulation case with all drifts could well match with the multi-machine scaling proposed by Eich and the DOIA of λ q is in reasonable agreement with the scaling proposed by Goldston.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Mechanisms behind impurity spreading in a channeled, long-leg divertor configuration

One suggested benefit of long-leg, tightly baffled divertor configurations, a common feature included in the designs of many next-generation fusion devices, is access to a delocalized “spread” of impurity radiation along the leg, allowing for a substantial radiation region while maintaining both sufficient distance from the core to prevent pollution of the plasma fuel and avoiding local overheating of the plasma-facing materials. However, it is unclear whether this increased connection length and divertor volume afforded by the long-leg configuration is compatible with impurity transport, and whether it will enable this desired impurity radiation spread at all. Here, the SOLPS 4.3 code is used to assess the distribution of nitrogen and neon impurity radiation in a long-leg, tightly baffled divertor geometry. Further, there is a strong correspondence between the distribution of impurity radiation in the long leg and impurity recycling on the divertor side walls with both the nitrogen simulation set and the neon simulation set, suggesting that impurity spreading along these long legs is due to the interplay between the cross-field transport and associated neutralization of the impurity on the material surfaces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Demonstration of a two-dimensional divertor Thomson scattering system on DIII-D

Recent upgrades providing two-dimensional divertor Thomson scattering (DTS-2D) measurements of T e and n e during a DIII-D plasma shot and a thorough description of system components and their functionality are presented. This system expands the capabilities of the existing single divertor Floor measurement location by introducing seven additional laser beam path options in the poloidal plane, spanning major radii from 1.062 to 1.335 m. The system redirects ~1 J, 50 Hz Nd:YAG laser pulses to the new beam paths within 20 ms, stepping through each path on the divertor Floor every 200 ms during a plasma shot. The laser is redirected using an ex-vessel, fast-steering mirror to one of eight in-vessel beam paths oriented underneath the vessel tiles. Up to eleven measurement positions per beam path, from –1.35 to –1.13 m below the machine midplane, are available by dynamically refocusing the ex-vessel collection fiber array using a high-speed linear stage. As a result, current measurement positions above the divertor Shelf are retained via a hole in the fixed, in-vessel mirror, allowing laser pass through.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Novel data interpretation method for DIII-D divertor retarding field energy analyzer with 3-D particle-in-cell simulations

A novel data interpretation process that utilizes comprehensive particle-in-cell (PIC) simulations is developed for the new retarding field energy analyzer (RFEA) currently being constructed at DIII-D for the lower divertor using the Divertor Material Evaluation System. Furthermore, this probe is expected to survive a heat load of up to 100 MW/m 2 for up to 5 s and reliably measure the main ion temperature (T i ) on the divertor target ranging from 10 to 200 eV. These extreme conditions posed significant engineering limitations on the probe geometry, thus extensive validation work has been performed. The conventional fitting method for the RFEA I–V characteristics is based on a simplified 1-D model without considering the ion space charge inside the probe cavity and may not be sufficient for probes designed for the DIII-D divertor environment. In this article, a more realistic description of the particle propagation process within the RFEA cavity is achieved by including both 3-D geometric effects and ion space charge in the PIC simulations, and the capability to reconstruct the ion energy distribution functions is demonstrated with reasonable consistency.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Edge localized mode characteristics and divertor heat flux during stationary and transient phase for CFETR hybrid scenario

The study of edge localized mode (ELM) behavior, stationary heat flux and transient heat flux during the ELM crash phase is performed for a China Fusion Engineering Test Reactor (CFETR) 1 GW hybrid mode operation scenario ($R$ = 7.2 m, ${B_{\text{T}}}$ = 6.5 T, ${I_{\text{p}}}$ = 13.78 MA). Modeling and simulation start with a scenario obtained by multi-code integrated modeling on the one modeling framework for integrated tasks framework. Linear stability and nonlinear simulations of ELM dynamics are carried out using the BOUT++ six-field reduced magnetohydrodynamic module, which show a much smaller ELM energy loss (Δ ELM ~ 0.13%) compared to that of a Type-I ELM. Parametric analysis of the weak linear growth rate and small ELM energy loss characteristics shed light on physics corresponding to a grassy ELM regime for CFETR 1 GW hybrid scenario. The transient heat flux on the divertor target during this small ELM phase is investigated using BOUT++. Here we found that upstream radial transport in the scrape-off-layer (SOL) induced by small ELMs is weak, which keeps it in the drift-dominated region. However, the heat flux width is still broadened to ${\lambda _{\text{q}}}$ = 4.64 mm by the increase of separatrix temperature during ELM nonlinear evolution. The impact of transient peak heat load and ELM energy fluence on tungsten melting and net erosion rate of divertor target is evaluated for the first-time using physics-based transport that connects the pedestal with the SOL. Energy fluence caused by a single ELM pulse is below the tungsten melting limit, while tungsten erosion would exceed the material requirements. We conclude that external mitigation methods, such as divertor detachment and advanced divertor geometry are likely needed for the steady state operation of CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Analysis of the neutral fluxes in the divertor region of Wendelstein 7-X under attached and detached conditions using EMC3-EIRENE

Abstract This paper analyzes the neutral fluxes in the divertor region of the W7-X standard configuration for different input powers, both under attached and detached conditions. The performed analysis is conducted through EMC3-EIRENE simulations. They show the importance of the horizontal divertor to generate neutrals, and resolve the neutral plugging in the divertor region. Simulations of detached cases show a decrease in the number of generated neutrals compared to the attached simulations, in addition to a higher fraction of the ion flux arriving on the baffles during detachment. As the ionization takes place further inside the plasma during detachment, a larger percentage of the generated neutral particles leave the divertor as neutrals. The leakage in the poloidal and toroidal direction increases, just as the fraction of collected particles at the pumping gap. The fraction of pumped particles increases with a factor two, but stays below one percent. This demonstrates that detachment with the current target geometry, although it improves the power exhaust, is not yet leading to an increased particle exhaust.

Physics↗
DOE OSTI2020

Modeling, analysis, and code/data validation of DIII-D tokamak divertor experiments on ELM and non-ELM plasma tungsten sputtering erosion

Abstract We analyzed recent DIII-D tokamak tungsten divertor probe experiments using advanced, coupled, sputter erosion/redeposition, plasma, and surface response code packages. Modeling is done for ELMing H-mode, and L-mode plasmas, impinging on various size tungsten deposits on Divertor Material Evaluation System (DiMES) carbon probes. The simulations compute 3D, full kinetic, sub-gyromotion, impurity sputtering and transport, including changes in tungsten surface composition and response due to mixed deuterium and carbon ions irradiation. Per our analysis, ELM (edge localized mode) plasma sputtering in DIII-D mostly involves free-streaming high energy (∼500–1000 eV) D + and C +6 ions, with high near-surface plasma density. L-Mode sputtering is due to impurity sputtering (C, W) only, with lower density. All cases show complete redeposition of tungsten on the divertor, with significant redeposition on the tungsten spots themselves, and low self-sputtering. Comparison of ELM plasma gross tungsten erosion simulation results with in-situ spectroscopic data is good, as are code/data comparisons of net erosion using post-exposure Rutherford backscattering (RBS) data for the L-mode probes. The analysis, extrapolated to a full tungsten divertor, implies low net erosion and negligible plasma contamination from sputtering. These results support the use of high-Z plasma facing surfaces in ITER and beyond.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Advances in the long-pulse steady-state high beta H-mode scenario with active controls of divertor heat and particle fluxes in EAST

Since the last IAEA-Fusion Energy Conference, the Experimental Advanced Superconducting Tokamak (EAST) research program has been, in support of ITER and CFETR, focused on development in terms of the long-pulse steady-state (fully noninductive) high beta H-mode scenario with active controls of the stationary and transient divertor heat and particle fluxes. The operational domain of the steady-state H-mode plasma scenario has been significantly extended with ITER-like tungsten mono-block divertor, plasma control and heating schemes. EAST has achieved several important milestones in the development of high β p H-mode scenario and its key physics and technologies. A 60 s-scale long-pulse steady-state high β p H-mode discharge with the major normalized plasma parameters similar to the designed performance of the CFETR 1GW fusion power operation scenario has been successfully established and sustained by pure RF heating and current drive. Several feedback control schemes have been developed for a sustained detachment with good core confinement. This includes control of the total radiation power, target electron temperature, and particle flux measured using divertor Langmuir probes or a combination of the control of target electron temperature and AXUV radiation near the X point. The detachment feedback control schemes have been integrated with small-ELM regimes and high β p scenario via neon seeding, enabling a core and edge compatible integrated high-beta scenario applicable to long-pulse operations. ELM suppression has been achieved using various methods, including resonant magnetic perturbations and impurity seeding. Full suppression of ELMs by using n=4 RMPs has been demonstrated for ITER for the first time in low input torque plasmas in EAST. Finally, EAST has been operated with helium to support the ITER research requirements for the first time. For a long-pulse, high bootstrap current fraction operation, a new lower tungsten divertor with active water-cooling has been installed, along with improvements in the heating and current drive capability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Divertor-safe nonlinear burn control based on a SOLPS parameterized core-edge model for ITER

Abstract For ITER operations, the range of desirable burning-plasma regimes with high fusion power output will be restricted by various operational constraints. These constraints include the saturation of ITER’s various heating and fueling actuators such as the neutral beam injectors, the ion and electron cyclotron heating systems, the gas puffing system, and the deuterium–tritium pellet injectors. In addition to these actuator constraints, the H-mode power threshold, divertor detachment, and the heat load on the divertor targets may apply limitations to ITER’s operational space. In this work, Plasma Operation Contour (POPCON) plots that map the aforementioned constraints to the temperature-density space are used to investigate which constraints are most limiting towards accessing regimes with high fusion power output. The presented POPCON plots are based on a control-oriented core-edge model that couples the nonlinear density and energy response models for the core-plasma region with SOLPS4.3 parameterizations for conditions in the edge-plasma regions (scrape-off-layer and divertor). Using this control-oriented core-edge model, a nonlinear burn controller, which aims to regulate the plasma temperature and density in the core-plasma region, is constructed in this work. This controller is augmented with an online optimization scheme that governs the control references such that the plasma can be guided towards regimes with high fusion powers while protecting the divertor targets from dangerously high heat loads. A closed-loop simulation study illustrates the capability of this burn control scheme.

Physics↗
DOE OSTI2026

Turbulence-Driven Edge-Localized-Mode-Free High-Confinement Mode with Divertor Detachment in a Metal-Wall Tokamak

We report the first demonstration of a minute-scale, edge-localized-mode-free high-confinement plasma regime compatible with divertor partial detachment and enhanced pedestal performance in a metal-wall tokamak, the Experimental Advanced Superconducting Tokamak. This regime is enabled by a newly identified mechanism: during divertor partial detachment, reduced ionization and enhanced pumping in a closed divertor lead to less cooling of the pedestal by recycling neutrals and seeding impurities, resulting in an increased pedestal temperature gradient, which excites high-frequency broadband turbulence. Gyrokinetic simulations identify the high-frequency broadband turbulence as a temperature-gradient-driven trapped electron mode (𝜂 𝑒 -TEM), which drives outward transport of particles and heat, thereby maintaining the edge-localized-mode-free state. This pedestal regime is particularly promising for the International Thermonuclear Experimental Reactor, where the anticipated lower density gradient, reduced E×B shear, and lower collisionality in the pedestal will further facilitate 𝜂 𝑒 -TEM excitation. The achieved integrated scenario with a detached divertor and turbulence-dominated pedestal thus offers a compelling solution for managing heat loads and metal impurity sources for long-pulse high-performance operation in future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

First Evidence of Local E × B Drift in the Divertor Influencing the Structure and Stability of Confined Plasma near the Edge of Fusion Devices

The structure of the edge plasma in a magnetic confinement system has a strong impact on the overall plasma performance. Here we uncover for the first time a magnetic-field-direction dependent density shelf, i.e., local flattening of density radial profile near the magnetic separatrix, in high confinement plasmas with low edge collisionality in the DIII-D tokamak. The density shelf is correlated with a doubly peaked density profile near the divertor target plate, which tends to occur for operation with the ion BX∇B drift direction away from the X-point, as currently employed for DIII-D advanced tokamak scenarios. This double-peaked divertor plasma profile is connected via the EXB drifts, arising from a strong radial electric field induced by the radial electron temperature gradient near the divertor target. The drifts lead to the reversal of the poloidal flow above the divertor target, resulting in the formation of the density shelf. The edge density shelf can be also enhanced at higher heating power, preventing large, periodic bursts of the plasma, i.e. Edge-localized Modes, in the edge region, consistent with ideal magnetohydrodynamics calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Implementation of a 9-point stencil in SOLPS-ITER and implications for Alcator C-Mod divertor plasma simulations

The SOLPS-ITER code suite is used worldwide for plasma edge modeling, the interpretation of experiments, as well as for the design of the ITER divertor. The numerical scheme of the plasma solver of the code, B2.5, is based on the assumption of perfectly field-aligned grids, while in practice grids are often strongly distorted to match divertor target shapes. Neglecting these grid distortion leads to qualitatively and quantitatively incorrect results for fluid neutral simulations, and may affect results in cold (detached) divertors even when using kinetic neutral simulations. In this contribution, we present the first results of a newly implemented 9-point stencil in B2.5 to properly handle misaligned grids. The new scheme is then applied to fluid neutral simulations of a well-diagnosed and previously modeled Alcator C-Mod discharge. Results are compared with the original 5-point scheme neglecting grid distortion effects, as well as with simulations including a full kinetic neutral model. We conclude that the 9-point stencil is essential to correctly model the transport of fluid neutrals on distorted grids, and to capture the effects of divertor closure on the fluid neutral behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2004

Development of a Method for Local Electron Temperature and Density Measurements in the Divertor of the JET Tokamak

Plasma volume recombination in the divertor, a process in which charged particles recombine to neutral atoms, contributes to plasma detachment and hence cooling at the divertor target region. Detachment has been observed at JET and other tokamaks and is known to occur at low electron temperatures (T(sub e)<1 eV) and at high electron density (n(sub e)>10(exp 20)/m(exp 3)). The ability to measure such low temperatures is therefore of interest for modelling the divertor. In present work we report development of a new spectroscopic technique for investigation of local electron density (n(sub e)) and temperature (T,) in the outer divertor at JET.

Jupen, C.↗
DOE OSTI2025

Thermal Response of a Lithium Vapor Divertor to Cyclical Operation

The lithium vapor divertor concept is being developed as a method to achieve detached divertor conditions in a tokamak while minimizing impurity radiation losses from the core plasma. SOLPS-ITER modeling has previously been used to identify some of the geometric constraints and required lithium evaporation rate of a lithium vapor divertor in a medium-sized tokamak during steady-state operation. Here an updated conceptual design based on these operating requirements is introduced and the thermal response of the system is modeled during cyclical operation, consistent with operation in a short-pulse tokamak. Controllability of the temperature of the lithium capillary porous system (CPS) is achieved by adopting a design where there is no line-of-sight for radiation from the plasma to reach the heated CPS surface. Operational strategies to minimize the amount of lithium evaporated between plasma discharges while achieving steady evaporation rates during plasma discharges are discussed and modeled here. The optimal feedforward control strategy demonstrated in this work is to ramp up the temperature of the evaporator as quickly as possible immediately before a plasma discharge and then reduce the heating to match the desired steady-state net evaporation rate just before the plasma discharge begins, allowing the thermal inertia of the system to stabilize the evaporation rate during the first second of the plasma discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Novel SOLPS-ITER simulations of X-point target and snowflake divertors

Abstract The design and understanding of alternative divertor configurations may be crucial for achieving acceptable steady-state heat and particle material loads for magnetic confinement fusion reactors. Multiple X-point alternative divertor geometries such as snowflakes and X-point targets have great potential in reducing power loads, but have not yet been simulated widely in codes with kinetic neutrals. This paper discusses recent changes made to the SOLPS-ITER code to allow for the simulation of X-point target and low-field side snowflake divertor geometries. Snowflake simulations using this method are presented, in addition to the first SOLPS-ITER simulation of the X-point target. Analysis of these results show reasonable consistency with the simple modelling and theoretical predictions, supporting the validity of the methodology implemented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Comparison of reduced model predictions for divertor detachment onset and reattachment timescales in ASDEX Upgrade and JET experiments

Building on prior analysis of ASDEX Upgrade (AUG) experiments (Henderson et al 2023 Nucl. Fusion63 086024), this study compares simple analytical formula predictions for divertor detachment onset and reattachment timescales in JET experiments. Detachment onset primarily scales with divertor neutral pressure, impurity concentration, power directed to the targets, machine size, and integral perpendicular power decay length. JET experiments, focusing on seeding mixtures of Ne and Ar, align with the detachment onset predictions. Radiation efficiencies among the impurities show good agreement with the model predictions, contrasting with AUG observations which suggested higher efficiency for Ar and lower efficiency for Ne. The time taken to re-ionise the neutral volume in front of the outer target in fully detached divertor conditions was measured following both abrupt increases in injected neutral beam power and, separately, cutting of the impurity gas flow. Re-ionisation of the neutrals occurs within approximately 1 s on JET, which aligns with the simple model prediction derived from AUG data. While the AUG results are not new, their comparison with the JET results enhances understanding, reinforcing confidence in using simple models to predict future reactor scenarios.

JET↗