Search NASA⌕ Search

SEARCH · Search NASA

Results for “edl”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Reconstruction of the Mars Science Laboratory Parachute Performance and Comparison to the Descent Simulation

The Mars Science Laboratory used a single mortar-deployed disk-gap-band parachute of 21.35 m nominal diameter to assist in the landing of the Curiosity rover on the surface of Mars. The parachute system s performance on Mars has been reconstructed using data from the on-board inertial measurement unit, atmospheric models, and terrestrial measurements of the parachute system. In addition, the parachute performance results were compared against the end-to-end entry, descent, and landing (EDL) simulation created to design, develop, and operate the EDL system. Mortar performance was nominal. The time from mortar fire to suspension lines stretch (deployment) was 1.135 s, and the time from suspension lines stretch to first peak force (inflation) was 0.635 s. These times were slightly shorter than those used in the simulation. The reconstructed aerodynamic portion of the first peak force was 153.8 kN; the median value for this parameter from an 8,000-trial Monte Carlo simulation yielded a value of 175.4 kN - 14% higher than the reconstructed value. Aeroshell dynamics during the parachute phase of EDL were evaluated by examining the aeroshell rotation rate and rotational acceleration. The peak values of these parameters were 69.4 deg/s and 625 deg/sq s, respectively, which were well within the acceptable range. The EDL simulation was successful in predicting the aeroshell dynamics within reasonable bounds. The average total parachute force coefficient for Mach numbers below 0.6 was 0.624, which is close to the pre-flight model nominal drag coefficient of 0.615.

Cruz, Juan R.↗
NASA NTRS2013

Atmosphere Assessment for MARS Science Laboratory Entry, Descent and Landing Operations

On August 6, 2012, the Mars Science Laboratory rover, Curiosity, successfully landed on the surface of Mars. The Entry, Descent and Landing (EDL) sequence was designed using atmospheric conditions estimated from mesoscale numerical models. The models, developed by two independent organizations (Oregon State University and the Southwest Research Institute), were validated against observations at Mars from three prior years. In the weeks and days before entry, the MSL "Council of Atmospheres" (CoA), a group of atmospheric scientists and modelers, instrument experts and EDL simulation engineers, evaluated the latest Mars data from orbiting assets including the Mars Reconnaissance Orbiter's Mars Color Imager (MARCI) and Mars Climate Sounder (MCS), as well as Mars Odyssey's Thermal Emission Imaging System (THEMIS). The observations were compared to the mesoscale models developed for EDL performance simulation to determine if a spacecraft parameter update was necessary prior to entry. This paper summarizes the daily atmosphere observations and comparison to the performance simulation atmosphere models. Options to modify the atmosphere model in the simulation to compensate for atmosphere effects are also presented. Finally, a summary of the CoA decisions and recommendations to the MSL project in the days leading up to EDL is provided.

Cianciolo, Alicia D.↗
NASA NTRS2012

Ground Contact Model for Mars Science Laboratory Mission Simulations

The Program to Optimize Simulated Trajectories II (POST 2) has been successful in simulating the flight of launch vehicles and entry bodies on earth and other planets. POST 2 has been the primary simulation tool for the Entry Descent, and Landing (EDL) phase of numerous Mars lander missions such as Mars Pathfinder in 1997, the twin Mars Exploration Rovers (MER-A and MER-B) in 2004, Mars Phoenix lander in 2007, and it is now the main trajectory simulation tool for Mars Science Laboratory (MSL) in 2012. In all previous missions, the POST 2 simulation ended before ground impact, and a tool other than POST 2 simulated landing dynamics. It would be ideal for one tool to simulate the entire EDL sequence, thus avoiding errors that could be introduced by handing off position, velocity, or other fight parameters from one simulation to the other. The desire to have one continuous end-to-end simulation was the motivation for developing the ground interaction model in POST 2. Rover landing, including the detection of the postlanding state, is a very critical part of the MSL mission, as the EDL landing sequence continues for a few seconds after landing. The method explained in this paper illustrates how a simple ground force interaction model has been added to POST 2, which allows simulation of the entire EDL from atmospheric entry through touchdown.

Raiszadeh, Behzad↗
NASA NTRS2014

Entry, Descent, and Landing with Propulsive Deceleration: Supersonic Retropropulsion Wind Tunnel Testing and Shock Phenomena

The future exploration of the Solar System will require innovations in transportation and the use of entry, descent, and landing (EDL) systems at many planetary landing sites. The cost of space missions has always been prohibitive, and using the natural planetary and planet's moon atmospheres for entry, and descent can reduce the cost, mass, and complexity of these missions. This paper will describe some of the EDL ideas for planetary entry and survey the overall technologies for EDL that may be attractive for future Solar System missions. Future EDL systems may include an inflatable decelerator for the initial atmospheric entry and an additional supersonic retropropulsion (SRP) rocket system for the final soft landing. A three engine retropropulsion configuration with a 2.5 in. diameter sphere-cone aeroshell model was tested in the NASA Glenn Research Center's 1- by 1-ft (1×1) Supersonic Wind Tunnel (SWT). The testing was conducted to identify potential blockage issues in the tunnel, and visualize the rocket flow and shock interactions during supersonic and hypersonic entry conditions. Earlier experimental testing of a 70deg Viking-like (sphere-cone) aeroshell was conducted as a baseline for testing of a SRP system. This baseline testing defined the flow field around the aeroshell and from this comparative baseline data, retropropulsion options will be assessed. Images and analyses from the SWT testing with 300- and 500-psia rocket engine chamber pressures are presented here. In addition, special topics of electromagnetic interference with retropropulsion induced shock waves and retropropulsion for Earth launched booster recovery are also addressed.

Palaszewski, Bryan↗
NASA NTRS2013

Mars Science Laboratory Entry Descent and Landing Simulation Using DSENDS

The most recent planetary science mission to Mars was Mars Science Laboratory (MSL) with the Curiosity rover, launched November 26, 2011 and landed at Gale Crater on August 6, 2012. This spacecraft was the first use at Mars of a complete closed-loop Guidance Navigation and Control (GN&C) system, including guided entry with a lifting body that greatly reduces dispersions during the Entry, Descent and Landing (EDL) phase to achieve a 25 km X 20 km landing error relative to the selected Gale Crater landing target. In order to confirm meeting the above landing criteria, high-fidelity simulation of the EDL phase is required. The tool used for 6DOF EDL trajectory verification analysis is Dynamics Simulator for Entry, Descent and Surface landing (DSENDS), which is a high-fidelity simulation tool from JPLs Dynamics and Real-Time Simulation Laboratory for the development, test and operations of aero-flight vehicles. DSENDS inherent capability is augmented for MSL with project-specific models of atmosphere, aerodynamics, sensors and thrusters along with GN&C flight software to enable high-fidelity trajectory simulation. This paper will present the model integration and independent verification experience of the JPL EDL trajectory analysis team.

Burkhart, P. Daniel↗
NASA NTRS2010

Reactive Sequencing for Autonomous Navigation Evolving from Phoenix Entry, Descent, and Landing

Virtual Machine Language (VML) is an award-winning advanced procedural sequencing language in use on NASA deep-space missions since 1997, and was used for the successful entry, descent, and landing (EDL) of the Phoenix spacecraft onto the surface of Mars. Phoenix EDL utilized a state-oriented operations architecture which executed within the constraints of the existing VML 2.0 flight capability, compatible with the linear "land or die" nature of the mission. The intricacies of Phoenix EDL included the planned discarding of portions of the vehicle, the complex communications management for relay through on-orbit assets, the presence of temporally indeterminate physical events, and the need to rapidly catch up four days of sequencing should a reboot of the spacecraft flight computer occur shortly before atmospheric entry. These formidable operational challenges led to new techniques for packaging and coordinating reusable sequences called blocks using one-way synchronization via VML sequencing global variable events. The coordinated blocks acted as an ensemble to land the spacecraft, while individually managing various elements in as simple a fashion as possible. This paper outlines prototype VML 2.1 flight capabilities that have evolved from the one-way synchronization techniques in order to implement even more ambitious autonomous mission capabilities. Target missions for these new capabilities include autonomous touch-and-go sampling of cometary and asteroidal bodies, lunar landing of robotic missions, and ultimately landing of crewed lunar vehicles. Close proximity guidance, navigation, and control operations, on-orbit rendezvous, and descent and landing events featured in these missions require elaborate abort capability, manifesting highly non-linear scenarios that are so complex as to overtax traditional sequencing, or even the sort of one-way coordinated sequencing used during EDL. Foreseeing advanced command and control needs for small body and lunar landing guidance, navigation and control scenarios, work began three years ago on substantial upgrades to VML that are now being exercised in scenarios for lunar landing and comet/asteroid rendezvous. The advanced state-based approach includes coordinated state transition machines with distributed decision-making logic. These state machines are not merely sequences - they are reactive logic constructs capable of autonomous decision making within a well-defined domain. Combined with the JPL's AutoNav software used on Deep Space 1 and Deep Impact, the system allows spacecraft to autonomously navigate to an unmapped surface, soft-contact, and either land or ascend. The state machine architecture enabled by VML 2.1 has successfully performed sampling missions and lunar descent missions in a simulated environment, and is progressing toward flight capability. The authors are also investigating using the VML 2.1 flight director architecture to perform autonomous activities like rendezvous with a passive hypothetical Mars sample return capsule. The approach being pursued is similar to the touch-and-go sampling state machines, with the added complications associated with the search for, physical capture of, and securing of a separate spacecraft. Complications include optically finding and tracking the Orbiting Sample Capsule (OSC), keeping the OSC illuminated, making orbital adjustments, and physically capturing the OSC. Other applications could include autonomous science collection and fault compensation.

asteroid↗
NASA NTRS2013

Entry, Descent, and Landing with Propulsive Deceleration: Supersonic Retropropulsion Wind Tunnel Testing and Shock Phenomena

The future exploration of the Solar System will require innovations in transportation and the use of entry, descent, and landing (EDL) systems at many planetary landing sites. The cost of space missions has always been prohibitive, and using the natural planetary and planet's moon atmospheres for entry, and descent can reduce the cost, mass, and complexity of these missions. This paper will describe some of the EDL ideas for planetary entry and survey the overall technologies for EDL that may be attractive for future Solar System missions. Future EDL systems may include an inflatable decelerator for the initial atmospheric entry and an additional supersonic retro-propulsion (SRP) rocket system for the final soft landing. A three engine retro-propulsion configuration with a 2.5 inch diameter sphere-cone aeroshell model was tested in the NASA Glenn 1x1 Supersonic Wind Tunnel (SWT). The testing was conducted to identify potential blockage issues in the tunnel, and visualize the rocket flow and shock interactions during supersonic and hypersonic entry conditions. Earlier experimental testing of a 70 degree Viking-like (sphere-cone) aeroshell was conducted as a baseline for testing of a supersonic retro-propulsion system. This baseline testing defined the flow field around the aeroshell and from this comparative baseline data, retro-propulsion options will be assessed. Images and analyses from the SWT testing with 300- and 500-psia rocket engine chamber pressures are presented here. In addition, special topics of electromagnetic interference with retro-propulsion induced shock waves and retro-propulsion for Earth launched booster recovery are also addressed.

Palaszewski, Bryan↗
NASA NTRSDate not supplied

Fast and Precise Trajectory Simulation for Entry, Descent, and Landing Using A Multi-Model Monte Carlo Approach

Predicting landing radius and other quantities of interest (QoI) for entry, descent, and landing (EDL) applications requires a viable uncertainty propagation method for quantifying the impact of uncertainties in wind pattern variations, atmospheric uncertainties, etc. While standard MC simulation is the defacto standard for providing robust and unbiased predictions,it is often infeasible for expensive, high-fidelity EDL models. Low-fidelity models are commonly constructed to replace the high-fidelity model in MC simulation for computational speedup,but at the expense of accuracy and unbiasedness. Emerging multi-model MC methods are bridging this gap by combining predictions from two or more models of varying fidelity and computational cost for efficient and unbiased uncertainty propagation. This work explores the use of multi-model MC for increasing the speed and precision of trajectory simulation for EDL. It is shown that combining a high-fidelity EDL model with low-fidelity models (e.g,data-driven, reduced physics) yields substantial computational speedup versus standard MCwith only the high-fidelity model. Moreover, the unbiasedness of multi-model MC predictions is highlighted by showing increased accuracy versus an approach that leverages a low-fidelity surrogate model alone.

James E. Warner↗
NASA NTRSDate not supplied

Multi-Model Monte Carlo Estimators for Trajectory Simulation

Predicting landing radius and other quantities of interest (QoI) for entry, descent, andlanding (EDL) applications requires a viable uncertainty propagation method for quantifying the impact of uncertainties in aerodynamics, atmosphere, mass properties, etc. While standard Monte Carlo (MC) simulation is the de facto standard for producing robust and unbiasedstatistical estimators, it is often infeasible for expensive, high-fidelity models. Low-fidelity models are commonly constructed to replace the high-fidelity model in MC simulation for computational speedup, but at the expense of accuracy and unbiasedness. Emerging multi-model MC methods are bridging this gap by combining predictions from two or more modelsof varying fidelity and computational cost for efficient and unbiased uncertainty propagation.This works establishes a proof of concept for using multi-model MC to increase the speed and precision of trajectory simulation for EDL. It is shown that combining a high-fidelity EDL model with low-fidelity models (e.g., data-driven, reduced physics) in this manner has the potential to yield significant efficiency and accuracy gains for certain EDL QoIs versusa standard MC approach. Moreover, the unbiasedness of multi-model MC predictions ishighlighted by showing increased accuracy versus an approach that leverages a low-fidelity model alone.

James E Warner↗
NASA NTRS2016

MarCO: Interplanetary Mission Development on a CubeSat Scale

Shortly after JPL’s Interior Exploration using Seismic Investigations, Geodesy and Heat Transport (InSight) mission launches, separates, and commences its cruise phase, two CubeSats will deploy from the launch vehicle’s upper stage and begin independent flight to Mars (Fig. 1). During InSight’s entry, descent, and landing (EDL) sequence, these twin Mars Cube One (MarCO) spacecraft will fly 3,500 km above the Martian surface, recording and relaying InSight UHF radio data to the Deep Space Network (DSN) on Earth1. MarCO is a twin CubeSat mission developed by the NASA Jet Propulsion Laboratory (JPL) to accompany the InSight (Interior Exploration using Seismic Investigations, Geodesy and Heat Transport) Mars mission lander. MarCO's primary mission objective is to launch with InSight and independently fly to Mars to serve as a communications relay during InSight's entry, descent, and landing (EDL) phase. MarCO represents a new type of deep space mission: CubeSats at Mars. Building on the development of JPL's first interplanetary CubeSat project, the Interplanetary Nano-Spacecraft Pathfinder in Relevant Environment (INSPIRE), MarCO further refined the approach to hardware, software, and ground architecture development to solve the challenges of quickly building low-budget spacecraft to fly to Mars. The greatest constraint, beyond others typical of CubeSat missions, was time. The duration between MarCO's conception to completion of spacecraft assembly was less than two years - an unprecedented schedule for any planetary mission to date. Through necessity, MarCO has built on previous experience, procedures, systems, and development methodologies, defining a new niche for supporting larger primary missions. The MarCO spacecraft are poised to write a new chapter in deep space exploration. Originally slated to launch and reach Mars in 2016, the InSight mission schedule subsequently slipped to 2018. During the original landing of InSight, Earth would not be in view, and no orbiter around Mars would have been in position to both receive UHF EDL data and simultaneously relay it back to Earth. It was from this obstacle that MarCO was conceived. Regardless of any changes to InSight’s 2018 EDL configuration geometry, MarCO is still expected to fly and serve in the same capacity as originally designed: the first CubeSat mission to Mars. CubeSats have historically been firmly in the domain of universities and small companies. As first conceived, they served as a platform upon which to teach all aspects of the space mission lifecycle. JPL took on this mission type with Interplanetary Nano-Spacecraft Pathfinder in Relevant Environment2 (INSPIRE), moving the concept into a new domain: deep space. Building from the INSPIRE platform and lessons learned, MarCO addressed new challenges in the domain of planetary missions: independent interplanetary flight and navigation, integration with a large-scale mission, long-distance and long-delay communication, short development time, and a small development team. Of these, the greatest constraint was schedule: only 18 months passed from conception of mission concept until delivery of fully assembled and tested flight hardware. Careful selection of mission team, along with extensive use of off-the-shelf equipment, and streamlining automated processes, was essential. This achievement represents the next step in the evolution of CubeSats beyond low-Earth orbit.

Werne, Thomas↗
NASA NTRSDate not supplied

Impact of NASA’s Entry Systems Modeling Project on Planetary Mission Design

Planetary missions continue to grow larger and more complex. Furthermore, the current focus on human exploration of the Moon and Mars, as well as Mars Sample Return(MSR), place increas-ingly stringent requirements on the reliability of the entry, descent, and landing (EDL) system that ensures the safe delivery of payload or crew to their destination. Planetary EDL is an area in which mission designers are critically reliant on modeling and simulation to demonstrate the reliability of the system, as there are no ground facilities that are able to fully test these systems in a flight-relevant environment. NASA’s state-of-the-art modeling and simulation capability must continually evolve to meet the needs of the next generation of planetary EDL. To accomplish this aim, NASA’s Entry Systems Modeling (ESM) Project was formed in 2013and is funded bythe Space Technology Mission Directorate(STMD) and Science Mission Directorate (SMD). ESM is the Agency’s only cross-cutting effort for advancing entry systems modeling and simulation capabilities across a range of technical disciplines and Solar System destinations. ESM is a portfolio project covering a variety of mid-TRL research efforts within four core EDL-related areas of investment: (1) Thermal protection material modeling, (2) Shock layer kinetics and radiation, (3) Aerosciences, and (4) Guidance, navigation, and con-trol. The material modeling group creates detailed material response modelsof thermal protection systems (TPS)from the micro to macro scale, and at the fun-damental and engineering levels. Shock layer kinetics and radiation focuses on radiative heating of space-craft, quantum chemistry and benchmark experiments for validation.Aerosciences is a broad research area that impacts many aspects of entry systems, including parachutes, aerodynamics, and turbulent heating augmentation due to TPS roughness.The guidance, navigation,and control effort under ESM is expanding the capabilities of NASA’s main flight mechanics tool, POST2, for use on high-performance computing architectures and to generalize interoperability with external applications for more detailed end-to-end simula-tion.In addition, several focusedresearch topics have been approvedto augment ESM’s core portfolio. These include efforts for deep post-flight analysis of Mars 2020/MEDLI2 flight data; development ofTPS failure models; improvement of hypersonic wakeflow models; and a recently concluded effort to provide material response models for NuSil-coated PICA heat-shield material. This presentation will discuss each of these investment areas and demonstrate via real mission examples how advances to the state-of-the-art enabled by ESM are directly impacting the missions of today and tomorrow, including InSight, Mars 2020, Mars Sample Return, Orion, and Dragonfly.

Entry Systems Modeling↗
NASA NTRS2022

Mars 2020 Lander Vision System Flight Performance 1

The Mars 2020 Entry Descent and Landing (EDL) system delivered the Perseverance rover to the surface of Mars on February 18th, 2021. A large fraction of the Jezero Crater landing site was covered with landing hazards including cliffs, inescapable dune fields and rocks. These hazards were identified or inferred using orbital imagery before launch so that they could be avoided using Terrain Relative Navigation (TRN) which was composed of two parts: the Lander Vision System (LVS) and Safe Target Selection (STS). During EDL, the LVS successfully estimated map relative position by fusing landmarks matched between descent imagery and a map of the landing site with Inertial Measurement Unit (IMU) data. This position estimate was used by STS to identify the safest target for landing that was also reachable given fuel and other constraints. The EDL system then used the powered descent phase to retarget to this location and land safely. The overall error between the targeted location and actual landing location was 5m which was an order of magnitude less than the 60m touchdown error requirement. This paper will describe the final tests of the LVS before launch, the checkout of the LVS during operations and the LVS performance during EDL.

Zheng, Jason↗
NASA NTRS2022

Preparing the Mars Relay Network for the Arrival of the Perseverance Rover at Mars

The Perseverance rover represents NASA’s latest achievement in Mars exploration. Landing successfully on 18 Feb 2021, the rover’s transmitted data during its entry, descent, and landing (EDL) were captured by the Mars Reconnaissance Orbiter (MRO) and the Mars Atmosphere and Volatile Evolution (MAVEN) orbiter. This data, broadcast in near-realtime to the world, allowed everyone to share in the excitement (and “terror”) of the day. The images returned thereafter included the first images of the new landing site, video of the landing itself taken from a variety of vantage points, and eventually the historic images of the first powered flight on another planet. Behind the scenes, the return of that data to Earth was accomplished via Mars orbiters operated by NASA and ESA, using three different ground tracking networks. Considered together, this Mars Relay Network (MRN) enabled the successful, timely, and unobtrusive return of the rover’s data. This paper describes the preparations taken by the participants of the MRN in anticipation of the arrival of Perseverance at Mars. These were not only focused on successfully acquiring the rover’s critical event telemetry during its EDL, but also on readying the network to return the rover’s data on an ongoing basis as it pursued its mission objectives. Included is a brief description of the MRN, which represents a highly successful international collaboration and continues as critical infrastructure for NASA’s and ESA’s ongoing Mars exploration. Also summarized are the activities performed prior to EDL, including landing site reconnaissance and mission test and training activities; those activities performed on EDL day, especially the recording, return, and processing of the rover’s critical event telemetry; and those activities that are now being performed on an ongoing basis during the rover’s surface operations, including an outline of the planning processes that enable relay services. Finally, a description of the performance of the network to-date on behalf of the Perseverance rover is given, summarizing the success of the network to provide support to both it and other spacecraft on the surface of Mars.

Srnka, Evan↗
DOE OSTI2021

Ion correlations drive charge overscreening and heterogeneous nucleation at solid–aqueous electrolyte interfaces

Significance Ion distributions at charged solid–water interfaces, referred to as the electrical double layer (EDL), are poorly understood at high ion concentrations, in part due to the lack of molecular-scale descriptions of the interactions between adsorbed hydrated ions. Here, direct visualization of the salinity-dependent evolution of EDL structure reveals molecular origins of nonclassical transformation of the EDL, in which charge overscreening and heterogeneous nucleation are driven by ion–ion correlations at the interfaces. This manifestation of the atomistic basis of nonclassical behaviors provides a much-needed understanding of the impact of ion cooperativity at charged interfaces for the development of predictive models for element transport in natural environments and advanced technologies for material growth and synthesis in saline environments.

36 MATERIALS SCIENCE↗
NASA NTRS2007

Overview of the Mars Science Laboratory Parachute Decelerator Subsystem

In 2010 the Mars Science Laboratory (MSL) mission will deliver NASA's largest and most capable rover to the surface of Mars. MSL will explore previously unattainable landing sites due to the implementation of a high precision Entry, Descent, and Landing (EDL) system. The parachute decelerator subsystem (PDS) is an integral prat of the EDL system, providing a mass and volume efficient some of aerodynamic drag to decelerate the entry vehicle from Mach 2 to subsonic speeds prior to final propulsive descent to the sutface. The PDS for MSL is a mortar deployed 19.7m Viking type Disk-Gap-Band (DGB) parachute; chosen to meet the EDL timeline requirements and to utilize the heritage parachute systems from Viking, Mars Pathfinder, Mars Exploration Rover, and Phoenix NASA Mars Lander Programs. The preliminary design of the parachute soft goods including materials selection, stress analysis, fabrication approach, and development testing will be discussed. The preliminary design of mortar deployment system including mortar system sizing and performance predictions, gas generator design, and development mortar testing will also be presented.

Entry, Descent, and Landing (EDL)↗
NASA NTRS2012

Entry, Descent, and Landing Communications for the 2011 Mars Science Laboratory

The Mars Science Laboratory (MSL), established as the most advanced rover to land on the surface of Mars to date, launched on November 26th, 2011 and arrived to the Martian Gale Crater during the night of August 5th, 2012 (PDT). MSL will investigate whether the landing region was ever suitable to support carbon-based life, and examine rocks, soil, and the atmosphere with a sophisticated suite of tools. This paper addresses the flight system requirement by which the vehicle transmitted indications of the following events using both X-band tones and UHF telemetry to allow identification of probable root causes should a mission anomaly have occurred: Heat-Rejection System (HRS) venting, completion of the cruise stage separation, turn to entry attitude, atmospheric deceleration, bank angle reversal commanded, parachute deployment, heatshield separation, radar ground acquisition, powered descent initiation, rover separation from the descent stage, and rover release. During Entry, Descent, and Landing (EDL), the flight system transmitted a UHF telemetry stream adequate to determine the state of the spacecraft (including the presence of faults) at 8 kbps initiating from cruise stage separation through at least one minute after positive indication of rover release on the surface of Mars. The flight system also transmitted X-band semaphore tones from Entry to Landing plus one minute although since MSL was occulted, as predicted, by Mars as seen from the Earth, Direct-To-Earth (DTE) communications were interrupted at approximately is approx. 5 min after Entry ( approximately 130 prior to Landing). The primary data return paths were through the Deep Space Network (DSN) for DTE and the existing Mars network of orbiting assets for UHF, which included the Mars Reconnaissance Orbiter (MRO), Mars Odyssey (ODY), and Mars Express (MEX) elements. These orbiters recorded the telemetry data stream and returned it back to Earth via the DSN. The paper also discusses the total power received during EDL and the robustness of the telecom design strategy used to ensure EDL communications coverage.

relay operations↗
NASA NTRS2013

The Mars Science Laboratory Entry, Descent, and Landing Flight Software

This paper describes the design, development, and testing of the EDL program from the perspective of the software engineer. We briefly cover the overall MSL flight software organization, and then the organization of EDL itself. We discuss the timeline, the structure of the GNC code (but not the algorithms as they are covered elsewhere in this conference) and the command and telemetry interfaces. Finally, we cover testing and the influence that testability had on the EDL flight software design.

Entry, Descent, Landing (EDL)↗
NASA NTRS2015

Mars Reconnaissance Orbiter Navigation Strategy for Dual Support of Insight and ExoMars Entry, Descent and Landing Demonstrator Module in 2016

Mars Reconnaissance Orbiter (MRO) will support NASA's InSight Mission and ESA's ExoMars Entry, Descent and Landing Demonstrator Module (EDM) in the fall of 2016 when both landers arrive at Mars. MRO provided relay support during the Entry, Descent and Landing (EDL) sequences of Mars Phoenix Lander in 2008 and the Mars Science Laboratory in 2012. Unlike these missions, MRO will coordinate between two EDL events separated by only three weeks: InSight on September 28, 2016 and EDM on October 19, 2016. This paper describes MRO Navigation's maneuver strategy to move MRO's ascending node to meet the In- Sight EDL phasing requirement and support EDM.

EDM↗