Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastic modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

A LOAD-BASED DEPTH-SENSING INDENTATION TECHNIQUE FOR ELASTIC–PLASTIC MATERIAL MECHANICAL PROPERTY EVALUATION

A load-based depth-sensing micro-indentation technique has been developed for material mechanical properties evaluation including elastic modulus, yield stress, strain hardening exponent and stress-strain curve. Based on a Hertzian contact mechanics approach, this load-based depthsensing micro-indentation technique does not require system compliance calibration or the use of high precision depth sensors. Furthermore a unique, material independent, indentation based load-depth algorithm has been developed accounting for both elastic and elastic-plastic deformation of the material beneath the indenter. This algorithm, found to be a function of material yield stress, strain hardening exponent and elastic modulus, is shown to be the basis for obtaining a stressstrain curve. Finite element analyses of multiple materials with various mechanical properties were employed to examine and develop the fundamental indention based relationships between these variables and the load/depth curve needed to extract the stress-strain diagram. In addition, experimental results obtained with this load-based micro-indentation technique were found to yield accurate material mechanical properties (elastic modulus, strain hardening, yield strength) at room and elevated temperatures (up to 1200°C).

36 MATERIALS SCIENCE↗

Rubber elasticity for percolation network consisting of Gaussian chains

A theory describing the elastic modulus for percolation networks of Gaussian chains on general lattices such as square and cubic lattices is proposed and its validity is examined with simulation and mechanical experiments on well-defined polymer networks. The theory was developed by generalizing the effective medium approximation (EMA) for Hookian spring network to Gaussian chain networks. From EMA theory, we found that the ratio of the elastic modulus at p, G to that at p = 1, G{sub 0}, must be equal to G/G{sub 0} = (p − 2/f)/(1 − 2/f) if the position of sites can be determined so as to meet the force balance, where p is the degree of cross-linking reaction. However, the EMA prediction cannot be applicable near its percolation threshold because EMA is a mean field theory. Thus, we combine real-space renormalization and EMA and propose a theory called real-space renormalized EMA, i.e., REMA. The elastic modulus predicted by REMA is in excellent agreement with the results of simulations and experiments of near-ideal diamond lattice gels.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Scuffing initiation in metals sliding against copper under non-lubricated conditions

Metallic components in sliding contact are sometimes subjected to high-loads with little or no lubrication. Such starved conditions can lead to a phenomenon called scuffing. Various definitions exist for this term, but in the present case, three criteria were used to signal its onset: changes in friction, vibrations, and noise, coupled with surface examination. On this basis, scuffing initiation was determined for seven technically pure metals (Al, Mo, Nb, Ta, Ti, W, Cu) and stainless steel, all rubbing against Cu. A flat-ended pin-on-disk test configuration was used with normal loads of 1-3 N, and with step-wise increases in sliding speed from 0.16 to 2.56 m/s. Al was only weakly resistant to scuffing, presumably due to its solubility in Cu, its high ductility and its relatively low elastic modulus. Niobium provided satisfactory sliding behavior at low speeds and loads, presumably due to protective oxides; however, it scuffed at higher loads when the oxide broke through. Stainless steel, Mo, and Ta had higher friction coefficients than Al and Nb, presumably because the relatively high strengths of the former prevented severe wear even when their oxide films failed. Like Al, Ti scuffs on Cu, probably because of its high relative solubility; however, Ti's higher elastic modulus resists the more severe forms of surface damage than does Al. Of all the materials slid against Cu, W displayed the least scuffing, even under maximum speed and load. Tungsten's negligible solubility in Cu may have reduced its adhesion, and W's high elastic modulus resisted shear-deformation, even at high frictional heating. Self-mated Cu couple scuffed when the speed was increased. The oxides on the Cu surface serve as solid lubricant avoiding scuffing at lower speeds.

36 MATERIALS SCIENCE↗

The viscoelastic characterization of polymer materials exposed to the low-Earth orbit environment

Recent accomplishments in our research efforts have included the successful measurement of the thermal mechanical properties of polymer materials exposed to the low-earth orbit environment. In particular, viscoelastic properties were recorded using the Rheometrics Solids Analyzer (RSA 2). Dynamic moduli (E', the storage component of the elastic modulus, and E'', the loss component of the elastic modulus) were recorded over three decades of frequency (0.1 to 100 rad/sec) for temperatures ranging from -150 to 150 C. Although this temperature range extends beyond the typical use range of the materials, measurements in this region are necessary in the development of complete viscoelastic constitutive models. The experimental results were used to provide the stress relaxation and creep compliance performance characteristics through viscoelastic correspondence principles. Our results quantify the differences between exposed and control polymer specimens. The characterization is specifically designed to elucidate a constitutive model that accurately predicts the change in behavior of these materials due to exposure. The constitutive model for viscoelastic behavior reflects the level of strain, the rate of strain, and the history of strain as well as the thermal history of the material.

Strganac, Thomas↗

Anomalous magneto-structural behavior of MnBi explained: A path towards an improved permanent magnet

Low-temperature MnBi (hexagonal NiAs phase) exhibits anomalies in the lattice constants (a, c) and bulk elastic modulus (B) below 100 K, spin reorientation and magnetic susceptibility maximum near 90 K, and, importantly for high-temperature magnetic applications, an increasing coercivity (unique to MnBi) above 180 K. We calculate the total energy and magneto-anisotropy energy (MAE) versus (a, c) using DFT+U methods. We reproduce and explain all the above anomalies. We predict that coercivity and MAE increase due to increasing a, suggesting means to improve MnBi permanent magnets.

36 MATERIALS SCIENCE↗

Effects of plasma and vacuum-ultraviolet exposure on the mechanical properties of low-k porous organosilicate glass

The effects of plasma exposure and vacuum-ultraviolet (VUV) irradiation on the mechanical properties of low-k porous organosilicate glass (SiCOH) dielectric films were investigated. Nanoindentation measurements were made on SiCOH films before and after exposure to an electron-cyclotron-resonance plasma or a monochromatic synchrotron VUV beam, to determine the changes of film hardness, elastic modulus, and crack threshold due to these exposures. This permits the effects of ion bombardment and photon bombardment to be analyzed separately. The role of energetic ions was examined with a variety of inert plasma-exposure conditions. The role of VUV photons was analyzed as a function of synchrotron photon energy. It was found that both energetic ions and VUV photons with energies larger than the bond energy of the Si-O bond cause a significant increase in film hardness along with a smaller increase in elastic modulus and crack threshold. Differential Fourier transform infrared spectra and x-ray photoemission spectroscopy results show that the energetic ions affect the SiCOH properties mainly through physical bombardment, during which the ions transfer their momentum to the Si-O-Si backbone and transform them into more energetically stable Si-O-Si network structures. This results in the Si-O-Si network structures becoming densified. VUV photons assist reaction that increase the number of bridging O{sub 3}≡Si-O-Si≡O{sub 3} bonds and deplete nonbridging O{sub 3}≡Si-O and C-Si≡O{sub 3} bonds. This increased degree of cross linking in porous organosilicate dielectrics can substantially enhance their hardness and elastic modulus while showing no significant film shrinkage or densification.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Influence of heating rate and aging temperature on omega and alpha phase precipitation in Ti35Nb alloy

Highlights: • The heating rate, isothermal temperature and aging time strongly affect the phase precipitation. • Aged Ti35Nb alloy presented an ultimate tensile strength of 972 MPa with elongation of 7.5%. • The elastic modulus of 78 GPa makes this aged alloy a promising candidate for biomedical application. - Abstract: Metastable β Ti alloys based on Nb exhibit features that make them suitable for load-bearing biomedical applications, so it is crucial to evaluate their phase transformation and properties. This paper discusses the effects of aging heat treatments on the microstructure, phase transformation and mechanical behavior of Ti35Nb alloy. Samples were solution heat treated in the β field, quenched and aged under different conditions of heating rates, isothermal aging temperature and isothermal aging time. To enhance the alloy's mechanical behavior, thermal analysis and high temperature X-ray diffraction experiments coupled with Vickers hardness tests were employed to determine the temperature range of isothermal ω phase precipitation, as well as α phase precipitation temperature, thereby providing information to optimize aging heat treatment conditions. Results indicate that Ti35Nb alloy subjected to a heating rate of 30 °C/min and an isothermal aging temperature of 500 °C applied for 4 h would ensure high mechanical strength and low elastic modulus. The application of these aging conditions led to a microstructure consisting of very refined α phase precipitates homogeneously dispersed in the β phase matrix, presenting an ultimate tensile strength of 972 MPa, elongation of 7.5% and elastic modulus of 78 GPa, making this aged alloy a promising candidate for biomedical applications. These results shed light on the correlations between phase transformations, microstructure and mechanical behavior in high solute content TiNb alloys for biomedical applications.

36 MATERIALS SCIENCE↗

Microstructure and nanoindentation analysis of Mg-SiC nanocomposite powders synthesized by mechanical milling

Highlights: • Mechanical milling as an effective solution to reach a homogeneous distribution of SiC nanoparticles up to 10 vol% in Mg matrix • No deformation twinning in the nanostructured Mg matrix even after the severe plastic deformation and hard SiC nanoparticles up to 10 vol%. • Significant enhancement of nanohardness and reduced elastic modulus in the milled nanocomposite powders - Abstract: Mixtures of magnesium powder and SiC nanoparticles at various volume fractions were mechanically milled to produce nanocrystalline Mg-SiC nanocomposites. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were utilized to characterize the microstructure of the milled powders. The microstructural evidences revealed that mechanical milling is a proper method to achieve a uniform distribution of the SiC nanoparticles, even up to 10% in the Mg matrix. Based on the results, higher volume fraction of the SiC nanoparticles raise the value of measured microstrain and reduce the crystallite size of the Mg matrix. The TEM results pointed to the fact that no deformation twinning takes place in the nanostructured Mg matrix even after severe plastic deformation through mechanical milling and the presence of hard SiC nanoparticles up to 10 vol%. The effects of nanoparticle volume fraction on mechanical properties of the milled Mg-SiC nanocomposites were evaluated using nanoindentation tests. The results clearly showed a significant enhancement of nanohardness and reduced elastic modulus in the milled powders compared to that of the reference material namely as-received pure magnesium. It was found that the SiC nanoparticles (even up to 10 vol%), well distributed in the magnesium matrix, remarkably improve the reduced elastic modulus and nanohardness of the nanocomposite powders.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Vibrational spectra of nanowires measured using laser doppler vibrometry and STM studies of epitaxial graphene : an LDRD fellowship report.

A few of the many applications for nanowires are high-aspect ratio conductive atomic force microscope (AFM) cantilever tips, force and mass sensors, and high-frequency resonators. Reliable estimates for the elastic modulus of nanowires and the quality factor of their oscillations are of interest to help enable these applications. Furthermore, a real-time, non-destructive technique to measure the vibrational spectra of nanowires will help enable sensor applications based on nanowires and the use of nanowires as AFM cantilevers (rather than as tips for AFM cantilevers). Laser Doppler vibrometry is used to measure the vibration spectra of individual cantilevered nanowires, specifically multiwalled carbon nanotubes (MWNTs) and silver gallium nanoneedles. Since the entire vibration spectrum is measured with high frequency resolution (100 Hz for a 10 MHz frequency scan), the resonant frequencies and quality factors of the nanowires are accurately determined. Using Euler-Bernoulli beam theory, the elastic modulus and spring constant can be calculated from the resonance frequencies of the oscillation spectrum and the dimensions of the nanowires, which are obtained from parallel SEM studies. Because the diameters of the nanowires studied are smaller than the wavelength of the vibrometer's laser, Mie scattering is used to estimate the lower diameter limit for nanowires whose vibration can be measured in this way. The techniques developed in this thesis can be used to measure the vibrational spectra of any suspended nanowire with high frequency resolution Two different nanowires were measured - MWNTs and Ag{sub 2}Ga nanoneedles. Measurements of the thermal vibration spectra of MWNTs under ambient conditions showed that the elastic modulus, E, of plasma-enhanced chemical vapor deposition (PECVD) MWNTs is 37 {+-} 26 GPa, well within the range of E previously reported for CVD-grown MWNTs. Since the Ag{sub 2}Ga nanoneedles have a greater optical scattering efficiency than MWNTs, their vibration spectra was more extensively studied. The thermal vibration spectra of Ag{sub 2}Ga nanoneedles was measured under both ambient and low-vacuum conditions. The operational deflection shapes of the vibrating Ag{sub 2}Ga nanoneedles was also measured, allowing confirmation of the eigenmodes of vibration. The modulus of the crystalline nanoneedles was 84.3 {+-} 1.0 GPa. Gas damping is the dominate mechanism of energy loss for nanowires oscillating under ambient conditions. The measured quality factors, Q, of oscillation are in line with theoretical predictions of air damping in the free molecular gas damping regime. In the free molecular regime, Q{sub gas} is linearly proportional to the density and diameter of the nanowire and inversely proportional to the air pressure. Since the density of the Ag{sub 2}Ga nanoneedles is three times that of the MWNTs, the Ag{sub 2}Ga nanoneedles have greater Q at atmospheric pressures. Our initial measurements of Q for Ag{sub 2}Ga nanoneedles in low-vacuum (10 Torr) suggest that the intrinsic Q of these nanoneedles may be on the order of 1000. The epitaxial carbon that grows after heating (000{bar 1}) silicon carbide (SiC) to high temperatures (1450-1600) in vacuum was also studied. At these high temperatures, the surface Si atoms sublime and the remaining C atoms reconstruct to form graphene. X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM) were used to characterize the quality of the few-layer graphene (FLG) surface. The XPS studies were useful in confirming the graphitic composition and measuring the thickness of the FLG samples. STM studies revealed a wide variety of nanometer-scale features that include sharp carbon-rich ridges, moire superlattices, one-dimensional line defects, and grain boundaries. By imaging these features with atomic scale resolution, considerable insight into the growth mechanisms of FLG on the carbon-face of SiC is obtained.

36 MATERIALS SCIENCE↗

Improving impact resistance of ceramic materials by energy absorbing surface layers

Energy absorbing surface layers were used to improve the impact resistance of silicon nitride and silicon carbide ceramics. Low elastic modulus materials were used. In some cases, the low elastic modulus was achieved using materials that form localized microcracks as a result of thermal expansion anisotropy, thermal expansion differences between phases, or phase transformations. In other cases, semi-vitreous or vitreous materials were used. Substantial improvements in impact resistance were observed at room and elevated temperatures.

Kirchner, H. P.↗

Fully flooded elastohydrodynamic lubricated elliptical contacts

Emphasis is on fully flooded, elastohydrodynamic lubricated, elliptical contacts. A fully flooded conjunction is one in which the film thickness is not significantly changed when the amount of lubricant is increased. A brief description of the relevant equations used in the elastohydrodynamic lubrication of elliptical contacts is given. The most important practical aspect of the elastohydrodynamic theory is the determination of the minimum film thickness within the contact. The maintenance of a fluid film of adequate magnitude is an essential feature of the correct operation of lubricated machine elements. The results presented show the influence of contact geometry on minimum film thickness as expressed by the ellipticity parameter and the dimensionless speed, load, and materials parameters. Film thickness equations are developed for materials of high elastic modulus, such as metal, and for materials of low elastic modulus, such as rubber. In addition to the film thickness equations that are developed, plots of pressure and film thickness are presented. These theoretical solutions for film thickness have all the essential features of previously reported experimental observations based on optical interferometry. Correlation between theory and experiments is also presented.

Hamrock, B. J.↗

Elastohydrodynamic lubrication of elliptical contacts

Fully flooded, elastohydrodynamically lubricated, elliptical contacts are discussed. The relevant equations used in the elastohydrodynamic lubrication (EHL) of elliptical contacts are briefly described. Film thickness equations are developed for materials of high elastic modulus, such as metal, and for materials of low elastic modulus, such as rubber. In addition to the film thickness equations that are developed, plots of pressure and film thickness are presented. A theoretical study of the influence of lubricant starvation on film thickness and pressure in hard and soft elliptical elastohydrodynamic contacts is presented. From the results for both hard and soft EHL contacts a simple and important dimensionless inlet boundary distance is specified. It is also found that the film thickness for a starved condition can be written in dimensionless terms as a function of the inlet distance parameter and the film thickness for a fully flooded condition. contour plots of pressure and film thickness in and around the contact are shown for fully flooded and starved conditions. The theoretical findings are compared directly with results obtained experimentally.

Hamrock, B. J.↗

Elastohydrodynamic lubrication of smooth surfaces

Fully flooded, elastohydrodynamically lubricated contacts are considered. Elastohydrodynamic lubrication (EHL) analysis requires the simultaneous solution of the elastically, viscosity, density, and Reynolds equations. The most important practical aspect of elastohydrodynamic lubrication theory is the determination of the minimum film thickness within the conjunction. The maintenance of a fluid film of adequate magnitude is an essential feature of the correct operation of lubricated machine elements. The results show the influence of contact geometry on minimum film thickness as expressed by the ellipticity parameter and the dimensionless speed, load, and materials parameters. Film thickness equations are developed for materials of high elastic modulus, such as metal, and for materials of low elastic modulus, such as rubber.

Hamrock, B. J.↗

An Approximate Formulation of the Effective Indentation Modulus of Elastically Anisotropic Film-on-Substrate Systems

Frictionless contact between an arbitrarily-shaped rigid indenter and an elastically anisotropic film-on-substrate system can be regarded as being superposed incrementally by a flat-ended punch contact, the shape and size of which are determined by the indenter shape, indentation depth (or applied load) and elastic properties of film and substrate. For typical nanoindentation applications, the indentation modulus can thus be approximated from the response of a circular contact with pressure of the form of [1 - (r/a){sup 2}]{sup -1/2}, where r is the radial coordinate and a is the contact radius. The surface-displacement Green's function for elastically anisotropic film-on-substrate system is derived in closed-form by using the Stroh formalism and the two-dimensional Fourier transform. The predicted dependence of the effective modulus on the ratio of film thickness to contact radius agrees well with detailed finite element simulations. Implications in evaluating film modulus by nanoindentation technique are also discussed.

36 MATERIALS SCIENCE↗

Characterization of phase properties and deformation in ferritic-austenitic duplex stainless steels by nanoindentation and finite element method

The phase properties and deformation behavior of the δ–ferrite and γ–austenite phases of CF–3 and CF–8 cast duplex stainless steels were characterized by nanoindentation and microstructure-based finite element method (FEM) models. We evaluated the elastic modulus of each phase and the results indicate that the mean elastic modulus of the δ–ferrite phase is greater than that of the γ–austenite phase, and the mean nanoindentation hardness values of each phase are approximately the same. Furthermore, the elastic FEM model results illustrate that greater von Mises stresses are located within the δ–ferrite phase, while greater von Mises strains are located in the γ–austenite phase in response to elastic deformation. The elastic moduli calculated by FEM agree closely with those measured by tensile testing. Finally, the plastically deformed specimens exhibit an increase in misorientation, deformed grains, and subgrain structure formation as measured by electron backscatter diffraction (EBSD).

36 MATERIALS SCIENCE↗

Elastic properties of granular materials under uniaxial compaction cycles

Data on andesitic and basaltic sands are presented showing compressional sound velocity, density, and creep as functions of uniaxial loading through several compaction cycles. Maximum pressures over which acoustic measurements were made were in the range from 600 to 700 bars. The dynamic elastic modulus varies with pressure in a manner analogous to that of a static elastic modulus defined by small pressure perturbations on a typical compaction cycle. After several compaction cycles, two compressional elastic moduli apparently exist at low pressure (thus two modes of compressional wave propagation through the samples are indicated). The elastic moduli observations are briefly discussed in terms of a general expression for compressibility.

Warren, N.↗

Stiff and Transparent Multilayer Thin Films Prepared Through Hydrogen-Bonding Layer-by-Layer Assembly of Graphene and Polymer [Super Stiff and Highly Transparent Multilayer Thin Films Prepared through Hydrogen-Bonding Layer-by-Layer Assembly of Graphene and Polymer]

Due to their exceptional orientation of 2D nanofillers, layer–by–layer (LbL) assembled polymer/graphene oxide thin films exhibit unmatched mechanical performance relative to any conventionally produced counterparts with similar composition. Unprecedented mechanical property improvement, by replacing graphene oxide with pristine graphene, is demonstrated in this work. Polyvinylpyrrolidone–stabilized graphene platelets are alternately deposited with poly(acrylic acid) using hydrogen bonding assisted LbL assembly. Transmission electron microscopy imaging and the Halpin–Tsai model are used to demonstrate, for the first time, that intact graphene can be processed from water to generate polymer nanocomposite thin films with simultaneous parallel–alignment, high packing density, and exfoliation. A multilayer thin film with only 3.9 vol% of highly exfoliated, and structurally intact graphene, increases the elastic modulus (E) of a polymer multilayer thin film by 322% (from 1.41 to 4.81 GPa), while maintaining visible light transmittance of ≈90%. This is one of the greatest improvements in elastic modulus ever reported for a graphene–filled polymer nanocomposite with a glassy (E > 1 GPa) matrix. In conclusion, the technique described here provides a powerful new tool to improve nanocomposite properties (mechanical, gas transport, etc.) that can be universally applied to a variety of polymer matrices and 2D nanoplatelets.

36 MATERIALS SCIENCE↗

A microstructure-guided constitutive modeling approach for random heterogeneous materials: Application to structural binders

This paper presents a microstructure-guided modeling approach to predict the effective elastic response of heterogeneous materials, and demonstrates its application toward two highly heterogeneous, uncon- ventional structural binders, i.e., iron carbonate and fly ash geopolymer. Microstructural information from synchrotron X-ray tomography (XRT) and intrinsic elastic properties of component solid phases from statistical nanoindentation are used as the primary inputs. The virtual periodic 3D microstructure reconstructed using XRT, along with periodic boundary conditions is used as a basis for strain- controlled numerical simulation scheme in the linear elastic range to predict the elastic modulus as well as the stresses in the microstructural phases. The elastic modulus of the composite material predicted from the microstructure-based constitutive modeling approach correlates very well with experimental measurements for both the materials considered. This technique efficiently links the microstructure to mechanical properties of interest and helps develop material design guidelines for novel heterogeneous composites

36 MATERIALS SCIENCE↗