Results for “energy consumption model” — Page 8

NASA NTRS2016

Liquid Oxygen/Liquid Methane Integrated Power and Propulsion

The proposed paper will cover ongoing work at the National Aeronautics and Space Administration (NASA) Johnson Space Center (JSC) on integrated power and propulsion for advanced human exploration. Specifically, it will present findings of the integrated design, testing, and operational challenges of a liquid oxygen / liquid methane (LOx/LCH4) propulsion brassboard and Solid Oxide Fuel Cell (SOFC) system. Human-Mars architectures point to an oxygen-methane economy utilizing common commodities, scavenged from the planetary atmosphere and soil via In-Situ Resource Utilization (ISRU), and common commodities across sub-systems. Due to the enormous mass gear-ratio required for human exploration beyond low-earth orbit, (for every 1 kg of payload landed on Mars, 226 kg will be required on Earth) increasing commonality between spacecraft subsystems such as power and propulsion can result in tremendous launch mass and volume savings. Historically, propulsion and fuel cell power subsystems have had little interaction outside of the generation (fuel cell) and consumption (propulsion) of electrical power. This was largely due to a mismatch in preferred commodities (hypergolics for propulsion; oxygen & hydrogen for fuel cells). Although this stove-piped approach benefits from simplicity in the design process, it means each subsystem has its own tanks, pressurization system, fluid feed system, etc. increasing overall spacecraft mass and volume. A liquid oxygen / liquid methane commodities architecture across propulsion and power subsystems would enable the use of common tankage and associated pressurization and commodity delivery hardware for both. Furthermore, a spacecraft utilizing integrated power and propulsion could use propellant residuals - propellant which could not be expelled from the tank near depletion due to hydrodynamic considerations caused by large flow demands of a rocket engine - to generate power after all propulsive maneuvers are complete thus utilizing previously wasted mass. Such is the case for human and robotic planetary landers. Although many potential benefits through integrated power & propulsion exist, integrated operations have yet to be successfully demonstrated and many challenges have already been identified the most obvious of which is the large temperature gradient. SOFC chemistry is exothermic with operating temperatures in excess of 1,000 K; however, any shared commodities will be undoubtedly stored at cryogenic temperatures (90-112 K) for mass efficiency reasons. Spacecraft packaging will drive these two subsystems in close proximity thus heat leak into the commodity tankage must be minimized and/or mitigated. Furthermore, commodities must be gasified prior to consumption by the SOFC. Excess heat generated by the SOFC could be used to perform this phase change; however, this has yet to be demonstrated. A further identified challenge is the ability of the SOFC to handle the sudden power spikes created by the propulsion system. A power accumulator (battery) will likely be necessary to handle these sudden demands while the SOFC thermally adjusts. JSC's current SOFC test system consists of a 1 kW fuel cell designed by Delphi. The fuel cell is currently undergoing characterization testing at the NASA JSC Energy Systems Test Area (ESTA) after which a Steam Methane Reformer (SMR) will be integrated and the combined system tested in closed-loop. The propulsion brassboard is approximately the size of what could be flown on a sounding rocket. It consists of one 100 lbf thrust "main" engine developed for NASA by Aerojet and two 10 lbf thrusters to simulate a reaction control system developed at NASA JSC. This system is also under development and initial testing at ESTA. After initial testing, combined testing will occur which will provide data on the fuel cell's ability to sufficiently handle the power spikes created by the propulsion system. These two systems will also be modeled using General-Use Nodal Network Solver (GUNNS) software. Once anchored with test data, this model will be used to extrapolate onto other firing profiles and used to size the power accumulator.

Banker, Brian↗

NASA NTRS1996

Pointing and Scanning Control of Instruments Using Rotating Unbalanced Masses

Motions of telescopes, satellites, and other flight bodies have been controlled by various means in the past. For example, gimbal mounted devices can use electric motors to produce pointing and scanning motions. Reaction wheels, control moment gyros, and propellant-charged reaction jets are other technologies that have also been used. Each of these methods has its advantages, but all actuator systems used in a flight environment face the challenges of minimizing weight, reducing energy consumption, and maximizing reliability. Recently, Polites invented and patented the Rotating Unbalanced Mass (RUM) device as a means for generation scanning motion on flight experiments. RUM devices have been successfully used to generate various scanning motions. The basic principle: a RUM rotating at constant annular velocity exerts a cyclic centrifugal force on the instrument or main body, thus producing a periodic scanning motion. A system of RUM devices exerts no reaction forces on the main body, requires very little energy, and is very simple to construct and control. These are significant advantages over electric motors, reaction wheels, and control moment gyroscopes. Although the RUM device very easily produces scanning motion, an auxiliary control system may be required to maintain the proper orientation, or pointing of the main body. It has been suggested that RUM devices can be used to control pointing dynamics, as well as generate the desired periodic scanning motion. The idea is that the RUM velocity will not be constant, but will vary over the period of one RUM rotation. The thought is that the changing angular velocity produces a centrifugal force having time-varying magnitude and direction. The scope of the present research project is to further study the pointing control concept, and to implement a microcontroller program to control an experimental hardware system. This report is subdivided into three themes. The basic dynamic modeling and control principles are described first. Then, the controller implementation and preliminary test results are discussed. Finally, suggestions for future work are presented.

Hung, John Y.↗

NASA NTRS2026

Beyond Melting: Amorphous Bonding for Joining and Consolidation

Crystallization may be the hidden constraint in thermoplastic composite manufacturing. It requires tightly controlled cooling, induces residual stresses through shrinkage, and introduces path-dependent behavior that complicates predictive modeling yet remains essential for structural performance. This work asks: can bonding be achieved without relying on melt-driven crystallization? To address this, thin (5–20 μm) polyetherimide (PEI) interlayers are pre-healed to slow-cooled polyaryletherketone (PAEK) in two contexts. The first, Thermabond®, is sub-melt joining of low melt-PAEK laminates. Results show that bond quality is governed primarily by processing (i.e., adequate healing and film handling) rather than modest changes in interlayer thickness. This concept is then extended to laminate-scale manufacturing through an architecture known as OATMEAL (Out-of-autoclave Amorphous/semicrystalline Thermoplastic Material for Energy-efficient Aerospace-grade Laminates). PEI is healed to carbon fiber reinforced polyetheretherketone (PEEK) at the prepreg and excess PEI is then ablated from the surface. Crystallinity is developed off-line during prepreg fabrication, while subsequent consolidation occurs below the melt temperature to preserve it. Cross-ply warpage experiments show that, contrary to intuition, repeated amorphous interfaces reduce global curvature by lowering the effective stress lock-in temperature and eliminating crystallization shrinkage from the lamina response. Correspondingly, laminate behavior is accurately predicted using classical laminate theory (CLT) with a single effective stress-free temperature, whereas conventional CF/PEEK requires accounting for crystallization-driven effects. By decoupling interfacial healing from crystallization, OATMEAL enables sub-melt consolidation, reduces energy consumption by up to 75%, and increases manufacturing throughput by fivefold. These results demonstrate that amorphous bonding is not only a joining strategy, but a pathway to more predictable and scalable thermoplastic composite manufacturing.

solidification↗

NASA NTRS2012

Visible Light Responsive Catalysts Using Quantum Dot-Modified Ti02 for Air and Water Purification

The method of photocatalysis utilizing titanium dioxide, TiO2, as the catalyst has been widely studied for trace contaminant control for both air and water applications because of its low energy consumption and use of a regenerable catalyst. Titanium dioxide requires ultraviolet light for activation due to its band gap energy of 3.2 eV. Traditionally, Hg-vapor fluorescent light sources are used in PCO reactors and are a setback for the technology for space application due to the possibility of Hg contamination. The development of a visible light responsive (VLR) TiO2-based catalyst could lead to the use of solar energy in the visible region (approx.45% of the solar spectrum lies in the visible region; > 400 nm) or highly efficient LEDs (with wavelengths > 400 nm) to make PCO approaches more efficient, economical, and safe. Though VLR catalyst development has been an active area of research for the past two decades, there are few commercially available VLR catalysts; those that are available still have poor activity in the visible region compared to that in the UV region. Thus, this study was aimed at the further development of VLR catalysts by a new method - coupling of quantum dots (QD) of a narrow band gap semiconductor (e.g., CdS, CdSe, PbS, ZnSe, etc.) to the TiO2 by two preparation methods: 1) photodeposition and 2) mechanical alloying using a high-speed ball mill. A library of catalysts was developed and screened for gas and aqueous phase applications, using ethanol and 4-chlorophenol as the target contaminants, respectively. Both target compounds are well studied in photocatalytic systems serve as model contaminants for this research. Synthesized catalysts were compared in terms of preparation method, type of quantum dots, and dosage of quantum dots.

Coutts, Janelle L.↗

NASA NTRS2014

Visible-Light-Responsive Catalysts Using Quantum Dot-Modified TiO2 for Air and Water Purification

Photocatalysis, the oxidation or reduction of contaminants by light-activated catalysts, utilizing titanium dioxide (TiO2) as the catalytic substrate has been widely studied for trace contaminant control in both air and water applications. The interest in this process is due primarily to its low energy consumption and capacity for catalyst regeneration. Titanium dioxide requires ultraviolet light for activation due to its relatively large band gap energy of 3.2 eV. Traditionally, Hg-vapor fluorescent light sources are used in PCO reactors; however, the use of mercury precludes the use of this PCO technology in a spaceflight environment due to concerns over crew Hg exposure. The development of a visible-light responsive (VLR) TiO2-based catalyst would eliminate the concerns over mercury contamination. Further, VLR development would allow for the use of ambient visible solar radiation or highly efficient LEDs, both of which would make PCO approaches more efficient, flexible, economical, and safe. Though VLR catalyst development has been an active area of research for the past two decades, there are few commercially available VLR catalysts. Those VLR catalysts that are commercially available do not have adequate catalytic activity, in the visible region, to make them competitive with those operating under UV irradiation. This study was initiated to develop more effective VLR catalysts through a novel method in which quantum dots (QD) consisting of narrow band gap semiconductors (e.g., CdS, CdSe, PbS, ZnSe, etc.) are coupled to TiO2 via two preparation methods: 1) photodeposition and 2) mechanical alloying using a high-speed ball mill. A library of catalysts was developed and screened for gas and aqueous phase applications using ethanol and 4-chlorophenol as the target contaminants, respectively. Both target compounds are well studied in photocatalytic systems and served as model contaminants for this research. Synthesized catalysts were compared in terms of preparation method, nature of the quantum dots, and dosage of quantum dots.

visible light↗

NASA NTRSDate not supplied

Recommendations For Developing Space Suit Integrated Food Systems and Delivering Nutrition Before, During, and After Lunar Eva

INTRODUCTION Artemis missions will include a higher tempo and frequency of extravehicular activities (EVAs) than any previous space program. Because of the physical demands expected from the crew, future space suit designs are required to incorporate nutritional support to the astronauts during lunar surface EVAs lasting longer than 4 hours. The purpose of this project was to provide recommendations to aid the development of an in-suit system that can adequately, safely, and acceptably deliver nutrition to a crewmember while confined to a space suit during EVA. METHODS Physiological, logistical, and engineering aspects of potential in-suit nutrition approaches were assessed through literature reviews, assessments of commercial off the shelf (COTS) foods, suit volumetric modeling, and feedback from subject matter experts and crewmembers. Key driving factors in the development of in-suit nutrition requirements included how much and what type of nutrition should be included, what food formulations are appropriate and safe, what are inherent limitations of space suits, what are the potential risks to the crewmember in the suit, and what practices and preferences from astronauts should be considered. Design references were conceptualized and assessed for strengths and limitations as potential in-suit nutrition systems for surface EVA. RESULTS Acute exogenous energy demands vary greatly depending on activity intensity and duration, and partial energy replenishment (i.e., 60–80 kcal∙hr-1 of EVA, or 460–680 kcal for EVAs lasting up to 8 hours) during activities could improve performance, safety, and recovery. COTS foods capable of providing these energy requirements exist; however, no COTS foods have been identified that pass NASA flight standards for microbiological safety and stability. In-suit nutrition delivery design references that were considered included in-suit concepts for a prefilled drink bag, a hydratable drink bag, and a solid food stick. In addition, a helmet feed port concept was considered for use with drink bags external to the suit. Volumetric models of the in-suit drink bag concepts, based on xEMU dimensions, indicate challenges of fitting formulations > 200 ml (equating to approximately 200 kcal). Astronaut feedback on the four concepts indicated that despite some individual preferences for inclusion of solid foods and helmet port designs, the prefilled drink bag concept was the most preferred. A prefilled drink bag can only be used if food safety and stability can be ensured, possibly requiring advancements in food delivery hardware. CONCLUSION The ability to meet the increased need for nutrition during surface EVAs through provision of nutrients in the suited configuration would benefit overall crew health, performance, and morale, and thus increase the likelihood of mission success. It is recommended that in-suit nutrition capabilities provide at least 400–600 kcal within the suit during EVAs lasting > 4 hours and that suit designs include a dedicated volume for food grade nutrition systems. The developed food system should either allow for 1) installation of prefilled (sealed sterile) liquid nutrition in the suit and provide a mechanism to break the seal at the time that consumption is desired or 2) demonstrate that the unsealed food product shelf life allows for safe consumption after at least 12 hours of EVA.

E L Dillon↗

NASA NTRSDate not supplied

Recommendations for Developing Space Suit Integrated Food Systems and Delivering Nutrition Before, During, and After Lunar EVA

INTRODUCTION Artemis missions will include a higher tempo and frequency of extravehicular activities (EVAs) than any previous space program. Because of the physical demands expected from the crew, future space suit designs are required to incorporate nutritional support to the astronauts during lunar surface EVAs lasting longer than 4 hours. The purpose of this project was to provide recommendations to aid the development of an in-suit system that can adequately, safely, and acceptably deliver nutrition to a crewmember while confined to a space suit during EVA. METHODS Physiological, logistical, and engineering aspects of potential in-suit nutrition approaches were assessed through literature reviews, assessments of commercial off the shelf (COTS) foods, suit volumetric modeling, and feedback from subject matter experts and crewmembers. Key driving factors in the development of in-suit nutrition requirements included how much and what type of nutrition should be included, what food formulations are appropriate and safe, what are inherent limitations of space suits, what are the potential risks to the crewmember in the suit, and what practices and preferences from astronauts should be considered. Design references were conceptualized and assessed for strengths and limitations as potential in-suit nutrition systems for surface EVA. RESULTS Acute exogenous energy demands vary greatly depending on activity intensity and duration, and partial energy replenishment (i.e., 60–80 kcal∙hr-1 of EVA, or 460–680 kcal for EVAs lasting up to 8 hours) during activities could improve performance, safety, and recovery. COTS foods capable of providing these energy requirements exist; however, no COTS foods have been identified that pass NASA flight standards for microbiological safety and stability. In-suit nutrition delivery design references that were considered included in-suit concepts for a prefilled drink bag, a hydratable drink bag, and a solid food stick. In addition, a helmet feed port concept was considered for use with drink bags external to the suit. Volumetric models of the in-suit drink bag concepts, based on xEMU dimensions, indicate challenges of fitting formulations > 200 ml (equating to approximately 200 kcal). Astronaut feedback on the four concepts indicated that despite some individual preferences for inclusion of solid foods and helmet port designs, the prefilled drink bag concept was the most preferred. A prefilled drink bag can only be used if food safety and stability can be ensured, possibly requiring advancements in food delivery hardware. CONCLUSION The ability to meet the increased need for nutrition during surface EVAs through provision of nutrients in the suited configuration would benefit overall crew health, performance, and morale, and thus increase the likelihood of mission success. It is recommended that in-suit nutrition capabilities provide at least 400–600 kcal within the suit during EVAs lasting > 4 hours and that suit designs include a dedicated volume for food grade nutrition systems. The developed food system should either allow for 1) installation of prefilled (sealed sterile) liquid nutrition in the suit and provide a mechanism to break the seal at the time that consumption is desired or 2) demonstrate that the unsealed food product shelf life allows for safe consumption after at least 12 hours of EVA.

space suit↗

NASA NTRS2014

An Integrated Approach to Modeling Solar Electric Propulsion Vehicles During Long Duration, Near-Earth Orbit Transfers

Recent NASA interest in utilizing solar electronic propulsion (SEP) technology to transfer payloads, e.g. from low-Earth orbit (LEO) to higher energy geostationary-Earth orbit (GEO) or to Earth escape, has necessitated the development of high fidelity SEP vehicle models and simulations. These models and simulations need to be capable of capturing vehicle dynamics and sub-system interactions experienced during the transfer trajectories which are typically accomplished with continuous-burn (potentially interrupted by solar eclipse), long duration "spiral out" maneuvers taking several months or more to complete. This paper presents details of an integrated simulation approach achieved by combining a high fidelity vehicle simulation code with a detailed solar array model. The combined simulation tool gives researchers the functionality to study the integrated effects of various vehicle sub-systems (e.g. vehicle guidance, navigation and control (GN&C), electric propulsion system (EP)) with time varying power production. Results from a simulation model of a vehicle with a 50 kW class SEP system using the integrated tool are presented and compared to the results from another simulation model employing a 50 kW end-of-life (EOL) fixed power level assumption. These models simulate a vehicle under three degree of freedom dynamics (i.e. translational dynamics only) and include the effects of a targeting guidance algorithm (providing a "near optimal" transfer) during a LEO to near Earth escape (C (sub 3) = −2.0 km (sup 2) / sec (sup −2) spiral trajectory. The presented results include the impact of the fully integrated, time-varying solar array model (e.g. cumulative array degradation from traversing the Van Allen belts, impact of solar eclipses on the vehicle and the related temperature responses in the solar arrays due to operating in the Earth's thermal environment, high fidelity array power module, etc.); these are used to assess the impact on vehicle performance (i.e. propellant consumption) and transit times.

vehicle↗

NASA NTRS2024

Advances in Thermoplastic Composites Over Three Decades – A Literature Review

Recently, there has been a renewed interest in thermoplastic composites driven mainly by advances in automation which can lead to significant cost reductions by increasing manufacturing rates while simultaneously reducing the part count and energy consumption relative to the manufacturing of thermoset composites. At the same time, new material systems have been developed and the thermoplastic composites prepreg material quality has improved over time. Additionally, thermoplastic composites have nearly infinite room-temperature shelf life and production scraps can be reused and retired parts can be recycled, providing opportunities for more sustainable operations and downstream markets. These factors have contributed to a strong interest in advancing thermoplastic composites for aerospace, automotive, and other industrial applications. The objective of the present study is to assess the state of the art regarding the maturity and performance of thermoplastic composite materials and to document the advances made in manufacturing and assembly of thermoplastic composite structures. Therefore, more than 200 NASA reports, conference proceedings and journal papers spanning three and a half decades (1986-2022) were reviewed and the findings summarized. The current study, however, is limited in scope with a focus on the application of thermoplastic composites to aircraft structures. Further, the study does not provide a comprehensive assessment of the available literature but rather offers an overview of past and present research being conducted in the field of thermoplastic composites. The information provided may be used to identify gaps and help guide future research and development. In this report, the opportunities offered by the use of thermoplastic composites in general and challenges encountered in particular are presented first. Second, an overview of thermoplastic materials is presented, manufacturing methods are discussed, and new methods for fastener-less assembly such as welding are introduced. Third, tests that have been performed on different levels of the building block, ranging from coupon to structural level, are presented. In particular, fracture toughness results for different thermoplastic composite materials are used to demonstrate their performance compared to state-of-the-art thermoset composites. Fourth, several examples of analyses are discussed including process modelling and progressive damage analysis (PDA). An extensive list of references and appendices with tables support the narrative. Lastly, a brief summary with outlook and recommendations for future research is provided.

composites↗

NASA NTRS2002

Body mass, energy intake, and water consumption of rats and humans during space flight

Alteration of metabolism has been suggested as a major limiting factor to long-term space flight. In humans and primates, a negative energy balance has been reported. The metabolic response of rats to space flight has been suggested to result in a negative energy balance. We hypothesized that rats flown in space would maintain energy balance as indicated by maintenance of caloric intake and body mass gain. Further, the metabolism of the rat would be similar to that of laboratory-reared animals. We studied the results from 15 space flights lasting 4 to 19 d. There was no difference in average body weight (206 +/- 13.9 versus 206 +/- 14.8 g), body weight gain (5.8 +/- 0.48 versus 5.9 +/- 0.56 g/d), caloric intake (309 +/- 21.0 versus 309 +/- 20.1 kcal/kg of body mass per day), or water intake (200 +/- 8.6 versus 199 +/- 9.3 mL/kg of body mass per day) between flight and ground control animals. Compared with standard laboratory animals of similar body mass, no differences were noted. The observations suggested that the negative balance observed in humans and non-human primates may be due to other factors in the space-flight environment.

Non-NASA Center↗

NASA NTRS1998

Hydrogen consumption by methanogens on the early Earth

It is possible that the first autotroph used chemical energy rather than light. This could have been the main source of primary production after the initial inventory of abiotic organic material had been depleted. The electron acceptor most readily available for use by this first chemoautotroph would have been CO2. The most abundant electron donor may have been H2 that would have been outgassing from volcanoes at a rate estimated to be as large as 10(12) moles yr-1, as well as from photo-oxidation of Fe+2. We report here that certain methanogens will consume H2 down to partial pressures as low as 4 Pa (4 x 10(-5) atm) with CO2 as the sole carbon source at a rate of 0.7 ng H2 min-1 microgram-1 cell protein. The lower limit of pH2 for growth of methanogens can be understood on the basis that the pH2 needs to be high enough for one ATP to be synthesized per CO2 reduced. The pH2 values needed for growth measured here are consistent with those measured by Stevens and McKinley for growth of methanogens in deep basalt aquifers. H2-consuming autotrophs are likely to have had a profound effect on the chemistry of the early atmosphere and to have been a dominant sink for H2 on the early Earth after life began rather than escape from the Earth's atmosphere to space.

Non-NASA Center↗