Results for “experimental methods development” — Page 8

DOE OSTI2021

An Investigation into High Voltage Spiral Generators Utilizing Thyristor Input Switches

High voltage nanosecond pulses are widely used in scientific research, but their wider adoption in industry requires compact, cost effective and easy to use generators to be developed. This paper presents modelling and experimental investigations into one method of producing such pulses – a spiral generator with a solid-state, thyristor-based input switch. It includes how the pulses are formed within the spiral, why a high speed input switch is required, how the geometry of the spiral dictates its output characteristics, and the effects of different loads. Using thyristors, often connected in series to increase the operating voltage of the spiral, enables the spiral generators to have low jitter, high repetition rate, and long lifetime. Modelling of the circuit used a combination of telegraph equations to account for the wave propagation along the spiral and a lumped circuit exchanging charge between the spiral, the input switch, and the load. The model is verified by detailed experimental results with the relative error being < 10% in most cases. Here, the output voltage pulse was often observed to have an initial peak of much lower magnitude than the subsequent peak(s) – which can only be fully explained by considering wave propagation effects. Lower input switch inductance, shorter switching time, larger mean diameter of the spiral, and increasing the width of the copper tape that makes up the spiral can all increase the voltage multiplication efficiency. Though increasing the number of turns that make up the spiral can increase the output voltage, it can also lower the multiplication efficiency. By understanding the effects of different geometries the spiral can be optimized to drive different loads - three applications of such spiral generators are then presented: pulses with 10 kV amplitude and 10 kHz repetition rate for driving DBD plasma, pulses with amplitude of 10 kV and 10 kV/ns rising rate for triggering of advanced solid state switches, and pulses with -50 kV amplitude and 50 ns rising time for triggering high current gas switches through field distortion.1 Index Terms—spiral generator, nanosecond pulses, telegraph equations, series-connected thyristor module, pulse forming process

42 ENGINEERING↗

DOE OSTI2026

Expanding the Domain of Applicability of Machine Learning Models with Limited Data for Drug Property Prediction

Accurate machine learning models for predicting small molecule interactions with biological targets are essential for therapeutic discovery, biothreat response, and computational drug design, but their performance is often limited for understudied targets with sparse experimental data. To address this challenge, we developed and evaluated methods to improve molecular property prediction under low-data conditions, using the NimA-related kinase (NEK) family as a proof-of-concept. This work focused on two complementary goals within the ATOM Modeling PipeLine (AMPL) and the Generative Molecular Design (GMD) loop: expanding model applicability through transfer learning, representation learning, feature scaling, sampling strategies, and active-learning-inspired compound selection; and enabling efficient virtual screening to prioritize compounds that balance predicted activity, design objectives, and synthetic accessibility.

organic↗

DOE OSTI2021

EpitopeVec: linear epitope prediction using deep protein sequence embeddings

Motivation: B-cell epitopes (BCEs) play a pivotal role in the development of peptide vaccines, immuno-diagnostic reagents and antibody production, and thus in infectious disease prevention and diagnostics in general. Experimental methods used to determine BCEs are costly and time-consuming. Therefore, it is essential to develop computational methods for the rapid identification of BCEs. Although several computational methods have been developed for this task, generalizability is still a major concern, where cross-testing of the classifiers trained and tested on different datasets has revealed accuracies of 51–53%. Results: We describe a new method called EpitopeVec, which uses a combination of residue properties, modified antigenicity scales, and protein language model-based representations (protein vectors) as features of peptides for linear BCE predictions. Extensive benchmarking of EpitopeVec and other state-of-the-art methods for linear BCE prediction on several large and small datasets, as well as cross-testing, demonstrated an improvement in the performance of EpitopeVec over other methods in terms of accuracy and area under the curve. As the predictive performance depended on the species origin of the respective antigens (viral, bacterial and eukaryotic), we also trained our method on a large viral dataset to create a dedicated linear viral BCE predictor with improved cross-testing performance.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

Initial development of a method for correlating indentation test results to damage accumulation in high temperature structural materials

This report describes an experimental approach based on microindentation creep or relaxation tests for assessing the remaining creep life of a sample material. The objective for this experimental program is to complement the development of passively loaded in situ surveillance specimens. These surveillance specimens could be placed in future advanced reactors to assess the degradation of structural properties, primary creep and creep-fatigue life, when the material is exposed to actual reactor operating conditions. The specimens and the corresponding indentation test protocol could form the basis of a structural health monitoring program designed to ensure the safe continued operation of the component given the relatively unknown effect of the reactor coolant chemistry, radiation exposure, and other environmental effects on the material properties of the constituent structural materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Interlaboratory Reproducibility of Contour Method Data in a High Strength Aluminum Alloy

The contour method for residual stress measurement has seen significant development, but an experimental reproducibility study utilizing physical samples has not been published. A double-blind reproducibly study is reported, having scope beginning with EDM cutting and ending with residual stress calculation. A reinforced I-beam sample geometry is identified for its unique residual stress profile when extracted from residual stress bearing quenched aluminum bar (7050-T74). Contour measurements are prescribed on a midplane of symmetry with dimensions 24.0 mm by 50.0 mm. Fourteen identically prepared samples are fabricated from a single long bar with well characterized and uniform residual stress. Five samples throughout the bar are identified for planning measurements to validate sample uniformity and overall suitability of the residual stress field. The planning measurements employ a range of techniques: contour method, neutron diffraction, and hole-drilling. Eight samples are distributed to an international group of participants to execute their standard measurement practice. A double-blind process is followed to provide anonymity. Results are provided by eight participants: six being self-similar and two being quite different, the latter set aside as outliers. An average residual stress field is established from non-outlying results and the spatial distribution of reproducibility standard deviation is determined. The average stress field ranges from -60 to 70 MPa and the reproducibility standard deviation averages 8.1 MPa on the measurement plane. The average reproducibility standard deviation is about 3 × larger for points within 1.0 mm of plane boundaries (17.6 MPa) than for the remaining points (6.1 MPa). Reproducibility standard deviation (among different labs) for contour method residual stress measurement is found to be very similar to repeatability standard deviation (in a single lab) reported in prior work. The reproducibility observed here, for the entire measurement process, is also similar to that found in a prior reproducibility study limited to contour method data analysis.

36 MATERIALS SCIENCE↗

DOE OSTI2026

CRADA Number NFE-22-09333 with Holocene Climate Corporation (CRADA Final Report:)

Holocene Climate Corporation has developed and scaled up a novel technology for Direct Air Capture (DAC) that is based on cutting-edge research initiated at Oak Ridge National Laboratory (ORNL). According to the IPCC, carbon dioxide capture from the air and its sequestration are necessary to keep global temperature rise below 1.5°C by 2050. DAC is a viable and practical way to reach this goal. DAC can happen anywhere in the world, takes up a fraction of the land of forests, and along with the sequestration of CO 2 , provides permanent and verifiable removal of carbon from the atmosphere. The proposed project aimed to facilitate knowledge transfer from ORNL to Holocene focusing on (i) the synthesis of the ORNL patented material which builds the cornerstone of the DAC technology, and (ii) required analytical methods needed to conduct crystallization bench-scale experimentation and technology development. Furthermore, ORNL conducted research centered around CO 2 absorption using an air-liquid contacting structure with an aqueous amino acid solution. The achievements under this project comprise successful knowledge transfer from ORNL to the entire Holocene team to jump-start their internal R&D and technological development activities.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

The influence of thermochemistry on the reactivity of propane, the pentane isomers and $n$-heptane in the low temperature regime

In this study, the influence of thermochemistry on the reactivity of fuels at low temperatures (600–1000 K) is studied here. Specifically, the effect of different sets of thermochemistry on chemical model predictions is explored, where various sets are calculated at different levels of theory in addition to recently updated group additivity values. Experimentally measured ignition delay times for propane, the pentane isomers and n-heptane are simulated using NUIGMech1.2 and replacing the thermochemistry of the low-temperature species with the calculated values. For propane, three different thermochemistry sets were calculated, namely CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//B2PLYP-D3/TZ (QM1), CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//ωB97X-D/TZ (QM2) and B2PLYP-D3/TZ/ωB97X-D/6-31G*//ωB97X-D/6-31G* (QM3). The QM2 results provide parameters to optimize new group additivity (NGA) values which are used to calculate the fourth set of thermochemistry. The model predictions using these four sets are compared to those using NUIGMech1.2 for propane. As the QM1 and QM2 calculations are expensive, the thermochemistry calculated from the QM3 and NGA calculations are used in the pentane isomer and n-heptane models. For all of the models, it is found that the thermochemistry of the species involved in the low-temperature reaction sequence ($RH$, $\dot{R}$, $RO_2H$, $R\dot{O}_2$, $\dot{Q}OOH$ and $\dot{O}_2QOOH$ species) significantly affect fuel reactivity. The NGA values were developed based on all of these species except $\dot{O}_2QOOH$ radicals. The thermochemistry of $\dot{O}_2QOOH$ species cannot be accurately calculated with the NGA representations due to the importance of non-next-nearest neighbor interactions of –OOH substitution. Further development of the NGA method to capture such interactions is in progress. Overall, the model developed using the NGA thermochemistry shows better agreement with experimental data than the model using thermochemistry from affordable and prominent QM methods, such as QM3. Based on the results presented for propane, the pentane isomers and n-heptane, the thermochemistry calculated using the NGA method can be used to model the oxidation of higher order hydrocarbons at low temperatures.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

A Cost-Effective Electro-Hydraulic Actuator Solution with Open Circuit Architecture

With the recent electrification trend in the fluid power area, more research has been incentivized to propose cost-effective and energy-efficient solutions for hydraulic systems. Hence, electro-hydraulic actuator (EHA) architectures receive increasing attention. The paper proposes a novel open-circuit EHA architecture, with the goal to obtain a cost-effective solution for mobile applications while maximizing the overall system efficiency. The proposed EHA is capable of meeting or exceeding traditional off-road machine performance, therefore enabling further electrification of off-road machines. Four-quadrant functionality, covering the full speed range, is achieved by a combination of a variable electro-hydraulic drive and valves with different functions. Focusing on the steady-state performance, the functionality is validated by numerical as well as experimental methods. A simulation model based on the Amesim environment and a dedicated test setup was developed to verify the performance. Furthermore, the good match between simulation and experimental results confirms the potential of the formulation approach of the proposed EHA for applications with different duty cycles and power levels.

4-quadrant functionality↗

DOE OSTI2023

Comparison of different noble gas injections by massive gas injection on plasma disruption mitigation on Experimental Advanced Superconducting Tokamak

Massive gas injection (MGI) is a traditional plasma disruption mitigation method. This method directly injected massive gas into the pre-disruption plasma and had been developed on the Experimental Advanced Superconducting Tokamak (EAST). Different noble gas injection experiments, including He, Ne, and Ar, were performed to compare the mitigation effect of plasma disruption by evaluating the key parameters such as flight time, pre-thermal quench (pre-TQ), and current quench (CQ). The flight time was shorter for low atomic number ( Z ) gas, and the decrease in flight time by increasing the amount of gas was insignificant. However, both pre-TQ and CQ durations decreased considerably with the increase in gas injection amount. The effect of atomic mass on pre-TQ and CQ durations showed the opposite trend. The observed trend could help in controlling CQ duration in a reasonable area. Moreover, the analysis of radiation distribution with different impurity injections indicated that low Z impurity could reduce the asymmetry of radiation, which is valuable in mitigating plasma disruption. These results provided essential data support for plasma disruption mitigation on EAST and future fusion devices.

Physics↗

DOE OSTI2025

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY25

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) project is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments [1]. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline collaboration to provide engineers with experience in both numerical simulations and experimental methods. This work uses and provides feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development.

42 ENGINEERING↗

DOE OSTI2023

Friction Stir Scribe Joining of CFRP to Aluminum (Abstract)

The objective of this project is to develop and demonstrate friction stir scribe (FSS) joining of carbon fiber reinforced polymer (CFRP) to aluminum on light-duty vehicle body-in-white (BIW) joints. The project will also overcome the major obstacles of implementing FSS technology in a fully 3-D production robotic work cell and demonstrate the required CFRP-aluminum joint strengths in industrially relevant light-duty, BIW components. Specifically the project will develop the critical process technology, models and tools necessary to advance the FSS method through experimentation, validation at the laboratory scale, and integration into a production-like robotic environment. The ultimate goal is to demonstrate the technology on industrially relevant components based on process development and numerical simulation performed at scale.

42 ENGINEERING↗

DOE OSTI2021

Experimental Studies of the Dynamics of Adsorbed and Condensed Phase Iodine Species Formed in Severe Reactor Accidents (Final Project Report)

We have studied the chemical transformations of semi-volatile organic iodide species (RI) in the condensed phase as well as adsorbed onto the surfaces of environmentally relevant particles, e.g., soot (carbon) and dust (silica) under real-world conditions. The combination of chosen experimental methods provide a molecular-level insight into the chemical dynamics of organic iodides. Throughout this project, we have developed new experimental, quantum chemistry, and data analysis capabilities. All experimental work was performed with 127 I.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2024

Experimental and Theoretical Evaluation of Feed Flow Collar Design For 3D Printed Shell-Fed Hollow Fiber Membrane Modules

This presentation was given at the 2024 AIChE Annual Meeting, San Diego, CA, October 27-31, 2024. The presentation details a method for the efficient fabrication and approximation of membrane performance, developed utilizing 3D printed experimental modules for small hollow fiber modules containing multiple fibers for experimental and simulation comparisons.

Tran, Thien↗

DOE OSTI2021

TRUST Contact Thermal Conductance (CTC) Report

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) work package is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline training to provide engineers with experience in both numerical simulations and experimental methods. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), and the test information management system (TIMS).

42 ENGINEERING↗

DOE OSTI2021

TRUST End-of-Year Report

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) work package is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline training to provide engineers with experience in both numerical simulations and experimental methods. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), and the test information management system (TIMS). TRUST includes four testbeds and their associated engineering analysis baseline models (EABMs): 1. contact thermal conductivity (CTC); 2. nonlinear dynamics (ND); 3. sensors in environments for accelerometers (SEA); 4. sensors in environments for fiber optic displacement gages (SEFOD).

42 ENGINEERING↗

DOE OSTI2021

TRUST Nonlinear Dynamics (ND) Report

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) work package is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline training to provide engineers with experience in both numerical simulations and experimental methods. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), and the test information management system (TIMS).

42 ENGINEERING↗

DOE OSTI2022

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY2022

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) work package is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline training to provide engineers with experience in both numerical simulations and experimental methods. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), test information management system (TIMS), and [WAVES] Analysis for Verified Engineering Simulation (WAVES).

42 ENGINEERING↗

DOE OSTI2023

TRUST Contact Thermal Conductance (TRUST-CTC) Report: FY23

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) work package is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are critical to the current and future stockpile. Staff development will include cross-discipline training to provide engineers with experience in both numerical simulations and experimental methods. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), test information management system (TIMS), and [WAVES] Analysis for Verified Engineering Simulation (WAVES).

42 ENGINEERING↗