Search NASA⌕ Search

SEARCH · Search NASA

Results for “fuel type”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

A Materials Compatibility and Thermal Stability Analysis of Common Hydrocarbon Fuels

A materials compatibility and thermal stability investigation was conducted using five common liquid hydrocarbon fuels and two structural materials. The tests were performed at the NASA Glenn Research Center Heated Tube Facility under environmental conditions similar to those encountered in regeneratively cooled rocket engines. Scanning-electron microscopic analysis in conjunction with energy dispersive spectroscopy (EDS) was utilized to characterize the condition of the tube inner wall surface and any carbon deposition or corrosion that was formed during selected runs. Results show that the carbon deposition process in stainless steel tubes was relatively insensitive to fuel type or test condition. The deposition rates were comparable for all fuels and none of the stainless steel test pieces showed any signs of corrosion. For tests conducted with copper tubing, the sulfur content of the fuel had a significant impact on both the condition of the tube wall and carbon deposition rates. Carbon deposition rates for the lowest sulfur fuels (2 ppm) were slightly higher than those recorded in the stainless steel tubes with no corrosion observed on the inner wall surface. For slightly higher sulfur content (25 ppm) fuels, nodules that intruded into the flow area were observed to form on the inner wall surface. These nodules induced moderate tube pressure drop increases. The highest sulfur content fuels (400 ppm) produced extensive wall pitting and dendritic copper sulfide growth that was continuous along the entire tube wall surface. The result of this tube degradation was the inability to maintain flow rate due to rapidly increasing test section pressure drops. Accompanying this corrosion were carbon deposition rates an order of magnitude greater than those observed in comparable stainless steel tests. The results of this investigation indicate that trace impurities in fuels (i.e. sulfur) can significantly impact the carbon deposition process and produce unacceptable corrosion levels in copper based structural materials.

Meyer, M. L.↗
DOE OSTI2021

Understanding fission gas bubble distribution, lanthanide transportation, and thermal conductivity degradation in neutron-irradiated α-U using machine learning

U—10Zr based metallic nuclear fuel is the leading candidate for next-generation sodium-cooled fast reactors in the United States. US research reactors have used and tested this fuel type since the 1960s and accumulated considerable experience and knowledge about the fuel performance. Most of the knowledge, however, remains empirical. The lack of mechanistic understanding of fuel performance puts a large burden on proof through experimental verification for the qualification of U—10Zr fuel for commercial use. Further, this paper proposes an image data-driven machine learning approach, coupled with domain knowledge provided by advanced post irradiation examination, to provide unprecedented quantified insights into the morphology, size, density and the connectivity of fission gas bubbles and their effects on the fission product transportation and thermal conductivity. Specifically, we developed a method to automatically detect, extract statistics, and classify ~19,000 fission gas bubbles into different categories, and quantitatively link the data to lanthanide transportation through connected bubbles and degradation of thermal conductivity along the radial temperature gradient in a neutron irradiated U—10Zr annular fuel. Results indicate the approach can be modified to study other irradiation effects, such as secondary phase redistribution and gaseous fuel swelling in other irradiated nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Influence of Fuel Properties on Gasoline Direct Injection Particulate Matter Emissions Over First 200 s of World-Harmonized Light-Duty Test Procedure Using an Engine Dynamometer and Novel “Virtual Drivetrain” Software

Abstract The influence of fuel properties on particulate matter (PM) emissions from a catalytic gasoline particulate filter (GPF) equipped gasoline direct injection (GDI) engine was investigated using novel “virtual drivetrain” software and an engine mated to an engine dynamometer. The virtual drivetrain software was developed in labview to operate the engine on an engine dynamometer as if it were in a vehicle undergoing a driving cycle. The software uses a physics-based approach to determine vehicle acceleration and speed based on engine load and a programed “shift” schedule to control engine speed. The software uses a control algorithm to modulate engine load and braking to match a calculated vehicle speed with the prescribed speed trace of the driving cycle of choice. The first 200 s of the World-harmonized Light-duty Test Procedure (WLTP) driving cycle was tested using six different fuel formulations of varying volatility, aromaticity, and ethanol concentration. The first 200 s of the WLTP was chosen as the test condition because it is the most problematic section of the driving cycle for controlling PM emissions due to the cold start and cold drive off. It was found that there was a strong correlation between aromaticity of the fuel and the engine-out PM emissions, with the highest emitting fuel producing more than double the mass emissions of the low PM production fuel. However, the post-GPF PM emissions depended greatly on the soot loading state of the GPF. The fuel with the highest engine-out PM emissions produced comparable post-GPF emissions to the lowest PM producing fuel over the driving cycle when the GPF was loaded over three cycles with the respective fuels. These results demonstrate the importance of GPF loading state when aftertreatment systems are used for PM reduction. It also shows that GPF control may be more important than fuel properties, and that regulatory compliance for PM can be achieved with proper GPF control calibration irrespective of fuel type.

Energy & Fuels↗
DOE OSTI2024

Scoping Studies on the Impacts of Increased Enrichment on Nuclear Criticality Safety

Fuel vendors and industry are increasingly interested in new fuel designs with increased enrichment. These fuel types are categorized as high-assay low-enriched uranium: their fuel enrichment is low in the regulatory sense, but it is much higher than industry’s typical operating enrichment bounds. It should be demonstrated that the appropriate mechanisms have been established to control this increased reactivity, and the conditions that arise from common operational occurrences must be considered. This report presents case studies that were conducted to determine whether increased burnable absorber loading can be used to offset increased enrichment. Increases in integral fuel burnable absorber and gadolinium bearing rods in pressurized water reactor (PWR) and boiling water reactor (BWR) assemblies must be examined. Increases in reactivity were shown to be feasibly controlled by increased burnable absorber loading, even when operational specificities were considered, as in BWR partial length rods and PWR annular fuel blankets.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1956

Coking of JP-4 fuels in electrically heated metal tubes

A limited exploratory investigation of the rate of coking of four JP-4 fuels in electrically heated metal tubes was conducted in order to provide design information for fuel prevaporizers for turbojet-engine combustors. The fuels tested included two production and two minimum-quality JP-4 type fuels. The heating tube was operated at fuel pressures of approximately 500, 400, and 50 pounds per square inch. The operating fuel temperature was varied between approximately 600 degrees and 1200 degrees F.

Smith, Arthur L↗
DOE OSTI2021

Modeling 233 Pa Generation in Thorium-fueled Reactors for Safeguards

Thorium has been considered as a possible alternative to uranium for nuclear fuel for many decades. It is three to four times more abundant in the earth than uranium and produces significantly less long-lived transuranic nuclear waste. Some claim thorium poses fewer proliferation concerns than other fuel types largely due to 232 U buildup (and associated high energy gamma-emitting decay products) in the irradiated thorium fuel. However, to fully explore potential proliferation concerns, generation and subsequent decay of 233 Pa produced in the reactor core still must be studied. With its half-life of 27 days, 233 Pa decays to 233 U, which is an International Atomic Energy Agency (IAEA) defined special fissionable material that can be used for nuclear weapons production. With more research being dedicated to thorium-fueled reactors, and several of these reactor designs possessing online fuel processing (allowing for on-site protactinium separation), it is important to understand this potential proliferation pathway. In particular, it is theoretically possible to extract protactinium from the irradiated fuel salt before it decays into 233 U. This hypothetical potential diversion can become an even greater proliferation concern if the extracted protactinium is purified through a second separation of protactinium approximately ten days later to remove the short half-life decay products of 232 Pa and 234 Pa, thus resulting in a higher concentration of the 233 Pa isotope, which decays into weapons usable 233 U with hardly any 232 U or 234 U in it. To estimate the concern of this potential proliferation challenge of thorium, different nuclear material accountancy techniques were reviewed for their viability to quantify 233 Pa if extracted from used thorium fuel. Characteristics of interest included technology maturity, cost, precision, and time taken to acquire results. Some technologies, like hybrid K-edge densitometry and passive gamma spectroscopy, appear to be viable techniques based on current literature. Due to the limited scope of this project, only passive gamma spectroscopy was further investigated. Three different reactor types (PWR, CANDU, MSR) were modeled with mixed thorium-uranium oxide fuels that were burned until the fuel was spent. The protactinium in the used fuel was extracted at the time of shutdown and the change in isotopic content of the protactinium quantified. Gamma spectroscopy simulations were performed for the protactinium isotopes and their decay products at various decay times. Given the simplicity of the models and large assumptions made (e.g. no background, no shielding, no self-attenuation), the initial results indicate that though 233 Pa is detectible for all the reactor types modeled at all decay times (0 to 300 days), more work should be done with higher fidelity models.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2026

A Multiphysics Evaluation of Annular Uranium-Zirconium Metallic Fuels [Poster]

This study examines the performance of U-10Zr annular metallic fuel rodlets which were experimentally evaluated as part of the Advanced Fuels Campaign (AFC). The AFC mission is to develop novel fuel technologies and facilitate the implementation of those technologies by industry partners. A key objective is to improve steady-state and transient performance over current fuel types. The experiments of interest in this study included annular metallic U-Zr fuel rodlets within HT-9 cladding which were placed in SS-316 capsules and inserted in the Advanced Test Reactor (ATR). Certain mechanical and thermal conditions cannot be directly evaluated through experiments and fuel performance modeling is used to shed light on this evolution over time. In this study, BISON Multiphysics simulations are leveraged to investigate the state of the fuel system throughout and after the experimental conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Assessment of Cladding-Cladding Delamination Failures in U-Mo Fuel Plates

Monolithic fuel is a candidate fuel form for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo alloy-based fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To qualify this fuel system, the program must demonstrate that the fuel meets the safety standards, has a predictable behavior, and performs well in a reactor. Although many plates have shown satisfactory thermo-mechanical performance in reactor, a small number of experimental plates exhibited failures, rendering performance of these plates unacceptable. Post-irradiation examinations of failed plates have revealed that various failures modes are present, including pillowing, blistering, buckling, warping, delamination, fracture, rupture, oxide spallation, etc. Previous studies have implied that such various operational and loading conditions could generate a complex stress-strain state, facilitating distinct failure modes that could impact the structural integrity. To understand such various failure modes, a comprehensive set of studies focusing on failure modes is being performed. As a part of these studies, this work studies the cladding-cladding separation failures that were observed in some of previous irradiation tests. To understand the root cause of cladding separation failures, selected plates from previous irradiation experiments were simulated under comparable operational conditions. Stress-strain state of the plates at the interface were examined. The results were comparatively evaluated to understand possible effects of stress state of the bond-line on delamination failures. This paper presents these findings, discusses such failure modes, and examines the influence of various factors on previously observed cladding delamination failures.

42 ENGINEERING↗
DOE OSTI2026

Impact of Molten Gallium on the Microstructure and Corrosion Behavior of Aluminum and Uranium-Aluminum Alloys for Used Nuclear Fuel Reprocessing

Test reactors around the world utilize highly enriched uranium fuel to achieve high neutron fluxes for materials testing. Once spent, the remaining uranium is a valuable resource for subsequent fuel fabrication. However, some of these test reactor cores consist of curved plate-type fuel elements, fabricated using aluminum alloy 6061 (AA6061) cladding to encapsulate a uranium-aluminum alloy (UAlx) fuel matrix. These assemblies require non-standard reprocessing approaches for uranium recovery, as aluminum dissolves readily in acidic solutions, generating large volumes of waste and complicating downstream chemical separations. In this work, we investigate a novel chemical decladding strategy based on the interaction between AA6061/UAlx and molten gallium (Ga). Ga is known to induce severe degradation of aluminum metal through liquid metal embrittlement (LME), even at relatively low Ga concentrations. By penetrating the aluminum crystal lattice, Ga disrupts grain cohesion and facilitates fracture or dissolution of the aluminum matrix. Thermodynamic analysis of the Al–Ga binary phase diagram suggests that Ga may offer a viable pathway to selectively weaken or dissolve the AA6061 cladding, and potentially the aluminum component of the UAlx fuel matrix within. To this end, parametric experiments were performed at 50 °C and 100 °C across a range of Al–Ga atomic fractions. At lower Al fractions, the AA6061 was completely molten after 2 hours of exposure to the Ga metal. In contrast, samples with higher Al fractions (0.9 Al, 0.1 Ga) contained residual solids after 2 hours, which were characterized by microstructural examination using electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). These Al-Ga compositions were also evaluated using FactSage thermodynamic modeling to further elucidate the relationship between phase diagram behavior and LME.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2005

RP-1 Thermal Stability and Copper Based Materials Compatibility Study

A series of electrically heated tube tests was performed at the NASA Glenn Research Center s Heated Tube Facility to investigate the effect that sulfur content, test duration, and tube material play in the overall thermal stability and materials compatibility characteristics of RP-1. Scanning-electron microscopic (SEM) analysis in conjunction with energy dispersive spectroscopy (EDS) were used to characterize the condition of the tube inner wall surface and any carbon deposition or corrosion formed during these runs. Results of the parametric study indicate that tests with standard RP-1 (total sulfur -23 ppm) and pure copper tubing are characterized by a depostion/deposit shedding process producing local wall temperature swings as high as 500 F. The effect of this shedding is to keep total carbon deposition levels relatively constant for run times from 20 minutes up to 5 hours, though increasing tube pressure drops were observed in all runs. Reduction in the total sulfur content of the fuel from 23 ppm to less than 0.1 ppm resulted in the elimination of deposit shedding, local wall temperature variation, and the tube pressure drop increases that were observed in standard sulfur level RP-1 tests. The copper alloy GRCop-84, a copper alloy developed specifically for high heat flux applications, was found to exhibit higher carbon deposition levels compared to identical tests performed in pure copper tubes. Results of the study are consistent with previously published heated tube data which indicates that small changes in fuel total sulfur content can lead to significant differences in the thermal stability of kerosene type fuels and their compatibility with copper based materials. In conjunction with the existing thermal stability database, these findings give insight into the feasibility of cooling a long life, high performance, high-pressure liquid rocket combustor and nozzle with RP-1.

Stiegemeier, B. R.↗
DOE OSTI2025

Microstructurally validated stable and predictable swelling in low-enriched uranium monolithic U-10Mo fuel mini-plates

Qualification of the low-enriched uranium (LEU) monolithic U-10 wt%Mo (U-10Mo) plate-type fuel system requires a demonstration of a stable and predictable fuel swelling behavior over the anticipated operating conditions of the United States high-performance research reactors (USHPRRs) selected for conversion to LEU operation. This will allow each reactor to develop appropriate safety margins that will retain fuel element lifetime coolability. Additionally, the fuel system must maintain performance attributes when fabricated at a commercial scale. The Mini-plate 1 experiment represents the first irradiation test of commercially fabricated miniaturized monolithic LEU U-10Mo fuel plates. Here, the swelling behavior within this experiment was compared against that of historical fuel developmental tests to reveal that the commercially fabricated fuel performed within the current recommended U-10Mo swelling model's predictions. Additionally, the fuel microstructural evolution was evaluated to link initial conditions to subtle variations detected in the swelling response, providing validation and confidence that the fuel system is robust.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Recommendations for a Fundamental Nuclear Material Control (FNMC) Plan for TRISO Fuel Fabrication Facilities Under NRC Regulations

A fundamental nuclear material control (FNMC) plan, which is required for all fuel fabrication facilities that are authorized to possess more than 1 effective kg of special nuclear material, describes how material control and accounting (MC&A) requirements will be met to comply with US Nuclear Regulatory Commission (NRC) regulations. Tristructural isotropic (TRISO) fuel fabrication facilities are likely to have issues in meeting MC&A requirements because of the new processes and fuel types their work involves. This report provides recommendations for an FNMC plan specifically for a TRISO fuel fabrication facility under NRC regulations and includes a draft outline of an FNMC plan. This report was produced for the Materials Protection, Accounting, and Control Technologies (MPACT) program under the Nuclear Fuel Cycle Technologies programs within the US Department of Energy’s Office of Nuclear Energy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Dynamic Probabilistic Risk Assessment Based Response Surface Approach for FLEX and Accident Tolerant Fuels for Medium Break LOCA Spectrum

After the Fukushima Daiichi Accident, the safety features such as accident tolerant fuel (ATF) and diverse and flexible coping strategies (FLEX) for existing nuclear fleets are being investigated by the US Department of Energy under the Light Water Reactor Sustainability Program. This research is being conducted to quantify the risk-benefit of these safety features. Dynamic probabilistic risk assessment (DPRA)-based response-surface approach has been presented to quantify the FLEX and ATF benefits by estimating the risk associated with each option. ATFs with multilayered silicon carbide (SiC), iron-chromium-aluminum, and chromium-coated zirconium cladding were considered in this study. While these ATF candidates perform better than the current zirconium cladding (Zr), they may introduce additional failure modes in some operating conditions. The fuel failure analysis modules (FAMs) were developed to investigate ATF performance. The dynamic risk assessments were performed using RAVEN, a DPRA tool, coupled with RELAP5 and FAMs. A cumulative distribution function-based index provided a mean of comparing the benefits of safety enhancements. For medium break loss of coolant accidents, FLEX operational timing window for each fuel type was estimated. Among these ATF candidates, SiC-type ATF was the most beneficial candidate for an increased safety margin than Zr-based fuel and was found to complement FLEX strategies in terms of risk and coping time.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Reburning of Animal Waste Based Biomass with Coals for NO x Reduction, Part II: Dairy Biomass (DB) and Coal–DB Blends

Concentrated animal feeding operations (both slaughter and dairy cattle) lead to land, water, and air pollution if waste storage and handling systems are not effectively managed. At the same time, cattle biomass (CB), which includes both slaughter/feedlot biomass (FB) and dairy biomass (DB), have the potential to be a source of green energy at coal-fired power plants. Part I presented results on NOx reductions with pure FB or Coal: FB blends as reburn fuels. Part II deals with results from reburning with pure DB or Coal: DB blends as reburn fuels. A mixture of NG with a small amount of NH3 was used to generate the baseline NOx of 400–420 ppm (or 185–194 g/GJ). NOx emissions were found to be reduced by as much as 96% when reburning with FB. The effects of reburn fuel type, equivalence ratio (ER RBZ ) in the reburn zone, vitiated air, several injection configurations of reburn fuel and initial NO concentrations on NOx emissions were investigated. The ER RBZ shows a significant effect on the NOx reduction. The 20% heat input by reburning was the better operating condition for the long-term operation due to its ash production. The results reveal that reburn with DB fuels is an effective technology for NOx emission control when the initial NOx emission is higher than 275 ppm (or 127 g/GJ or 0.3 lb/MMBtu).

09 BIOMASS FUELS↗
NASA NTRS1990

Propulsion challenges and opportunities for high-speed transport aircraft

The major challenges confronting the propulsion community for supersonic transport applications are identified. Both past progress and future opportunities are discussed in relation to perceived technology shortfalls for an economically successful SST that satisfies environmental constraint. A very large improvement in propulsion system efficiency is needed both at supersonic cruise and subsonic cruise conditions. Toward this end, several advanced engine concepts are being considered that promise up to 25 pct. better efficiency than the Concorde engine. The quest for high productivity through higher speed is also thwarted by the lack of a conventional, low priced fuel that is thermally stable at the higher temperatures associated with faster flight. Extending Jet A type fuel to higher temperatures and the adoption of liquid natural gas or methane are two possibilities requiring further study. Airport noise remains a tough challenge because previously researched concepts fall short of achieving FAR 36 Stage III noise levels. Innovative solutions may be necessary to reach acceptably low noise.

Strack, William C.↗
NASA NTRS1992

Effects of chemical equilibrium on turbine engine performance for various fuels and combustor temperatures

A study was performed to quantify the differences in turbine engine performance with and without the chemical dissociation effects for various fuel types over a range of combustor temperatures. Both turbojet and turbofan engines were studied with hydrocarbon fuels and cryogenic, nonhydrocarbon fuels. Results of the study indicate that accuracy of engine performance decreases when nonhydrocarbon fuels are used, especially at high temperatures where chemical dissociation becomes more significant. For instance, the deviation in net thrust for liquid hydrogen fuel can become as high as 20 percent at 4160 R. This study reveals that computer central processing unit (CPU) time increases significantly when dissociation effects are included in the cycle analysis.

Tran, Donald H.↗
NASA NTRS1954

Starting characteristics and combustion performance of magnesium slurry in 6.5-inch-diameter ram-jet engine mounted in connected-pipe facility

The starting characteristics and combustion performance of slurry type fuels, consisting of 50 percent magnesium powder in a hydrocarbon carrier, have been investigated in a flight-type, 6.5-inch-diameter ram-jet engine in a connected-pipe facility. Quick, dependable starting of the engine was obtained by the use of a disk which blocked part of the combustor area downstream of the flame holder. Acceptable performance was achieved with a short fuel-air mixing length by the development of a fuel-distribution control sleeve.

COMBUSTION - RAM-JET ENGINES↗