Search NASA⌕ Search

SEARCH · Search NASA

Results for “gust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Benchmark Solution For The Category 3, Problem 2: Cascade - Gust Interaction

The benchmark solution for the cascade-gust interaction problem is computed using a linearized Euler code called LINFLUX. The inherently three-dimensional code is run in the thin-annulus limit to compute the two-dimensional cascade response. The calculations are carried out in the frequency-domain and the unsteady response at each of the gust s three frequency component is computed. The results are presented on modal basis for pressure perturbations (i.e., acoustic modes) as well as velocity perturbations (i.e., convected gust modes) at each frequency.

Envia, Edmane↗
NASA NTRS1948

Calculations of the Dynamic Stress of Several Airplane Wings in Various Gusts

A series of calculations of the dynamic response of airplane wings to gusts were made with the purpose of showing the relative response of a reference airplane, the DC-3 airplane, and of newer types of airplanes represented by the DC-4, DC-6, and L-49 airplanes. Additional calculations were made for the DC-6 airplane to show the effects of speed and altitude. On the basis of the method of calculation used and the conditions selected for analysis, it is indicated that: 1) The newer airplanes show appreciably greater dynamic stress in gusts then does the reference airplane; 2) Increasing the forward speed or the operating altitude results in an increase of the dynamic stress ratio for the gust with a gradient distance of 10 chords.

Pierce, Harold B.↗
NASA NTRS1997

Measurement of Gust Response on a Turbine Cascade

This in-house experiment on the gust response of an annular turbine cascade was particularly designed to provide data to compare with the results of a typical, linearized gust-response analysis. Reduced frequency, Mach number, and incidence were varied independently. Except for the lowest reduced frequency, the gust velocity distribution was nearly sinusoidal. For the high inlet-velocity series of tests, the cascade was near choking. The mean flow was documented by measuring blade surface pressures and the cascade exit flow, and high-response pressure transducers were used to measure the unsteady pressure distribution. Inlet-velocity components and turbulence parameters were measured using hot wire anemometry. In addition to the synchronous time-averaged pressure spectra, typical power spectra are included for several representative conditions.

Kurkov, Anatole P.↗
NASA NTRS2006

Exploratory Studies in Generalized Predictive Control for Active Gust Load Alleviation

The results of numerical simulations aimed at assessing the efficacy of Generalized Predictive Control (GPC) for active gust load alleviation using trailing- and leading-edge control surfaces are presented. The equations underlying the method are presented and discussed, including system identification, calculation of control law matrices, and calculation of commands applied to the control effectors. Both embedded and explicit feedforward paths for inclusion of disturbance effects are addressed. Results from two types of simulations are shown. The first used a 3-DOF math model of a mass-spring-dashpot system subject to user-defined external disturbances. The second used open-loop data from a wind-tunnel test in which a wing model was excited by sinusoidal vertical gusts; closed-loop behavior was simulated in post-test calculations. Results obtained from these simulations have been decidedly positive. In particular, results of closed-loop simulations for the wing model showed reductions in root moments by factors as high as 1000, depending on whether the excitation is from a constant- or variable-frequency gust and on the direction of the response.

Kvaternik, Raymond G.↗
NASA NTRS2012

Survey of Applications of Active Control Technology for Gust Alleviation and New Challenges for Lighter-weight Aircraft

This report provides a historical survey and assessment of the state of the art in the modeling and application of active control to aircraft encountering atmospheric disturbances in flight. Particular emphasis is placed on applications of active control technologies that enable weight reduction in aircraft by mitigating the effects of atmospheric disturbances. Based on what has been learned to date, recommendations are made for addressing gust alleviation on as the trend for more structurally efficient aircraft yields both lighter and more flexible aircraft. These lighter more flexible aircraft face two significant challenges reduced separation between rigid body and flexible modes, and increased sensitivity to gust encounters due to increased wing loading and improved lift to drag ratios. The primary audience of this paper is engineering professionals new to the area of gust load alleviation and interested in tackling the multifaceted challenges that lie ahead for lighter-weight aircraft.

Regan, Christopher D.↗
NASA NTRS2013

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression

of a two part document. Part 2 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models, Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation." A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a semispan, aeroelastically scaled, wind tunnel model of a flying wing SensorCraft vehicle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree of freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid body modes. Gust load alleviation (GLA) and Body freedom flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Scott, Robert C.↗
NASA NTRS2014

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation

This is part 2 of a two part document. Part 1 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression." A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind tunnel model of a joined wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind tunnel model was mated to a new, two degree of freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at10 percent static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free flying wind tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Scott, Robert C.↗
NASA NTRS2018

Aeroservoelastic Optimization under Stochastic Gust Constraints

This work considers the aeroservoelastic optimization of a highly flexible transport aircraft wingbox with several control surfaces distributed along the trailing edge. The steady deflections of the control surfaces are designed to alleviate static maneuver loads, while the unsteady deflections are designed to alleviate stochastic continuous gust disturbances. Spatially-detailed unsteady stochastic stress and panel buckling constraints are formulated via modal acceleration, and by methods to locate the most-probable failure point along an equal-probability hypersurface. For the case considered here, it is found that the inclusion of such gust constraints during optimization presents a sizable structural mass penalty. In some cases, this mass penalty can be completely recovered with controlled gust load alleviation.

Stanford, Bret K.↗
NASA NTRS2020

Progress on Gust Load Alleviation Wind Tunnel Experiment and Aeroservoelastic Model Validation for a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper discusses a wind tunnel experiment of active gust load alleviation of a flexible wing which took place at University of Washington (UW) in 2019. The experiment performed under a NASA SBIR contract with Scientific Systems Company, Inc (SSCI). The objective of the experiment is to demonstrate active controls of the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system for gust load alleviation and real-time drag optimization. The wind tunnel model is a 8.2% sub-scale Common Research Model (CRM) wing. The wing structure is designed to provide a substantial degree of flexibility to represent that of a modern high-aspect ratio wing. Eight active control surfaces are employed in the VCCTEF. A new gust generator system was designed and installed by UW under a sub-contract with SSCI. The first test entry started in July 2019 and ended in September 2019. During this test entry, many significant issues were found with the hardware and software. The significant issues with the servos prevented the test objective from being completed. A follow-up second test entry in 2020 is being planned. The wing system is being repaired by SSCI. This paper reports on the progress of this experimental effort and the aeroservoelastic (ASE) model validation which was conducted during the test entry.

Nguyen, Nhan↗
NASA NTRS1957

Investigation at Low Speeds of Deflectors and Spoilers as Gust Alleviators on a Model of the Bell X-5 Airplane with 35 Degree Swept Wings and on a High-aspect-ratio 35 Degree Swept-wing-fuselage Model

Results of an investigation at low speeds to determine the gust-alleviation capabilities (reduction in lift-curve slope) of spoilers and deflectors on a 35 degree swept-wing model of high aspect ratio and on a 1/4-scale model of the X-5 airplane with 35 degree swept wings indicate that deflector and spoiler-deflector types of controls can be designed to provide considerable gust alleviation for a swept-wing airplane while still maintaining stability and control.

CONTROLS, SPOILER - COMPLETE WINGS↗
NASA NTRS1956

Calculation of the forces and moments on a slender fuselage and vertical fin penetrating lateral gusts

A theory is presented for calculating the variation with frequency of the lateral-force and yawing-moment coefficients due to sinusoidal side gusts passing over the profile of a simple fuselage-vertical-fin combination. The analysis is based on slender-body theory. The method considers the penetration effect of both fuselage and vertical tail in calculating side force and yawing moment due to side gusts, as opposed to a simple lag concept which considers the flow angle to be uniform over the configuration.

STABILITY, LATERAL AND DIRECTIONAL - DYNAMIC↗
NASA NTRS1956

Calculation and Compilation of the Unsteady-lift Functions for a Rigid Wing Subjected to Sinusoidal Gusts and to Sinusoidal Sinking Oscillations

The total lift responses to sinusoidal sinking oscillations and to sinusoidal gusts have been calculated, largely from existing information, for wings of various plan forms in subsonic and supersonic flow. For most of the cases considered, closed-form expressions are given and the final results are presented in the form of plots of the square of the modulus of the lift coefficient for wings in a sinusoidally oscillating gust field and in the form of the real and imaginary parts of the lift coefficient for wings undergoing sinusoidal sinking oscillations.

LOADS, GUST - WINGS↗
NASA NTRS1951

Influence of static longitudinal stability on the behavior of airplanes in gusts

The equations of motion for an airplane penetrating a gust are derived using a few simplifying assumptions. Calculations of loads for different static longitudinal stability on two German airplane models, HC 45 and HS 122, are compared with flight tests. Good agreement is obtained between the trend of the flight tests and the calculated values; however no absolute comparison was possible between the flight tests and calculations.

LOADS, GUST - HENSCHEL 122↗
NASA NTRS1974

Prediction of unsteady airloads for oblique blade-gust interaction in compressible flow

The techniques of Galilean-Lorentz transformation and matched asymptotic expansions are used to simplify the procedure of calculating the lift and pressure distribution induced on an infinite-span thin wing interacting with an oblique sinusoidal gust in subsonic flow. This technique requires that the product of the flow Mach number and the reduced frequency be small. Under this condition, the inner region of the transformed space behaves as an incompressible flow, so that existing incompressible flow theories can be used as a basis to construct closed-form solutions for the airload induced on the wing. This approach is an extension of the GASP approximation developed by Amiet and Sears (1970). Results are obtained for both the magnitude and the phase of the unsteady lift due to interaction with gust. These results are compared with available numerical results. Some discrepancies are noted and discussed.

Chu, S.↗
NASA NTRS1975

Three-dimensional dynamics of scientific balloon systems in response to sudden gust loadings

A mathematical model was developed of the three-dimensional dynamics of a high-altitude scientific research balloon system perturbed from its equilibrium configuration by an arbitrary gust loading. The platform is modelled as a system of four coupled pendula, and the equations of motion were developed in the Lagrangian formalism assuming a small-angle approximation. Three-dimensional pendulation, torsion, and precessional motion due to Coriolis forces are considered. Aerodynamic and viscous damping effects on the pendulatory and torsional motions are included. A general model of the gust field incident upon the balloon system was developed. The digital computer simulation program is described, and a guide to its use is given.

Dorsey, D. R., Jr.↗