Search NASA⌕ Search

SEARCH · Search NASA

Results for “heat simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A Cold Moderator For Sub-Thermal Neutron Flux Enhancement at the RPI-LINAC

The importance of high-quality thermal neutron scattering kernels coupled with a lack of accurate sub-thermal total cross section data prompted researchers at Rensselaer Polytechnic Institute (RPI) to design a cold moderation system to enhance sub-thermal neutron flux (defined as flux below 5 meV), for nuclear data measurements at the RPI Gaerttner LINAC facility. Using a series of neutronic and heat transfer simulations obtained with MCNP and COMSOL, an optimized final design was produced. The final design exceeded current target sub-thermal neutron producing capabilities by a factor of 8 in the sub-thermal region and is easily configurable with existing neutron producing targets.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

3D modeling of n = 1 RMP driven heat fluxes on the SPARC tokamak PFCs using HEAT

3D heat flux calculations at the lower outer divertor plate of SPARC using the HEAT code show that 3D fields generated from error field correction coils can lead to enhanced peak heat fluxes up to 15 times larger compared to the axisymmetric case. Previously employed to simulate axisymmetric heat flux on 3D plasma facing components, the HEAT code can now predict 3D heat flux generated by non-axisymmetric plasmas. This is achieved via a new HEAT module which leverages the 3D field line tracing capabilities of MAFOT starting from an M3D-C1 (MHD resistive code) perturbed equilibria. The resulting heat flux is assigned using the magnetic footprint and the heat flux layer model, an extension of the 2D heat flux model also known as the Eich, to 3D non-axisymmetric plasmas. For SPARC, the new capabilities of HEAT are used to calculate the 3D heat loads resulting from n = 1 perturbation fields (with n indicating the toroidal periodicity) applied through a toroidal array of six picture frame coils with different amplitude. The comparison with the unperturbed case shows significant changes in shape and intensity of the heat flux profile. The results show that the application of n = 1 3D field leads to a localized enhancement of the heat flux peak, influenced by the wetted area impacted by the magnetic footprint, and the appearance of a secondary heat flux peak, whose intensity depends on amplitude of the applied 3D field and toroidal location.

3D heat flux↗
DOE OSTI2021

Granular Flow

LIGGGHTS-INL is a capability-extended version of LIGGGHTS. LIGGGHTS is an Open Source Discrete Element Method Particle Simulation Software (https://www.cfdem.com/media/DEM/docu/Manual.html). LIGGGHTS stands for LAMMPS improved for general granular and granular heat transfer simulations. LAMMPS is a classical molecular dynamics simulator. It is widely used in the field of Molecular Dynamics (https://lammps.sandia.gov/doc/Manual.html). Thanks to physical and algorithmic analogies, LAMMPS is a very good platform for DEM simulations. LAMMPS offers a GRANULAR package to perform these kinds of simulations. LIGGGHTS aims to improve those capability with the goal to apply it to industrial applications.

Xia, Yidong↗
DOE OSTI2021

A simulation-based assessment of technologies to reduce heat emissions from buildings

Heat emissions from buildings are part of anthropogenic heat leading to urban overheating. This paper aims to assess how technologies (i.e., energy conservation measures - ECMs), used to decrease energy use, may also reduce heat emissions from buildings. This study employs the physics-based engine EnergyPlus to simulate the main components of heat emissions from buildings to ambient air: envelope, zone, and systems. Hourly simulations are run for IECC single- and multi-family reference models with three representative climates: Miami, Baltimore, and Chicago. The results show that the performance of ECMs varies among weather, seasons, and residential typologies. Particularly, some ECMs (i.e., cool coatings, heat pumps, additional insulation, energy-awareness occupants) show a strong decrease in heat emissions, yet they are not always correlated with proportional decreases in energy use. When all ECMs are combined, the reductions are larger on heat emissions (89%) than on site energy (65%) from the base cases. During summer in Miami, the combination of ECMs shows a decrease in heat emissions from the building surface component of 80% during daytime, 92% for the HVAC component and a counterbalanced increase in the zone component of 88%, bringing to a daily decrease in total heat emissions. The main contributions of this study are quantifying how typical ECMs influence residential building heat emissions using EnergyPlus simulations and informing urban planners and stakeholders on prioritizing measures for mitigating urban overheating problems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Thermal-Hydraulic Analysis of the AFIP-7 Irradiation Test in the Advanced Test Reactor - Oxide Growth Prediction and Correlation

Knowing the thickness of the oxide layer on the surface of aluminum fuel cladding is vitally important for predicting fuel temperature due to the low thermal conductivity of the oxide layer. Several correlation models for predicting oxide growth can be found in the literature. In previous research, the correlations were combined with heat transfer simulations in Abaqus, a finite element analysis code, to forecast the oxide growth. However, this approach requires heat transfer coefficients for modeling heat exchanges with the external flow field, and such coefficients were obtained through empirical equations. Since different empirical equations yield varying heat transfer coefficients, the cladding temperature and predicted oxide thickness both carry a high degree of uncertainty. Here, this research develops a new approach that integrates the fluid flow, fluid and solid heat transfer, and oxide growth correlation(s) into a single computational fluid dynamics model. We demonstrate this approach’s ability to predict oxide development on the AFIP-7 plates during two Advanced Test Reactor (ATR) irradiation cycles. The projected oxide thickness falls within the experimental measurements taken during post irradiation examination.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Three-Phase Modeling in Sockeye

The heat pipe simulation tool Sockeye is given the capability to allow the presence of the solid phase of the heat pipe working fluid, which is necessary for modeling transients to and from room temperature, since microreactor designs feature high-temperature heat pipes employing metal working fluids. The liquid phase equations are converted to equations for the mixture of liquid and solid phases, with a simple latent heat relation determining the fractions of these phases. This capability is introduced while preserving equivalent solutions for the liquid-vapor regime. Theory is presented, along with numerical examples to illustrate the propagation of a melt front and startup from the solid state.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

High-Fidelity Modeling and Experiments to Inform Safety Analysis Codes for Heat Pipe Microreactors

Heat pipe microreactors are reactor designs that primarily use liquid-metal heat pipes to cool the core. The main interest in heat pipes is the fact that they can remove heat passively. This, along with the use of liquid metal, allows the reactor to operate at higher temperatures. Although the use of heat pipes in nuclear reactors is new, liquid-metal heat pipe technology is mature. Nevertheless, experimental data on heat pipes are scarce, and very little is known about their behavior during abnormal operations and close to their thermal limits. Therefore, new experiments and accurate heat pipe simulations are needed to develop reliable closure models. This work describes a joint experimental and numerical investigation into heat pipes that attempts an initial closure of this gap. Further, the numerical and experimental efforts are currently proceeding in parallel, aimed at different aspects of heat pipes. The numerical part is focused on gaps in local closures, and the experiments capture the overall heat pipe behavior.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Heat Pipe Cooled Microreactors

Microreactor technologies are required to provide reliable carbon-free power generation in remote applications. The heat pipe cooled microreactor concept in particular offers notable advantages due to the passive operation of heat pipes enabling increased reliability and simplicity in a more compact form factor. There is a significant need for experimental work to aid and expedite the deployment of heat pipe microreactors due to their unique technological characteristics. Thus, there has been increased interest in heat pipe experiments by numerous institutions in order to support these efforts. The present work is a comprehensive review of heat pipe experiments, describing instrumentation, methods, phenomena of interest, and recent developments. In addition, legacy work on the operation of high-temperature heat pipes under irradiation is reviewed and discussed. Furthermore, the verification and validation efforts for the flagship heat pipe simulation code Sockeye are reviewed and requirements for future experiments are outlined. Lastly, future directions are proposed for heat pipe experimentation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Exascale-capable cellular automaton for nucleation and grain growth

This model is a cellular automata-based algorithm used to predict grain-scale microstructure development. Nucleation and growth of existing grains are considered in an initially liquid domain, where the temperature field evolution is either driven through heat transport simulation data or a frozen temperature approximation (i.e., a constant cooling rate and a fixed thermal gradient). The growth of grains is based on the decentered octahedron algorithm published by Gandin and Rappaz (https://doi.org/10.1016/S1359-6454(96)00303-5), where the grain envelopes are tracked as approximations of the evolving dendritic growth front. The input heat transport data, which can come from simulation of an arbitrary processing technique, consists of coordinates and times at which said coordinates fall below the liquidus and solidus temperatures for the final time. As a result, only the final solidification of a given region is modeled (no remelting). The code is designed to be compatible with pre-Exascale architectures, and uses MPI and the Kokkos library to decompose the computational domain and offload solidification calculations to GPUs.

Rolchigo, MatthewR.↗
DOE OSTI2024

An MPMD approach coupling electromagnetic continuum mechanics approximations in ALEGRA

In this work, two complementary approximations for describing aspects of continuum electromagnetics in moving media are discussed: electroquasistatic and magnetoquasistatic. Each has been implemented in the finite element shock code ALEGRA for modeling dynamic electromechanical phenomena on typical engineering time scales, with fully integrated circuit coupling. The approximations can be obtained by consistent asymptotic balancing of Maxwell’s equations relative to timescales associated with magnetic diffusion, charge relaxation, and electromagnetic wave propagation. In ALEGRA, the electroquasistatic approximation is used for ferroelectric (FE) modeling, while the magnetoquasistatic approximation is used for magnetohydrodynamic (MHD) modeling. In this paper we introduce for the first time a detailed derivation of a useful quasi-steady “low-R m ” variant of the MHD approximation applicable for cases, such as with detonators, where the thermodynamic pressure arising from Joule heating dominates over magnetic forces. An additional purpose of this paper is to present a coupling mode using Multiple Program-Multiple Data (MPMD) message passing communication that allows the user to run 3D FE problems together with 2D and/or 3D MHD problems with the respective simulation domains coupled through a common circuit equation. The MPMD coupling capability is used here to model the dynamic coupling of a notional ferroelectric generator with an RP-87 exploding bridgewire detonator. The simulated bridgewire heats up and bursts under current generated by simulated depoling of the ferroelectric generator, as a demonstration of the MPMD capability.

42 ENGINEERING↗
DOE OSTI2024

Development & Experimental Validation of a Generalized Resistance-Capacitance Model for Numerical Simulation of Phase-Change Material Embedded Heat Exchangers

Latent heat thermal energy storage (LHTES) using phase change material (PCM) has attracted increased attention as a viable solution for overcoming the mismatch between energy supply and demand for renewable energy-based systems. PCM-embedded heat exchangers (PCM-HX) have the potential to significantly improve thermal performance due to high storage capacity and low temperature variation during the phase change process. Most models for simulating LHTES heat transfer use Computational Fluid Dynamics (CFD) simulations, which have high computational costs resulting from considering the complex and time-dependent physics relevant to PCM-HXs. In this paper, a Generalized Resistance Capacitance-based Model (GRCM) was developed to predict the thermal performance of arbitrary PCM-HXs in a computationally efficient manner without compromising modeling accuracy. The GRCM is exercised for three case studies: (i) verification for a single-slabbed finned PCM-HX, (ii) verification and validation for a copper foam/paraffin composite PCM-HX, and (iii) validation for a straight tube annular finned PCM-HX. The copper foam PCM-HX uses an electric heater at the top of HX, while the other two configurations utilize water as heat transfer fluid. For the single-slabbed finned PCM-HX melting case, the mean deviation in average PCM temperature predicted by the GRCM compared to the CFD model was between 0.56 – 0.73 K, with maximum temperature deviation of 2.68 K. For the HTF outlet temperature, the validation results showed that GRCM prediction matches very well with experimental data, with mean temperature deviation of 0.24 K during melting case, while for solidification case was 0.34 K. These results showcase the GRCM’s capability for accurately reproducing the thermal characteristics of PCM-HXs with considerably lower computational effort.

42 ENGINEERING↗
DOE OSTI2020

A Novel Approach to Modeling Biomass Pyrolysis in a Fluidized Bed Reactor

A novel approach to simulating biomass pyrolysis in a fluidized bed of mostly inert material is presented. The bed is assumed to be externally heated, although simulation of autothermal operation with partial oxidation of the products is a future objective. Combining pyrolysis reaction kinetics developed by the CRECK Modeling Group and a previously published component properties model, material and energy balances are closed by tracking the residence time of biomass particles without regard for their exact spatial distribution. The model is used to simulate a pilot-scale fluidized bed pyrolysis process being developed at Iowa State University, and model predictions are compared with experimental results for red oak and corn stover feedstocks. The results are in general agreement, with the model typically predicting more noncondensable gas and less low-boiling liquid products. The differences are ascribed to the limitations of the kinetics model. This model provides a rigorous energy balance for fluidized bed pyrolysis processes that can be incorporated into commercial flowsheet models with the capacity for future addition of partial oxidation reactions and implementation of improved kinetics models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The reactivity of experimentally reduced lunar regolith simulants: Health implications for future crewed missions to the lunar surface

Crewed missions to the Moon may resume as early as 2026 with NASA's Artemis III mission, and lunar dust exposure/inhalation is a potentially serious health hazard that requires detailed study. Current dust exposure limits are based on Apollo-era samples that spent decades in long-term storage on Earth; their diminished reactivity may lead to underestimation of potential harm that could be caused by lunar dust exposure. In particular, lunar dust contains nanophase metallic iron grains, produced by “space weathering”; the reactivity of this unique component of lunar dust is not well understood. Herein, we employ a chemical reduction technique that exposes lunar simulants to heat and hydrogen gas to produce metallic iron particles on grain surfaces. We assess the capacity of these reduced lunar simulants to generate hydroxyl radical (OH*) when immersed in deionized (DI) water, simulated lung fluid (SLF), and artificial lysosomal fluid (ALF). Lunar simulant reduction produces surface-adhered metallic iron “blebs” that resemble nanophase metallic iron particles found in lunar dust grains. Reduced samples generate ~5–100× greater concentrations of the oxidative OH* in DI water versus non-reduced simulants, which we attribute to metallic iron. SLF and ALF appear to reduce measured OH*. The increase in observed OH* generation for reduced simulants implies high oxidative damage upon exposure to lunar dust. Low levels of OH* measured in SLF and ALF imply potential damage to proteins or quenching of OH* generation, respectively. Reduction of lunar dust simulants provides a quick cost-effective approach to study dusty materials analogous to authentic lunar dust.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Experimental Combustion and Flame Characterization of a Chemical Looping-Based Oxidative Dehydrogenation Byproduct Fuel Mixture Containing High CO2 Dilution

Abstract This study investigates the combustion performance of a CO2-rich fuel mixture containing ethane and methane as active species using a constant volume combustion chamber. This fuel is obtained as a byproduct of a chemical looping-based oxidative dehydrogenation (Cl-ODH) process ethylene production. The byproduct gas mixture has 40.79% CO2, 39.49% ethane, and 4.88% methane by weight with other minor compounds. Using this fuel for energy extraction would improve the process efficiency of the ethane to ethylene conversion. After initial combustion modeling, the gas fuel mixture was reduced to just the major species: CO2, ethane, and methane. The mixture was then tested for flammability limits and combustion performance under spark-ignition conditions. Effects of ambient conditions like temperatures between 300 and 400 K with initial pressures from 1 to 10 bar were tested. The effects of stoichiometry were tested to understand flame velocities and heat release. The fuel mixture showed an overall reduced flame velocity compared to gasoline. Instability in combustion was believed to be caused by the dissociation of ethane under elevated conditions. At higher pressures, the flame produces lower cumulative heat release. Simulations were also performed using a model tuned to replicate the operations of the combustion chamber used in the experiments. Heat release and unburnt fuel mass data were calculated to identify the discrepancies in the combustion completeness at elevated pressures. The effects of CO2 quenching the flame coupled with the increased dissociation of the fuel species can lead to up to more than 75% of the fuel mixture being unburnt. Data from this study were used to modify a small-scale spark-ignition engine to use this fuel and produce usable energy.

Energy & Fuels↗
DOE OSTI2021

Design, Flow Field, and Heat Transfer Characterization of the Conjugate Aero-Thermal Test Facility at NETL

A new aerothermal test facility was constructed for the purpose of studying film cooling performance in an environment that accurately simulates conjugate heat transfer characteristics that exist in engine operation. Here, this paper details the design of the facility and the plan for conducting steady state film cooling experiments to improve the understanding of conjugate heat transfer scaling from laboratory to engine conditions. The test facility consists of two separate low channels (hot gas/coolant) and each gas path has a flow conditioning section, a convergent nozzle and a test section/channel with viewports. Numerical simulations were conducted to predict flow field characteristics supporting the design of the flow loop facility. Preliminary experiments were conducted to characterize the flow field using velocity and temperature profile measurements. In addition, infrared (IR) thermography methods were developed to measure surface temperatures on the hot side of the test plate. The IR measurement methods including calibration of the IR camera is explained in detail. It was concluded that appropriate hot gas path flow conditioning could be achieved using a strainer-like tube, a perforated plate, and a honeycomb-mesh screen system upstream of the test section. Flow field measurements from preliminary experiments showed that the boundary layer profile follows the law of the wall.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Enhancement of disposal efficiency for deep geological repositories based on three design factors - Decay heat optimization, increased thermal limit of the buffer and double-layer concept

This study investigates the enhancement of disposal efficiency for deep geological repositories (DGRs) based on three design factors: decay heat optimization, increased thermal limit of the buffer, and double-layer concept using coupled thermo-hydro-mechanical (THM) numerical simulations. Decay heat optimization is achieved by iteratively emplacing spent nuclear fuels having the maximum and minimum decay heat in a canister. Disposal areas can be reduced by 20 % to 40 % compared to the current reference disposal system in Korea (KRS+) in accordance with the combinations of the three design factors, alleviating challenges in site selection for the DGR. This study additionally identifies an optimal layer spacing of 500 m for the double-layer concept in the viewpoint of the buffer temperature, where thermal interaction between the upper and lower layers nearly disappears. However, determining the ultimate disposal and layer spacing requires engineering judgement, considering not only the thermal performance of the DGR but also various factors such as cost and difficulties of the construction and rock mass stability. DGRs designed with an increased thermal limit of the buffer poses a greater probability of rock mass failure around disposal tunnels and deposition holes due to elevated thermal stresses. Densely arranged heat sources for the DGRs with enhanced disposal efficiency lead to larger temperature increase even at the far-field scale, raising a possibility of thermally driven fracture shear activation with associated hydraulic, mechanical, and seismic changes.

58 GEOSCIENCES↗
DOE OSTI2021

Clarification of creep deformation mechanism in heat-affected zone of 9Cr steels with In Situ experiments

This work quantified nonuniform creep deformation across the heterogeneous heat-affected zone (HAZ) of Grade 91 steel with sophisticated experiments, including an electric-thermal finite element model–assisted Gleeble thermomechanical simulation and a high-temperature creep testing with in situ digital image correlation (DIC). High temperature creep properties of HAZ sub-zones were quantitatively measured by the DIC. Furthermore, by utilizing peak temperature, hardness, local creep strain, and underlying microstructures, creep deformation mechanisms in HAZ were further understood. DIC measurements reveal a creep-vulnerable zone (CVZ) exposed to a peak temperature of 932°C (close to A C3 ) in the intercritical HAZ experienced the fastest creep strength degradation instead of the soft zone with the lowest hardness prior to creep. The significantly reduced precipitation strengthening from misplacement of undissolved and coarsened M 23 C 6 carbides led to a faster recrystallization of tempered martensite in the CVZ. Weak untransformed tempered martensite (ferrite grains) stabilized by local Cr enrichment from dissolved M 23 C 6 also harmed the CVZ's creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhancement of conventional concrete mix designs for sensible thermal energy storage applications

The study examines twenty-nine different concrete mix designs with varying constituents to improve thermal performance for energy storage at elevated temperatures up to 420 °C. Effects of variables including the type and volumetric percentage of coarse and fine aggregates, the type and replacement content of supplemental cementitious materials, water-to-cement ratio, the type and quantity of steel fiber reinforcement, and the inclusion of iron oxide powder are experimentally investigated by measuring the mechanical and thermal properties of each mix, with the overall goal of enhancing thermal performance and mitigating mechanical degradation for thermal energy storage (TES) applications. It is found that the use of siliceous aggregate with a high volumetric percentage produces the highest improvement (23 %–37 % at elevated temperatures) of concrete thermal conductivity, while silica fume replacement of Type I cement provides the highest improvement (4 %–8 % at elevated temperatures) of concrete specific heat. To simulate the operation of a TES system, thermal cycling was conducted to examine the change in concrete properties as a function of repetitive heating (during and after 50 total cycles to 420 °C). Based on the results of testing, concrete mix designs with high aggregate percentages (up to 72 % by volume), siliceous coarse aggregate, silica fume replacement of Type I cement (15 % by weight), and steel fiber reinforcement (up to 2 % by volume) facilitate enhanced TES performance by providing consistent thermal conductivity of ~2.2 W/m·K and specific heat of ~3.2 MJ/m 3 ·K under cyclic high temperature exposure.

25 ENERGY STORAGE↗